Razor E300 Users Manual
E200 to the manual 380e2266-e47f-412b-a022-ea75f8afdd8d
2015-02-02
: Razor Razor-E300-Users-Manual-443676 razor-e300-users-manual-443676 razor pdf
Open the PDF directly: View PDF 
.
Page Count: 24
| Download | |
| Open PDF In Browser | View PDF |
Owner’s Manual
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: E100/125/150 must be traveling
3mph before motor will engage. Kick start to
3mph then twist the throttle to start motor.
Item Numbers
E100
13100E-BL
E125
13125E-BK Black
13111110 Red
E150 13111612
E200
13200E-SL
E200S
13201S-SL
E225S
13112850
E300
13300E-SL
E300S
13301S-SL
E325S
13116390
Contents
Safety Warnings............................................................. 1
Before You Begin............................................................ 2
Assembly and Set-Up.................................................. 3-4
Repair and Maintenance............................................ 4-10
Troubleshooting Guide............................................. 11-12
E100, E150, E200 and E300 Scooter Parts............. 13-20
Safety Reminders........................................... Back Cover
Warranty......................................................... Back Cover
Safety Warnings
WARNING: Riding the E100, E200 or E300 scooter can be
a hazardous activity. Certain conditions may cause the equipment to
fail without fault of the manufacturer. Like other electric vehicles,
the scooter can and is intended to move, and it is therefore possible
to lose control, fall off and/or get into dangerous situations that no
amount of care, instruction or expertise can eliminate. If such things
occur you can be seriously injured or die, even when using safety
equipment and other precautions. RIDE AT YOUR OWN RISK AND
USE COMMON SENSE.
Failing to properly adjust and tighten the clamps and retainers that affix
the handlebars and folding system can cause you to lose control and
fall. When properly adjusted, you cannot twist the front wheel out of
line with the handlebars or move the T-tube out of adjustment. If you can
twist or force these components to move or come off by hand, readjust
and properly retighten clamp mechanisms.
Do not attempt or do stunts or tricks on your E100, E200 or E300 scooter.
The scooters are not made to withstand abuse from misuse such as
jumping, curb grinding or any other type of stunts.
This manual contains many warnings and cautions concerning the
consequences of failing to maintain, inspect or properly use your
E100, E200 or E300 scooter. Because any incident can result in serious
injury or even death, we do not repeat the warning of possible serious
injury or death each time such a possibility is mentioned.
Maintain a hold on the handlebars at all times.
Never carry passengers or allow more than one person at a time to ride
the scooter.
Never use near steps or swimming pools.
APPROPRIATE RIDER USE AND
PARENTAL SUPERVISION
This manual contains important safety information. It is your
responsibility to review this information and make sure that all riders
understand all warnings, cautions, instructions and safety topics and
assure that young riders are able to safely and responsibly use this
product. Razor recommends that you periodically review and reinforce
the information in this manual with younger riders, and that you
inspect and maintain your children’s vehicle to insure their safety.
Keep your fingers and other body parts away from the chain, drive chain,
steering system, wheels and all other moving components.
Never use headphones or a cell phone when riding.
Never hitch a ride with another vehicle.
Do not ride your scooter in wet or icy weather and never immerse
the scooter in water, as the electrical and drive components could be
damaged by water or create other possibly unsafe conditions.
The recommended rider ages of 8 and older for the E100 scooter and
12 and older for the E200 and E300 scooters are only estimates, and
can be affected by the rider’s size, weight or skills. Any rider unable to
fit comfortably on the scooter should not attempt to ride it.
A parent’s decision to allow his or her child to ride this
product should be based on the child’s maturity, skill and
ability to follow rules.
The E100, E200 and E300 scooters are intended for use on flat, dry
surfaces such as pavement or level ground without loose debris such
as sand, leaves, rocks or gravel. Wet, slick, bumpy, uneven or rough
surfaces may impair traction and contribute to possible accidents. Do
not drive your scooter in mud, ice, puddles or water. Avoid excessive
speeds that can be associated with downhill rides. Never risk damaging
surfaces such as carpet or flooring by use of an E100, E200 or E300
scooter indoors.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the vehicle.
