Remington Power Tools 494 Users Manual 101437 01

494 to the manual a9995596-c84f-30e4-89c7-76ac3154d891

2015-02-06

: Remington-Power-Tools Remington-Power-Tools-494-Users-Manual-523143 remington-power-tools-494-users-manual-523143 remington-power-tools pdf

Open the PDF directly: View PDF PDF.
Page Count: 24

®
A
N
I
N
D
E
P
E
N
D
E
N
T
L
A
B
O
R
A
T
O
R
Y
T
E
S
T
I
N
G
F
O
R
P
U
B
L
I
C
S
A
F
E
T
Y
G 028
Read this manual and all labels carefully before
operating your powder actuated tool. This manual
should always accompany the tool and be transferred
with it upon change of ownership.
REMINGTON®
POWDER ACTUATED TOOL
MANUFACTURERS´ INSTITUTE INC.
™
G 029
Model 494
Powder Actuated
Fastening Tool
Operating
Instructions
IMPORTANT:
482-1
2
101437
Maximum 3" (76 mm)
* Not provided with tool
Power Load*
Trigger
Muzzle/Guide
Recommended
Approved
Goggles*
Power Fastener*
Spall Shield
Barrel Assembly
REMINGTON
Model 494 Powder Actuated Fastening Tool
The Remington Model 494 Powder Actuated Fastening Tool is designed for use
with Remington 22 caliber Type A crimped loads and Remington Power Fasteners.
Remington power fasteners are manufactured from special steel and heat treated
to produce a very hard yet ductile fastener.
INDEX
Warning: Safety Precautions................................................................................. 3-11
Why A Fastener Holds ............................................................................................. 12
Selecting Fasteners and Power Loads .................................................................... 13
Operation ................................................................................................................. 14
Maintenance............................................................................................................. 16
Troubleshooting ....................................................................................................... 16
Parts Centrals .......................................................................................................... 17
Parts List .................................................................................................................. 18
Accessories .............................................................................................................. 19
Tool Disassembly ..................................................................................................... 19
Tool Assembly.......................................................................................................... 20
Buffer and Piston Replacement ............................................................................... 21
Application Chart ...................................................................................................... 22
Warranty.................................................................................................... Back Cover
3
101437
Warning: Safety Precautions
The following pages contain detailed warnings, cautions, and rules of safe operation.
Read carefully and become familiar before operating to avoid serious injury. We
expressly disclaim any liability for any injury to persons or damage to property which result
from your failure to take the precautions contained in this manual.
!
WARNINGICON G001
WARNING: This tool is designed only for use by qualified operators. Qualification
is obtained through a thorough understanding of the Safety Warnings and operating
instructions as defined in this operating manual. NOTE: The labor regulations of many
states require that the operator of this tool on a job site be thoroughly trained and certified
for competence prior to operating this tool. For certification procedures, call: DESA
Technical Services Department, 1-800-626-2237.
!
WARNING ICON G 001
2. ALWAYS inspect to make sure the tool is working properly. If the tool does not work properly,
remove from service and tag DEFECTIVE. DO NOT use the tool again until it has been properly
repaired.
BEFORE USING
1. ALWAYS handle the tool as if it were loaded. Before starting work, check that the tool is
unloaded and the muzzle is clear. NEVER load a tool unless it is going to be used.
DEFECTIVE
G 018
3. Operators and bystanders must ALWAYS wear goggles and ear protection which meet or
exceed ANSI standards.
4
101437
482-12
G 018
G 018
G 018
Safety Precautions
5. ALWAYS make sure the work area is clean from loose material and debris.
2. NEVER place your finger on the trigger until the tool’s muzzle is against the work surface.
1. NEVER place your hand over the muzzle. Accidental discharge can cause serious injury.
HANDLING THE TOOL
482-9
4. ALWAYS clear the work area on all sides and post appropriate warning signs on job sites.
POWDER
ACTUATED
TOOLS
IN USE
WARNING
482-10
!
