Remote Technologies RTI1100 Universal System Remote User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1072725
Application ID	GXq+4ZgcCWBeS6TYIGiQ+A==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.64kB (283050 bits)
Date Submitted	2009-02-25 00:00:00
Date Available	2009-02-25 00:00:00
Creation Date	2008-10-29 10:53:17
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2008-10-29 10:54:21
Document Title	User manual
Document Creator	Adobe InDesign CS3 (5.0.3)

® Under Control ®
It’s
It’s Under Control
T1-B
Operation Guide
Universal System Controller
70-21XXXX-XX V 1.0
T1-B
Universal System Controller
Copyright © 2008
Remote Technologies Incorporated
All rights reserved.
It’s Under Control ®
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received including
interference that may cause undesired operation.
FCC ID: MMURTI1100
CAN:
3166-RTI1100
117 612 914
DECLARATION OF CONFORMITY (DOC)
The Declaration of Conformity for this product can be found on the RTI
website at: www.rticorp.com/declaration
T1-B
Universal System Controller
BATTERY DISPOSAL
Li-ion
For environmental reasons, your T1-B Universal System
Controller uses “environmentally sound” Lithium-ion
rechargeable batteries. These batteries do not contain any
poisonous heavy metals that can damage the environment.
In the interest of recycling, please do not dispose of these batteries in the
household waste at the end of their useful life. Instead, dispose of them at
an appropriate collection site.
SAFETY SUGGESTIONS
Read Instructions. Read all safety and operating instructions before
operating the unit.
Retain Instructions. Keep the safety and operating instructions for future
reference.
Heed Warnings. Adhere to all warnings on the unit and in the operating
instructions.
Follow Instructions. Follow operating instructions and instructions for use.
Heat. Keep the unit away from heat sources such as radiators, heat
registers, stoves, etc., including amplifiers that produce heat.
Power Sources. Connect the unit only to a power supply of the type
described in the operating instructions, or as marked on the unit.
Power Cord Protection. Route power supply cords so that they are not
likely to be walked on or pinched by items placed on or against them,
paying particular attention to the cord plugs at power receptacles and at the
point at which they exit from the unit.
Water and Moisture. Do not use the unit near water—for example, near a
sink, in a wet basement, near a swimming pool, near an open window, etc.
Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled
into the enclosure through openings.
Servicing. Do not attempt any service beyond that described in the
operating instructions. Refer all other service needs to qualified service
personnel.
Damage Requiring Service. The unit should be serviced by qualified
service personnel when:
The power supply cord or the plug has been damaged.
Objects have fallen or liquid has been spilled into the unit.
The unit has been exposed to rain.
The unit does not appear to operate normally or exhibits a marked
change in performance.
The unit has been dropped or the enclosure has been damaged.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.
It’s Under Control ®
Limited Warranty and Disclaimer
Remote Technologies Incorporated warrants its products for a period of
one (1) year (90 days only for included battery packs) from the date of
purchase from Remote Technologies Incorporated or an authorized Remote
Technologies Incorporated distributor.
This warranty may be enforced by the original purchaser and subsequent
owners during the warranty period, so long as the original dated sales receipt
or other proof of warranty coverage is presented when warranty service is
required.
Except as specified below, this warranty covers all defects in material and
workmanship in this product. The following are not covered by the warranty:
Damage resulting from:
1.
Accident, misuse, abuse, or neglect.
2.
Failure to follow instructions contained in this Guide.
3.
Repair or attempted repair by anyone other than Remote Technologies
Incorporated.
4.
Failure to perform recommended periodic maintenance.
5.
Causes other than product defects, including lack of skill, competence or
experience of user.
6.
Shipment of this product (claims must be made to the carrier).
7.
Being altered or which the serial number has been defaced, modified or
removed.
Remote Technologies Incorporated is not liable for any damages caused by its
products or for its failure of its products to perform, including any lost profits,
lost savings, incidental damages, or consequential damages.
Remote Technologies Incorporated is not liable for damages based upon
inconvenience, loss of use of the product, loss of time, interrupted operation,
commercial loss, any claim made by a third party or made by you for a third
party.
