Renesas M16C 30P Users Manual M3062PT2 EPB User's

2015-02-06

• Preface
• Important
• Precautions for Safety
• Contents
• User Registration
• Terminology
• 1. Outline
  • 1.1 Package Components
  • 1.2 Other Tool Products Required for Development
  • 1.3 System Configuration
    • 1.3.1 System Configuration
    • 1.3.2 Names and Functions of the PC7501 Upper Panel LEDs
  • 1.4 Specifications
  • 1.5 Operating Environment
• 2. Setup
  • 2.1 Flowchart of Starting Up the Emulator
  • 2.2 Installing the Emulator Debugger (M16C R8C PC7501 Emulator Debugger)
    • 2.2.1 Installing the Emulator Debugger
  • 2.3 Connecting the Host Machine
  • 2.4 Connecting the PC7501
    • Cautions for Connecting the PC7501:
  • 2.5 Connecting the Power Supply for the Emulator
    • Cautions for AC Adapter:
  • 2.6 Turning ON the Power
    • 2.6.1 Checking the Connections of the Emulator System
    • 2.6.2 Turning ON/OFF the Power
      • Notes on Power Supply:
    • 2.6.3 LED Display When the Emulator Starts Up Normally
  • 2.7 Downloading Firmware
    • 2.7.1 When It is Necessary to Download Firmware
    • 2.7.2 Downloading Firmware in Maintenance Mode
      • Note on Downloading Firmware:
  • 2.8 Self-check
    • 2.8.1 Self-check Procedure
    • 2.8.2 If an Error is Detected in the Self-check
  • 2.9 Connecting the User System
    • 2.9.1 Connecting to an 80-pin 0.65-mm-pitch Foot Pattern
    • 2.9.2 Connecting to a 100-pin LCC Socket
    • 2.9.3 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1)
    • 2.9.4 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2)
    • 2.9.5 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3)
    • 2.9.6 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 4)
    • 2.9.7 Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 1)
    • 2.9.8 Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 2)
    • 2.9.9 Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 3)
    • 2.9.10 Connecting to a 128-pin 0.5-mm-pitch Foot Pattern
  • 2.10 Switch Settings
    • 2.10.1 Switch Settings of the JP1
  • 2.10.2 A/D Conversion Bypass Capacitors
  • 2.10.3 Pullup of Emulation Ports
  • 2.11 Selecting Clock Supply
    • 2.11.1 Clocks
    • 2.11.2 Using an Internal Oscillator Circuit Board
    • 2.11.3 Using the Oscillator Circuit on the User System
    • 2.11.4 Using the Internal Generator Circuit
• 3. Usage (How to Use the Emulator Debugger)
  • 3.1 Starting Up the Emulator Debugger
    • 3.1.1 INIT Dialog Box
    • 3.1.2 MCU Setting Dialog Box
    • 3.1.3 Checking Connections of the Emulator System
  • 3.2 Editor (Source) Window
  • 3.3 Hardware Breakpoint Setting Window
  • 3.4 Trace Window
  • 3.5 RAM Monitor Window
• 4. Hardware Specifications
  • 4.1 Target MCU Specifications
  • 4.2 Access Timing
    • 4.2.1 Operation Timing of Memory Expansion Mode and Microprocessor Mode (Vcc1=Vcc2=5V)
    • 4.2.2 Operation Timing of Memory Expansion Mode and Microprocessor Mode (Vcc1=Vcc2=3V)
  • 4.3 Differences between the Actual MCU and Emulator
  • 4.4 Connection Diagrams
  • 4.5 External Dimensions
    • 4.5.1 External Dimensions of the Emulation Probe
    • 4.5.2 External Dimensions of the M30800T-PTC
  • 4.6 Notes on Using This Product
• 5. Troubleshooting
  • 5.1 Flowchart to Remedy the Troubles
  • 5.2 When the Emulator Debugger Does Not Start Up Properly
  • 5.3 How to Request for Support
• 6. Maintenance and Guarantee
  • 6.1 User Registration
  • 6.2 Maintenance
  • 6.3 Guarantee
  • 6.4 Repair Provisions
  • 6.5 How to Make Request for Repair