Remotek WU210P USB Wireless LAN User Manual WU210P quick start manaul

Download:
Mirror Download [FCC.gov]
Document ID	176344
Application ID	kWm2DcEp75hFfOQKsarSCA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	60.08kB (751035 bits)
Date Submitted	2001-10-28 00:00:00
Date Available	2001-10-28 00:00:00
Creation Date	2001-10-18 11:19:52
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2001-10-24 15:08:08
Document Title	Microsoft Word - WU210P quick start manaul.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Owen Chen

User Manual
WU210P
USB Adaptor
Version 1.0—July 2001
Copyright Statement
No part of this publication may be reproduced in any form or by any means or
used to make any derivative such as translation, transformation, or adaptation
without permission form Remotek Corporation, as stipulated by the United
States Copyright ACT of 1976.
FCC Certifications
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These Limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Shielded interface cables must be used in order to comply with emission limits.
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void your authority to operate the
equipment
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your
body.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received. Including
interference that may cause undesired operation.
Contents
1.
2.
3.
4.
4.1.
4.2.
4.3.
4.4.
4.5.
4.6.
5.
Introduction ..........................................................................................................4
Installation Overview ..........................................................................................5
Installation Procedure of WU210P ....................................................................6
Configuration Utility ............................................................................................9
“Status” tab ..................................................................................................9
“Statistics” tab............................................................................................11
“Site Survey” tab........................................................................................12
“Encryption” tab.........................................................................................13
“Advanced” tab...........................................................................................14
“Version” tab...............................................................................................14
Technical specifications of WU210P................................................................15
1. Introduction
Thank you for purchasing USB Wireless LAN Adaptor-WU210P from Remotek
Corp.. This quick start manual will assist you with the installation procedure.
The package you have received should contain the following items:
WU210P USB WLAN Adaptor
USB to Mini USB Cable
User manual
CD ROM containing Wireless LAN Management utility and drivers
Note: if anything is missing, please contact your vendor.
2. Installation Overview
Here are some steps you will perform in establishing your wireless network
connection:
Install the Access Point at first. AP is needed in case of infrastructure
network mode.
Install the software using the Installation CD-ROM.
Insert the Wireless LAN adaptor (WU210P).
Install the driver of USB WLAN adaptor.
Install the network protocols required to communicate on your network.
Most likely you will need the TCP/IP protocol.
3. Installation Procedure of WU210P
Please follow the following steps one by one in order to install the USB WLAN
Adaptor successfully.
Step 1. Power on your computer and allow Window 95/98/2000 to load
fully.
Step 2. Be sure that there is no USB adaptor inserted yet.
Step 3. Insert the given Installation CD-ROM and then click on the setup.exe.
Step 4. Give the path of the destination folder.
To change the path of the destination folder click on Browse
After all, click Next to continue.
Step 5. Type the program folder name.
Step 6. Last check before install the program.
Step 7. It takes a few seconds for copying the utility files and then click on
Finish to complete the installation
Step 8. Message that notifies you to restart your computer may pop up.
Select Yes. It will shut down your computer and restart.
Step 9. Insert the WU210P - USB WLAN Adaptor into USB slot, windows will
install the driver automatically.
Step 10. If the Configuration & Monitor Utility icon is not on system tray, it
shows the installation is not successful. Select Uninstall WLAN
Monitor Utility in program folder to remove. Restart your computer
after uninstalling the driver to make the changes effective.
Step 11. If you find the Red sign on system tray, which means your Wireless
LAN Adaptor haven’t connected to an Access Point Successfully.
Please double-click on the red sign on system tray to open
Configuration & Monitor Utility. Select Site Survey tab, and click
Re-Scan to find all site nearby. You may double-click on the site that
you want to connect to.
Step 12. Modify TCP/IP settings of Windows. You can select either Static or
DHCP setting. If you use the static IP setup then enter the IP value,
Subnet masking, DNS, and Gateway Address values. After setting
these parameters appropriately, click OK to make the settings
available. If you are operating on Windows 95/98, message that
notifies you to restart your computer should pop up. Select Yes. It
will shut down your computer and restart to make settings available.
4. Configuration Utility
The Configuration Utility is a powerful application that helps you to configure