Remote Technologies Incorporated’s liability for any defective product is
limited to repair or replacement of the product, at our option.
If your T1-B Universal System Controller needs service, please contact
Remote Technologies Incorporated by telephone, fax or E-mail for return
information. Please do not return products to Remote Technologies
Incorporated without return authorization.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated without the prior written notice of Remote
Technologies Incorporated.
The information contained in this document is subject to change without
notice. Remote Technologies Incorporated shall not be liable for errors or
omissions contained herein or for consequential damages in connection with
the furnishing, performance, or use of this guide.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other brands and their products are trademarks or registered trademarks of
their respective holders.
T1-B, Integration Designer™, and the RTI logo are registered trademarks of
Remote Technologies Incorporated.
T1-B
Universal System Controller
It’s Under Control ®
table of Contents
Federal Communications Commission Notice............... 3
Battery Disposal.......................................................... 4
Safety Suggestions...................................................... 4
Limited Warranty and Disclaimer ............................... 5
Contents...................................................................... 7
Chapter 1 - Welcome................................................... 9
Compatibility............................................................ 9
Unpacking and Inspection.......................................... 9
Product Contents...................................................... 9
Software requirements............................................. 10
Features................................................................. 10
Chapter 2 - Introduction............................................. 11
Important Notes...................................................... 11
Cleaning................................................................. 11
Battery and Docking Station...................................... 11
Remote Reference.................................................... 12
Docking Station Reference........................................ 14
Chapter 3 - Operation................................................. 15
Getting Started....................................................... 15
Source Buttons........................................................ 15
Chapter 4 - Specifications........................................... 17
Chapter 5 - Troubleshooting....................................... 19
Chapter 6 - Service and Support................................. 21
Index......................................................................... 23
T1-B
Universal System Controller
It’s Under Control ®
Chapter 1
Welcome
Thank you for purchasing the T1-B Universal System Controller.
The T1-B is the second generation of RTI’s popular T1 universal system
controller. Completely customizable and programmable, the T1-B allows all
other factory remote controls to be combined into one simple, ergonomic
user interface providing powerful one-handed system control. Featuring a
sleek new industrial design and perfect assortment of keypad buttons for
commonly used functions, the T1-B can operate today’s sophisticated media
system, no matter how complex, at an affordable price.
Perfect for any media room, the T1-B can also be completely customized to
control virtually any aspect of the home or office. Buttons can be individually
programmed to control devices or execute multi-step macros for complex
installations involving many components. Source buttons can be custom
labeled to match the device being controlled for more intuitive control. The
integrated tilt switch, coupled with a Lithiumion battery and charging dock
insure hours of uninterupted control.
When other RTI devices are employed, the T1-B is capable of RF
transmission thru walls and cabinets, RS-232 control, contact closures,
power sensing and much more. Whether used as a standalone device
or integrated into a complete RTI control solution, the T1-B will provide
powerful and intuitive control of any electronics system - from simple to
sophisticated.
COMPATIBILITY
The T1-B and Integration Designer™ software are compatible with infrared
(IR) commands with carrier frequencies between 15KhZ and 460KhZ, as
well as those commands that do not use a carrier. This covers virtually all
of the remotes that exist to date.
UNPACKING AND INSPECTION
After unpacking your new T1-B Universal System Controller, save all of the
packing materials in case you ever have to ship the unit.
Thoroughly inspect the T1-B and packing materials for signs of damage.
Report any damage to the carrier immediately. Report any equipment
malfunctions to Remote Technologies Incorporated or an authorized
Remote Technologies Incorporated distributor.
PRODUCT CONTENTS
Contents within the box include the following items:
One (1) T1-B universal system controller
One (1) Docking station.
One (1) Universal power supply for docking station
One (1) Operation guide.
T1-B
Universal System Controller
Chapter 1 | welcome
SOFTWARE REQUIREMENTS
The recommended minimum system requirements needed to run the
Integration Designer™ software are as follows:
Windows 2000®, Windows XP® or later version.