Do not ride at night or when visibility is limited.
DO NOT EXCEED THE WEIGHT LIMIT OF 120 pounds for the E100 and
E150 scooter or 220 pounds for the E200 and E300 scooters.
PROPER RIDING ATTIRE
Always wear proper protective equipment such as an approved safety
helmet (with chin strap securely buckled), elbow pads and kneepads. A
helmet may be legally required by local law or regulation in your area.
A long-sleeved shirt, long pants, and gloves are recommended. Always
wear athletic shoes (lace-up shoes with rubber soles), never drive
barefooted or in sandals, and keep shoelaces tied and out of the way of
the wheels, motor and drive system.
Rider weight does not necessarily mean a person’s size is appropriate
to fit or maintain control of the scooter.
Do not touch the brakes or motor on your scooter when in use as
these parts can become very hot.
Refer to the section on safety for additional warnings.
USING THE CHARGER
The charger supplied with the E100, E200 or E300 scooter should be
regularly examined for damage to the cord, plug, enclosure and other
parts, and in the event of such damage, the bike must not be charged
until the charger has been repaired or replaced.
ACCEPTABLE RIDING PRACTICES AND
CONDITIONS
Always check and obey any local laws or regulations which
may affect the locations where the E100, E200 or E300 scooter
may be used.
Use only with the recommended charger.
Ride defensively. Watch out for potential obstacles that could catch
your wheel or force you to swerve suddenly or lose control. Be careful
to avoid pedestrians, skaters, skateboards, scooters, bikes, children or
animals who may enter your path, and respect the rights and property
of others.
The charger is not a toy.
Always disconnect from the charger prior to wiping down and cleaning
your scooter with liquid.
Do not activate the speed control on the hand grip unless you are on
the scooter and in a safe, outdoor environment suitable for riding. The
E100 scooter must be moving at 3 miles per hour before the motor
will start.
1
FAILURE TO USE COMMON SENSE AND HEED
THE ABOVE WARNINGS INCREASES RISK OF
SERIOUS INJURY. USE WITH APPROPRIATE
CAUTION AND SERIOUS ATTENTION TO SAFE
OPERATION.
Before You Begin
Remove contents from box. Remove the foam separators that protect the components from damage during
shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have
occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there
should not be any problems, even if the box has a few scars or dents.
Estimated Assembly and Set-Up Time
Razor recommends assembly by an adult with experience in bicycle mechanics.
Allow up to 20 minutes for assembly, not including initial charge time.
Allow up to 12 hours for initial charge (see page 3 for charging information.
Brake Lever
WARNING:
DO NOT USE NONRAZOR PRODUCTS WITH
YOUR RAZOR ELECTRIC
SCOOTER. The scooter has
been built to certain Razor design
specifications. The original
equipment supplied at the time of
sale was selected on the basis of
its compatibility with the frame,
fork and all other parts. Certain
aftermarket products may or may
not be compatible.
Speed Control
Brake Lever
Adjuster
T-tube
Handlebar height adjust
quick-release
Charger
Extension Tube
Charger
Port
Charger
Plug
Folding System
Locking Knob
Headset
On/off switch
and charging port
Front Fork
Battery pack
and motor
controller
Tire
Wheel
Required Tools
Some tools may be supplied; however, we recommend the use of mechanic’s grade tools. Use the supplied
tools only as a last resort.
6mm hexagonal
key wrench
(included)
Inflation valve
adapter/extender
(with E200 & E300
only)
Bicycle-style tire pump
for Schrader valve
tires, with pressure
gauge
Need Help? Visit our web site for updates and a list of authorized service centers at www.razor.com
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
2
Assembly and Set-Up
q Charging the Battery
Your electric scooter may not have a fully charged battery. Therefore it is a good idea to charge the battery
prior to use.