the WU-210P and monitor the statistics of the communication. Please keep on
mind that this utility can be used to change the following configuration
parameters when the cards are active. The Configuration Utility appears as icon
on the system tray of Windows every time the card is running. You can open it
by double-clicking on the icon.
Users can navigate through sheets. “Exit” button will exit application. Here we
explain the use and meanings of the various screen messages.
4.1.
“Status” tab
You can change the configuration by clicking on the “Change”, and click
“Submit” after the configuration has been changed.
Operation mode: shows one of these network modes:
Infrastructure – This mode of operation requires the presence of an
802.11 Access Point. All communication is done via the Access Point.
Ad-Hoc – This mode is for the 802.11 peer-to-peer operation. All
communication is done from client to client without the use of an Access
Point. The user should switch to the channel that he wants to approach.
The first method is to set the clients with the same channel.
Channel: shows radio channel number used for networking. Only Access
Points and Ad-Hoc nodes can create a BSSID therefore this parameters is not
active if the mode is infrastructure. Infrastructure client nodes will always go
the same channel as their AP.
SSID: shows the SSID of the BSS that you want to join.
Tx Rate: shows the transfer rate. There are 1 Mbps, 2M bps, 5.5 Mbps, 11
Mbps, and auto mode. If you select auto mode, the card will select the most
suitable rate automatically.
Power Mgmt Mode: shows Power Management modes:
Active – Adaptor will always be in active mode.
Power Save – Adaptor will save power when it is idle.
Signal strength: This bar shows signal strength level. The higher the blue bar
is, the more power of radio signal received by Remotek USB WLAN adaptor is.
This indicator helps to find the most comfortable antenna/workstation position
for quality network operation.
Link quality: The measured signal level gives the overall Link Quality and
Connection Status.
10
4.2.
“Statistics” tab
It shows all amounts of packets that received or transmitted by the adaptor.
Data Field: shows the amounts of data packets transmitted or received by the
adaptor. And also shows how many data packets are transmitted or received
successfully or not.
Management Field: shows the amounts of management packets transmitted
or received by the adaptor. And also shows how many management packets are
transmitted or received successfully or not.
Rejected Packets Field: shows the amounts of rejected packets transmitted
or received by the adaptor.
11
4.3.
“Site Survey” tab
It shows all APs or adaptors in Ad-Hoc mode nearby. You may click Re-Scan to
collect the wireless device information to know the BSSID and Ch(Channel).
If you want to connect to any device on the list, double-click on the device. The
adaptor will connect to the device you have selected.
12
4.4.
“Encryption” tab
You may desire an additional measure of security on your wireless network,
which can be achieved by using WEP(Wired Equivalent Privacy) encryption.
WEP encrypts each frame transmitted from the radio using one of the keys
entered from this panel. When an encrypted frame is received it will only be
accepted if it decrypts correctly. This will only happen if the receiver has the
WEP key used by the transmitter.
This panel allows the entry of four keys, which can then be written to the driver
and registry. Each key must consist of 10 digits. If entered incorrectly, program
will not write keys to driver. Key1-Key4: These four fields must be used to enter
the keys.
Submit- this button updates the driver with the four keys displayed in Key1
through Key4. The keys are also written to the registry for permanent storage.
Encryption- this checkbox enables or disables encryption operation. When it is
checked through 64 bits and 128 bits, encryption is enabled. When disabled is
checked, encryption is hidden.
13
4.5.
“Advanced” tab
We can find and change some advance settings here. They are Preamble
Type, Fragmentation Threshold, and RTS/CTS Threshold. Note that the
adaptor has a feature to select the preamble type from AP automatically.
4.6.
“Version” tab
It shows Driver Version, Firmware Version, and Application Version.
14
5. Technical specifications of WU210P
Model No
WU210USB
Standard
IEEE802.11b
Card Type
USB 1.0
Transmission range
Outdoor: 100~300M, Indoor: 30~100M
Radio Type
Direct Sequence Spread Spectrum
Data Rate
1,2,5.5,11Mbps per Channel
Frequency band
USA & Canada:2.400 GHz ~2.4835GHz
Europe: 2.4000~2.4835GHz
Compatibility
Windows 98/2000/ME
Certification
FCC, CE
LED Indicators
PWR, TX, RX
Power consumption
Dimensions
Weight
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Data Encryption
Software
USB Cable
5V DC
100x65x14mm
29g
0℃ to 55℃, 32℉ to 131℉
-20℃ to 55℃, -4℉ to 158℉
0% to 70% Non-Condensing
0% to 95% Non-condensing
64 bit or 128 bit KEY WEP Encryption
Configuration Utility software
1M
15

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2001:10:18 11:19:52+08:00
Modify Date                     : 2001:10:24 15:08:08+08:00
Page Count                      : 15
Creation Date                   : 2001:10:18 03:19:52Z
Mod Date                        : 2001:10:18 03:19:52Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Owen Chen
Metadata Date                   : 2001:10:18 03:19:52Z
Creator                         : Owen Chen
Title                           : Microsoft Word - WU210P quick start manaul.doc

EXIF Metadata provided by EXIF.tools