Remotec Technology BW2100TX-00 Garage Door Opener User Manual

Download:
Mirror Download [FCC.gov]
Document ID	7611
Application ID	+H5aVC0koAJtUZbLz5PdjA==
Document Description	USER MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.45kB (105660 bits)
Date Submitted	1998-09-19 00:00:00
Date Available	1998-10-30 00:00:00
Creation Date	1998-09-19 11:13:01
Producing Software	Acrobat 3.0 Import Plug-in
Document Lastmod	1998-09-19 11:14:01
Document Title	USER MANUAL
Document Creator	Acrobat 3.0 Import Plug-in

18—SEP-1998 17289 REMOTEC TECHNOLOGY LTD. +852 2314 1886 F.51
.;Z§l>4%&fifii97p%f -/Aé52§:62:;/
Bw2100 — GARAGE DOOR OPENER USER MANUAL
1.FCC:
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a curcuit different from that to
which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.
2. User Setup
Congratulate on buying one of the successful products from Remotec Technology
Ltd. BW2100 is a two buttons, direct replacement for the digital radio
transmitters from many brands. The following steps will help you setup the
garage door opener. -
a) Unscrew the top cover and open up the unit, one should see the features as
illustrated below. Button K1 and K3 can be configured independently to simulate
different brands of garage door opener. This allows you to work with different
brands of receiver with only one transmitter.
Direction towards windshield
Store‘Button
Remotec
MODEL. flew?
_..¢u—.
R0“? OENMQf
O PEEL .M!NARV lg“ n “t“! "h":
1: (“m-mm on v 1
\ cm 1
if! -U".[‘\(1.
niwrrwui
uLAifmAh ALE
iwtfilfiéwflufl .
I};
‘ '-f.f' ‘l
A...
uwodtw
Z" ? 7-1
4&1sz
lB—SEP-1998 17:18 REMOTEC TECHNOLOGY LTD. +852 2314 1886 P.B2
Switches A 'to C: of SW2 is for selecting frequency of transmission whereas
switches I) must be set to “ON” position. Switches E to ii is for selecting
manufacturer of your receiver. The tables below summarised the settings that
you need to configure your transmitter. '
Manufacturer select (SW?)
_"nn
—Hnn-
IHHEHIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIMIIIIIIIIIIIII
Table é-
c) Use a ball point pen or paper‘clip to set switches A to C as shown
in table 2 to match the frequency of your receiver. Then set switches E
to H as shown in table 1 to match the brand of your receiver.
d) Most digital transmitters will have 9 or 12 code switches inside
similar to switch 1 as shown above. Move the coding switches (labeled 1-
12 of SWl) to match the setting of your existing unit‘ You will only need
to set the same number of DIP switches as in the original transmitter.
Fer- example, if your unit has only' 9 switches, just set the first 9
SWi.tches of SWI the remaining switches can be left in any position. Note
that the switches of SWl have 3 settings, ‘+‘ Middle and ‘- -'. if your
or.iginal transmitter’ s DIP switches have only two settings, be sure that
the DIP SWitches are set either all the way to ‘+' or ‘-'.
A h PT—fi A fififi {I H l A 4 ”fir—v fiWd A A flflf- fiflfi‘ fl
fi’fi
18~SEP—1998 17118 RENOTEC TECHNOLOGY LTD. +852 2314 1886 P.83
e) After setting the switches SW1 and SW2 for the desired code mentioned
above, press ‘Store’ and ‘K1' for a second to store your settings into
‘Kl' key. The LED will flashes twice slowly after a successful storing
process.
The LED will flashes several times quickly if the storing
process is wrong or failed, this may be due to incorrect
setting of manufacturer (SW2) or damage of the unit.
After storing a code, release all keys and repeat the setup procedure
again to store for key ‘K3'. Note that different code settings can be
stOIed into ‘K1’ and ‘K3'.
The LED will flashes several times quickly if no code was
stored in the key.
3) Operation
After setup the garage door opener, simply press ‘Kl' or ‘K3’ (but not both),
the code stored in those keys will be transmitted and the LED will lights up to
confirm of your key press. For best result. horizontally clip your transmitter
under the shade cover near the windshield. The front of the transmitter should
points towards the windshield. The shade cover will help buffer any shock that
occurs to the transmitter during driving. To operate, press ‘Kl’ or ‘K3' with
only ONE hand for transmission . The other hand should be on the driving wheel
for safety.
4) Precautions
1. Keep water away from this product as much as possible. Continual
exposure to rainwater may damage the product.
2. Do not expose the product to direct sunlight for days or even months.
Clipping the transmitter under shade cover will minimize continual
sunlight exposure.
3. Low battery power is indicated by continued short range, intermittent
operation. When battery replacement is necessary, open switch access»
cover used to configure the transmitter. Remove old batterie and replace
with fresh 9V battery (preferably alkaline type).
4. Do not let the transmitter hangs around freely inside the car.
Shocks during driving may damage the product. Knocking down of the
transmitter during driving may also cause distractions to the driver.
5) warning}
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
TUTQL P.@3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 1998:09:19 11:14:01
Create Date                     : 1998:09:19 11:13:01
Producer                        : Acrobat 3.0 Import Plug-in
Creator                         : Acrobat 3.0 Import Plug-in
Page Count                      : 3

EXIF Metadata provided by EXIF.tools