5
101437
482-19
482-24
G 018
G 018
G 018
G 018
Safety Precautions
3. ALWAYS store UNLOADED powder actuated tool and power loads in a locked container. Keep
power loads of different power levels in separate containers.
4.NEVER carry or pass a loaded powder actuated tool. NEVER point a powder actuated tool at
anyone.
6. ALWAYS take precaution to maintain your balance while operating a powder actuated tool.
5. If the tool is dropped, inspect for damage and repair it before continuing to work. NEVER use
a damaged tool.
POWDER
LOADS
POWD
LOAD
482-23
6
101437
TOO HARD
Point
flattens
482-29
?
?
?
482-25
TOO BRITTLE
Surface
shatters
482-30
TOO SOFT
Sinks in
with
average
hammer
blow
482-28
G 018
G 018G 018
G 018
Safety Precautions
1. ALWAYS know the thickness and type of base material into which you are fastening. NEVER
GUESS. Test the base material by using the Center Punch Test. The Center Punch Test is
performed by using a hammer to test drive the particular power fastener to be used into the
material. If the point penetrates easily, the material is too soft. If the point becomes blunt, the
material is too hard. If the material fractures, cracks or shatters, the material is too brittle. Test
fastenings can be made if the material shows a clear fastener impression and the fastener point
is not blunted. ALWAYS start with the lowest power load (Gray-Level 1) and proceeding with
the order shown in the lower right-hand figure above. Always wear approved goggles.
KNOW YOUR FASTENING BASE MATERIAL
?
?
?
?
482-26
7. An operator taking medication should take extra precautions while handling the tool. NEVER
drink alcoholic beverages or take medications which impair your vision, balance or judgement
before using a powder actuated tool.
CENTER
PUNCH TEST
482-27
Start
1
GRAY
3
GREEN 4
YELLOW
2
BROWN
482-31
7
101437
CAST IRON GLASS
TILE BRICK
482-33
Safety Precautions
3. NEVER make fastenings in spalled or cracked areas.
2.NEVER attempt to drive power fasteners into very hard or brittle materials including, but not
limited to cast iron, glass, tile, stone, brick, or hardened steel. Materials of this type tend to
shatter and create hazard from flying particles.
4. NEVER drive power fasteners into thin or easily penetrated materials unless it is backed by
concrete or steel. When in doubt, such as when base material is concealed, conduct a Center
Punch Test (See page 6). Check continually to avoid fastening into unsuitable material,
especially in older buildings.
5. DO NOT fasten through or within 1/2" of predrilled or pre-punched holes.
G 018
G 018
G 018
G 018
G 018
8
101437
TOO THIN
WELD
482-40
G 018
G 018
Safety Precautions
7. DO NOT drive power fasteners into steel base material less then 3/16" thick, within 2" of a weld,
within 1/2" of the edge or within 1" of another power fastener.
6. DO NOT drive power fasteners into concrete less than three times as thick as the intended
fastener penetration, within 3" of the edge, within 3" of another power fastener or within 3" of
a failed power fastener.
3"
3X
1X
482-38
8. When fastening into masonry walls, always drive into horizontal mortar joints, never into vertical
mortar joints. BE CAREFUL. A poorly laid joint may permit too much penetration, and/or
unsatisfactory holding power.
3/16" MIN
1/2" 1"
482-41
3" 3"
3"
482-39
1. ALWAYS hold tool perpendicular to work surface.
OPERATING THE TOOL
9
101437
POWER
LOADS
POWER
LOADS
482-49
GASOLINE
GAS
OLINE
482-50
G 018
G 018
G 018
G 018
Safety Precautions
2. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds.
Release the trigger and remove pressure on the tool while holding the muzzle against the
work surface. Again press the tool firmly against the work surface and pull the trigger. If the
tool still fails to fire, hold the tool firmly against the work surface for another 30 seconds before
unloading and carefully discarding the misfired power load into water or oil.
POWER LOADS AND FASTENERS
1. NEVER leave unfired power loads on floors or work surfaces.
4. NEVER use a powder actuated tool in an explosive or flammable atmosphere or when non-
sparking tools are required.
