Remotesolution RC96B REMOTE CONTROL UNIT User Manual RC96B Manual

Remote Solution Co., Ltd. REMOTE CONTROL UNIT RC96B Manual

User Manual

Download: Remotesolution RC96B REMOTE CONTROL UNIT User Manual RC96B    Manual
Mirror Download [FCC.gov]Remotesolution RC96B REMOTE CONTROL UNIT User Manual RC96B    Manual
Document ID3970299
Application ID99uE6XF5ddFeUxMPRyXNEg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize5.59kB (69866 bits)
Date Submitted2018-08-21 00:00:00
Date Available2018-08-21 00:00:00
Creation Date2018-08-21 09:18:43
Producing SoftwarePDFCreator 2.4.1.13
Document Lastmod2018-08-21 09:18:43
Document TitleRC96B Manual
Document CreatorPDFCreator 2.4.1.13
Document Author: shirleywang

RemoteSolution Co. Ltd,
1.
Application Processor
1.1. GP565
2.
Application Device
2.1. TV(U/R), STB
3.
Application KEY
3.1.
3.2.
Remote Controller Unit
TV key
TV Power, Vol+/-, Mute, Input S 5 keys
STB Key
STB Power, Google, Page up/down, Live, Vol+/-, Mute, Recent, Ch+/-, Backward, Menu, Guide, Up,
Down, Left, Right, OK, Shows, Movies, Search, REC, REW, Play/Pause, FF, 0~9(Digit), Set S 37keys
4.
LED
4.1. Green LED : RF Check output signal and enter setting mode ON/OFF
4.2. Red LED : Confirm for IR output signal & Confirm the detection of Low battery signal.
4.3. Back-Light : Turns on when there is movement on the remote control SFade out off after 3 seconds
5.
Main Function
5.1.
5.2.
5.3.
5.4.
5.5.
5.6.
5.7.
5.8.
5.9.
5.10.
5.11.
5.12.
5.13.
5Digit Code Entry.
Auto-Search.
RF Pairing
RF Un-Pairing
Battery Monitor
Low battery detection
Couch Function
IR Un-Pairing
Version Out
Device Volume Setting
RF Information
Key function table
Factory Reset
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
2/6 page
RemoteSolution Co. Ltd,
1.
Remote Controller Unit
Code Entry Method
The function is set by inputting 5-digit CODE to Device for each manufacturer.
How to enter set-up Mode?
*Press and hold the setting key for 3 seconds until Red is changed to Green LED € Enter Setting Mode.
1.1.
UR Setting (TV).
1.1.1. Enter Setting Mode.
1.1.2. When the 5-digit entered in the brand list is present in the DB, the green LED turns off after blinking
twice.
1.1.3. If invalid Digit input is entered, Red LED and Green LED are blinked one time in sequence and then
turned off.
1.2. When the UR setting is completed, TV Power, Vol+/-, Mute, Source key are sent in UR Code.
2. Auto-Search Method
This function searches DB of Device by [CH+] or [CH-] key in turn, finds the setting numbers of the device, and
sets remote.
2.1.
2.2.
2.3.
Enter the setting mode.
Press [9][9][1] sequentially to turn off the Green LED after blinking twice.
Enter the [CH+] or [CH-] key.
2.3.1. 3-Frame Power Code is output by [CH +] or [CH -] key input.
2.4. If the desired code is searched, enter the [OK] key.
2.4.1. Save the searched code and exit the setting mode after Green LED blinking twice.
2.5. If there is no key input for 10 seconds before [OK] key is input, Red LED and Green LED are turned off
after blinking one time in sequence, leaving setting mode
3.
RF Pairing
This function is to transmit the key data of the cable device through RF
3.1. Process
3.1.1. Enter the setting mode
3.1.2. If you press [MENU] key, Green LED blinks and enters Discovery mode.
3.1.3. Check the 3-digit validation code on the STB screen and enter it with the remote control.
3.1.4. If the pairing is completed normally with entered input, the Green LED turns off after blinking twice.
3.2. Sending Data
3.2.1. When the pairing is completed, all the key data related to STB transmit through RF.
3.2.2. TV key data transmit through IR.
4.
RF Un-Pairing
This function is to cancel the pairing between the STB and the remote control.
4.1 Enter the setting mode.
4.2 If you press [9][8][7], Green LED will blink twice with un-pairing.
3/6 page
RemoteSolution Co. Ltd,
5.
Remote Controller Unit
Battery Monitor
This function is to check battery status.
5.1 Enter the setting mode.
5.2 Press [9][9][9], and check the LED status.
5.2.1. If the Green LED blinks 4 times, battery status is excellent.
5.2.2. If the Green LED blinks 3 times, battery status is good.
5.2.3. If the Red LED blinks 2 times, battery status is low.