• Initial charge time: 12 hours
• Recharge time: up to 8 hours,
Battery should be recharged
a minimum of 8 hours after
each use. When the vehicle
is not in regular use, recharge
the battery at least once a
month until normal use
is resumed.
Charger
Port
Charger
Plug
• Run time: up to 40 minutes
• Average battery life: 250 charge/discharge cycles
2 Plug the charger plug into a
1 Plug the charger port into the
wall outlet.
port on the scooter. The charger
works with the power switch
in either the on or off position.
The charging input, on/off
switch and overload breaker are
located under the deck at the
front left-hand side.
WARNING: Always
disconnect your scooter from
the charger before cleaning with
liquid.
Note: If your charger does not
look like the one illustrated,
your unit has been supplied
with an alternative charger.
The specifications and charging
procedure would not change.
The charger has a small window
with one LED or two LEDs to
indicate the charge status.
Refer to the illustration on
the charger unit for the actual
“charging” and “charged” status
indications for your model
charger.
Chargers have built-in overcharge protection to prevent
battery from being over-charged.
Be sure to properly align the
groove on the charger input
plug with the corresponding
socket on the case;
otherwise, no charging
action will occur.
q Attaching the Handlebars
WARNING: Failure
to recharge the battery at least
once a month may result in
a battery that will no longer
accept a charge.
1 Loosen the locking knob
and swing to the 6 o’clock position to unfold the handlebar.
3 Slide the quill into the
2 Remove the plastic protector
fork until it bottoms on the
headset.
covering the base of the handlebar assembly. Insert the “quill”
part of the handlebar assembly
into the fork. You may have to
loosen the wedge to allow it to
slip into the fork.
WARNING: Failure
to properly tighten the wedge
may allow the handlebars to
dislodge while riding and may
cause you to lose control and
fall. When correctly tightened,
the handlebars will not rotate
out of alignment with the
front wheel under normal
circumstances.
WARNING: Keep your
fingers clear of the pivoting
mechanism when folding or
unfolding the scooter, and make
sure others are standing clear.
4 Using a 6mm hexagonal
key wrench, tighten the
wedge by turning the bolt
clockwise. The wedge is
properly tightened when the
handlebars cannot be twisted
out of alignment with the
front wheel.
6 Swing the locking knob to
5 Pivot the handlebar assembly
the 12 o’clock position and
tighten by hand as firmly as
possible.
upright.
3
Note: The cable and wire
assembly from the handlebar
must not wrap around the
steering tube or handlebar
as shown in step 3. Sharp
bends or twisting of the brake
cable can cause the brakes to
malfunction.
Assembly and Set-Up
q Adjusting the Handlebar Height (E100/E200/E300 only)
WARNING: Failure
to properly engage the quickrelease clamp may cause the
T-tube to move up or down
while riding, which may cause
you to lose control and fall.
With the quick-release properly
adjusted and engaged, the
handlebars will not move up or
down.
1
Pull the quick-release lever
outward.
3 The tension of the quick-
2 Slide the T-tube to the
release clamping mechanism
can be adjusted by tightening
or loosening the bolt with
your fingers.
desired position and secure by
pushing the quick-release lever.
Note: Be careful not to overtighten. You should be able
to open and close the quickrelease lever by hand, and the
T-tube should move up and
down freely with the quickrelease open.
q Riding Your Scooter
Testing the Brakes – To use the brakes, squeeze the front and back brake levers to increase the
pressure on the brake. The brake lever is fitted with a cable adjuster to compensate for cable stretch
and/or to fine-tune the lever movement to brake engagement. If brake is not engaging properly, follow
instructions for adjusting the brakes on page 5.
Note: The E100 must be going 3 mph before the motor will start. Kick to 3 mph then activate the speed
control while simultaneously pressing the green“go” button to engage the motor.