3. ALWAYS use the spall shield when driving directly into concrete or steel. Always wear
approved goggles.
WATER
482-46
G 018
10
101437
482-58
YELLOW?
BROWN?
GREEN?
GRAY?
G 018
2. Remington power loads are available in four power levels with gray (1) being the lowest power
level and yellow (4) being the highest power level. Always start with the lowest power level
(gray-level 1) and increase until a proper fastening is made (see page 13
Selecting Fasteners
and Loads).
Start
1
GRAY
3
GREEN 4
YELLOW
2
BROWN
482-31
Safety Precautions
5. A color blind person must take extra precautions to prevent the chance of mixing the power
loads of various levels.
1
2
3
456789
10
11
12
1
22
L
E
K
C
I
N
B
R
A
S
S
482-53
C
A
L
I
B
E
R
NOTE:
Failure to start with
the lowest power
level can result in
overdrive condition
and will result in
damage to tool
(See page 13).
3. NEVER use power loads in firearms.
POWDER
LOADS
ONLY
482-57
POWER
LOADS
ONLY
4. NEVER carry fasteners or other hard objects in the same pocket or container with power loads.
POWER
LOADS
POWER
LOADS
G 018 G 018
11
101437
482-59
G 018
Safety Precautions
6. Power fasteners are a permanently installed fixture. An act of demolition is required for their
removal. Appropriate safety precautions must be taken.
Plastic Flute
Shank
Head
482-60
7. NEVER use common nails or other materials as fasteners. Remington Power Fasteners are
manufactured from special steel and heat treated to produce a very hard yet ductile fastener.
G 018
8. NEVER pry a power load out of the tool. Prying can discharge the load causing serious injury
(see
Troubleshooting Guide
, page 16).
9. ALWAYS insert the power fastener first, then the power load. If work is interrupted for any
reason, ALWAYS remove the power load before removing the power fastener (see page 15,
item 7).
12
101437
WHY A POWER FASTENER HOLDS
IN CONCRETE
The compression bond of the concrete to the power fastener
accounts for the majority of the holding power. The fastener dis-
places the concrete which tries to return to its original form causing
a squeezing effect.
Maximum holding power is achieved when the depth of penetration
produces a bond on the power fastener equal to the strength of the
concrete. As a general rule, penetration should be approximately 1"
to 1 1/4" into the base concrete. Make sure the concrete is at least
three times as thick as the intended fastener penetration. NEVER
have the power fastener point protrude through the concrete.
NOTE: Concrete needs to cure for 28 days before maximum
fastening holding power will be achieved.
WHY A POWER FASTENER HOLDS IN STEEL
Holding power in steel depends on the elasticity of the steel. The
steel pushes back on the shank of the power fastener.
Drop a marble into water; the water parts, the marble continues
down, the water closes back. This is similar to the reaction when a
power fastener penetrates steel.
In steel, the point of the power fastener must penetrate completely
through for highest holding power. If the fastener does not penetrate,
the spring action of the steel pushes back on the point and tends to
force the fastener out.
Recommended applications are between 3/16-3/8" steel.
NOTE: When fastening in steel be sure the point goes through the
steel.
482-64
Why A Power Fastener Holds
482-65
13
101437
FASTENING INTO CONCRETE
The proper power fastener length can be determined by adding the
thickness of the material to be fastened and the amount of fastener
that will actually penetrate the concrete. The concrete must be three
times as thick as the intended fastener penetration. In most cases,
penetration should be approximately 1" to 1 1/4" into the base
concrete material.
482-85
Wood or Non-Metals
To Concrete
POWER LOADS
Always start with the lowest power level (gray-level 1). If the first test
fastener does not penetrate to the desired depth, move to the next
highest power level (brown-level 2). Increase until a proper fastening
is made.
IMPORTANT: Damage to the tool will result if the above instructions
are not followed (see illustrations to right and lower right).