5.2.4. If the Red LED blinks 1 times, battery status is very low.(should be replace)
6.
Low Battery Detection
This function blinks the Red LED 5 times, each time the key is pressed and released when the battery voltage is
below 2.4V.
7.
Couch Function
This function is to stop the IR output to reduce the battery consumption when any key is pressed for 30 seconds
continuously.
8.
IR Un-Pairing
This function is to switch the set TV key to the default state.
8.1. Enter the setting mode.
8.2. Press [9][8][6], and the Green LED blinks 2 times with IR Un-Pairing.
9.
Version Out
This function outputs 4-digit version of the remote control through LED.
9.1. Enter setting mode.
9.2. Press [9][8][3], the Green LED blinks 2 times.
9.3. Press [1] and check Red LED blink count
9.4. Press [2] and check Red LED blink count
9.5. Press [3] and check Red LED blink count
9.6. Press [4] and check Red LED blink count.
9.7. Red LED and Green LED sequentially blink 1 time and turn off. Finally setting mode is exited.
9.8. Example,
9.8.1. Press [1], Red LED blink 1 time.
9.8.2. Press [2], Red LED blink 8 times
9.8.3. Press [3], Red LED blink 1 times
9.8.4. Press [4], Red LED blink 0 times
9.8.5. Then, Remote version is 1.8.1.0.
10. Device Volume Setting
This function switches the Vol +/-, Mute Key to TV volume control or STB volume control mode.
10.1. TV Volume Control Mode
10.1.1. Enter setting mode
10.1.2. Press [Vol+] key and Green LED blinks 2 times and it switch to TV Volume control mode.
10.2. STB Volume Control Mode(Default)
10.2.1. Enter Setting Mode
10.2.2. Press [Vol-] key and Green LED blinks 2 times and it switch to STB Volume control mode.
4/6 page
RemoteSolution Co. Ltd,
Remote Controller Unit
11. RF Information
Vendor ID
Vendor String
User String
Device Type
Profile ID
0x10D0
KAON
RC96B
0x01
0x01
12. Key Function Table
MODEL
FORMAT
DUTY
CARRIER
LEAD
BIT "0"
BIT "1"
1st WORD
2nd WORD
Repeat
Custom
NO
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
Function
TV Power
Input
STB Power
Google
Page Up
Page Down
Live
Vol+
VolMute
Last
Ch+
ChBackward
Menu
Guide
Up
Down
Left
Right
OK
Shows
Movies
Search
REC
REW
Play/pause
FF
Set
RC96B(KUR1)
Nec (Lead + Custom(16) + Data(8) + Data_Bar(8) + End)
1/2
37.9 KHz
9.0 / 4.5 ms
0.56 / 0.56 ms
0.56 / 1.69 ms
108ms
108ms (Simple Repeat)
9.0 / 2.25 / 0.56 ms
C96A (h)
Data (IR)
Data (RF)
TV code
TV code
6B (h)
6B (h)
77 (h)
77 (h)
37 (h)
37 (h)
38 (h)
38 (h)
78 (h)
78 (h)
41 (h)
41 (h)
42 (h)
42 (h)
43 (h)
43 (h)
32 (h)
32 (h)
30 (h)
30 (h)
31 (h)
31 (h)
4C (h)
4C (h)
09 (h)
09 (h)
53 (h)
53 (h)
01 (h)
01 (h)
02 (h)
02 (h)
03 (h)
03 (h)
04 (h)
04 (h)
00 (h)
00 (h)
79 (h)
79 (h)
52 (h)
52 (h)
3C (h)
3C (h)
47 (h)
47 (h)
48 (h)
48 (h)
61 (h)
61 (h)
49 (h)
49 (h)
21 (h)
21 (h)
22 (h)
22 (h)
23 (h)
23 (h)
24 (h)
24 (h)
25 (h)
25 (h)
26 (h)
26 (h)
27 (h)
27 (h)
28 (h)
28 (h)
29 (h)
29 (h)
20 (h)
20 (h)
TV
5/6 page
RemoteSolution Co. Ltd,
Remote Controller Unit
13. Factory Default
This function clears all data that is currently set, and then returns to the factory default state.
13.1. Enter setting mode
13.2. Press [9][8][1] and Green LED blinks 2 times. All data set in the RAM and Flash area is switched to
factory default.
* The Above soft specification may change later
-END-
6/6 page

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2018:08:21 09:18:43+08:00
Modify Date                     : 2018:08:21 09:18:43+08:00
Author                          : shirleywang
Subject                         : 
Page Count                      : 6
Page Layout                     : SinglePage
Page Mode                       : UseNone
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:a4a827af-a73b-11e8-0000-6fb49d8d67bf
Producer                        : PDFCreator 2.4.1.13
Keywords                        : 
Creator Tool                    : PDFCreator 2.4.1.13
Document ID                     : uuid:a4a827af-a73b-11e8-0000-6fb49d8d67bf
Format                          : application/pdf
Title                           : RC96B Manual
Creator                         : shirleywang
Description                     : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: TX4RC96B

Navigation menu