Remotesolution CRB76B IR&RF; Remote User Manual

Remote Solution Co., Ltd. IR&RF; Remote

User Manual

Meet Your Remote Pair Remote for “Aim Anywhere” ControlTurn On Your Remote  Control Your TV’s Power and VolumeRemote with Aim Anywhere Start1Press and hold the Setup button (about 3 seconds) until the Status LED changes from red to green.Press the XFINITY button. Follow the on-screen instructions to enter the 3-digit code that appears. Once the code is correctly entered, your XFINITY Remote is paired with the device. Pick up your remote and remove the “Pull” tab (on back) by pulling away from the remote. The Status LED will blink green four times as the remote powers up (about 5 seconds).Turn on your TV.Turn on your set-top box.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications.There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:  •   Reorient or relocate the receiving antenna.  •   Increase or decrease the separation between the      equipment and receiver.  •   Connect the equipment into an outlet on a circuit      dierent from that which the receiver is connected.  •   Consult the dealer or an experienced remote control/     TV technician for help.  •   It is strongly recommended that the TV be plugged      into a separate wall outlet.The user is cautioned that changes and modications made to this equipment without the approval of the manufacturer could void the user’s authority to operate this equipment.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.“Caution” : Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human contact during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.Radio Exposure Statement: This equipment complies with the FCC radiation exposure limits set forth for devices operating in an uncontrolled environment. This equipment should be operated with a minimum distance of 2 cm between the radiator and front of face. Using the list on the right, nd the rst 5-digit code for your TV manufacturer.Press and hold the Setup button (about 3 seconds) until the Status LED changes from red to green.Enter in the rst 5-digit code for your TV manufacturer. The Status LED should blink green twice.Verify that the code was accepted by using your remote to adjust volume and turn the TV on and o.ABCABCABCD32 4Status LEDAll PowerSearchDiscover content by channel, program or key words.Number KeysUse predicitve text (T9) to quickly search for content.TV Input Changes to the next available input on your TV (if programmed in Step 4)TV PowerXFINITY / MenuAccess Guide, Saved, XFINITY On Demand, Apps, Search and Settings.SetupProgram remote for Aim Anywhere or to control your TV or audio device.Control your set-top box without having to point at it, even when it is inside a cabinet or entertainment center. Your remote arrives with the AA batteries already installed, but not activated. Here is how to power it on for the rst time.Need to remove Aim Anywhere control? Press and hold the Setup button on the remote until the status LED changes from red to green. Press A on the remote. If the status LED blinks green twice, you have successfully removed Aim Anywhere.Not working? Make sure the battery tab from your remote is removed,  your TV is on and you are entering the correct 3-digit code on your TV screen.Not working? Try the second code listed. Still not working? Visit xnity.com/remotes for a complete list of manufacturer codes.BackIf your code isn’t listed or you would like to control an audio device, visit xnity.com/remotes.Popular Manufacturer CodesLG  10178, 11265Panasonic  10051, 10250Samsung  10812, 10060Sanyo  10154, 10159Sony  10000, 11100Sharp   10093, 10165Toshiba  10156 , 11156Vizio  11758 , 11756FCC Compliance Statement
Control remoto con Aim AnywhereInicio1 32 4Keep for future reference, but if you decide to toss, please recycle.Get Started Guide v.1.0Need help?Visit xnity.com/xtv Conozca su control remoto1Luz LED de estadoTodo encendidoBuscarBusque contenido por canal, programa o palabras clave.Teclas de númerosUse el texto predictivo (T9) para buscar contenido con rapidez/facilidad.Entrada de TV  Cambios para la siguiente entrada disponible en su televisor (si se programó en el paso 4).Encendido de televisorXFINITY/MenúAcceda a guía, guardados, XFINITY On Demand, Apps, búsqueda y conguración.Conguración Programe el control remoto para Aim Anywhere o controle su TV o equipo de audio.Encienda su control remotoTome su control remoto y quite la pestaña “Pull” (situada en la parte posterior) separándola del control remoto. La luz LED de estado parpadeará en verde cuatro veces mientras se enciende el control remoto (unos 5 segundos).Encienda su televisor.Encienda su decodicador.ABC2Su control remoto se le entrega con baterías AA ya instaladas, pero no activado. A continuación se muestra cómo debe encenderlo la primera vez.BackSincronice el control remoto para controlar “Aim Anywhere”  Mantenga presionado el botón Setup unos 3 segundos, hasta que la luz LED de estado cambie de rojo a verde.Presione el botón XFINITY.  Siga las instrucciones en pantalla para ingresar el código de 3 dígitos que aparece.Una vez que el código se haya ingresado correctamente, su control remoto de XFINITY queda sincronizado con el aparato.ABC3Controle su decodicador sin tener que apuntar hacia él, incluso si está dentro de un armario o en un centro de entretenimiento.¿Necesita eliminar el control Aim Anywhere? Mantenga presionado el botón Setup del control remoto hasta que la luz LED de estado cambie de rojo a verde. Presione A en el control remoto. Si la luz LED de estado parpadea dos veces en color verde, eliminó satisfactoriamente el control Aim Anywhere.¿No funciona? Asegúrese de que ha retirado la pestaña junto a las baterías de su control remoto, su TV está encendido y ha ingresado el código de 3 dígitos correctamente en la pantalla del televisor.Controle el encendido y el volumen del televisorEncuentre en la lista de la derecha el primer código de 5 dígitos correspondiente al fabricante de su televisor.Mantenga presionado el botón Setup unos 3 segundos, hasta que la luz LED de estado cambie de rojo a verde.Ingrese el primer código de 5 dígitos correspondiente al fabricante. La luz LED de estado debe parpadear en color verde dos veces.Verique que el código ha sido aceptado usando su control remoto para ajustar el volumen y encender y apagar el televisor.ABCD4¿No funciona? Pruebe el segundo código de la lista. ¿Aún no funciona? Visite xnity.com/remotes para una obtener lista completa de códigos de fabricantes.Si su código no está en la lista o le gustaría controlar un equipo de audio, visite xnity.com/remotes.Códigos de fabricantes más comunesLG    10178, 11265Panasonic  10051, 10250Samsung  10812, 10060Sanyo  10154, 10159Sony  10000, 11100Sharp   10093, 10165Toshiba  10156 , 11156Vizio  11758 , 11756

Navigation menu