Piston Extended
Out of Muzzle
OVERDRIVEN POWER FASTENERS
AND PISTON
An overdriven power fastener results when too strong of a power load
is used causing the piston to extend past the muzzle. Move to the next
lightest power load. Repeated overdrive will damage your tool. By
avoiding overdrive, you can extend the life of your tool considerably
and avoid costly repairs.
NOTE: NEVER fire the tool without a power fastener. This can
damage the tool and/or cause possible injury to the operator.
482-79
Wood or Non-Metals
To Steel
482-66
RIGHT
Flush With Surface
Selecting Power Fasteners
and Power Loads
FASTENING INTO STEEL
The proper fastener length can be determined by adding the thickness
of the material to be fastened and the thickness of the steel. The point
of the power fastener must go completely through the steel.
OVERDRIVE
G 018
14
101437
Operation
1. Grasp muzzle and slide barrel forward rapidly until it stops. This sets piston into firing position
and opens the chamber.
4. Push barrel into housing to the closed position.
3. Select the proper Remington Power Load and insert into the chamber until it stops (see
Application Chart
on page 23).
482-70
2. Insert power fastener into muzzle of tool, head end first. Push the fastener until point is even
with end of tool. ALWAYS load the fastener first, then the power load.
482-71
NOTE:
Failure to start with
the lowest power
level can result in
overdrive condition
and will result in
damage to tool
(see page 13).
482-71
482-72
15
101437
WATER
Operation
5. Place the muzzle of tool perpendicular to work surface without tilting the tool. Push tool against
work surface until sliding action of barrel stops.
8. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds.
Release the trigger and remove pressure on the tool while holding the muzzle against the
work surface. Again press the tool firmly against the work surface and pull the trigger. If the
tool still fails to fire, hold the tool firmly against the work surface for another 30 seconds before
unloading and carefully discarding the misfired power load into water or oil.
7. After fastening is made, slide barrel forward rapidly. This motion ejects the spent power load
and resets the piston for the next fastening. Make sure spent load has ejected from tool.
6. Squeeze trigger to set power fastener. Be sure to keep pressure on tool during this operation.
WATER
482-46
16
101437
Tang
Tang Spring
Tang Cap
Buffer
Muzzle Cap Piston
Barrel Receiver
Maintenance
Troubleshooting Guide
PROBLEM
Piston rod hangs out of muzzle
cap.
Overdriving of power fastener.
Piston jammed.
Expended power load will not
extract.
Reduction or loss of power.
REMEDY
Remove barrel assembly.
Follow instructions for piston
change. Replace all damaged
or missing parts.
Replace piston.
Change either to next lower
power load, or use next longer
fastener length.
Remove barrel assembly.
Follow instructions for buffer
replacement (page 21). Replace
other parts if damaged.
Clean receiver chamber. If
power loads will not chamber
with a slip-fit or extraction
difficulties continue, take tool to
your distributor for repair.
Barrel must be opened fully to
the full extended position to
properly position piston.
Remove piston. Replace piston
ring.
Replace piston.
POSSIBLE CAUSE
Piston not properly assembled
in relation to tang.
Broken piston.
Excessive power.
Overdriving of power fastener
(see above).
Buffer binding on piston in
muzzle cap.
Dirty or damaged receiver
chamber.
Piston not returning to full rear
position.
Worn piston ring.
Broken piston.
IMPORTANT:
Clean your tool after each day’s use. The parts shown in the illustration below should be cleaned
daily. Clean metal parts with accessory wire brushes. Apply penetrating lubricant sparingly and wipe
dry.
17
101437
Troubleshooting Guide (cont.)
PROBLEM
Tool does not completely
depress.
Tool does not fire.
Opening and closing of barrel
or pushing down of the tool,
etc. is not smooth but is rough
or binds.
REMEDY
Remove breech and check all
parts for correct fit assembly.
See data listed under
Tool
Does Not Completely Depress,
above.
Check firing pin indentation on
cartridge. Clean breech, breech
face, and firing pin.