Repair and Maintenance
Check the Razor web site for any updates on the latest repair and maintenance procedures.
Turn power switch off before conducting any maintenance procedures.
q Adjusting the Brakes
1 To adjust the brake cable
play, thread the brake lever
adjuster in or out 1/4 to 1/2 turn
until the desired brake adjustment is attained. Most
adjustments are complete at
this step. If brake still needs
further adjustment, proceed to
step 2.
2 (E100)
2 (E125, E200 & E300)
Inspect the brake pads (A)
for proper alignment against
the wheel or excess wear. To
realign brake pads, loosen the
fixing nut (B) and adjust the pad
to contact the rim. Retighten
and test the function, readjust
as needed.
If the brake lever adjuster is
threaded outward and the brake
still has too much slack, use the
rear brake adjuster for additional
adjustment.
4
WARNING: The
brake is capable of skidding
the tire and throwing an
unsuspecting rider. Practice
in an open area free from
obstacles until you are familiar
with the brake function. Avoid
skidding to a stop as this can
cause you to lose control or
damage the rear tire.
Repair and Maintenance
q Inflating the Tires
Tires are inflated when shipped, but they invariably lose some pressure between the point of
manufacturing and
your purchase.
WARNING: Failure
to remove the valve adapter
after inflating will cause the
inner tube and/or adapter to
be severed by the rear drive
sprocket.
E150 / E200 / E300 Rear Tire
Note: If you lose the adapter,
a valve stem extender can be
purchased at almost any auto
parts store.
1 Use the special valve
extender/adapter supplied.
The valve adapter is located
in the bag with the owners
manual supplied at the time
of purchase.
2 Align the access hole in
3 Remove valve adapter
the drive sprocket with the
tire valve. Thread the adapter
completely onto the valve and
attach the pump. Inflate to
the PSI indicated on the tire
sidewall.
immediately after inflating.
E150 / E200 / E300 Front Tire and E100 Tires
1 Using a bicycle style tire
pump equipped for a Schradertype valve, inflate the front
tire to the PSI indicated on the
sidewall of the tire.
5
Note: The pressurized air
supplies found at gasoline
stations are designed to inflate
high-volume automobile tires.
If you decide to use such an air
supply to inflate your electric
scooter tires, first make sure
the pressure gauge is working,
then use very short bursts to
inflate to the correct PSI. If you
inadvertently over-inflate the
tire, release the excess pressure
immediately.
Repair and Maintenance
q Adjusting the Chain
Tools required: 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches.
Note: This system of adjusters
is common to motorcycles and
BMX bicycles. If you are not
familiar with it or do not feel
comfortable performing the adjustment, consult an authorized
Razor service center or a qualified BMX bike or motorcycle
mechanic.
1 Using two 17mm wrenches,
loosen the rear axle bolts by
turning the wrenches counter
clockwise.
2 Using two 8mm wrenches,
3 Using a 10mm wrench,
loosen the brake housing anchor
which is located in the long slot
on the left side of the rear fork.
tighten the tension adjusters on
the axle 1/8 to 1/4 turn to finetune the chain tension. Both
adjusters must be tightened the
exact same amount to maintain
wheel alignment.
4 Once the tension is correct,
tighten the axle and brake anchor bolt. Test run the scooter.
Readjust as needed.
6
The chain should be “just taut”
– in other words snug, but not
piano-wire tight. The tension
should be similar to the fan
chain on an automobile. BE
CAREFUL NOT TO ADJUST TOO
TIGHT. The tensioning system
can easily impart too much tension and snap the chain or bend
the motor shaft. Adjust 1/8 to
1/4 turn at a time and check the
tension each time.
Repair and Maintenance
q Chain and Rear Tire Replacement
Tools required: Phillips screwdriver, 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches.