A free USB port.
At least 64 Megabytes of RAM.
At least 150 Megabytes of free disk storage.
Screen resolution of 800x600 with 16-bit color.
A mouse is required.
Optional printer for printing reports.
FEATURES
The T1-B provides superior quality and reliability as well as these features:
Comfortable ergonomic design permits effortless, one-handed
operation.
Tilt switch can automatically turn on the backlight when picked up.
Eight source and four general purpose assignable/programmable
keypad buttons with interchangeable key labels.
Forty assignable/programmable keypad buttons.
Intuitive layout of keypad buttons for commonly used functions.
Transmits IR and RF (or both -on a single button press!).
Optional RF receiver allows you to transmit through walls,
cabinets, etc.
System includes a Lithium-Ion battery and docking station.
Extremely wide IR transmitting frequency range.
Optional ‘Voltage’ and ‘Video’ sensing modules to monitor power status
of equipment when used with certain RTI processors.
Optional interface for RS-232 controlled equipment when used with
certain RTI processors.
Non-volatile Flash memory stores your system configuration even when
power is not present.
Field upgradable firmware.
USB Programming.
10
It’s Under Control ®
Chapter 2
| introduction
IMPORTANT NOTES
Please read these important notes about the T1-B:
The T1-B should be placed in an area where it is around normal room
temperature (between 60° F to 90° F).
Do not let the T1-B get wet. It should not be handled with wet hands or
placed in an area where it could get wet.
Do not subject the T1-B to smoke, dust, or vibrations.
Only use the power supply that is provided with the T1-B. Using the
wrong type of power supply may result in damage to the battery or
electronic components.
Do not disassemble the unit. Service of the T1-B should be performed
by authorized personnel only.
CLEANING
To clean your T1-B, lightly dampen a lint-free cloth with a mild detergent,
and wipe the keypad and outer surfaces.
BATTERY AND DOCKING STATION
The T1-B uses a Lithium-Ion rechargeable battery. This battery does
not exhibit any type of “Memory Effect” from being charged too often.
Since the T1-B can safely be charged after each use, a docking station is
included for convenience. If left out of the docking station, the T1-B will
remain in sleep mode for 1 – 2 months before shutting down. At that point
the battery must be recharged.
If the T1-B battery capacity is reduced to approximately one hour of
remaining run-time, the Status LED will illuminate red while the unit is
powered-up.
The T1-B Docking Station can be placed on a flat surface such as a shelf
or table, or it can be mounted to a wall using the mounting holes on the
back of the unit. The docking station LED illuminates to indicate a charge
in progress. The LED will turn off when the battery in the unit is fully
charged.
A fully discharged battery will take approximately 2-4 hours to completely
re-charge.
The T1-B can remain in the docking station indefinitely without damage to
the battery.
11
T1-B
Universal System Controller
Chapter 2 |
INTRODUCTION
IR Transmission Window
Source (8)
Keypad Buttons
General Purpose (4)
Keypad Buttons
Predefined Keypad Buttons
Backlight Button(?)
Front
12
It’s Under Control ®
Chapter 2 |
INTRODUCTION
Lithium-Ion Battery Pack
USB Prpogramming Port
Docking Station Contacts
Back
13
T1-B
Universal System Controller
Chapter 2 |
INTRODUCTION
GETTING STARTED
Charge Contacts
Charge LED
Docking Station Top
X-X/X in.
(xx mm)
Wall Mount Holes
Wire Guide
Docking Station Side
14
Power Jack
It’s Under Control ®
Chapter 3
| operation
GETTING STARTED
Start by inserting the battery connector into the mating plug on the T1-B.
Make sure the connector is oriented properly before attempting to insert it.
The T1-B is turned-on by touching any keypad button. If the tilt sensor is
enabled, picking up the unit will also turn it on.
THE SOURCE BUTTONS
The eight source buttons at the top of the T1 keypad have a special
function, so they behave differently from the other buttons. These buttons
are used to select the active source “page.” Whenever asource button
is selected, all of the other buttons on the keypad will switch to the
programming associated with that page. In order to indicate the active
page, a blue LED is always illuminated behind one of the source buttons.