Inspect and clean complete tool
(see
Maintenance
on page 16).
Replace worn or damaged
parts.
POSSIBLE CAUSE
Misassembled or damaged
breech and firing pin parts.
Failure of tool to depress
completely.
Dirt buildup on breech not
allowing proper penetration of
firing pin.
Lack of proper cleaning.
Parts Centrals
Contact authorized dealers of this product. If they can’t supply original replacement part(s),
either contact your nearest Parts Central (see below) or call DESA International’s Parts
Department at 1-800-972-7879.
When calling DESA International, have ready
•model number of your tool • replacement part number
RAILWAY DISTRIBUTORS
264 Railway Avenue
Campbell, CA 95008
408-866-9266
Guy Bothelho
BALTIMORE ELECTRIC
1348 Dixwell Avenue
Hamden, CT 06574
1-800-397-7553
203-248-7553
Parts Department
ALL TOOL & FASTENER
7830 N.W. 72nd Avenue
Miami, FL 33166
305-888-6909
Parts Department
PRECISION TOOL
431 Commerce Park Drive
Suite 106
Marietta, GA 30060
404-421-0688
Bob Young
PORTABLE HEATER PARTS
342 No. County Road 400 East
Valparaiso, IN 46383
219-462-7441
1-800-362-6951
F B D
601 Hope Street
Bowling Green, KY 42101
502-796-8406
1-800-654-8534
MASTER SERVICE CENTER
1184 Wilson NW
Grand Rapids, MI 49504
US 1-800-446-1446
616-791-4760
Mike Fowler
MANZO ASSOCIATES
1645 Bustleton Pike
Feasterville, PA 19053
215-364-0480
Parts Department
21st CENTURY
RD 2, Box 165
Perkasie, PA 18944
215-795-0400
1-800-325-4828
Parts Department
BLUEBONNET TOOL
10490 Shady Trail
Suite 104
Dallas, TX 75220
214-358-2363
Ken Perry
CLARK SUPPLY
9435 Summerbell
Houston, TX 77074
713-771-0404
Parts Department
18
101437
Parts List – Model 494
KEY PART
NO. NO. DESCRIPTION QTY.
1101123-01 Screw, 1/4"-20 x 1.25 2
2 101122-01 Washer 2
3101128-01 Handle & Trigger Assembly 1
4056217 Firing Pin Spring 1
5075370 Firing Pin 1
6101148-01 Breech Spring 1
7100858-01 Breech 1
8101124-01 Stop Pin 1
9101127-01 Barrel and Insert Assembly 1
10 101126-01 Piston and Ring Assembly 1
10A 101439-01 Piston Ring 1
11 100856-01S Receiver Assembly 1
12 100864-01 Tang 1
13 TA4083 Buffer (5 Pack) 1
14 100857-01S Muzzle Cap 1
15 101147-01 Tang Spring 1
16 100862-01 Tang Cap 1
17 056218 Sear Spring 1
18 076657 Sear 1
IMPORTANT: Do not use key numbers when ordering service parts. Always order components
by part number and description. Include model number and serial number of tool.
14
13
9
76
11
3
4
5
17
18
12
15 16
8
10 10A
1
2
19
101437
Accessories
DISASSEMBLY
1. a) Remove tang cap, tang spring, and tang.
Slide barrel assembly from receiver.
b) Remove muzzle cap from barrel by un-
screwing counterclockwise.
Barrel Assembly
Muzzle Cap Barrel
Tang
Tang Spring
Tang Cap
Receiver Receiver Screws
Firing Pin Spring
Handle and Trigger Assembly
Firing Pin
Sear Spring
Sear
2. Remove upper screws from handle and trig-
ger assembly. Slide receiver from handle
and trigger assembly. Remove firing pin and
firing pin spring. Sear and sear spring will fall
out when firing pin is removed.
3. Insert the barrel back into the receiver and
press down. This will release the stop pin.
Remove the stop pin. Remove barrel,
breech, and breech spring from receiver.