1 With a Phillips screwdriver,
2 With a 10mm wrench,
3 With two 8mm wrenches,
4 With a 10mm wrench, loosen
5 With two 17mm wrenches,
6 Pull the wheel out. Note the
7 Install new chain or wheel by
8 To hook up the brake housing
9 Install the brake spring and
loosen the two screws and
remove the chain guard.
both axle adjusters an equal
amount, about five turns.
maneuvering the chain onto the
sprocket and slipping the axle
into the slots on the frame.
loosen the brake cable anchor
and disconnect the cable.
loosen brake housing anchor
and disconnect. Keep the spacer
and washers together.
loosen the axle. Push the wheel
forward in the slots to loosen
the chain.
arrangement of the hardware
sequence. The spacer order is
small, medium and large, with
the small spacer between the
brake and frame, the medium
between the brake and wheel
and the long between the wheel
and frame.
anchor, align the cable guide
adjuster and install the spacer
and bolt. Do not tighten until
final step.
thread the cable wire into the
cable anchor. Thread the cable
to its original position and
tighten securely.
7
Repair and Maintenance
10 Install the axle adjusters
and axle nuts. Tighten until they
just barely hold the hardware
in place.
11 Tighten both axle adjust-
12 Tighten the brake housing
ers the same number of turns
to fine-tune the tension on the
chain and to approximately
maintain the centering of the
wheel.
anchor securely. Test ride and
check. Readjust as needed.
13 Replace the chain guard.
8
Repair and Maintenance
q Front Tire Replacement
Tools required: 10mm wrench, two (2) 17mm wrenches and a flathead screwdriver.
1 (E100 only, other
models go to Step 2)
Loosen the brake pad bolt and
remove one brake pad.
2 Using two 17mm wrenches,
3 Remove wheel and replace
loosen the front axle bolts by
turning the wrenches counter
clockwise.
tire. To reinstall wheel, reverse
these steps. Helpful hint: You
may need to use a flathead
screwdriver to center the axil
and the bolts.
9
Repair and Maintenance
q Battery Care and Disposal
Do not store the battery in temperatures above 75° or below -10° F.
CONTAINS SEALED LEAD BATTERY. BATTERY MUST BE RECYCLED.
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in
an environmentally sound manner. Do not dispose of a lead-acid battery in a fire. The battery may explode
or leak. Do not dispose of a lead-acid battery in your regular household trash. The incineration, land filling
or mixing of sealed lead-acid batteries with household trash is prohibited by law in most areas. Return
exhausted batteries to a federal or state approved lead-acid battery recycler or a local seller of automotive
batteries. If you live in Florida or Minnesota, it is prohibited by law to throw away lead-acid batteries in the
municipal waste stream.
q Charger
The transformer/charger supplied with the scooter should be regularly examined for damage to the cord,
plug, enclosure and other parts, and, in the event of such damage, the scooter must not be charged until it
has been repaired
or replaced.
Use ONLY with the recommended charger.
q Replacement Parts
The most frequently requested replacement parts (wheels, tires, tubes, batteries and chargers) are
available for purchase at some Razor retail partners or online at www.razorama.com. For other parts
contact an authorized Razor repair center.
q Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Send e-mail to customerservice@razorusa.com or call 866-467-2967 for the center nearest you.
10
WARNING: If a
battery leak develops, avoid
contact with the leaking acid
and place the damaged battery
in a plastic bag. Refer to the
disposal instructions at left. If
acid comes into contact with
skin or eyes, flush with cool
water for at least 15 minutes
and contact a physician.
Troubleshooting Guide
Problem
Scooter does not run
Possible Cause
Solution
Undercharged battery
Charge the battery. A new battery should have been charged for at
least 12 hours before using the scooter for the first time and up to 8
hours after each subsequent use.
Check all connectors. Make sure the charger connector is tightly
plugged into the charging port, and that the charger is plugged into
the wall.
Scooter was running but
suddenly stopped
Charger is not working
Make sure power flow to the wall outlet is on.
Loose wires or connectors
You may check to see if your charger is working by using a volt meter
or asking your local Razor authorized service center to test your
charger for you.