Despite their special function, the source buttons can be programmed to
run commands or macros in the same way that the other buttons can.
15
T1-B
16
Universal System Controller
It’s Under Control ®
Chapter 4
Power
Power Management
Infrared Control
Range
Infrared Frequency
Transmission Range
Specifications
3.6 VDC, 1050mAh Lithium-Ion Battery Pack
Automatic On/Off (tilt switch)
30 feet (9.1 meters) @ 60 degrees
15 kHz - 460 khz
Radio Frequency
Control Range
Up to 100 feet (30.5 meters)
with optional System Interfaces/Processors
Radio Frequency
Carrier
433 MHz
Operating
Temperature
Operating Humidity
Backlight
Nominal Run Time
on Full Charge
Standby Time on
Full Charge
+32° F to +122° F (0° C to +50° C)
5% to 95% Non-condensing
Blue EL
20 hours continuous use
(20 to 30 days on average use)
30 days
Battery Charge Time 3 to 4 hours
Total System
Memory
256K Flash (non-volatile) memory
Device Capability
Total number of devices is limited only by memory
Macro Capability
Up to 64 steps per macro
Total number of macros is limited only by memory
Macro capability on every button
Communications
USB programming port
Dimensions
(L x W x D)
9.3 in (235mm) x 2.5 in (64mm) x 1.1 in (28mm)
Enclosure
High-impact molded ABS plastic
Weight
7 oz. (200 g) with battery pack
Warranty
One Year (Parts & Labor) / 90 days on battery
All specifications subject to change without notice.
17
T1-B
18
Universal System Controller
It’s Under Control ®
Chapter 5
Troubleshooting
If you are having problems with your T1-B Universal System Controller,
please read the information below before contacting technical support.
If you continue to have problems, see Chapter 6 for more information on
contacting RTI technical support.
USB COMMUNICATION PROBLEMS
Make sure the battery pack connector is attached properly and the
battery is charged.
Verify that your PC is using Windows 2000® or higher. The
TheaterTouch Designer software requires a USB device driver that may
not be installed on earlier versions of Windows.
Make sure you are using the programming cable that was supplied by
RTI and that both ends are connected securely.
Make sure the PC detects the presence of the T1. If it doesn’t, unplug
the USB cable, wait for about ten seconds, and plug it in again.
If the download fails after some data has been transferred, try
resending the program.
IR CODE PROBLEMS
If you are using an IR repeater system, make sure it is working
correctly with the original OEM remote. If not, you will need to
troubleshoot the IR repeater system.
If you are still having problems, try adjusting the IR code “Minimum
Repeats” value in the Integration Designer™ programming software.
If the IR code is executed inside a macro that contains multiple IR
codes, try inserting a small time delay before the problem code. If
there already is a delay, try increasing it.
19
T1-B
20
Universal System Controller
It’s Under Control ®
Chapter 6
Service and Support
For news about the latest updates, new product information, and new
accessories, please visit our web site at:
www.rticorp.com
CONTACTING RTI
For general info, you can contact RTI at:
Tel. (952) 253-3100
Fax (952) 253-3131
info@rticorp.com
RTI TECHNICAL SUPPORT
At RTI, customer service and satisfaction is an utmost priority. If you are
encountering any problems or have a question about your RTI product,
please contact RTI Technical Support for assistance.
RTI provides technical support by telephone, fax or e-mail. For the highest
quality service, please have the following information ready, or provide it in
your fax or e-mail.
Your Name
Company Name
Telephone Number
E-mail Address
Product model and serial number (if applicable)
If you are having a problem with hardware, please note the equipment in
your system, a description of the problem, and any troubleshooting you
have already tried.
If you are having a problem with software, please note what version you
have installed, the operating system on your PC, a description of the
problem, and any troubleshooting you have already tried.
If you are calling about a software or programming question or problem,
please be at you computer when you place your call. This will considerably
speed up the troubleshooting process.