Stop Pin
Receiver
Breech Spring
Breech
Barrel
PART NO. DESCRIPTION
101320-02 Spall Shield
056415 Goggles
056485 Brush, 1/4"
056486 Brush, 5/8"
103754 Hex Wrench 3/16"
For Parts and Accessories, please contact your dealer or distributor. If they are unable to satisfy
your requirements, please contact DESA International at the locations as stated on back page.
Tool Disassembly and Assembly
!
WARNING ICON G 001
WARNING: Always unload a powder actuated tool before disassembling, replacing barrel,
cleaning, or assembling.
Piston
Barrel Slot
Buffer
Barrel
c) Insert a rod or screwdriver into barrel slot
and push piston and buffer out of barrel.
20
101437
Tool Disassembly and Assembly
WARNING: Always unload a powder actuated tool before disassembling, replacing barrel,
cleaning, or assembling.
!
WARNING ICON G 001
ASSEMBLY
1. Place buffer, small end first, in muzzle cap.
Push piston all the way into the barrel.
Screw muzzle cap into barrel.
2. Drop breech spring in receiver. Drop breech
in receiver. Line up slot in top of breech with
hole in the receiver. Use barrel to push
breech assembly up in the receiver.
Muzzle
Cap
Buffer
(Small End in Muzzle Cap)
Piston
Barrel
3. Insert stop pin through hole in receiver and
into the slot on breech. Remove barrel as-
sembly. Breech should remain in place.
Barrel Assembly
Receiver
Breech
Breech
Spring
Stop Pin in Breech Slot
Barrel Assembly
Breech Spring
Stop Pin
Receiver
Breech
Hole
4. Reinsert barrel assembly slotted side down
into receiver. Turn tool over. With barrel
touching breech, insert tang and tang spring
into hole on bottom of receiver. Make sure
tang drops into the slot in the barrel. Screw
on tang cap completely. Tang cap must
always be kept tight to ensure proper opera-
tion of tang.
Breech
Receiver
Barrel Assembly
Slot in
Barrel
Tang Cap
Tang Spring
Tang
5. Place sear spring on breech through slot in
bottom of receiver. Slide long side of sear
with hole between breech and breech
spring. Attach firing pin spring to firing pin.
Insert firing pin through hole on end of the
receiver and through hole on sear.
Sear
Sear
Spring
Firing Pin
and Spring
Receiver
Slot
6. Attach handle and trigger assembly to re-
ceiver with two screws and washers.
Receiver
Trigger and
Handle
Assembly
Washers Screws
21
101437
Buffer and Piston Replacement
!
WARNING ICON G 001
WARNING: Always unload a powder actuated tool before disassembling, replacing barrel,
cleaning, or assembling.
Breech
Receiver
Barrel Assembly
Slot in
Barrel
Tang Cap
Tang Spring
Tang
3. Reinsert barrel assembly slotted side down
into receiver. Turn tool over. With barrel
touching breech, insert tang and tang spring
into hole on bottom of receiver. Make sure
tang drops into the slot in the barrel. Screw on
tang cap completely. Tang cap must always be
kept tight to ensure proper operation of tang.
2. Place buffer, small end first, in muzzle cap.
Push new piston all the way into the barrel.
Screw muzzle cap into barrel.
TO REASSEMBLE:
IMPORTANT: Inspect piston ring and replace
if worn.
1. Install new piston ring onto piston (if required).
a) Remove old piston ring.
b) Install new ring. The piston ring consists of
three turns. Place one end into groove
and twist around piston until it is com-
pletely in groove.
IMPORTANT: This tool is equipped with a
piston buffer. The buffer stops the piston before
it makes contact with the muzzle cap. This
protects the barrel and muzzle cap. Inspect and
replace the buffer on a regular basis.
Worn Piston
Buffer
New Piston
Buffer
TO REPLACE BUFFER AND PISTON:
1. a) Remove tang cap, tang spring, and tang.
Slide barrel assembly from receiver.
b) Remove muzzle cap from barrel by un-
screwing counterclockwise.