E100 only - Scooter must be
traveling 3mph before motor will
engage.
Kick start to 3mph then twist the throttle to start motor.
Tripped circuit breaker
Check all wires and connectors to make sure they are tight.
The circuit breaker (next to on/off switch) will automatically shut off
the power if the motor is overloaded.
An excessive overload, such as too heavy a rider or too steep a hill,
could cause the motor to overheat. If the scooter suddenly stops
running, wait a few seconds and then push the breaker to reset the
circuit. Correct the conditions that caused the breaker to trip and
avoid repeatedly tripping the breaker.
Short run time (less than
30 minutes per charge)
Undercharged battery
Charge the battery. A new battery should have been charged for at
least 12 hours before using the scooter for the first time and up to 8
hours after each subsequent use.
Check all wires and connectors. Make sure the battery connector is
tightly plugged into the charger connector, and that the charger is
plugged into the wall.
Scooter runs sluggishly
Battery is old and will not accept
full charge
Make sure power flow to the wall outlet is on.
Brakes are not adjusted properly
Refer to adjusting the brakes instructions on page 4.
Driving conditions are too stressful
Use only on solid, flat, clean and dry surfaces such as pavement or
level ground.
Tires are not properly inflated
The tires are inflated when shipped, but they invariably will lose
some pressure between the point of manufacturing and your
purchase. Refer to instructions on page 5 of this manual to properly
inflate tires.
Scooter is overloaded
Make sure you do not overload the scooter by allowing more than
one rider at a time, exceeding the E100 120 lb. or E200 and E300 220
lb. maximum weight limit, going up a hill or towing objects behind
the scooter. If the scooter is overloaded, the circuit breaker may trip
and shut off power to the motor. Correct the driving conditions that
caused the overload, wait a few seconds, and then push the breaker
to reset the circuit. Avoid repeatedly tripping the circuit breaker.
Brake dragging
E100: Use your fingers to twist the adjuster in either direction until
wheel is centered between pads.
Even with proper care, a rechargeable battery does not last forever.
Average battery life is 1 to 2 years depending on scooter use and
conditions. Replace only with a Razor replacement battery.
E200/E300: Adjust brake at lever (page 4) to allow wheel to spin
without brake contact.
11
Troubleshooting Guide
Problem
Possible Cause
Solution
Sometimes the scooter
doesn’t run, but other
times it does
Brakes are not adjusted properly
Refer to adjusting the brakes instructions on page 4.
Loose wires or connectors
Check all wires around the motors and all connectors to make sure
they are tight.
Charger gets warm
during use
Motor or electrical switch
damage
Contact your local Razor authorized service center for diagnosis and
repair.
Scooter does not stop
when applying the brake
Normal response to charger use
No action required. This is normal for some chargers and is no cause
for concern. If your charger does not get warm during use, it does not
mean that it is not working properly.
Scooter makes loud
noises or grinding
sounds
Brakes are not adjusted properly
Refer to adjusting the brakes instructions on page 4.
Chain is too dry
Apply a lubricant such as 3 in 1 or Tri-Flow to the chain.
Brake rotor is dragging on brake
pads
Use your fingers to twist the caliper adjuster in either direction until
rotor is centered between pads.