For technical support or assistance with your T1-B, software, or
accessories, contact RTI at:
(952) 253-3137
support@rticorp.com
www.rticorp.com
For questions regarding service or repair of your T1-B, contact RTI at:
(952) 253-3136
service@rticorp.com
www.rticorp.com
Please do not return products to RTI without return authorization.
21
T1-B
Universal System Controller
Chapter 6 |
Service and Support
Shipment of T1-B for Service
RTI will pay all labor and material expenses for all repairs covered by this
product’s warranty. If necessary repairs are not covered by warranty, or if
a unit is examined which is not in need of repair, you may be charged for
the repairs or examination.
If it is necessary to ship the T1-B Universal System Controller for service:
Please pack it securely (we suggest that it be insured).
Do not include accessories such as power cords or manuals unless
instructed to do so.
You must pay any shipping charges incurred in getting your T1-B Universal
System Controller to RTI. RTI will pay reasonable return shipping charges
via a carrier of our choice to any destination within the United States if the
repairs are covered under warranty.
A copy of the original dated sales receipt must be provided whenever
warranty service is required. You will need this receipt to establish the date
of purchase.
22
It’s Under Control ®
Index
Contents............................................................................ 7
Features........................................................................... 11
Federal Communications Commission Notice........................... 3
Introduction...................................................................... 12
Battery......................................................................... 12
Battery Disposal............................................................... 4
Cleaning....................................................................... 11
Docking Station............................................................. 14
Getting Started.............................................................. 15
Remote Reference, Front................................................. 12
Remote Reference, Back.................................................. 13		
Limited Warranty/Disclaimer................................................. 5
Operation......................................................................... 15
Product Contents................................................................. 9
Safety Suggestions.............................................................. 4
Service and Support.......................................................... 21
Contact RTI................................................................... 21
Shipment for Service...................................................... 22
Technical Support........................................................... 21
Specifications.................................................................... 17
Troubleshooting................................................................. 19
23
T1-B
Universal System Controller
It’s Under Control ®
Remote Technologies Incorporated
5775 12th Avenue East, Suite 180
Shakopee, MN 55379
Tel: 952-253-3100
Fax: 952-523-3131
www.rticorp.com
© 2008 Remote Technologies Inc. All rights reserved. Printed in Taiwan.
24

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Instance ID                     : uuid:ee1e7132-9a95-44f5-9e61-b268a01b2ced
Document ID                     : adobe:docid:indd:786e1b63-a5d1-11dd-b3c4-f8e0edbf59b1
Rendition Class                 : proof:pdf
Derived From Instance ID        : 786e1b62-a5d1-11dd-b3c4-f8e0edbf59b1
Derived From Document ID        : adobe:docid:indd:bcfcb962-a55a-11dd-9e38-f127918a0e47
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 300.00, 72.00, 300.00, 300.00
Manifest Placed Y Resolution    : 300.00, 300.00, 72.00, 300.00, 300.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:8A2722EB36A5DD11B4D4E3485CB687DC, uuid:F68D23895582DC118DAEFEFB3E736064, uuid:4b768568-c642-4c77-a48e-56869ebc2fd7, uuid:822722EB36A5DD11B4D4E3485CB687DC, uuid:F68D23895582DC118DAEFEFB3E736064
Manifest Reference Document ID  : uuid:892722EB36A5DD11B4D4E3485CB687DC, uuid:F58D23895582DC118DAEFEFB3E736064, uuid:D05E7940390ADD118131F9298F1B0430, uuid:812722EB36A5DD11B4D4E3485CB687DC, uuid:F58D23895582DC118DAEFEFB3E736064
Create Date                     : 2008:10:29 10:53:17-05:00
Modify Date                     : 2008:10:29 10:54:21-05:00
Metadata Date                   : 2008:10:29 10:54:21-05:00
Creator Tool                    : Adobe InDesign CS3 (5.0.3)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7526 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 24
Page Layout                     : TwoColumnRight
Creator                         : Adobe InDesign CS3 (5.0.3)

EXIF Metadata provided by EXIF.tools