Barrel Assembly
Muzzle Cap Barrel
Tang
Tang Spring
Tang Cap
Receiver
Piston
Barrel
Chamber
Piston Buffer
Barrel
c) Insert a rod or screwdriver into barrel
chamber and push piston and buffer out of
barrel.
Piston
Piston Ring
Barrel
Piston
Muzzle Cap
Piston Buffer
(Small End in Muzzle Cap)
22
101437
482-81a
Two by fours
Furring strips
Metal electrical
junction boxes
Conduit clips
Shelf brackets
1/4" Plywood or
pegboard
For fastening this
Power load and power fastener application information.
Application Chart
power load
color
power fastener
length
to this
Green
Brown
Yellow
1"
1"
1"
Concrete
Cement block
Steel (3/16" to 3/8" thick)
Concrete
Cement block
Steel (3/16" to 3/8" thick)
Green
Green
Yellow
1 1/4"
1 1/4"
1 1/4"
Power load listings are recommendations only. If you are in doubt, try a test fastening using the
next lightest power load.
5/8"
WARNING ICON G 001
CAUTION
Do not use any load other than the 22 caliber neck-down crimped load. Other
types of loads will cause load-ejection problems.
IMPORTANT
This tool is designed to use 22 caliber neck-down crimped loads, power levels 1 (gray) through 4
(yellow).
G 018
Straight Wadded
Power Load
Neck-Down
Crimped Power Load
Green
Green
Yellow
2 1/2"
2 1/2"
2"
Concrete
Cement block
Steel (3/16" to 3/8" thick)
Concrete
Cement block
Steel (3/16" to 3/8" thick)
1 1/2"
1 1/2"
2"
Green
Green
Yellow
Concrete
Cement block
Steel (3/16" to 3/8" thick)
Green
Brown
Yellow
1"
1"
1"
Green
Brown
1"
1"
Concrete
Cement block
23
101437
Application Chart
IMPORTANT
•If power fastener goes below the top surface of the board, use penetrating control disc (* see
illustration below).
•Always wear approved eye and ear protection.
482-90
*Use power fastener with penetration control disc, part number 015549.
22 CALIBER
Type A Crimp
Loads for
powder
actuated tools
Load Color Code
Stock Level Load Case
Number Number Strength Body Head
A22C1 1 light brass Gray
A22C2 2 medium brass Brown
A22C3 3 heavy brass Green
A22C4 4 extra heavy brass Yellow
Limited Warranty Agreement
DESA International warrants the Remington Model 494 Powder Actuated Fastening Tool against
defects in materials and workmanship for a period of one (1) year from the date of purchase.
If within one (1) year from the purchase date this Powder Actuated Tool fails due to a defect in
material or workmanship, DESA will repair or replace the tool at DESA’s option. To obtain service
under this warranty, contact DESA at the number/address listed below. You must have the Serial
Number, Model Number, date of purchase and indicate the type of problem being experienced.
DESA will send replacement part(s), repair or replace the tool at DESA’s option. However, this
warranty does not cover failures caused by misusing or abusing the product (for proper use of this
product, read and understand the operating instructions in this owners manual). Repairs made
because of misuse, abuse, negligence or accident will be charged for at regular repair prices.
This express and limited warranty is the only warranty on this product, and to the full extent permitted
by law there are no other warranties, express or implied, including warranties of merchantability and/
or fitness for a particular purpose which extend beyond the terms of this express and limited warranty.
To the full extent permitted by law, the liability of DESA for personal injury, property damage or any
other damage whatsoever, including consequential and incidental damages, arising from the sale
or use of this product shall not exceed the purchase price of this product.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
For information about this warranty write:
101437-01
REV. F
7/95
For Technical Assistance or Repair on Your
Remington Powder Actuated Tool, Call
Technical Services Department
1-800-323-5190.
For Certification Procedures,
Call 1-800-626-2237.
P.O. Box 90004
2701 Industrial Drive
Bowling Green, KY 42102-9004
502-781-9600

Navigation menu