TM
TM
Need Help? Visit our web site for updates and a list of authorized service centers at www.razor.com
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
12
E100 parts
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
01 Handlebar grip (right/left)
10 Front caliper brake
02 Single speed twist grip throttle
11 Battery tray
02-1 Sleeve
12 On/ Off switch
03 Handlebar stem/ T-bar
13 Charger port w/ wires
03-1 Black folding knob
14 Reset button w/ wire
03-2 6mm stem bolt
15 Control module
03-3 Washer
16 Battery (2- 12V/ 4.5Ah)
03-4 Wedge
17 Kickstand
04 Brake lever assemble complete
18 Motor (24V / 100W)
05 Headset (upper)
19 Rear wheel complete
06 Frame
20 Chain
07 Headset (lower)
20 Chain guard
08 Front fork
20 Deck plate w/ grip take set
09 Front wheel complete
13
E100 parts
14
E150 parts
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
01 Handlebar grip (right/left)
09 Front wheel complete
01-1 Valve stem extender/ inflator
10 Battery tray
01-2 Handlebar end cap/ Extender holder
11 On/ Off switch
02 Brake lever assemble complete
12 Reset button w/ wire
03 Handlebar stem/ T-bar
13 Charger port w/ wires
03-1 Black folding knob
14 Control module
03-2 6mm stem bolt
15 Battery (2- 12V/ 4.5Ah)
03-3 Washer
16 Motor (24V/ 100W)
03-4 Wedge
17 Kickstand
04 Speed controller w/ LEDs
18 Rear wheel complete
04-1 Sleeve
19 Chain
05 Headset (upper)
20 Chain guard
06 Frame
21 Deck, Upper plate
07 Headset (lower)
22 Main deck board
08 Front fork
15
E150 parts
16
E200 parts
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
01 Handlebar Grip (right/left)
11 Front wheel complete
01-1 Valve stem extender/ inflator
12 Battery tray
01-2 Handlebar end cap, Extender holder
13 Reset button w/ wire
02 Speed controller w/ LEDs
14 On/ Off switch
02-1 Sleeve
15 Charger port w/ wires
03 T-bar
16 Control module
04 Brake lever assemble complete
17 Motor (24V/ 200W)
05 Quick release
18 Kickstand
06 Extension tube/ Folding system
19 Battery (2- 12V/ 7Ah)
06-1 Black folding knob
20 Rear wheel complete
06-2 6mm stem bolt
21 Chain
06-3 Washer
22 Chain guard
06-4 Wedge
23 Rear fender
07 Headset (upper)
24 Deck
08 Frame
25 Seat post
09 Headset (lower)
26 Seat
10 Fork front
17
E200 parts
Only used on E200S
18
E300 parts
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
01 Handlebar grips (right/left)
09 Front wheel complete
01-1 Valve stem extender/ inflator
10 Battery tray
01-2 Handlebar end cap, Extender holder
11 Reset button
02 Single speed twist grip throttle
12 On/ off switch
02-1 Sleeve
13 Charger port w/ wires
03 Handlebar Stem/ T-bar
14 Control module
03-1 Black folding knob
15 Battery (2- 12V/ 7Ah)
03-2 6mm stem bolt
16 Motor (24V/ 250W)
03-3 Washer
17 Kickstand
03-4 Wedge
18 Rear wheel complete
04 Brake lever assemble complete
19 Chain
05 Headset (upper)
20 Chain guard
06 Frame
21 Deck plate w/ grip tape
07 Headset (lower)
22 Seat post
08 Front fork
23 Seat
19
E300 parts
Only used on E300S
20
SB 1918 (CALIFORNIA) DECLARATION
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD
CONTACT YOUR INSURANCE COMPANY OR AGENT.
20
Safety reminders
PRE-RIDE CHECKLIST
q
Loose Parts
q
Tire Inflation
q
Brake
q
Safety Gear
q
Frame, Fork and Handlebars
Check and secure all fasteners before every
ride. Make sure steering stem clamp bolts are
locked properly in place. There should not be any
unusual rattles or sounds from loose parts or
broken components. If you are not sure, ask an
experienced mechanic to check.
Check the brakes for proper function. When
you squeeze the lever, the brake should provide
positive braking action. When you apply the
brake with the speed control on, the brake cutoff switch will stop the motor.
Periodically inspect the tires for excess wear,
and regularly check the tire pressure and reinflate as necessary. If you get a flat tire, the
inner tube can be patched or a new tube can be
purchased from Razor or an authorized repair
center.
Always wear proper protective equipment such
as an approved safety helmet, elbow pads and
kneepads. Always wear athletic shoes (lace-up
shoes with rubber soles), never drive barefooted
or in sandals, and keep shoelaces tied and out of
the way of the wheels, motor and drive system.
Check for cracks or broken connections.
Although broken frames are rare, it is possible
for an aggressive driver to bash into a curb or
wall and wreck and bend or break a frame. Get
in the habit of inspecting yours regularly.
DO NOT RETURN TO STORE
Do not use this vehicle for the first time until you have inflated the
tires to the correct PSI and charged the battery for at least 12 hours.
Failure to follow these instructions may damage
your vehicle and void your warranty.
Warranty
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited
Warranty does not cover normal wear and tear, tires, tubes or
cables, or any damage, failure or loss caused by improper assembly,
maintenance, or storage or use of the Razor electric chopper.
This Limited Warranty will be void if the product is ever
• used in a manner other than for recreation or transportation
• modified in any way;
• rented.
The manufacturer is not liable for incidental or consequential loss or
damage due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
For your records, save your original sales receipt with this manual and
write the serial number below.
__________________________________________
Item Numbers
E100
13100E-BL
E125
13125E-BK Black
13111110 Red
E150 13111612
E200
13200E-SL
E200S
13201S-SL
E225S
13112850
E300
13300E-SL
E300S
13301S-SL
E325S
13116390
Need Help? Visit our web site for updates and a list of authorized service centers at www.razor.com
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
Community Design No. 130919-0001
U.S. Design Patent D497,397 S
Printed in China for:
Razor USA LLC
PO Box 3610
Cerritos, CA 90703
© Copyright 2007 Razor USA. All rights reserved.
12102007
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1.1-111 About : fdf3fb81-02c5-11db-b7e0-b9954f0520b1 Create Date : 2007:12:10 16:04:20-08:00 Metadata Date : 2007:12:10 16:05:11-08:00 Modify Date : 2007:12:10 16:05:11-08:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 8363 bytes, use -b option to extract) Document ID : adobe:docid:indd:fdf3fb7f-02c5-11db-b7e0-b9954f0520b1 Instance ID : uuid:bd9a5673-a77c-11dc-be23-0017f2077756 Rendition Class : proof:pdf Derived From Instance ID : fdf3fb7e-02c5-11db-b7e0-b9954f0520b1 Derived From Document ID : adobe:docid:indd:30a10a93-f93e-11da-919b-cd1b8dcdfebf Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Document ID : adobe:docid:photoshop:353af0be-9aea-11da-b050-bae6bcf9491b, adobe:docid:photoshop:7690a444-f962-11da-9ac5-d8391f5a4589, adobe:docid:photoshop:a33210c2-30e1-11da-acff-c433894b97ce, adobe:docid:photoshop:77689d28-a304-11d9-9f4c-b505d103b7f2, adobe:docid:photoshop:905c1418-caa4-11d8-8b79-ba0295c04536, adobe:docid:photoshop:c3a1c1bb-f2b8-11d8-a540-e7dae512e95a, adobe:docid:photoshop:e467555f-f2b7-11d8-a540-e7dae512e95a, adobe:docid:photoshop:aa49e6bc-a303-11d9-9f4c-b505d103b7f2, adobe:docid:photoshop:669ff6fe-f945-11da-9ac5-d8391f5a4589, uuid:86b382c3-a249-11d9-8033-000a95c8b6f6, uuid:277CDBB5C2A8DC11A09A9209E6F12B74, uuid:63227041AFA5DC11A25CC9DC1531FE08, uuid:3900CB2FBFA8DC11A09A9209E6F12B74, uuid:3500CB2FBFA8DC11A09A9209E6F12B74 Manifest Reference Instance ID : uuid:287CDBB5C2A8DC11A09A9209E6F12B74, uuid:64227041AFA5DC11A25CC9DC1531FE08, uuid:3A00CB2FBFA8DC11A09A9209E6F12B74, uuid:3600CB2FBFA8DC11A09A9209E6F12B74 Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 24 Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools