Repeater Technologies OA850C One or two channel bi-directional repeater User Manual 8
Repeater Technologies Inc One or two channel bi-directional repeater 8
8
Preliminary Draft - HTI confidanlial OA850C NR Operations Manual DRAFT 550-4999—01 Revision A September 1998 1150 Morse Avenue - Sunnyvale, 044940894505 - USA - Tel: +1 408 747-1500 ' Fax:+1 408 747-0375 Preliminary Dmfl a HTI Confidential 01993 Repeater Technologies. Inc. All rights reserved. a All figures, tables, and text In this manual are the property of Repeater Technologies, Inc. This manual provides product, ordering, installation. testing, maintenance, and application intorrnatlon for this product. This information is confidential: any unauthorized duplication. distribution or electronic transfer of the materials to anyone other than Repeater Technologies' authorized employees is forbidden. By accepting this operations manual from Repeater Technologies. you agree to hold, in strictest confidence the materials and Intonnatlon herein, and not to use or to disclose this fnfonnetion to any person. firm or corporation. without the expres written permission of Repeater Technologies. “Confidential Information” refers to any Repeater Technologies proprietary information, technical data, know-how. product plans. products, services, designs. drawlngs, hardware configuration inforrnetion, end tables featured In this manual. Repeater Technologles, Network Repeater. and RepeaterNet are trademarks of Repeater Technologies. Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. Other brands and their products are trademarks or reglstered trademams of their respective holders. Corporate Hea dquertels 1 150 Morse Avenue 0 Sunnyvale, CA 94303 Tel: (406) 747-1900' (888) 747-1515 (USA and Canada) Domestic Customer Service: (800) 933- 1901 Fax: (408) 747-0875 - wwmrepoaters.cam Mfi—m Preliminaly Drefr- RTI Confidential Contents _____________——————— Chaptert. Overview About This Book.. General Repeater Information . Functional Description Lioensing...... Technical Specrtications Ordering Information" OABSOC NR Configurations and Part Number Optional Equipment Available trom Repeater Technologies Back-up Power System. Accessory Kit Items Ordering Procedure Technical Services.... Contacting Repeater Technologies Chapter 2. Installation Instructions installation Overview ............... Receipt and Inspection of the OABSOC NR . Installation Equipment Site Survey............. Chapter 3. Mounting the Repeater Mounting Associated Equipment Mounting and Connecting Antennas . Wall Mounting Pole Mountin Grounding the Repeate Chapter 4. Powering the OABSOC NR . AC Power Wiring DC Power Wiring Alarm and Control Wiring, Digital Control Outputs . Alarm and Control Relay Outputs Digital inputs ................. External DC lnp ut Voltage Chapter 5. Orienting and Isolating Antenna Preliminary Antenna Orientation BTS Antenna .. Mobile Antenna Antenna Fundamentals Antenna isolation Antenna Orientation an utpu Chapter 5. Completing Install Turning On System Power.. Confirming Proper System Voltage .. Checking that Power Amplifiers are 0 Determining the Correct Frequen Setting the Channel or Band Configuring Gain Initially. Veritying and Optimizingt e o 9 Chapter 7. Maintenance and Troubleshooting Routine Maintenance LEDs ....... Troubleshooting .-. wwmm-uotoooximuiat OABSOC NFI Operations Manual Contents — 3 Preliminary Dralt— FITI Owl/[dermal Internal Backup Battery... Sparing Recommendatio Repair and Return Procedure Product Warranty Glossary Figures Figure 1. OABSOC NR Exterior Front View Figure 2. OAESOC NR Entry Box (AC)... Figure 3. Simplified 1-Chennel OABSOC NR Block agrem—Signal Flow Figure 4. Typical Installation... ....... Figure 5. Mounted Growth Cabinet Example Figure 6. Growth Cabinet Example with BUP - Figure 7. Rear Mounting Bracket..... Figure 8. Rear Mounting Bracket with Unit—Slde Wew . Figure 9. installation of Rear Mounting Bracket on a Wall . Figure 10. Guide Bolt and Slot"... Figure 11. Repeater Mounting and Figure 12. Pole Mounting Hardware Figure 13. Pole Mount—Side View Figure 14. Typical System Ground .26 Figure 15. Power Features.... .27 Figure 16. OABSOC NR to BUPS-25/80 Wiring Kit .29 Figure 17. Customer UPS, I/O Alarm and Monitoring Termrnal Blocks .29 Figure 18. Typical Digital Output Applications . 31 .32 Figure 19. Typical Relay Appllcations...... Figure 20. Typical Digital Input Applications figure 21. Typical PA Disable Input . Figure 22. Typical DC Monitoring App | Tables Table 1. Models and Frequency Range 9 Table 2. Electrical Characteristics 9 Table 3. MechaniceVEIectricaI Characteri ics 9 Table 4. Inputs and Outputs 9 Table 5. Additional Characteristics 9 Table 6. RepeaterNet Alarm, Monitoring, and Control. 10 Table 7. Alternate Power Options. 10 Table 8. Ordering Considerations. 10 Table 9. Configuration and Part Numbers 11 Table 10. Spare Parts and Accessory Items 12 Table 11. Back—up Power System Selection Guide 13 Table 12. Contents of AC and DC Accessory Kits. 13 Table 13. Required Installation Equipment" 16 Table 14. Wiring Harness Input/Output Lead 30 Table 15. Valid CDMA Channel No. to Frequency Cross Reference Chart. 39 Table 16. Descriptions of LED Indicators. Table 17. System Troubleshooting... ' Contents — 4 OAHSOC NR Operabons Manuel Preliminary Draft - RTI Confidential Chapter 1. Overview _______—___—————— About This Book This manual is divided into the following chapters. Chapter 1. Overview (page 5) Includes a general product description, functional description, technical specifications, and ordering information. Chapter 2. Installation Instructions (page 15) Provides overview information about the installation process and equipment. as well as instructions for receipt and inspection of the OABSOC NR. chapter 3. Mounting the OABSOC NH (page 18) Provides the information you need to mount the OASSOC NR. chapter 4. Powering the OABSOC NFi (page 27) Provides information about AC power, DC power, modem, and alarm and control wiring. chapter 5. orienting and Iooleting Antennas (page 35) Provides information about antenna mounting, orientation, and isolation. Chapter 5. Completing Installation (page 38) Provides Information about activating system power, assigning frequency, configuring initial gain, verifying and optimizing coverage area, and configuring for alarm reporting and system operation. Chapter 7. Maintenance and Troubleshooting (page 42) Includes information about the following topics: routine checks required to maintain performance and to address problems, reium and repair of the OAESOC NR, and the product warranty. General Repeater Information The Repeater Technologies Over-the-Alr 8500 Network Repeater” (hereafter referred to as the OABSOC NR or the repeater) is a bi-directional, on-frequency, over»the-air RF channelized Repeater for CDMA. The OABSOC NR extends the coverage of PCS base stations. It is available with an optional diversity receive feature, which improves base station receive performance in high-mobility applications. The repeater receives signals from a Base Transceiver Station (BTS) and re-transmits them to a subscriber Personal Communications Service (PCS) telephone; likewise, the repeater receives signals irom a subscriber telephone and re-transmits them to the BTS. Repeaters significantly improve coverage in areas with weak signal reception or transmission. The OASSOC NR is designed for indoor or outdoor installation and can be either wall or pole mounted. The unit’s compact cabinet simplifies installation, while its aesthetically acceptable design allows it to be zoned easily in many locations. The repeater only requires initialization. Also, as a field- replaceable unit, it requires no component-level repair. OABSGC NR Operations Manual Chapter 1, Overview -— 5 Preliminary Draft - RTI Confl'denlial 16.00 24.00 Figure specific to OMSOC to replace this ilgure. Flgure 1. OAESGC NR Exterlor Front Vlew The repeater oonsists ol the tollowing assemblies: LNA (Low Noise Amplifier) PA (Power Amplifier) Channel Select Filters Diplexers Power Supplies ACU (Alarm and Control Unit) All assemblies are mounted on a heatsink and enclosed in a sealed, painted aluminum, weathertight cabinet. During normal operation, the cabinet housing remains closed. Access to power and to data transmission connections is provided through an Entry Box, which extends trom the bottom of the cabinet. install repeaters and associated hardware in locations suitable for adequate reception of signals from the BTS and tor effective retransmission of these signals to a subscriber. The 0A8500 NF! may be equipped with an optional cellular telephone, which is mounted on the interior of the entry box front door, as shown in the lollowing Entry Box figure. The cellular telephone teature can be used with FlepeaterNet NMS for monitoring a network of repeaters. For more inlonnation, see Repeater/Vet Craft for the OABSGC NH. DDDDDD 043500 NH Operations Manual Chapter 1. OvaM‘ew — 6 Preliminary Dreff— RTV Confidential 1 of 2 IIO Power Switch Craft Port for N Cmflocfifls l l—l Computer to _ d the Rnpnmr J‘ —77 Main Power 0 Termlnll ' 0 Block :: ellular‘ I PM“ OABSOOlpecllic figure to replace this Hours, 0 O 0 Q Figure 2. 045500 NR Entry Box (Ac) Functional Description The OABSOC NR uses e unique lntennediate Frequency (lF) filtering design to achieve a high degree of selectivity. It also uses a common local oscillator lor up-end down-conversion to prevent lrequency conversion error. The HepeaterNet Craft software is the configuration management and alarm monitoring interface for the OABSOC NH. The repeater has two communication (COM) ports tor FlepeaterNet connections—a serial port for direct. laptop connections and a modern port for remote connections. An Automatic Level Control (ALC) circuit protects the repeaters circuitry trom potentially damaging high input levels and minimlzes the generation of lntermoduialion Distortion (IMD) in the transmit power amplifier. The lollowing figure is a block diagram of the OABSDC NH. The signal processing flow through the repeater in the lorward direction (BTS to mobile) is similar to the flow in the reverse direction (mobile to BTS). 0148500 NH Operations Manual Chapter 1. Overview — 7 Preliminary Dru/f — RTI Confidential FORWARD snow “19me 55; BPF FORWARD END p‘ ‘ REVERSE PA mom END MOBILE, mvsnsn’v gram to rupla this flgure. DIVERSITY RECEIVE ctncun‘flv Flgure 3. Simplified 1-Cfiannel OAGSDC NH Block Dlayram—Slgnal Flow Signal flow is as follows: 1, The received signal from the BTS antenna enters the repeater through the cabinet-mounted Type N (f) connector, and feeds to a branching simulator and a diplexer filter. The signal then is amplified by an LNA and down-convened to an Intermediate Frequency (IF). 3. After being filtered by Surface Acoustic Wave (SAW) filters, the output signal is up—converted and precisely restored to the original RF frequency by using the same Local Oscillator (L0) as the one in the down-convener. 4. The signal then passes through a bandpass filter to eliminate unwanted sidebands and L0 leakage. 5. The transmit powervamplifier further amplifies the signal to achieve final transmit Radio Frequency (RF) power levels. See Table 2 for specific information about power output. 6. The signal finally routes through the output diplexer to the mobile antenna. (The diplexers permit use of common antennas for both transmit and receive signals while effectlvely separating the receive band from the transmit band.) Licensing All owners of the OA8500 NR should consult with the appropriate local and national agencies for information on licensing. OABSOC NH Operations Manual Chapter 1. Overview - 8 Preliminary Draft? RT! Confidential fechnical Specifications Table 1. Models and Frequency Range MODELS Nut) rREQUE NC‘.‘ RANHF (MHz) FORWW mam-mm mums-w.» Table 2. Electric-I cmracterislics [ LECTWK‘AL (1me IERI5TICS RFOU'I’PUTPOWER FER CmER ATM MINA PORT “— DEWA'HON FACTOR Inn) WAVErDmQUAuTv mm mmcraL. Em: lam/u (,H."\RACT[RISTIC\ INPUTVGLTAGE OPT'IOIG m-Ix min-mam.) MxmeMm) 0148500 NR Operations Manual Chapter 1. Overview— 9 Preliminary Draft — RTI Confidential Table 6. Hepeatemet Alarm, Monltorlng, and Control AU r RNA | I: POWER nu | IONS mm m u hwr: dbuiwp polar washout AC m wrrnomiurg) m rum-ted Mn. m ban-nu Hybrid Sch! and "rec. w with ennui eleflriz prom. pnenflen usimn Ordering Information Consider the following requirements when ordering the meme NFt. Table 3. Ordering Canslderatlone Requlrement AC or DC. power cord. watertight conduit or connector. A power supply in case at interrupted electrical service; note that a Back- up Power System (BUPS) is available lrom Repeater Technologies. What types are required; what is the intended system coverage. Note that antennas are available lrom Repeater Technologies. What type and length are requiredt Note that coaxial cable is available horn Repeater Technologies. Special requirements forthe repeater and antennas. Type N to ’I|5 DIN Jumper Cables I Item Electrical Power Back—up Power Antennas. Donor or Subecrlher Coexlal Cabling Mounting Antenna Interface Connectors 0A8500 NH Operations Manual Chapter 1. Overview— 10 Preliminary Draft - HT! Confidential OABSOC NR Conflguratlons and Part Numbers Tabla 9. Configuration and Fun Numbers Band No. of Voltage Dive/sky Part Number channels 1 1151230 VAC yes 090-3100-01 1 1151230 VAC no 090310003 1 +24 was yes 090-3100- A 1 +24 VDC no 090-31 -07 2 115/230 VAC no 090- 00-04 2 +24 VDC yes 0 («1100-06 1 115/230 VAC yes 0311001 1 115/230 VAC no 090311003 1 +24 me yes 090311005 5 1 5' +24 was no 090311007 2 115/230 we no 090311004 2 +24 VDC yes 090311005 1 1157230 VAC yes 090-3120-01 1 1 15/230 VAC 090312003 1 +24 VDC yes | 0904112005 c 1 +24 vnc no | 0903120207 2 115/230 VAC no | 090312004 2 +24 VDC yes 090312006 1 115/230 VA yes 090313001 1 115/230 v no 090313003 1 +24 v c yes 090313005 D 1 +2 DC no 090313007 2 11 230 VAC no 090313004 2 +24 VDC yes 090-3130-06 1 115/230 VAC yes 090314001 1 115/230 VAC no 09043140413 1 +24 VDC yes 090314005 E 1 +24 VDC no 090314007 115/230 VAC no 090314004 2 +24 VDC 5 090314006 1 1151230 VAC yes 090315001 1 115/230 VAc no 090315003 1 +24 VDC yes 090-3150-05 F 1 +24 we no 090315007 2 115/230 VAC no 090-3150—04 2 +24 VDC yes 090-3150—06 1 OABSDC NH Operations Manual Chapter 1. (We/view — 11 Preliminary DIE/t - HTI Confidential Optional Equipment Available from Repeater Technologies Table 10. Spare Parts and Accessory Items Description Part Number I Antennas“ Call tor inlormalion. Connectors Call tor information Coaxial Cable Call lor information Power Cord 103-0137-01 I Solar Shields To be announced. Pole Mounting Kit 137-0438-01 McMaster-Carr 54-ineh Banding Kll Pan No. 5655K12. MchslbfiGa/r Supply Co, ’ Los Ange/es, CA, USA” Tel, #(562) 592-6911) Cabinet Door 024-0976-02 ' ' I/O Entry Box with Cover _ J24400401 V0 Box Cover Gasket 022-012002 l/O Box Gasket 022~0121-01 Intemal Lead Acid Back-up Battery , 149-0652-01 PC Interface Cable DES 9~Pin Fomale-to-Female 157-0713-01 Modem Module 037-1524-01 _‘ Wireless lnterlece Cable 187-0877-01 Wirelese Antenna V0 - N(F) to SMA(F) Bulk head adapter 142-0521-01 connectlon 800 MHz Mag Mount Antenna for Wireless V0, 6’ cable 149-0934-01 with N(M) connector 1 4941924-01 Cellular Phone (OH-1430) EUPS-25/40 250-1103—02 BUPS-ZS/BO 250-101 107 Surge Protector - N(M) to N(F) Lightening 1490932-01 Operations Manual (Hard Cow) 550-3100-01 Operations Manual (CD-ROM) To be announced, Alarm, Power, and Growth Cabinet Button Plugs 137-0446-01 Conduit Fitting 137-0447-01 Back Mounting Plate 020422903 Stainless Steel 3/5" Locking Washer 125005907 Stainless Steel ’r.' x 1" Flat Washer 125-0065—07 Stainless Steel Pin-in Head Security Bolts m Stainless Steel Hex Heed Bit Pin-in Head, 7/34 1290007438 Door Hinge Set 137-0428r01 Allen Wrench 129-0007-02 HepeaterNet NMS Craft Software 519-1200-03 BUPS Power & Alarm Cable Assy (Kit) 187-0135-01 ‘Typical antennas include parabolic reflectors, comer reflectors, circular, linear, directional oo-linears, cross or slant polarization, lag periodic array, or Yogi. OABSOC NR Operations Manual Chapter 1. Overview — 12 Preliminary Draft - H7! Confidential Back-up Power System To select a BUPS (Backup Power System) tor your application, match the repeater you are using with the amount of back-up time required. Table 1 1. Back-up Power System Selection Guide Back-up Hours Power calculated Product Consumptlon Current slips-25140 BUPs-zsrao Model Number 0 24 We 0 24 Vdc 25 A 40 A-H 25 A 80 A-H 0A8500§=3~Wum 1-channel “(W 3.1 OABSOC Growth Cabinetfirfl-Walt, Zchennel‘ M/ ‘Grawth cabinet power (2'“’ channel power) is the sum of the Repeater plus the growth cabinet: 310 W + 260 W = 570 W. Accessory Kit Items Table 12. Contents MAC and or: Accessory Klts Ac Accessory Kit (PIN oer-0195411) Dc Accessory Kit (PIN 091-0105-02) Items | Quantity Items Quantity Power Cord 1 each BUPS Powr and Alarm Cable 1 each Assembly Wrench. Hex Key (Allen Wrench) 1 each Wrench. Hex Key (Allen Wrench) PC Interface Cable QB-D-SUB/BP- 1 each PC Interface Cable QB-D-SUB/BP- SUB SUE Hex Bit, Pin-in-Socket, 7/32 | 1 each Hex Bit, Pin-in-Socket, 7/32 1 each Alarm, Power, and Growth Cabinet | 4 each Alarm, Power. and Growth Cabinet 4 each Button Plugs Button Plugs Conduit Fitting 4 each Conduit Fitting 4 each Operations Manual (Hard Com!) 1 each Operations Manual (Hard cow) 1 each HepeaterNeI Cratt Software 1 disk FlepeaterNel Craft Software 1 disk Ordering Procedure When ordering, specify a shipping destination and a billing address. Repeater Technologies will return an order acknowledgment with the scheduled shipping date. Each shipment includes an equipment list showing the equipment ordered and shipped, including details about system and equipment options. Contact the Repeater Technologies Sales Department for ordering iniormatlon. Technical Services Repeater Technologies otters technical services to supplement the manpower resources oi its customers. Quotations for the following services are available upon request. Site and construction surveys Network design Design verification Training Installation Accessories (antennas, coaxial cabling, and so on) EIEIDDCID OABSOC NFI Operations Manual Chapler 1. Overview - 13 Prsllmlnaly Draft 4 RTI can finish Hal Contacting Repeater Technologies Contact the Repeater Technologies corporate headquansrs for sales information or technical assistance for the OABEDC NR, or lor any other cl our communications or related products. Carporals Headquarters 1150 Morse Avenue Sunnyvale, CA 94089-1605 USA Tel: (408) 747-1900 (886) 747-1515 (USA and Canada) Fax: (408) 747-0375 Web: ~ www.repealers.com Customer Servlce Tel: (408) 747-1946 " (800) 928-1901 (USA and Canada) 048500 NFl Operations Manual Chapter 1. Overview- 14 Preliminary Dmlf— HT! Can/idenlial Chapter 2. Installation Instructions Installation Overview The OABSOC NR is designed lor indoor or outdoor installation and can be either wall-mounted or pole-mounted. The unit's oompact cabinet simplilies installation, While its aesthetically acceptable design allows it to be easily zoned in many locations Because the RepeaterNet Craft soltware is used during the physical installation of the repeater. pre- load the Craft software on the laptop computer to be used at the installation site. See Repeateret Craft lor the OABSDC NFtlor information about installing and using RepeaterNet. Bring a 03-9 cable to the installation site to connect your laptop with the repeater, NOTE: Only qualified serw‘ce or technical personnel should install the OABSOC NFl. See the following illustration oi atypical repeater installation with installed components. Suburlbll I Mobile! Hbfild AMI-rm. _ Donorl Cell sit- Antenn- Coll Jump-r Symm Ground Telephone Lln' (It nppllelblo) DC PW“ AC Power or auPs (opllonll) Figure 4. Typical Installation OA8500 NR Operations Manual Chapterz. installation Instructions —- 15 Preliminary Draft — RTl Confidential Receipt and inspection of the 0A85OC NR Inspect the OASSOC NFt for damage immediately upon receipt: note any damage on the waybili, Be sure to request that the delivery agent sign the waybill for verification. Should damage be found: a Notify the transfer company as soon as possible 0 Submit a damage report to the carrier n Inform the Field Services Department of Repeater Technologies in writing NOTE: save original shipping carton and packing materials‘for any future transport of the unit. Alter unpacking the equipment, inventory the contents against the packing lists. inspect the unit thoroughly for damage hidden by the packaging, paying particular attention to the following: D Bent or dented sheet metal D Loose or broken components ct Damaged connectors . . U Damaged or broken wiring or coaxial cables Also, inspect the contents oi the'aocessory kit and any optional equipment ordered with the unit. Installation Equipment See the following table for a list of required installation equipment. Additional equipment could be needed, depending upon specific installation site requirements and optional accessories ordered. NOTE: The Path Data Sheet and site plan are needed during installation to define the intended parametem of the project, including coverage area, gain settings. and antenna location. if necessary, consult a network administrator for more Information. ,\ Table 13. Required Installation Equipment To: Correctly configure the repeater to operate in the PCS network Detach security screws Use thls equlpment: Site Plan/Network Engineering documentatlon Ratchet or Hex Screwdriver for 7/32 Pln~in~ Socket Driver Volfmeter, Fluke 75' Spectrum Analyzer HP 8591 Cellular Service Monitor with Signal Generator. |FR~1500, HP-8594A‘ Type N (m) 50-ohm Termination. 20 WI (2 ea) Mounting Hardware Electrical Wiring Equipment (as needed) Laptop Computer (with RepeaterNet installed) Accessory Kit Pole Mounting Kit and Tightening/Crimping Tool (tor pole mounting only) ‘Equivelent substimte can be used. Test power connections and analog test points Test power output Test antenna Isolation and repeater power Terminate antenna ports during oft-air test Mount repeater and antennas Connect external systems to input and output connectors Control and monilor the repeater Mount and Install the repeater Mount the repeater to a pole and secure pole mounting straps OABSOC NH Operab'ons Manual Chapterz. installation lnstmciions — 16 Preliminary Draft — RTI Confidential Site Survey Review the installation site thoroughly belore mounting antennas or the OABSOC NR. Site review should include, but not necessarily be limited to: Weather Determine whether environmental conditions necessitate special shielding oi the Repeater or other equipment. Security Determine whether some type of barrier is needed to protect equipment and whether a security light is required. Optlorial Site Equipment Determine whether additional site equipment, such as a pump. generator, or light is required. if so, where is the equipment to be located, and are special enclosures lor any equipment required. erlng and Wiring Access > Determine any special wiring requirements cablnet Access Determine whether there is enough room for the repeater door to open once mounted. CAUTION: In an extremely hot environment, such as a desert, shading from direct sunlight may be necessary to prevent the repeater and associated equipment from overheating. OAHSDC NR Operations Manual Chapter 2. Installation Instructions — 17 Preliminary Draft - RTI Confidential Chapter 3. Mounting the Repeater « Mounting Associated Equipment Mount me OABSOG NFl assembly antennas, antenna coaxial cabling, and BUPS (it used) balore mounting and wiring the repeater. If you intend to add a second irequency channel, you will need to install a growth cabinet to house the second channel. Be sure to allow enough space either above or to the right of the repeater for mounting; examples are shown in the iollowlng figure. Growth Cablnet Figure 5. Mounted Growth cabinet Examples 0148600 NH Operations Manual Chapter St Mounting the OA85OC NH — 1B Preliminary Draitv RTl Confidential Suggested Minimum BUPS-25IM ( Backup Power system ) Figure 6. Growth Cabinet Example with BUPS-25/Ba Mounting and Connecting Antennas Antenna size is specified on the Path Data Sheet—do not install antennas of a different size. The size oi antenna coaxial cabling tor an application depends upon a number of system parameters including, but not limited to: D Required signal output D Antenna gain 0 Transmission line length The allowable path loss for antenna cabling, and therelore the size at the cabling, is specified on the Path Data Sheet tor the project. Do not install cabling of a diflerent size than specified on the Path Data Sheet. ____________.__————————v NOTES: a As a signal passes through coaxial cable, the strength at that signal decreases. This loss of signal strength, known as path loss, decreases as the diameter at the cable increases a Check the diameter of the coaxial cable befare installing. If the cable is more than Ié-lnch (1.3 cm) in diameter, attach a coaxial jumper assembly (which you must supply) to the connector on the antenna cable. Make the jumper assembly of 14-inch (1,3 cm) coaxial cabling and use 7)“ DIN or a Type N connector, one male and one female. __________——__——————~ OABSGC NH Operations Manual Chapter 8. Mounting the OABSOC NR — 19 Preliminary Draft - HT! Confidential To install coaxial cabling to the Base and Mobile antennas: 1. Make sure the coaxial cable is long enough to reach the 0A8500 NR installation site. 2. Install either a 7/is DIN (m) or a Type N (m) connector on the coaxial cable. 3. Connect cables to the Base and Mobile antennas. CAUTION: If a coaxial cable is larger than 16-inch ( 1.3 cm) in diameter, do not connect it directly to an antenna port on the repeater, as possible damage could result. Using a coaxial jumper assembly reduces strain on equipment connectors. 4. Having read the above caution, connect the other end 01 the antenna cables to the appropriate ports labeled on the bottom of the repeater. You can mount the OABSOC NR on a pole or on the wall of a building. The 0A8500 NFt is shipped with the rear mounting bracket attached to the unit. The following figure illustrates the bracket with dimensions. »- 0.375 0.325 1.25 2X 15.” 2X 1150 '—‘ 1.93 10400 13.78 Flgure 7. Hour Mountlng Bracket OABSOC NH Operations Manual Chapter 3. Mounting the 0448500 NF! —20 Preliminary Draft — RYI Confidsflflfil ' The following figure shows a side view of the OAESOC NR and the rear mounting bracket. r—tr" Rear Mounting Bracket Guide Bali and Slot Security Bolts (T emper Proof) Figure 3. Hear Mounting Bracket with Unit—Side View Wall Mounting Wall mounting hardware, which can be ordered from Repeater Technologies, oontains the following: D Four (4) leg bolts 0 Four (4) flat washers a Four (4) lock (split) washers To mount the CABSOC NR on a wall: 1. Separate the rear mounting bracket from the Repeater by removing the attachment bolts and washers (uslng a ratchet or hex screwdriver and the 7/32 pin-in-sockel driver provided in the accessory kit). 2 Using the mounting hardware, secure the bracket to a wall—see the iollowing figure. 048500 NFI Operations Manual Chapter 3. Mounting the OABSGC NR -21 Preliminary Draft A H Ti Confidenlia/ cf/ ‘ ‘ / 4x Flat Washer 4X Lock Washar 4X Boll Figure 9. Installation of Ru! Maunll‘ng Bracket an a Wall sliding the guide ball into lhe guide slot, then replace the Set the repeater into the bracket by 1—see the following two figuresr attachment bolts and washers removed in Step Gulda Ball and Slnl Figure 10. Guide Bart and Slot OABSOC NH Oparaflorls Manual Chapter 3. Mauming the OAHSOC NR —22 Preliminary Drall —- RTI Confidential 4X Lock Washer 4X Flat Washer Figure 1 1. Repeater Mounting and Hardware Placement Pole Mounting Repeater Technologiesvollers optional pole mounting equipment for the OABSOC NR, available when ordering the OABSOC NH. Pole installation requires the following materials: a Pole mounting kit (available from Repeater Technologies) ct Banding kit (purchased separately; available lrom McMaster~Cerr) it you are mounting the repeater on a concrete or metal pole a Class A - Pole Line Hardware it you are bolting the Pole Mounting Bracket to a wood pole The Pole Mounting Channel is designed so that the repeater is “squarely" mounted on the pole and does not wobble. if a concrete pole is used as the mounting structure. typically it is not prudent to try and drill a hole through its center. Similarly, because metal poles may have cable run up the center, drilling is not recommended. Banding is preferred over drilling. However, wood telephone~type poles are forgiving and the pole-mounting channel can be easily fastened to the pole with lag screws or through-pole boltst OABEOC NFl Operations Manual Chapters. Mounting the 048506 NH —23 Preliminary URI/t — HT! Confidenfial (Class A Pole - Line Hardware is a telephone term that specifies bolts and screws that have a heavy electro-galvanized plating so they do not rust.) This type at ruggedized hardware typically is available ircm distributors such as Garybar Electric, ALLTEL Supply, Spring-North Supply, PowerTeI Supply, and so on. This hardware is also available from antenna suppliers and tower erector companies.) The following table describes the Pole Mounting and Banding Kits. Because the Banding Kit comes with 100 feet of band, you need not purchase a kit with every repeater. Pale Mounting Kit (0914721501) Pole Mounting Channel Bolts _J Lock (Split) Washers Flat Washers Tapered Plug, .312D Hole W—Inch Bandlng Klt (Parr No. 5558K 12) (Manuela-fin” Supply Co., Los Angela, CA, USA, Tel. 5 (562) 651-6911) Tightening-Crimping Tool M-Inch. Type‘201 Stainless Steel Band Stainless Steel Buckles J Stainless Steel Scru-Lockt Buckles Carrying Case NOTE: Two people are required for pole mounting To mount the OABSDC NH to a pole: 1. Remove the attachment bohs and washers, then separate the rear mounting bracket from the repeater. 2. Using the hardware provided with the accessory kit, secure the rear mounting bracket to the two (2) pole brackets—see Figure 12 on page 25. 3. Insert the 4 plugs provided into the 4 cuter holes in the rear mounting bracket. 4. Position the rear mounting bracket (with the attached pole channel) against the pole and hold it in place. 5. While one person holds the rear mounting bracket in place, the second person installs the steel bands that hold the bracket against the pole. Consult the manufacturer’s instructions included with the Banding Kit for this procedure. 6. Set the repeater into the bracket by sliding the guide bolt into the guide “slot. 7. Secure the repeater to the bracket with the security screws and washers removed in Step 1. 045500 NR Operations Manual Chapters. Mounting the OA8500 NH —24 Praliminary Draft— HT! Confidential Two 7 " dll. holes for 314" In: ofthm-pult ham _’ Pole Mountlng Chanml H /‘ 4 x Flaw-1h" " 4 x Lock Washer A x Bolt FIbure 12‘ Pole Mounting Hardware Llfllng Anllt H°|° 314" Thru-pel- Bolts with Fllt Wuhan and Locking Acre Nut Pal. Mountlng Chmnol Bundlng Strip: Rnpeator Mountlng Bracket —__ — Fole or Man Figure 13. Pal; Mount—Side View 0Assoc NR Operations Manual Chapter 3. Mounting ma 0.43500 NR —25 Preliminary DIE/l — HTI Confiden u‘ai Grounding the Repeater A If detailed grounding information is required, refer to the Repeater Technologies application note, Installation Standards for Grounding Requirements. Contact Repeater Technologies to receive a copy oi this application note. Connect the screw-compression ground lug (located on the left exterior of the Entry Box) to a suitable earth ground (copper ground rod, copper pipe, grounded steel building lrame, or similar ground point) using 2 to 7 mm, No. 6 to 2 AWG, copper wire—see the following figure. CAUTION: Ground all other cabinets, enclosures, antennas, and coaxial cables used for installation to reduce en y damage from a lightning strike or power surge. system Ground Standard Ground Rod, K-lnch diam eter Figure 14. Typical system Ground 0A 8500 NH Operations Manual Chapter 3. Mounting the OABSDC NH — 26 MM Preliminary Draft — RTI Confidential Chapter 4. Powering the OA8500 NR The OAHSOC NFl is tactory-coniigured with one of the tollowing AC or DCélutfre) power supplies: D 115 VAC/230 VAC t10°le (available) El 24 VDCM—VDQ—fl 0°/o . , NOTE: When wiring power to the repeater, match the voltage at the repeater to the voltage of the power supply. . AC Power Wiring See the following figure tor the location of power teatures. Note that the AC power cord enters the Entry Box through the left-most conduit and that the free end of the cord is equipped with a a-prong plug. Also. the AC plug used for wiring is shipped connected to the J15 receptacle. .. Pomr 0 0 0 switch on an e e o o 0 an in! ..m o w J. . r. O w r ooooooooooooooo O m n ‘ a: Rmptuol ’ ooonoeooonuoeoo -|. - _ mum when 0 o o Green LED, Power ON Grounding Stud Figure 15. Power Futures To wire the AC power leads to the repeaten 1. Using a medium Phillips head screwdriver, remove the Entry Box access plate located at the front/bottom ol the unit. 2. Feed the open end at the power cord through the Iett-most conduit and into the Entry Box. Note that the color coding of the wires is as follows: White = Neutral NOTE: Check polarity with o Bl!ck = UVE / ”01 voltometer betore erIng. Yellow/Green = Ground 3. Remove the nut trom the grounding stud. 4. Attach the ring lug terminal at the grounding wire to the grounding stud and replace the nut. Tighten the nut until the terminal is secure. 5. Locate the AC plug connected to the Jta receptacle, and note the labels next to the plug: COM (common) designates the location of the neutral wire and HOT designates the location ot the live wire. OABSOC NR Operations Manual Chapter 4. Fowedng the OABSOC NH —27 Preliminary Draft — RT) Confidential 6. Unplug the AC plug from the J18 receptacle and loosen the two end terminal screws. The middle terminal screw is not used. A 7. Insert the Live and Common wires into the proper wire guard receptacles, then tighten the terminal screws to clamp wires. (If necessary, reinsert the AC into the J18 receptacle to determine proper wire locations.) 8. He-insert the wire Ac plug into the J1B receptacle. To connect power: 1. Turn OFF the external power source (the circuit breaker). The power supply should be a luse or circuit breaker rated at 10 amps lor 115 VAC or 7.5 amps for 230 VAC mains. 2. Plug the cord from the conduit into the circuit breaker box (if there is an appropriate outlet). 3. If there is no outlet, cut oil the plug from the power cord and expose the 3 colored leads. Strip about Ya inch (a cm) from the end of each wire. 4. It the leads do not reach to the circuit breaker box, measure and cut wiring to make up the dillerence. Use #14 AWG wi_re lor live and neutral lines, and #10 AWG lor the ground line. 5. Connect the ends at the leads to the appropriate terminals in the circuit breaker box. Match live, neutral, and ground llnes to the correct connections. The color coding of the wires is as lollows: ' Whlte = Neutral NOTE: Check polarity wlth a Black = lee I Hot voltometer belore wiring. Yellow/Green = Ground 6. Wrap any exposed connections with electrical tape to avoid shorts. 7. Neatly arrange or secure and. it necessary, environmentally protect power wiring. CAUTION: Do not activate AC power at this time. Dc Power Wiring The BUPS—zS/élo provides backup DC power to your repeater. The following is a diagram of the OAHSOC Network Repeater to BUPS-ZS/BO Wiring Kit. This diagram, as well as Figure 6. Growth Cahlnet Example wlth BUPs-25180 on page 19, are provlded tor planning purposes. For more information. reter to your BUPS documentation. _\ OABSOC NFl Operations Manual Chapter 4. Powering the 0A55OC NR — 28 fl Preliminary Draft - FlTl Confidential OAI9 Network Repeater to BUPS~25l80 Wiring Kit “I M M ll BUPS-ZSIBD m'l‘lfl'lm" OMSDO NETWORK REPEATEH CHARGER g'mxm 75mm». BLOCKS TERMINAL BLOCK 4 fl pm "I SUM“ ‘ » | - mun-l mm 1 omuu ' a - fllglul mm 2 x - in: anlap' hm- (Multan ‘ I - Dlgl'lxl HIM | s - Dlnhll l'lput z I- PM PA Shillflm MEN 7- HIV“. PA snmum DC vow fl’fl LOW he a 1 — mm! T-mpor Alum (swans-m new An-m) vow , z—mtmwlnymszuml Inpll Amm) CHGH‘ Q 3 — “FEE Ffll Iw (mal llbll Alum) FAIL a I~UPSLWHMVO0II§0 Wm (EXIW‘ Irwin Minn) A: Q s -IJPS ug- nanny volugn hymen-mu lam mm) a i-UPS MW! Fl|lk|p|ll (Emu IMAM“) "l , 7-urssum-1uwn-ny ClumlmthM-ml) 5“ g C—uvssumvycnmlmdld mend) - n. nun-n Ins, 22 AWG sane, l mum Plln. mun-non. 150V - an an}, 1mm mum 6", Cinema. m1- smug-a n-ek u". Gm. Lug - m m" '" mu unnIn-hd In men y-nuw "nap-d. nnnlnll. (Pun cl m m n" Ne.|av—o1»a1.rmru Alum cm- u-mm MAIN Ligand: 0 nc m ‘, mm mAwa 112mm: - — — — a , Chassis Ground and . _— IloAWG am 1 fl .- .- n - 14—- 20 Vdc an common In < no AWG 5 hm ' rape-tar 0mm _. _, a _ a . 3mm ) HAWG SplthTolm, h mm AWG Pin mm. kstrlpp-d‘huk l Tlnud 5' - In" L'qu‘dflgh’ 3 PL fiylcl WW", 1uwfiazlimfl'fl. PVC Insulation, SWV 40 mum and: MRS" MC Fl“ Conduit nun-a, BUPS «m Mppd-bock m mun-mu with "(I SD‘GITOMI. (PIHM H“ PIN ‘IT-GIIC—m. BHPS Mil Alum CIN- Mly Figure 15. 0118500 NH to BUPS-ZSHO Wiring KI? Alarm and Control Wiring Repeater installation continues with alarm and control wiring. The following figure shows l/O terminal block designafionst INIOUT 00000000000000 0 ‘ | [II | USER RELAY ALARM RELAY Figure 17. customer UPS, 110 Alarm and Monltoring Termlnal Blocks OA8500 NH Operations Manual Chapter 4. Powering the 018506 NR — 29 Preliminary Draft — H Ti Confidential ' The next table shows l/O lead descriptions. Table 14, Wiring Harness Input/Output Lead Descriptions I: Block J1 INIOUT JZ UPS J22 Alarm RBIIY J23 User Relay Pin No. I Slgnal Name 1 Digital Output 1 2 Digital Output 2 a DC Voltage Input 4 rgrtel Input 1 5 Digital Input 2 6 Fonrrard PA Shutdown 7 Reverse PA Shutdown 1 External Tamper Input UPS Tamper Input UPS A0 Fall Input UPS Low Battery Voltage Input Ts High Battery Voltage Input UPS Charger Failure Input UPS Summary Normally Closed UPS Summary COM Critical Relay NO Critical Relay COM Critical Relay NO a— Funetlon User Controllable Open Collector Driver User Controllable Open Collector Driver 0—75 V Input Voltage External Input Alarm External Input Alarm External PA Control External PA Control Secondary Door Open External Input Alarm Extemal Input Alarm External Input Alarm External lnpul Alarm Extemal Input Alarm External Input Alarm Protected Ground Normally Open Output Common Input Normally Closed Output Mlnor Relay COM Major Relay N0 Normally Open Output 1 Major Relay COM Common Input Major Flelay NC Normally Closed Output Minor Relay N0 Normally Open Output _, Common Input Minor Relay NC User 1 NO User 1 COM User 1 NC User 2 COM User 2 NC Normally Open Output Normally Closed Output Common Input Normally Closed Output Normally Open Output Normally Closed Output Common Input WARNING: When connecn‘ng wirlng, be sure the wiring assembly is not plugged into the repeater. Digital Control Outputs The OABSOC NR has two di switch Is ON, current flows t totlowing figure. The relere ground). gital outputs, each with one open collector transistor lead. When the output hrough a circuit that includes the open collector transistor output—see the nee ground is any of the panel~mounted screw lugs (repeater cabinet OAasOC NFI Operalions Manual Chaprer4. Powering [he OABSOC NFI — 30 Preliminaly Draft — HTI Confidential (9 :' (-) E Repeater 1/0 Ctnwm Claims +5 V To Digital ' ' To mynl Gilli-ll can,“ at can M or n c: u» A: by: one _: n: Optblnhtar Figure 18. Typical Digital Output Applications Outputs are not isolated from the repeater’s power subsystem. Provide a current source on the positive lead that does notexceed the following specifications: Forward Current—Continuous .............................. 300 mA -50 Volts Maximum Positive to Negative Lead Voltage- Maximum Negative to Positive Lead Voltage - 0 Volts Leakage Current in OFF State -- --- 1 "A See the “ACU Status Screen" in RepeateflVet Craft for the OAHSOC NH tor instructions about activating digital outputs See Table 17for lead descriptions. Alarm and Control Relay Outputs The OABSOC NR has both alarm and control relay outputs (Form C) with common, normally open, and normally closed connections. When attached to the normally open and common leads, an alarm relay closes a circuit when a critical alarm activates and opens the circuit when the condition clears. Relay Outputs #1 and #2 open and close circuits according to the relay output commie in FlepeaterNet. _ For example, to activate an external Ilght when the Relay Control switch is ON, the wiring loop includes the common connector, the normally open connector, 3 power source lor the light, and the light—see the following figure. OAESOC NR Operations Manual Chapter 4. Powering the OA5500 NR — 31 Preliminary Draft — RT! Confidential 5‘ in" (N0) 5 ID (N0) .=. Repeater IIO Custom Options To Rally (0) To Rel-y 01 or 52 To Rally an or n 01 or n (-) A: Relay 5: U9“ 0: a; su- Imwuctura acu Flgure 19. Typical Relay Applications Do not exceed the following specifications with relay connections: Maximum Switching Voltage and Current: 30 VDCIZ Amps, 200 VDC/200 mA See the “ACU Status Screen" in RepeaterNet Cralt for the OABSOC NH for instructions about activating digital outputs. Table 14 on page 30 shows I/O lead descriptions. Digital inputs The 0A1900 NFl has digital Inputs for external alarm monitoring and tar disabling the Forward and Reverse PAs. Each input triggers an alarm (or disables the PA) it the leads form a high Impedance circuit (an open contact) and clears an alarm if the leads lorm a low impedance circuit (a contact closing). NOTE: I! a PA rs drsabled usrng the digrtal Inputs, the PA Alarm rs tnggered. To avoid tnggerrng a PA Alarm in this manner, set the PA Alarm severity to disabled—sea 'Redelining Alarm Severity' in RepeatarNat craft for the 048506 NH. Connect digital inputs with two leads—the digital input lead and any ground lead. See the next two figures. OABSOC NR mentions Manual Chapter 4~ Powering the OAHEOC NR — 32 Preliminary Dlafl - HTl Confidaniiai +5V To Equlpmem 1m lKK Varlslor Repalur V0 0 Custom Options to mum mpmm one To Dlalul Inpnlln am To mghallnpfim urn A: any or swildi mu 5: Tran-"mar Input <2 "C ("it Input Flgum 20. Typical Digital Input Applications To Fwd/Rev PA Figure 21. Typical PA Dlubln Input Do not exceed the following specifications when connecting digital inputs: <0.5 Volts >4.0 Volts 5.0 Volts 00 Volts ..2 mA Input Voltage lor Logic 0 Input Voltage lor Logic 1 (active alarmldlsable PA). Maximum Input Voltage Minimum Input Voltage. Maximum Input Current OA8500 NH Operations Manual Chapter 4. Fowsn'ng lhs 0118500 NH — 33 Preliminary Dmfl - RTI ammoniml External Dc Input Voltage The OABSOC NR has one analog input to monitor an external DC power source. The monitoring range is from 0 to so volts, with a resolution of 250 mV. Connect an external DC power source to the repeater with a single lead lrom the positive line/terminal of the battery—see the following figure. - (i) To Equipment (+) Repeater Cabinet Ground Repeater IIO custom Options To Ext. + " Dc Mon. ’ A: Battery B: Battery (negativeg'omd) (puiliveg'and) Figure 22. Typr Dc Monitoring Applications CAUTION: Do not allow any input lo exceed the 60 Volts limit. _____________.__———-——— OMSOC NR Operations Manna! Chapter 4. Powering the OASEDC NH - 34 Preliminary Dralt — RTI Confidential Chapter 5. Orienting and Isolating Antennas Preliminary Antenna Orientation With the antennas mounted, coaxial cables installed, and the Repeater power OFF, antenna orientation can begin. BTS Antenna To orient the BTS antenna: 1. Disconnect the coaxial cable lrom the donor BTS antenna at the antenna port on the repeater. 2. Connect the service monitor to the cable from the BTS receiving antenna. 3. While monitoring the control channel assigned to the donor BTS, position the BTS antenna to maximize the RSL (Received Signal Level). 4. Analyze the signal to ensure it is correct. NOTE: Record the level at the control channel and other active carriers from the donor BTS for later reference. - It the RSL is less than Maximum RF Output Power Level minus Maximum Gain, full repeater output power may not be reached when installed. See Technical Specifications on page 9 lor RF output and maximum gain levels. To correct the problem, reposition the antenna, change the mounting height of the antenna, or use an antenna with greater gain to reach the required RSL. Mobile Antenna The Mobile service antenna can only be bore-sighted (aimed by eye) at this time. Aim the antenna as closely as possible to its linal position. Accuracy is important because the antenna position affects antenna isolation. Antenna Fundamentals An antenna is a transducer between electromagnetic waves in space and voltages or currents In a transmission line. When transmitting, the antenna converts electrical signals into radio waves; a receiving antenna reverses the process and transforms radio waves back into electrical signals. All antennas are directional, transmitting more power in some directions than others. The direction oi maximum transmission or reception ls called the bareslght direction. The directional propenies ol an antenna are described by its radiation pattern, a pictorial representation of relative radiated power versus direction. Radiation patterns exhibit a lobe structure in which the largest lobe in three- dimensional space constitutes the beam through which the antenna radiates or receives most of its power. The tendency of the antenna to concentrate its radiated power is called gain. The angular width of the main beam measured between the hall-power points is called the beamwidth oi the antenna. Beamwidth and gain vary inversely with each other, a high-gain antenna has a narrow beamwidth and vice versa. Gain is proportional to the physical area of an antenna expressed in square wavelengths. Radiation pattern lobes other than the main beam are called sidelobes. The higher the sidelobe level, the more likely an antenna is to interfere with or be interlered with by a receiver in the direction oi the largest sidelobe. 0118500 NH Operations Manual Chapter 5. Orienllng and Isolating Antennas —- 35 Preliminary Dralt — RTI Confidential An antenna has an operating frequency—the lraquency at which the antenna exhibits optimum performance—and a bandwidth—the frequency range over which the antenna impedance and radiation pattern remain within some required tolerance. Antenna Isolation To prevent oscillation or severe passband distortion, the antennas must have a port-to—port isolatlon equal to 15 dB plus the 0A850c NR active gain. For example, an OABSOC NF! set for a maximum available gain of 95 dB requires a minimum antenna isolation of 110 dB (95 dB + 15 dB) for proper operation. . Be aware that the motion of objects near the antennas can change the isolation significantly. If possible, perform tests with expected objects present to ensure the isolation does not drop below minimum required levels. To measure the isolation: 1. Disconnect both antenna signal cables from the antenna ports on the repeater. ' ' 2. Inject a signal into one of the antennas and measure the power level of that signal at the other antenna. The difference in power levels (measured in dB) between the injected signal and the measured signal is the isolation of the antennas. NOTE: Because antennas are not yet connected to the repeater, isolation is obtained through the air. 3. Repeat the test at several frequencies across the Forward and Reverse passband, confirming that minimum antenna isolation is met at all applicable lrequencies. 4. It isolation is not met, try repositioning the antennas or adding intervening shielding. and measure again. The following method can be used to estimate antenna isolation (referenced to dBd). During installation, always rely upon actual measurements, not estimated data. lsol=Ls+Ll+Lo-Gd+ADd-Gr+ADr+XPD US Standard Ls = —42.2 + 20logth x D), F in MHz, D in feet, Ls in dBd Metrlc Ls = -31.8 + zologm(F x D), F in MHZ, D in meters, Ls in dBd. Where The following are all in dB: lsol Antenna isolation Ls Antenna separation loss Lf Total Feedline Lose Lo Obstruction loss from structure or shield Gd Gain of antenna toward donor BTS ADd Angular discrimination of donor BTS antenna toward re-radiation antenna Gr Gain of re-radiation antenna toward Mobile ADr Angular discrimination of re-rediation antenna toward donor BTS antenna XPD Cross polarization discrimination between antennas (if applicable) OAB5OC NR Operations Manual Chapter 5. Orienling and Isolating Antennas — 36 Preliminary Draft — RT! Confidential Antenna Orientation and Output Measurement To orient antennas: 1. Turn OFF system power. The power switch is located in the upper Iett corner oi the Entry Box. Remove me 50-ohm terminators from the antenna ports. Connect the Donor and Mobile antenna ieeders to the proper antenna ports. Turn ON system power. WP?!“ Open a session with the repeater by selecting the repeater on the dialog box displayed after the Welcome screen. 6. Turn ON Forward PA and Reverse PA power: A) Select Fomard PA tram the Configuration menu. ., B) Click the Control tab. 0) Click the PA Power switch to turn it ON. D) Click Apply or 0K. Repeat tor Reverse PA. 7. Check Forward PA and ReverseyPA RF output power. A) Select Fomard PA from the Configuration menu. B) Click the Measurements tab. C) Compare displayed output power levels to the intended RF output power levels lor the system (defined in the site plan or network engineering documentation) and the maximum output power at the repeater. 8. Repeat for Reverse PA. NOTE: Fonflard transmit power increases as the orientation of the Donor antenna is optimized. Make any required adjustments to the Donor antenna lacing the Cell Site to maximize Forward power output. Adjusting for Hot Input Levels The CABSOC NFt has an adjustable gain range at 30 dB with upper and lower limits defined by the PA level of the repeater. In some applications, however, hot input levels require that antenna gain be set below the lower limit of this range. To set antenna gain below the lower limit at the operating range: 1. Choose a fixed attenuator pad that is able to set the gain to a level about 5 (15 lower than what is required. 2. Install the attenuator pad at the antenna port. 3. Make the final upward gain adjustment with FlepeeterNet. NOTE: If an attenuator pad is inserted in this manner, FiepeatarNet cannot show the actual antenna gain. For example, ii the Attenuator pad reduces gain by 5 dB, the system gain is actually 5 dB lower than the setting shown an the PA Properties screen. OABSOC NR Operations Manual Chapters. Orienting and Isolating Antennas — 37 Preliminary Draft — RT/ Confident/a! Chapter 6. Completing Installation « Turning On System Power RepeaterNet Craft is used for the first time during the installation procedure in this section. RepeaterNet Craft is the software program that confirms, controls, and monitors the OA850C NR. Make sure FtepeaterNet has been loaded on the laptop computer being used (at the installation site) to perform the initial conliguration of the repeater. If necessary- see RepealerNel Gran for the OABEOC NR To turn ON system power: 1. Terminate the CABSDC NR antenna ports with 7/13 DIN or Type N 50 OHM Power Loads. 2. Using a medium Phillips head screwdriver, remove the Entry Box access plate located at the front bottom of the unit and locate the internal backup battery. (See Internal Backup Battery on page 44 for inionnation on the operation ol this unit.) Problem Cause Solution Low RF Output Alarm Conditions =.-g Check tor alarm conditions and resolve, it or No RF Output » necessary. Strong, 0ut-ut~Band a Check antenna orientation. Inputs Improper galn setting =s Check gain and reset, If necessary. 3. Activate the power source to the repeater, then turn ON the repeaters power switch (located in the A upper left comer of the Entry Box). NOTE: The power switch is also a magnetic sensing circuit breaker. 4. Connect the red lead (quick disconnect type) of the internal backup battery. Conflmting Proper System Voltage You now must check the repeater, using FiepeaterNet, to confirm proper system voltage. To connect to the repeater and to conlirm proper system voltage: 1. Plug the lemale end of the 08-9 serial cable into the serial port ol the computer. 2. Plug the male end ol the cable into the serial port located in me Entry Box. 3. Start RepeaterNet. Start: — >Prograne - >Ropoltex~llet - >Rnpolt=erNet= 4 . If there is more than one repeater, select the appropriate from the list displayed to display the Main Control screen. 5. On the Login dialog box, enter a Login ID and Password. Click OK to open the FtepeaterNet Main Control screen. 7. Check the operation (color) of the Power subsystem (2-prong plug icon at the bottom of the screen): a Green—Normal Operation. Proceed to step 8. I: Red and flashing—Alarm Condition. OABSGC NR Operations Manual Chapter 6. Completing Installation — 38 Prelim/nary Draft 7 RT! Confidential Select Power System from the Configuration menu to open the Power System Properties screen. Identity the subsystem that triggered the alarm, and see Table 17 on page 43 tor information about resolving the alarm. NOTE: Clear any active alarms before proceeding with the installation. 8. If there are no alarms. or after clearing active alarms, continue with the procedure in the following section. Checking that Power Amplifiers are OFF All units are shipped with PAs turned OFF as indicated bythe PA OFF indicator (a circle with a slash through it) displaying over each PA subsystem icon (FPA or RPA) on the Main Control screen. PAs should remain OFF until you adjust the gain. if any PA subsystem Icon is not displaying the OFF indicator, do the following: 1. Select Forward PA or Reverse PA lrom the Configuration menu to open the Properties window. 2. Click the Control tab. 3. Click Ihe PA Power button to turn it OFF. 4. Click Apply or 0K. Determining the Correct Frequency Consult the site plan or network englneering documentation tor the proper channel or band settings for this application, In CDMA applications, primary and secondary assignments depend upon the Donor BTS with which the repeater Is coordinated. See the following table for a listing at CDMA channel assignments. Note that Korea and Japan use ditterent CDMA channel assignments. Table 15 Valid CDMA Channel No. to Frequency Cross Reference Chart Base to Mobile Forward (M Hz) 1 851.250 Ottlclal Channel No. 25 50 75 Quasi Channel Number Frequency Block 1 931 250 1 932.500 1 933.750 1 935.000 1 936.250 1 937.500 853.750 1 855.000 1 856.250 1857.500 1958.750 1988.70 1860.00!) 1940.000 225 1861250 1941250 250 1862500 1 942.500 1 1 275 1863750 1 943.750 Mk“, u/Qella/ln/r awn Nn-s 4- Freqjh OAHSOC NH Operations Manual Chapter 6. Completing installation — 39 Pie/minary Draft — RTI Confident/a! '_Frequency Quael channel Ofllclel Channel Base to Mobile Base to Mobile Block Number No. Forward (MHz) Forward (MHz) B 1 425 1871250 1951250 2 1 872.500 . 3 475 1 873.750 4 500 1875.00!) 5 525 1876250 6 550 ' 1957.500 7 575 1378.750 1958.750 8 600 1880.000 1960.000 9 825 1 961 250 1 0 650 1 962.500 1 1 S75 1963.750 C 1 925 . 1 976.250 2 .. 950 1897.500 1977.500 3 A 1895.750 1970.750 4 1900000 1980.000 5 ‘ 1901250 1901250 6 1902.500 1982.500 7 1903.750 1983.750 0 1905.000 1955.000 9 1906250 1956250 10 1907.500 1987500 11 1908.750 1988.75!) D 1866250 1946250 1867500 1947.500 375 1860750 1948.750 E 725 1886250 1966250 750 1587500 1967.50!) 775 1888.75!) 1966.750 _‘ 825 1891250 1971250 850 1592.500 1972.500 575 1593.750 1973.750 Setting the Channel or Band To set the operational channel or band: 1. Confirm that the repeater is ON and a direct connection has been established. 2. From the Craft Main Control screen menu bar, select channel 1 irorn the Configuration menu to open the Channel 1 Properties screen. On the Channel 1 Properties screen, click the Channel it tab. Type the channel number in the Channel field to define a channel. Click Apply or OK to set the channel. Configuring Gain Initlally When initially setting Forward and Reverse Gain, use the gain settings defined on the project site plan or in network engineering documentation. (If necessary, contact your network administrator.) Final adjustments to gain settings are made during system optimization. 0AB5OD NH Operations Manual Chapter 6. Completing [installation — 40 Plellmlnflry Dmft— FlTI Confidential ' To initially set gain: 1. 2. 5. Confirm that the repeater is ON and a direct connection has been established From the Craft Main Control screen, select Channel 1 from the Configuration menu to open the Channel 1 Properties screen. Click the Gain tab. Click-drag each horizontal slider to define Forward and Reverse gain, noting that gain adjusts in 2 dB increments. The gain value box (centered under each slider) displays selected gain. Click Apply or 0K to set the gain and return to the Main'Control Screen. ________—___._———-—-—— NOTE: For 2-channel units, select Channel 2 and repeat steps 3 and 4 for the Channel 2 Forward and . Reverse PAs. Verifying and Optimizing the Coverage Area For detailed inlon'natlon about repeater installation and link engineering, request the engineering handbook, Installation, Operation, and Optimization of Over-theAir Cellular and PCS Repeaters. directly from Repeater Technologies. M8506 NH Operations Manual Chapter 6. Completing Installation — 41 Preliminary Draft — RY! Confidenh‘al Chapter 7. Maintenance and Troubleshooting -\ The OABsOC NR is a field-replaceable unit that requires no component-level repair. The use of highly reliable components virtually eliminates maintenance. Routine checks of the OASSOC NR and its supporting equipment are recommended to ensure reliable operation and early detection of problems. Routine Maintenance Repeater Technologies recommends a semi—annual maintenance schedule for the repeater. A procedure for routine maintenance lollows: 1. Inspect the installation site and correct any problems. 2, Verify that the OABSOC NR and all associated hardware, including antennas, is securely mounted and properly in place. 3. Check input electrical wiring and BUPS for damage and ensure that connections'are tight 4. Check any battery terminals for corrosion; clean terminals, it necessary. 5. Clean solar panels and remove obstructions, if applicable. CAUTION: Follow manufacturers instructions when cleaning salarpanels. Abrasive or acetone-based solutions can cause damage to some types of panels. 6. Check antennas and coaxial cabling for damage and ensure that connections are tight. 7. Check the tins of the heatsink and clear any debris. LEDs The OABSOC NR Entry Box displays lour LED indicators-see the following table. Table 16. Descriptions of LED indicators LED indicator Description LED Color Normal Systemneaav Poweron —-a--ar- amicawam crmcawarmmgereu Major Alarm Major Alarm triggered Red Off On steady Minor Alarm Minor Alarm triggered Yellow Off On steady Troubleshooting Perlorm all troubleshooting oi the OAGSOC NR with RepeaterNet. See the following table tor a listing at common problems and possible solutions. _._—._—__——~_——-—— NOTE: Contact the Repair Department of Repeater Technologies wheneverpmblems with the unit can not be resolved—see ”Repair and Return Procedure.” «7 _—____—___.__.———— OA8500 NR Operations Manual Chapter Z Melntenance and Troubleshooting - 42 Prallmlnary Draft — HTI Confidential Table 17. system Troubleshooting Solution => Run the Scan Disk and Deiragmenter utilities included with Windows 95. =. Reinstall RepsaterNel. Unable to start RepeatarNet Corrupted Program Data Improper Installation at RepeaterNet Damaged Hard Drive => Repair or replace hard drive. = Check telephone number, COM port. stop blts, parlty settings. and baud rate. Correct settings, it necessary. => Check advanced settings from the COM Properties screen. Reduce butter sizes or disable butter and retry connection. => Check Hie cable for a tight connection. . = Check the cable and connection pens for damage. Replace cable, it necessary. Contact Repeater Technologles it the connection port is damaged. => Check telephone line connections at the computer and the Repeater. Flo-connect, it loose. 9 Check telephone line tor damage. Replace, it necessary. : Log in to a direct session with the Repeater and check the modem and cell phone alarms. It either alarm is active and does not clear. contact Repeater Technologies. z: Check the compuler's modem. Replace or repalr computer modem. II necessa . Overheating Insulticient Cooling : Check the heatsink. Clear any airflow obstructlons. => he at e um: I| sin ane remey o envtronment. (TWP-NW) Sdh l'i'l' xt Iht ' Low Voltage or Improper Solar Charging :7 Clean solar panels or remove obstmctions. Do not use No Voltage an acetone-based solutlon tor cleaning. (“PM POWS’ = Check the condltlon oi the power source. Alarm) => Check all wiring and power leads to the power source. : Check any tuses or circuit breakers In power supply equipment. => Check AC power service tor outages or other service problems. :> Contact Repeater Technologies to replace unit. => Adjustgain. = Contact RepeaterTechnologies. => Check to ensure Repeater power is ON and both PAs are turned ON. z: Check antenna orientatlon and re~align, it necessary. Improper COM Settings Serial Cable Failure Modem Fallure Power Supply Fal|ure Internal Power Converter Fallure ALC Power L Gain Incorrectly Set Alarm PA Failure Low RF Output or Controls Not Tumed ON Nu HF Outpul Mobile or Bass Antennas Oriented Incorrectly 0148500 NR Operations Manual Chapter 7. Malntenanoe and Troubleshooting — 43 Preliminary Drsfl— RTI Confidenn‘al Low HF Output or Alarm Conditions :> Check tor alarm conditions and resolve. it necessary. No FtF Output Strong, Out-ot-Band = Inputs Improper gain selling Check gain and reset, if necessary. Active Alarm =7 Resolve alarm. Foreground reflections : Remove obiect causing reflection; adjust antenna orientation; move antenna mounting. Improper Antenna =:~ Clear area around antennas of excessive plant growth. Isolation Improper Gain Settings Check antenna orientation. Oscllletlon Internal Backup Battery" The OABSOC NF! includes an internal backup battery to provide limited back-up power for the ACU and, if applicable. the cell phone and lntemal modem. In the event at a loss of system power, the internal battery provides power tor the repeater to call out and report the lailure, and to save the Alarm and Event Log. The length of time that the internal battery provides power depends upon Repeater configuration and environmental conditions (such as temperature). Table 20. lntemal Battery Backup Opel-Ila" Estimates Configuration Operating Tlme‘ Repeater with no lntemal modem Repeater with lntemal modem and no cell phone Repeater with Internal modern and cell phone. with modern and phone continuously transmitting ‘Values are esllmates only: actual battery life may vary. Estimates assume a fully charged battery, adverse environmental conditions, and a 600 mW AMPS cell phone. System power charges the internal battery during normal operation. Note that the internal battery has a low voltage cut—off to allow for a full recharge when power is restored. If a power outage lasts longer than the operational Iimlt of the internal battery, the modern cannot send or receive calls. and Alarm and Event Log data is lost. Save the Alarm and Event Log when the repeater calls out to report a system power failure—see “The System Menu” in Repeaterst Craft for the OASSOC NR for more information about the Alarm and Event Log. NOTES: u The internal battery does not provide power for RF transmission during a primary power outage. Servioe is interrupted during a loss of primary system power. a The battery should be replaced on a 3-year cycle to allow for normal aging, wear, and environmental deterioration. OABSOC NH Operations Manual Chapter 7. Maintenance and Troubleshooting — 44 Preliminary Drafl — HT? Confidential Sparing Recommendation Because repeaters are often used to provide critical coverage, customers are advised to follow a sparing policy. While most carriers have intemel policies related to equipment sparing, in the event that one does not exist, Repeater Technologies recommends that a carrier maintain a minimum of one (1) spare unit for every increment of 10 units or lraction thereof. This assumes that all spares are immediately available to the technician for installation. It is advised that each carrier develop a company-specific, equipment-specific policy. one that accounts for geographic and environmental (actors and the total number of repeaters deployed in a given network. Repair and Return Procedure if a repair or return of the OASSOC Is necessary, Contact the Repeater Technologies Customer Service Department for Instructions. Note that Customer Service needs the lollowing information from you when you call: ct A detailed explanation of the problem it The model name " a The serial number of the unit For equipment returns, a Repeater Technologies representative issues an RMA (Return Material Authorization) and shipping and packaging instructions. When reluming the OABSOC NR, always use the original shipping carton and packaging materials. It the original shipping materials are unavailable, Repeater Technologies can send replacement materials at the cost of the purchaser. CAUTION: if equipment is not returned to Repeater Technologies in the original packaging materials, possrble damage could result. Repeater Technologies is not liable for any damage resulting from improper shipment. Customer Service phones are staffed or monitored 24 hours a day, 7 days a week. Phone numbers for the Customer Service Department are as lollows: (408) 747-1946 (800) 933-1901 (USA and Canada only) Product Warranty. A one-year product warranty is provided with the 0A1900 NR. A copy 0! the product warranty is included with the Standard Terms and Conditions in every sales agreement. For more information, contact the Repeater Technologies Customer Service Department. OAB5OC NFl Operations Manual chapter 7. Maintenance and Troubleshooting — 45 Pmllrninaly Dial! — HT! Confidential Glossary This glossary defines communications industry acronyms, related acronyms have also been included. As this glossa Repeater Technologies, not all items listed here necessarily appear in this manual. AcU ALC AMPS BNC HTS BUPS CDMA CPO ORG DAMPS dB dBc dBl dBm on, on own an am am: Fla FCC FE FIFO Amp or Amps. Alarm Control Unit. Automatic Level Control. Advanced Mobile Phone System. ‘Type of connector. Base Transceiver Station. Back-up Power Supply. Code Division Multiple Access. Canter-to-Echo Ratio. ~ carrier-telnterface Ratio. The ratio between the mean signal level of the desired radio signal and the signals from other. interfering sources. typically expressed in dB. Circular Plastic Connector. Cyclical Redundancy Check. Digital Advanced Mobile Phone System (equivalent of TDMA). Decibel or decibels. Decibels referenced to the carrier level. Decibels referenced to the isotropic antenna. Decibels referenced to one milliwatt. Distributed Feedback (Laser). Digital Voltmeter. Electromagnetic. Electromagnetic Interlerence. Effective Radiated Power. Front-to-Back Flatio. Federal Communications Commission (USA). Front End. First In First Out. symbols, and terms. Hardware- and software— ry supplements all operations manuals of FORWARD DlREC‘flON FORWARD GAIN FRU FSK GSM GUI HAND-OFF HOT TONE IF IM IMD LED LNA LO microCelI usc MTSO Direction oi transmission from the base station through the Repeater and on to Mobile or hand-held units. Downlink transmission. Gain setting lor Forward transmissions. Field Replaceable'Unit Frequency-Shift Keying. Global System for Mobile Communications or Groups Spociale Mobile. Graphical User interface. The act of transferring the service of a call in progress on a cellular system from one cell or sector to another, typically also involving a change in the voice channel used. If a Mobile transmits at full power in close proximity to a receive antenna, a hot tone—tor example. a receive signal above -40 dam—is produced. Too hot a tone can over-modulate a system and force It to drop all calls. Systems designed to control reverse attenuation will moderate the potentially damaging effect of hot tones. Intermediate Frequency. Intermodulation. Intennodulation Distortion. Light-emitting diode. Low Noise Amplifier. Local Oscillator, high-level input into mixer. Any small, low-power cell site. Mobile Switching Center (equivalent to MTSO). Mobile Telephone Witching Ollice (equivalent to MSC). 0148500 NR Operations Manual Glossary — 4s Preliminary Drah— nrr Confidential MULnPArH Radio propagation between a NR OTU PA PCS PSTN PEP PLL QCCB RBS REVERSE BIREC'HON transmitter and receiver where the received signal is a compound at multiple rays that have undergone one or more rellections and/or refractions. Cellular coverage is most often provided in a multipath environment. especially in high- density city areas. Network Repeater. Optical Transceiver Unit. » Power Amplifier. Personal Communications Service. Public Switched Telephone Netwont. Peak Envelope Power. " Phase Locked Loop. Quick Connect Connecting Block. Radio Base Station See also BTS. Direction of transmission lrorn the Mobile or portable through the repeater and onto the RBS. Uplink transmission. Craft for the OABSOC NR REVERSE GAlN RF RFI RSL RSA RSSI ‘ RX SIMULOAST SMA SMB TDMA TSA UHF UPS VAC VDC VSWR XPD Gain setting for Reverse transmissions. Radio Frequency. Radio Frequency Interference Receive Signal Level. Rural Service Area. Receive Signal-Strength Indicator. Receive. The process of transmitting the same signal from two or more sites simultaneously. A type of connector. A type ol connector. Time Division Multiple Access (equivalent to DAMPS). Tralfio Servlce Area. Transmit. Ultra High Frequency. Uninterruptable Power Supply. Volt or Volts. Voltage, Alternating Current. Voltage, Direct Current. Voltage to Standing Wave Ratio. Wart or Watts. Cross Polarization. Glossary — 47 Preliminary Drfifl — HTI Confidenlial fiffibffiflfl CM for the 043500 NR Glossaly- 48 Pref/"Wham Drah — RTI Confidsnfial RepeaterNet Craft for the OA85OC NR DRAFT 61 u mmmm 1150 Morse Avenue - Sunnyvale, CA 94089-1605 ' USA ' Tel: +1408 747-1900 ' 550-4999-02 Revision A Repeatemer Software Version 2.2 Sepl'lmbflf 1993 Fax: +1 408 747-0375 Preliminary Draft — HT! Confidential Contents Chapter 1. Installing RepeaterNet . RepeaterNet Crett Software Minimum System Requirements. Installation Procedure........... Chapter 2. Repeateer Craft... Configuring the Repeater Connection Staning Craft OABSOC NR ra Configuration. Status Reporting. Alarm Status Reporting on the Main Control Screen. Defining Alarm Severity.. . Chapter 3. Contigurlng OABSOC NR Prope 53 Front End Properties. Forward FE Tab Heve rse FE Ta Diversity FE Tab. Diversity FE Gain Tab Channel Properties Channel Revers Channel Forward PA Tab Channel PA Control Tab .. Channel Reverse Filter Tab. Channel Forward Filter Tab. Channel # Tab Channel Gain Ta ACU Properties ..... Inputs and Outputs ACU I/0 Descriptions Tab ACU IIO Controls Tab ACU Alarms Setting T ACU DC Voltage Alarm Thresho Modern Properties. at”. ain't”. Modern Setting Over-the-A Pager Setting. Cell Phone Propertie Power System Properties Backup Power System (UPS) Properties Chapter 4. Monltoring 0Aasoc NH Status Front End Status .. Channel Filter Statu Channel PA Status PA Alarm Tab PA Measurement Ta ACU Status ACU Alarm. 4 Measurement. 4 Modern Status .. Craft for the OASSOC NR Contents — Page 3 Prel/mlnary Draft — RT! Confidential Cell Phone Status... Power System Status Alarm . Voltages. UPS Status... Chapter 5. RepeaterNet Commands File Menu—OASSOC Craft Download Properties Upload Properties Update Repeater Exi System Menu—OAESOC NR Craft Properties ...... 29 System Tab . 29 System Inventory Tab . . 30 Log in Tab 30 Alarm and Event Log Saving , Priming, and Editing the Log Options Menu—CABSOC NR Cra Color Independent Icons. Alarm Sounds 32 Hold Connection 32 Help Menu—CABSOC NR Craft. 32 Navigating Help. Exiting FiepeeterNe Appendix A. Default Alarm Settlngs Appendix B. RepeaterNet Executable: .................................................. Appendix C. The Oki Cellular Phone Accessing the OKI Cellular Phone Programming the OKI Cellular Phon Appendix D. Troubleshooting ...................... —fi————— Craft for the OABSOC NR Contents - Page 4 Prallmlllaly Drafi— FlTl Confidential Chapter 1. Installing RepeaterNet This chapter briefly describes the components of the RepeaterNet software, identifies minimum system requirements, and describes the installation procedure. RepeaterNet Craft Software The RepeaterNet Craft software (craft) provides Windows 95- and Windows NT-based configuration management and alarm monitoring for individual Repeater Technologies repeaters and dynamically manages sessions in real time through one ot these connections: I: A laptop computer with a direct connection to the repeaters—a technician can visit repeater sites and connect to the repeaters directly using the serial port on the laptop. n A laptop or desktop computer with a modem connection to the repeater—with the modem connection. e technician need not visit the physical repeater sites to connect to the repeaters. The Craft user interface varies, depending upon the model repeater being configured or monitored. Minimum System Requirements Craft system requirements include: ct Pentium 120 MHz running Windows 95 with 32 MB of memory CI Approximately 10 MB of free disk space El Modem (it a modem connection is to be used) NOTES: Ci The Craft system must be used with Windows 95 with Service Pack 1 Update (Version 4.00950 A) or later releases or Windows NT, Service Pack 3 Update ct Use "Hayes—compatible" modems only. “Connect with Rockwell” certified for modems of 56K and above. US Robotics modems are not supported. Er If you use a fax program such as Microsoft Fax, make sure that the Auto Answer feature ls disabled. See Appendix D. Troubleshootlng on page 38, Problem 7, for how to disable Auto Answer for Microsoft Fax. Installation Procedure The OABSOC NR Craft software is distributed on 4 HD floppy disks. To install: 1. Insert Disk 1 in your a: drive. 2. From the Windows Start menu, select Run. 3. Type a:\setup and click on OK. 4. Follow the online instructions to install the Craft software. The Craft software comes with default configuration files, which you can download to your repeater according to the repeater type and number of channels. This eliminates the need to configure the properties manually. See Download Properties on page 27. Craft for the OABSOC NR Chapter 1. Installing RepeaterNet— Page 5 Preliminary Draft — HTI Confidential Chapter 2. RepeaterNet Craft A Configuring the Repeater Connection You must use the RepeaterNet Craft Admin program to configure the connection to the repeater before you can access the HepeaterNet Craft software. Follow this path from the start menu to invoke the HepeeterNet Administrator: Start -> Programs -> RepeaterNet Craft 2.2 -> RepeaterNet Craft Admin When you invoke the Administrator, a window such as the following is displayed: You can save both Direct and Dial-Out (Modem) »‘ --—~e-——__- mli rum Em. Mm. configurations, but remember to assign a unique COM Port Number to each. Also, be sure to check Use this connection for only one of the configurations. The connection checked is the connection RepeaterNet Craft uses to connect to the repeater. For example, you may assign the connection type as Direct mammal through COM Port 1. You can check the Use this connectlon box to make this your default configuration. m“ mum». It] Click on Save. Next, you can save a Modern configuration to another COM port, such as COM Port 2: 1. Assign a COM Port Number that is different from the COM Port Number used for Direct connection. _L Unlillmi 2. Click on Save, then click on OK to exit RepeaterNet Admin. Starting Craft Double-click the Craft icon to display this window. HepeaterNet connects to the repeater and displays the Crait Main Control screen for the 0A85OC NFL OAssoc NR Craft Main Control Screen The Crait Main Control screen provides access to all monitor and control functions of the 0A8500 Network Repeater (NR). Craft for the 0A 8506 NR Chapter 2. RepeaterNst Craft — Page 6 Preliminary Draft — HTI Confidential Main Control screen icons (labeled on the following screen) provide access to subsystem stalus screens and report alarms. Forward Chlnnel 1 Front End Forward Power channel 1 Amnllfinr Forward Chlnnel Select Fllle' Channel 2 ~ F cm...” pill?!" Fem-rd Amnmlev channel Select Flu-r channel 1 Revel" Chlnnel Channel 1 Select Flller Reverse Power R. F d Ampllller Vern mnl En Dlverslty From End Channel 2 Reverse Power Channel 2 "mm" Revetsa channel Select Fllttl' Alarm Control Modern Cell Phone Power Back-up Power unn Supply OA850C NH Craft Main Control Screen NOTES: 0 All units are shipped with FA; tamed OFF as indicated by the PA OFF indicator (a circle with a slash through it) displaying over each PA subsystem ioon (FPA and EPA). PAs should remain OFF until gain is adjusted. a The Main Control screen displays differently depending on the hardware configuration of the unit. For example, Channel 2 icons are grayed-out (unavailable) fora single—channel repeater. Craft for the OABSOC NH Chapter 2. HepeaterNet Craft — Page 7 Preliminary Draft - HT! Confidential Configuration Configure the OABSOC NR on subsystem Properties screens, which you can display from the Craft Configuration menu. The Configuration menu contains the following: Front End Channel 1 .Forwerd, Reverse, and Diversity . Available on all units Channel 2 .Avei|able on 2-channel units only Alarm Control Un , ACU ' Modem ....... .lntemai or external modem option Cellular phone Cellular option only . Power System input, battery, and intemai UPS ...... Backup power system Status Reporting Once you have configured the repeater, you can monitor and control repeater system functions on subsystem Status screens Click a subsystem icon to open its status screen. When an alarm is triggered. the subsystem icon changes appearance, blinks, and activates an audible alarm. Clicking on the icon and viewing the subsystem status screen stops the blinking and the audible alarm. The display of the icon does not revert to normal until the alarm condition is cleared. The display of the Forward PA and Reverse PA icons also indicate the operational status oi the PAS. ii a PA is OFF, a circle with a slash is displayed over the associated icon. When RepeaterNet displays a subsystem as disabled, that subsystem is not available to the repeater. For example, in repeaters without a cellular phone, the cellular icon is displayed in light gray. Alarm Status Reporting on fhe Main Control Screen FiepeaterNet uses a color system to report subsystem alarm status on the Main Control screen. The meanings of the colors. and color independent icons, is shown in the following table. subsystem Alarm Status icon Color Color independing Icon Action Normal—No Alarm Green N/A NIA Tl Critical Alarm Fled x Cali om Major Alarm Yellow \ Call Out Minor Alarm Blue ""~~._ Call Out Event White None None Disabled Dark Gray' N/A None 1 System Not Available Light Grey N/A‘ N/A ' When all alams in an individual subsystem are disabled or set to event severity, the Icon color Is displayed in dark gray. Craft for the OAB5DC NR Chapter 2. Repeats/Net Craft ~ Page 8 .‘ Preliminary Drslt — FIT! Confidential When an alarm is triggered, the icon color at the affected subsystem changes from green (normal) to the color of the alarm definition, and the icon blinks. RepeaterNet also otters two optional alarm leatures: a Color Independent Icons is provided for operators unable to distinguish colors u Alarm Sounds adds an audible alarm Should more than one alarm within an individual subsystem be triggered, the higher severity alarm is reported on the Main Control screen. . For example, if both a major and a minor Reverse PA alarm triggers, a yellow subsystem icon is reported. It the major alarm is cleared while the minor alarm remains active. a blue subsystem icon is reported. Color-independent icons also report the hlgher severity alarm, should more than one alarm on an individual subsystem be triggered. NOTE: When an subsystem alarm is triggered, click the icon (to open the status screen) to terminate the icon blinking feature and silence the audible alarm. Icon color continues to report and a color independent icon (if applicable) continues to display until the alarm is cleared. Color reporting does not apply to subsystems set to Event severity. Defining Alarm Severity The OABSOC MP! is lactory-configured with a standard set of alarm severity settings. Adjust alarm severity on the subsystem Properties screens. See chapter 3. Configuring OABSOC NR Properties on page 10 tor more information about alarm severity and the factory conliguration. The levels of alarm severity are: D Critical El Major 0 Minor in Event D Disabled To define alarm severity: 1. Login to a sesslon with the repeater. 2. Select Configuration tram the Main Control menu bar, then select a subsystem to open its Propertles screen. For example, select Configuration -> Channel 1. The Alarms tab is displayed. 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or 0K. Craft for the OA6500 NH Chapter 2. FlepeaterNet Craft — Page 9 Pre/irrl'nary Draft 7 FIT! Confidential Chapter 3. Configuring OASSOC NR Properties " Use the subsystem Properties screens to periorrn configuration of the repeater. To open 3 Properties screen, select a subsystem from the Configuration menu. Front End Channel 1 Channel 2 Alarm Control Unit Modem Cellular Phone Power System U PS The Properties screens display tabs specific to each subsystem. Some subsystem Propenies screens include tabs for redefining alarm severity and specifying operational settings; others have a single tab for redefining alarm severity. EEDDEIUEID Configuration includes: Fem-“E lam-rs] Dmmloheayrssm] 0 Redelining alarm severity \:| Specifying operational settings for the repeater Front End Properties The Front End Properties screen lets you configure the Front End subsystems This screen includes tabs that let you set the alarm severity for: El Forward FE D Reverse FE D Diversity FE Forward FE Tab The Forward FE tab lets you set the alarm severity of the Forward FE alarm The Forward FE alarm is activated when the lorward signal power level is too strong and is belng attenuated to protect the repeater from possible damage. if NOTE: Do not adjust power amplifier gain while this alarm is active. Reverse FE Tab The Reverse FE tab lets you set the alarm severity at the Reverse FE alarm. The Reverse FE alarm is activated Mien the reverse signal power level is too strong and is being attenuated to protect the repeater lrom possible damage. Craft for the OABSDC NR Chapter 3. Configuring 0148506 NFi Properties — Page 10 Preliminary Draft — RTI Confidential NOTE: Do not adjust power amplifier gain while this alarm is active. Diversity FE Tab The Diversity FE tab lets you set the alarm severity ol the Diversity FE Alarm and set the gain of the Diversity receiver. The Diversity FE alarm is activated when the Diversity Receive signal power level is too strong and is being attenuated to protect the repeater from possible damage. __—_____’ NOTE: Do not adjust power amplifier gain while this alarm is active. Diversity FE Gain Tab Gain must be carefully balanced in any application to ensure proper hand—off and system operation. repeater and displays the applicable gain range on the FE gain: The adjustable gain range depends upon the type of repeater you are using and the power level of the power amplifiers. To adiust Diversity FE gain: 1. Select Configuration ->Front End to open the Front End Properties screen. 2. Click the Diversity FE Gain tab. 3. Click-drag the horizontal sliders to define lorward and reverse gain, noting that gain adjusts in 2 dB increments. The gain value box (centered under slider) displays selected gain: 4. Click Apply or OK. Channel Properties rum-d rs] RwaneFE Div-isms lDrvusily r: Gaul fl From the Main Control screen menu bar, select channel 1 or Channel 2 (for 2-channel units only) to open a Channel Properties screen. Channel properties include: Reverse PA Forward PA PA Conth Reverse Filter Forward Filter Channel # Gain DCIUCIDDO Craft for the 0A850€ NH Chapter 3. Configuring OABSDC NR Properties -— Page 11 Preliminary Draft — RTI Confidential Channel Reverse PA Tab ‘\ The Reverse PA tab shows the most recent alarm slate, including severity. date, and time. for these alarms: PA Alarm Ehmndl I’mrutln- Indicates a component lailure in the power amplifier; the repeater is inoperafive. VSWR Alarm Indicates a problem with the Voltage to Standing Wave Ratio. Rm! Eu smug-n Thermal Alarm Indicates the system temperature has exceeded the alarm threshold. The repeater has been shut down. When the temperature tails below subsystem tolerances. the repeater automatically reactivates the PA. External Shutdown Alarm Indicates that the repeater has been shut down by a user; also activates one RPA alarm. Redeline alarm severity tor the Reverse PA subsystem on this tab. 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2, Click Apply or 0K. See Forward PA for a sample screen. l'Innnf-I PM E! r‘ Channel Forward PA Tab The Forward PA tab shows the most recent alarm state, including severity, dale, and time, tor these alarms: PA Alarm Indicates a component failure in the power amplifier; the repeater is inoperative. VSWR Alarm Indicates a problem with the Voltage to Standing Wave Ratio. Thermal Alarm Indicates the system temperature has exceeded the alarm threshold, The repeater has been shut down. When the temperature falls below subsystem tolerances, the repeater automatically reactivates the PA. PM! 515me External Shutdown Alarm Indicates that the repeater has been shut down by a user; also activates one RPA alarm. Craft far the OA8500 NR Chapter at Configuring OA8500 NH Properties —- Page 12 Preliminary Dre/t — HT I Confidential Redefine alarm severity for the Forward PA U. man | mm.» subsystem on mis tab. 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or 0K Channel PA Control Tab The PA Control tab provides a switch to tum PA power ON or OFF. 1. Click on ON or OFF in the PA Power box to change the value. 2. Click Apply or OK for the setting to take effect. Channel Reverse Filter Tab This tab displays the most recent alarm state for a single channel select filter alarm. A failure in the Reverse Filter assembly triggers an alarm and the filter becomes inoperative. Redefine alarm severity for the Reverse Filter subsystem on this tab. 5 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or OK Values are Disabled, Event, Minor, Major, and Critical. See Forward FIIIer for a screen example. Chimnillh; Channel Forward Filter Tab lmgl This tab displays the most recent alarm state for a single channel select filter alarm. A failure in the Forward Filter assembly triggers an alarm and the filter becomes inoperative. csrt rmdAlam Redefine alarm severity tor the Fonrrard Filter subsystem on this tab. 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or 0K. Values are Disabled, Event, Minor, Meier, and Criticalt Craft for the OABEOC NR Chapter 3. Configuring OABsoC NR Properties — Page 13 Prsllmlftaly Draft — RYI Comic/antral Channel # Tab The Channel # tab lets you set the operating channel or band for Channel 1 or Channel 2. Once you select a channel, the corresponding frequencies are an displayed. Consult your network administrator or the “ system Site Plan for the proper channel or band fwrmww” [15755 setting. Rev-"Frmwlld [TEE Mai-val Channel Gain Tab ' HepeaterNet detects the configuration of the repeater and displays the applicable gain range on the Gain tab. You can adjust Forward and Reverse gain lor the selected channel. The adjustable gain range depends upon the type ol repeater you are using and the power level of the power amplifiers. RepeaterNet limits gain adjustment to valid selections only. NOTE: Set gain for the Diversity Receiver an the Diversity FE tab of the Front End Properties 50185". M“ Gain must be carefully balanced in any application to ensure proper hand-oil and system operation. To adjust Fonrvard PA or Fleverse PA gain: 1. Select Configuration ->channel 1 or channel 2 to open the Channel Properties screen. 2. Click the Gain tab. 3. Click-drag the horizontal sliders to define forward and reverse gain, noting that gain adjusts in 2 dB increments. The gain value box (centered under each slider) displays selected gain. 4. Click Apply or 0K. ACU Properties Select Alarm Control Unit from the Main Control screen Configuration menu to open the ACU Properties screen, This screen includes tables for V0 Descriptions, "0 Control, Alarms, and 00 Voltage Alarm Threshold The ACU subsystem provides alarm and control functions for the repeater. The ACU monitors all the repeater subsystems and reports status to a connection device or to remote devices through a dial-up modem connection. in addition to monitoring the repeater system, the ACU contains a number of external inputs and outputs to monitor and control external devices. Inputs and Outputs RepeaterNet lets you monitor two digital alarm inputs and one DC voltage InpUt lrorn external devices. You also can activate up to four external devices with two relay outputs and two digital outputs. Craft for the OABSOC NH Chapter 3. Configuring OA8500 NFI Properties — Page 14 Preliminary DIE/l — HTI Confidential NOTE: Alarm settings [or digital input 1 and digital input 2 are initially set to Disabled. The inputs and outputs are as loIIows: Relay Outputs 1 and 2 The two relay outputs are configured with three leads In a Form C Contact Closure, with normally closed and common connectors closed with the switch in the OFF position and normally open and common connectors closed with the switch in the ON position. Digital Output: 1 and 2 . The two digital outputs each have two leads that provide an opts-isolated circuit that presents a low impedance connection when the switch is in the ON position and a high impedance connection when the switch is in the OFF position. Digital Inputs 1 and 2 The two digital inputs each have loads that generate an alarm condition it the leads form a low impedance circuit (a closed contact), and a clear condition it the leads form a high impedance circuit (an open circuit). For information about connecting inputs and ;,~|.m....mm| u." "w "w outputs to the repeater. see the OABSOC NH Operations Manual ACU l/O Descriptions Tab Label external equipment connected to the repeater's inputs and outputs using the V0 Descriptions tab. Extemal equipment could be a security light or any other site equipment. To add llO Descriptions: 1. Select Contiguration->Alarm Control Unit to open the ACU Properties screen. The I/O Descriptions tab is active. 2. Provide I/O Descriptions in available data fields. 3. Click Apply or OK. ACU l/O Controls Tab The I/O Controls tab contains switches to turn Relay Outputs and Digital Outputs for channels 1 and 2 ON or OFF. See Inputs and Outputs. Graft for the 0A85OC NFl Chapter 3. Configuring OAasoc NH Properties — Page 15 Preliminary Draft - HTI mnlldsnlial ACU Alarms Setting Tab "W" ‘ """"' ”m m” "" N— Ftedefine alarm severity for ACU subsystems on the Alarms Settings tab. 5. 5! “URN-m 1. Click the down-arrow next to an Alarm liald to lam select a new alarm severity. mm,” 2. Click Apply or OK. Values are Disabled, Event, Minor, Major. and Critical. ACU DC Voltage Alarm Threshold Tab HepeaterNet can monitor an extemal DC voltage power source (a battery) in a range of 0 to 80 volts in 250 mV increments. in addition to monitoring the voltage level, you can define upper and lower limits lor the voltage that Is to activate the DC Voltage alarm in the ACU subsystem. Monitor the voltage at a DC power source (supplied by you) used to power external site equipment using the DC Voltage Alarm Threshold tab. An alarm is triggered it the voltage fluctuates from a defined operating range. my”. I‘m-lull um n“... f _._ nmummmvmmmnsuwoc To define an operating range for DC voltage: .’ E” g r.“ : 1. Select Oontiguretion->Alarm Control Unit to l Em [0—3 open the ACU Properties screen. 2. Click the DC Voltage Alarm Threshold tab. 3. Define (type in or arrow-click) the normal operating range lor the DC power source in the Less Then and Greater Than data fields. 4. Click Apply or OK. Modem Properties From the Main Control screen menu bar, select Configuration->Modem to open the Modem Properties screen. This screen has three tabs: Alarm Sottlng Lets you set the alarm severity lor the Modem alarm. This alarm indicates a failure of the internal modern. Modem Setting Lets you define the port settings for the Internal or extemal modem, Pager Setting Lets you configure a pager to be notified when a certain severity level alarm occurs. Craft for the OABsoC NFl Chapter 3. Configuring OASSOC NFl Properties — Page 15 Preliminary Draft — RTI Confidential Alarm Setting Use the Alarm Settlng tab to redefine alarm severity for the repeaters modern. 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or OK. Values are Disabled, Event, Minor, Major, and Critical. Modem Setting Define modern settings for the repeater‘s modem using the Modem Propertles tab. To define modern settings: 1. Select Modem from the Main Control screen configuration menu to open the Modern Properties screen. 2. Click the Modem Settings tab. Model“ Properties 3. Define the Setup String, Phone Number, and “ms“ “mm lvwsm| Cell Attempts. 5m“? If Phen- Nllrbfl 0 4. Click Apply or 0K. “mm [0—— Setup Strlng is reserved tor configuring a cell phone PM“ or modem. The cellular phone setup string is $37=6. Phone Number is the phone number of a remote computer to be called. This value is 0 unless you are using RepeaterNet Network Management software or other network management soltware. Call Attempts is the number of callout attempts beiore disconnecting; a zero (0) disables calling. Baud Rate is the communication speed between the modern and cell phone (which must be greater than 2400). Baud Ftate is adjusted automatically downwards by the modem when necessary. Set Parlty to None. Parity must be set the same as the computers modem. Set Date Bite to B. Data Bits must be set the same as the computers modem. Set Dial Type to Tone. Over-the-Air Repeater Modem Setup If an external wireless interface (such as the Telular) is connected to an 0A (Over-the-Air) repeater, you must properly configure the repeaters modem. if the modem is not properly set up, few if any oi the calls to the repeater will be successful. To property set up your modem let all HepeaterTechnologies 0A products (including the OABOO, 0A550, and omens): 1. Connect to the repeater through the local Craft port Craft for the meme NR Chapter 3. Configuring OABSOC NR Properties — Page 17 Preliminary Draft — HTI Dormdemfal 2 ' Launch RepeaterNet. 3. Once the connection to the repeater has been established, select Conllgumtion from menu bar at the top of the screen. 4. From the Configuration menu, select Modern Propertles. 5. Click on the Modern Setting tab. 6. Enter 537=6 in the Modem lnlt String field (the top field on the Modem tab). 7. Enter a Phone Number; for example 9, (222) 123-4567. Each comma creates a 2-second delay in dialing. Parentheses () and spaces are ignored. 8. Enter the number of times you want RepeaterNet to attempt to make the connection; for example, 3; 0 (zero) in this field disables calling. 9. Click on Apply or OK at the bottom of the window. This procedure forces the repeater to initialize the modern to 2400 baud. which improves the connection on analog wireless networks. Changes made to the default settings on the Modem Properties screen take effect upon exiting FlepeaterNet. In addition: CI If you configure a repeater to automatically call out and repoit alarm status, the repeater COM port settings must match the settings of the modem to be called. El For users to log in to the repeater with a modem, the port settings of their computer‘s modern (defined in the configuration file) must match the settings of the repeater modem. D it the repeater is equipped with an internal modem. the setup string is controlled automatically by the repeater hardware. If the repeater is connected to an external modem, consult the modem’s documentation for the setup string. El Changes you make to the default settings on the Modem Properties screen take effect upon exiting RepeaterNel. Modem mam.” n msm “ms-mm Pdeh‘v-z Pager Setting You can set RepeaterNet to send out a page when a certain severity level alarrn occurs with the Pager Setting tab. A page is generated it the summary alarm severity is greater than or equal to the Mlnlmum Severity you select. When a page request is detected, the repeater terminates any current modem connection and generates a page. The page format consists of the repeater number followed by the severity level; for example, 123456-2. If a change in the current alarm severity is detected, note the following: D It the Mlnlmum Severity is set to Major and a Major alarm comes in, a page with a severity of 2 is generated. Craft for the OABsOC NR Chapter 3. Conflgun‘ng OA8500 NFl Properties — Page 18 Preliminary Draft — RTI Confidential D If a Critical alarm is detected, page is generated again with a severity of 3 (Critical plus Major). D If the Maior alarm is cleared but the Critical alarm remains. a page is generated with a severity ol 1 (Critical) El If the Critical alarm is cleared, a page is generated with a severity of 0, El If a Minor alarm is detected, no page is generated because the Minimum Severity is set to Major. 13 Events do not generate a page. Severity numbers are: No Alarms 0 Minor 4 Critical 1 Critical + Minor 5 Major 2 Major + Minor 6 Critical + Major 3 Critical + Major + Minor 7 To set a pager: 1. Click on the Pager Setting tab of the Modem Properties screen. 2. Enter the Pager Number, the number of times FlepeaterNet should attempt to call the pager number (Call Attempts), and the number of the repeater (Repeater Number). The Pager Number is the phone number to be called. This reflects the pager phone number, including networking access number (9), 1. and area code (if needed). Access the network dial number and wait 5 seconds before sending the page sequence. Several commas must follow the phone number—each comma generates a delay ol 1 second. Generally, it takes about 3 seconds for the pager company to pick up the line, and a maximum of 5 seconds before they drop the connection. A good delay would be 5 seconds. in which case you would add 5 commas; lor example. 9 1 (408) 555-1212.,,,, . Spaces, dashes, and parentheses are ignored. 3. Enter the Call Attempts, which are the number ol retry calls to be attempted. A value ol 0 in this field disables paging. 4. Enter the Repeater Number (a system identification number or description). 5. Select the minimum alarm severity for paging. Values can be Critical. Major, or Minor. 6. Click on Apply to set the values without exiting the properties screen; click on OK to set the values and exit. Cell Phone Properties From the Main Control screen Configuration menu, select Cellular Phone to open the Cell Phone Properties screen. The Alarms lab lets you set the alarm severity lor the Cellular Alarm. This alarm indicates a failure of a cellular phone. To change alarm severity: 1. Click the down-arrow next to an Alarm field to select a new alarm severity. Craft [or the 0A8500 NR Chapter 3. Configuring OABSOC NH Properties - Page 19 Pro/Mary Draft - RT! Confidential 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or OK. Severity levels include Disabled, Event, Minor, Motor, and Critical. NOTE: This severity should be minor. The Cell Phone alarm is generated when the cell phone fails to report an alarm after all retry attempts by either the modem or the pager, This alarm clears when the cell phone succeeds in reporting an alarm. When there is no cell phone, the Cell Properties selection is disabled. Power System Properties From the Main Control screen Configuration menu, select Power System to open the Power System Propertles screen. This screen lets you aocess initial configuration settings tor the power subsystem. Fledefine alarm severity tor Power systems using the Alanna Setting tab. 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or OK. Values are Disabled, Event, Minor, Maior, and Critical. The Alarm Setting tab lets you set the alarm severity of the lollowing alarms: input Power Alarm The input power to the repeater is out of system tolerances. Power Supply Alarm The internal system power of the repeater is out of tolerances. Battery Alarm The voltage at the internal battery is below tolerances. This battery supplies power to the ACU, modern, and cell phone in the event of a system power failure, letting the repeater call out and report its status. It also supplies power to the memory that stores the Alarm and Event Log. Battery Charger Alarm The internal battery charger is not charging the internal battery. NOTE: The internal battery does not provide power for RF components and the repeater will not be able [0 provide RF coverage during a power failure. Craft for the OA8500 NR Chapter 3. Conflgunng OA8500 NR Properties - Page 20 Preliminary Draft? HT! Confidential Backup Power System (UPS) Properties The UPS Properties screen lets you access initial configuration settings for the optional, external backup power supply. From the Main Control screen menu bar, select Configuration -> UPS to open the UPS Properties screen. Redefine alarm severity for backup power systems using the Alarms Setting tab. 1. Click the down-arrow next to an Alarm field to select a new alarm severity. 2. Click Apply or UK. Values are Disabled, Event, Minor. Major, and Critical. You can set the severity tor the following alarms: Ac Fail Alarm Indicates that the input power to the BUPS has tailed. in this case, the BUPS provides 40 or 80 amp- hours (depending upon which BUPS model is installed) of backup power for the repeater belore shutdown. (The AC source powers the charger.) Battery Low Alarm Indicates that battery voltage of the BUPS is below operating tolerances and the BUPS cannot power the repeater. Battery High Alarm Indicates that battery voltage of the BUPS is above operating tolerances and the BUPS cannot power the repeater. Charge Fail Alarm Indicates that the inlemal charger ol the BUPS has Iailed and the BUPS is unable to recharge its batteries. Summary Alarm Indicates that one or more of me BUPS alarms have been triggered. Tamper Alarm Indicates that the door of the BUPS is open. Craft for the memo NR Chapter 3. Configuring OAB500 NR Properties — Page 21 Preliminaly Draft 7 RT! Confidential Chapter 4. Monitoring OA85OC NR Status ’\ Monitor and control repeater system functions on subsystem Statue screens. Click a subsystem icon to open its Status screen. Each Status screen includes one or more of the following tabs: Alarms Reports present subsystem alarm states, with date and time stamps. Measurements Reports power and operational temperature measurements. including Low and High values A Reset Low/High button resets values. Voltages Reports present voltages for a subsystem. Control includes ONIOFF switches tor internal and extemel subsystem hardware Status screens for the OABSOC NR are: in Front End Status D Channel Status “4 Fitter Status (Forward and Reverse) W PA Status (Forward and Reverse) Alan-n Control Unit (ACU) Status Modern Status Cellular Phone Status Power System Status UPS Status lemma izmmm 1111111111 Front End Status Click an FFE (Forward Front End) icon to display the Front End Status screen. The Front End Status screen Alarm tab reports these elerms: Forward FE alarm Activated when the lorward signal power level is too strong and is bean attenuated to protect the repeater from possible damage. Reverse FE alarm Activated when the reverse signal power level is too strong and Is being attenuated to protect the repeater from possible damages. Craft for the 0AB500 NH Chapter 4. Monitoring OA85OC NH Status — Page 22 Preliminary Draft — HYI Con/iden Hal Diversity FE alarm Activated when the Diversity Receive signal power level is too strong and is being attenuated to protect the repeater from possible damage. mm“, anl Em: mm; Channel Filter Status Click a Channel 1 or Channel 2 tiller icon (sine waves) to open a filter Status screen, which reports a CSF1 Fumard Alarm (Forward Filter) and CSF1 Reverse Alarm (Reverse Filter) with date and time stamps. A failure in the Reverse or Fomard filter assembly triggers an alarm. Channel PA Status Click a Channel 1 or Channel 2 FPA or EPA icon to open a PA Status screen. PA Alarm Tab The PA Alarms tab reports subsystem alarms with date and time stamps: A failure in the Forward or Reverse PA assembly triggers an alarm. PA Measurement Tab The Channel 1 and Channel 2 PA Measurement tabs reports the output power at the repeater, including low and high output values. To reset low and high output values, click Reset Low/High. ACU Status Click the ACU icon to open the ACU Status screen. There are two tabs—Alarm and Measurement. Craft for the OASSOC NR Chapter 4.. Monitoring OABSOC NR Status — Page 23 Preliminary Draft — HTI Confidenlial ACU Alarm The Alarm lab reports subsystem alarms with date and time stamps. A lailure in the ACU assembly m... " _. ,. triggers an alarm. Eflfim'“ “‘ rm...“- The ACU alarms include: flTfiimmm External Input Alarms (1 end 2) An alarm generated lrom optional. external equipment. Temperature Alarm The system temperature threshold has been exceeded. Tamper Alenn The repeater door is open. Analog Input Alarm The upper or lower limits for monitoring ol the analog input DC voltage source have been exceeded. Measurement The Measurement tab reports current, low, and high system temperature and DC voltage source values. Click on the Reset LowIngh button to reset the low and high values. Modem Status Click the Modem icon to open the Modern Status screen, which reports a modern alarm with a date and time stamp. Internal modern component lailure triggers an alarm. Cell Phone Status Click the Cell Phone icon to open the Cell Phone Status screen, which reports a Cell Phone Alarm with a date and time stamp. Inlemal cellular phone component failure triggers an alarm. Craft for the OABSOC NR Chapter 4.. Monitoring OAESOC NFl Status - Page 24 Preliminary Dial? — RT! Confidential Power System Status Click the Power icon to open the Power system Status screen. This screen allows access to monitoring and operating tasks for the repeaters power subsystem. Alarm pm , 3mm Gimp The Alarms tab reports the status of the following alarms with severity, date, and time information tor each: an. [m ‘mwm human] thMAM Input Power Alarm as Blfiwflnmshtu inmznm rzwmm Indicates the input power to the repeater is out ol tolerances. Power Supply Alarm Indicates system power at the repeater is out at tolerances. Battery Alarm Indicates the voltage of the internal battery is out of tolerances. This battery supplies power to the ACU, modem, and cellular phone in the event of a system power failure, letting the repeater call out and report its status. It also supplies power to the memory that stores the Alarm and Event Log. Battery Charger Alarm indicates that the internal battery charger is not charging the internal battery. NOTE: The internal battery does not provide power r"FtF :.:,~ronents and the repeater wi/I not L , able to provide FtF coverage during a r-awer failure. Voltages The Voltages tab shows the current power values for Battery Volts. Channel 1 PA Volts, and Channel 2 PA volts. UPS Status The UPS status screen allows access monitoring of the optional. external backup power supply. This screen includes an Alarms tab, which displays the alarm status of the lollcwing alarms: AC Fail Alarm Indicates that the input power to the BUPS has failed. in this case, the BUPS provides 40 or 50 amp- hours (depending upon which BUPS model is installed) of backup power for the repeater before shutdown. (The AC source powers the charger.) graft for the OA85OC NFt Chapter 4.. Monitoring OABsOC NR Status - Page 25 Preliminary Draft — RTI Canfldellb'a/ Battery Low Alarm Indicates that battery voltage of the BUPS is below operating tolerances and the BUPS cannot power the repeater. Battery High Alarm Indicates that battery voltage 01 the m‘iflmfifi‘; BUPS is above operating tolerances and Egg-"Mm???“ the BUPS cannot power the repeater. mums.“ Charge Fail Alarm Indicates that the internal charger of the BUPS has failed and the BUPS is unable to recharge its batteries. Summary Alarm Indicates that one or more of the BUPS alarms have been triggered. Tamper Alenn Indicates that the door of the BUPS is opert Crafl for the OABSDC NR Chapter 4.. Monitoring OAasac NR Status — Page 26 Preliminary Draft — RTI Confidential Chapter 5. RepeaterNet Commands Commands available from the OABSOC NR Main Control screen’s menu bar are described in this chapter. File Menu—-OABSOC Craft Open the Main Control screen File menu to display the RepeaterNet commands described in this section. Download Properties You can download all settings previously uploaded to a repeater with the Download Properties command. You can use Download Properties to: El Download the default configuration file distributed with your Craft soitware to avoid having to manually configure each setting. u If you have used the Upload Properties command to store repeater configuration settings. The following preset configuration files are distributed with RepeaterNet Craft installation software and can be found by tollowing this path: Program Files -> Repeater Technologies -> HepeaterNet Craft 2.1 -> Contlg Files Configuration File Teonflgur-tion OA850C2_2_Chan,NMS.rci | OABSOC repeater without modem or phone OASSOCJAChan_ModemPhoneNMS.rct l OABSOC repeater with modem or phone To download settings to a repeater using the standard repeater configuration file: 1. From the Craft Main Control File menu, select Download Properties; a confirmation box is displayed to give you an opportunity to change your mind about the download operation. 5 Dirt! m»- it. w tore repeater pluuullu‘: lulu: 2. Click on OK to proceed; a Select file to restore box is displayed. ' Um_z_chm_Mn a. Select the repeater configuratlon file to MISWZZIJJthNMSJcI uAm_z_cm_nu4 whose properties you want to download. - misnuc_z_nm_uud-Mm.rd [in] fluently-armband 4. Click on Open to proceed with the DMIIII_1_Chan_Hndar-Fhotnl'agel.rd download. wnn,|_ctm_uus,ra Upload Properties new System settings are stored in a repeater may —fl configuration (.rcf) file, which you can use to download all settings from one repeater to additional repeaters in a network, or to configure a replacement unit. I] Ownnreadwb Once you have configured a repeater, you can upload the configuration from that repeater to your workstation with the Upload Properties command. You then can use the Download Properties command to copy the configuration to individual repeaters in your network. To upload system settings and create a repeater configuration file: Craft [or the 048500 NR Chapter 5. HepearerNet Commands -— Page 27 Prelinuhary Dre” — F177 Confidenlr'al 1.‘ Select a repeater and open Craft. 2. Select File->Upload Properties to open the Select a file to save repeater properties to dialog box. . HmniLLCthu-i t mm_l_cn~um rm .\ up in M». ”mu m. » m. flAlmJ_Ehar\_NI-d‘hwagel.rd IIMIIIII tan-Lu 3. Entera name for the file withoutafile extension. matron c , s, , man 2 on. n An .rcf extension is added automatically to the mt“:iMN:¢-';m=h;:m - ’ ‘ .._ " file name; tor example, filenamech. “Miami‘s-“f t . . . g k .v 4; ., ~ 4. Click Save to initiate the upload. ‘ ‘ rm r—fiq 11-23 5. Click OK when the upload is complete. Stu-cw awn- [blunt-[1rd] Save a copy of the repeater configuration file on a floppy disk for safekeeping. NOTES: El When you create a backup file, be aware that Repeater Configuration (Jo!) files created using a Network Monitor Iogin include IDs and passwords. D The Repeater Configuration (Jar) file is saved in the RepeaterNet program directory. Update Repeater Firmware Install a firmware upgrade with the Update Repeater Flrmwere command. Note that firmware updates are sent automatically to the designated point of contact for every effected owner of the repeater. Update “ packages are sent using overnight delivery and Include m‘m-l-m- WW” a detailed notice, a floppy disk, and installation unmet-mused instructions. Any questions concerning the update should be directed to the Repeater Technologies Customer Service Department. A A Toinstallatlrmware upgrade: sm'w [aflL—«fl—“bml—E [E] Erna-numb 1. Read documentation provided with the firmware upgrade. ’ 2. Login to a session with the repeater to be upgraded. 3. Insert the upgrade disk into the computer's floppy drive. 4. From the Main Control screen menu bar, select Flle—>Update Repeater Flrmware. An Open dialog box is displayed to let you save me repeaters configuration. You can choose to select a file into which the configuration should be saved, or click on Cancel to proceed with the firmware update. — To save the configuration and continue with the firmware update, select an Jot file and click Open. — If you do not want to save the repeater configuration, click on Cancel. Craft for the 048500 NR Chapter 5, Repeater/Vet Commands — Page 28 Preliminary Dre" —- Fm Confidential — Clicking Open or Cancel causes the upload operation to proceed; an Uploading Repeater window displays the progress of the upload. 5. When the upload is complete, the Select a tirmware tile to download to the repeater box is displayed. in the Look In box, select the drive in which the upload disk is located. 6. Double-click the upgrade file. It is labeled with an 509 extension—tor example, Iilename.509. The previous firmware version is overwritten. 7. When the upgrade is complete, the repeaters configuration is restored automatically lrom the file you chose in the Open dialog. ‘ ExIt The Exit command ends an active session with HepeaterNet and returns to the Welcome screen. Configuration Menu—OABSOC NR Craft initial configuration of the repeater is done from the Configuration menu commends. See Chapter 4. Configuring OABSDC NR Properties on page 10 for detailed information. System Menu—OABSOC NR Craft Open the System menu to display the Properties and Alarm and Event Log commands described in this section. Properties Select Properties lrorn the System menu to open the System Properties screen. NOTE: When the repeater is on a network, the system name must be entered to match that at the Network Management station in order for unsolicited alarms to be recognized System Tab Th s t ab Id d f Id l smls’m'mls’ww' e ye emt incu es ata is s or storing site- . specific information—the system name (name of the ”MN“ M repeater), brief site information (such as a network name sum; ow— — or city location), and the repeater phone number for a repeater with a modem option. 5M“ Entering summary data on the System Tab, although optional, is recommended As a minimum, type a name for the repeater In the System Name field: during automatic reporting, the repeater name is displayed in the title bar ct the Main Control screen, identifying the selected repeater. To record system data: 1. Type required information in the data fields. 2. Click Apply or OK. Craft for the OABSOC NR Chapter 5. RepeaterNet Commands — Page 29 Prelim/Wary Bren — HT! Confidential System Inventory Tab " The System Inventory tab includes data fields that provide information about the repeater to which you are connected. FtepeaterNet reads this information directly from the repeater upon successful Iogin. These Information-only fields are described as follows: Assembly Part Number 5m mlswmbfil The part number of the repeater (for example, 090-1200-09). mama Mm ,—_m_” Salaam r—'_, Serial Number The 9-digit serial number of the repeater. “m“ ' Dflte “a: HMAVSM e The date the repeater was built. WMVfiiw W“ Hardware Revision "mu am The repeater hardware revision (such as Rev. A) Firm-Wain Boot Code Version The version of the boot code installed in the repeater. Installed Options Optional internal equipment' in the repeater (such as a cell phone). Firmware Version The firmware version installed in the repeater. Login Tab Smmlsmmlmaluy swoon] The Logln tab includes fields to type in login IDs and “WW. mm ”M lwqul‘omm passwords and to configure the Auto-Logout function. cm: W— ,— ,u__::| In the Auto-Logout inactivity Timo field, define how W F— |———— P—g long RepeaterNet should wait, during a period of um ”I“ mm" inactivity, before terminating a session. A time interval Emir-v . _ i in minutes between 1 and 60 can be defined independently for each access level. If you enter a zero in a time field, this testure is disabled. NOTE: When the repeater is part of a network, the time field must be zero (0). To change a login ID or password: Login to the repeater (as an administrator). Select Properties”. from the System menu. Click the Logln tab. Type the new Iogin D or password (using six or fewer characters) into the appropriate fields. Write down Iogin IDs and passwords and secure in a safe place. Click Apply or 0K to set the new information. Notify affected operators of ID and password changes. rumpus-snows NOTE: When the repeater is networked, this information also must reside in the NMS Database. Craft for the OABSOC NH Chapter 5. RepeaterNet Commands - Page 30 Preliminary Draft - i777 Confidential Alarm and Event Log Open the Alarm and Event Log from the System menu to view the alarm and event history ol the OA1900 NH. The log is dynamically updated during viewing. Line entries in the Alarm and Event Log are organized as follows: 1. Subsystem affected by an alarm or event 2. Alarm severity 3. Date and lime stamp Saving , Printing, and Editing the Log Alarm and Event Log entries can be printed, saved, or edited using Notepad. Click on Run Notepad; a copy at the Alarm and Event Log is displayed in a Notepad window, in which you can edit the log. To print or save the log, select Prlnt or Save as... from the Notepad File menu. Options Menu—OABSOC NR Craft Open the Options menu to display the Color Independent Icons and Alarm Sounds RepeaterNet commands. Color Independent Icons Color Independent Icons are special graphic indicators designed to assist operators unable to distinguish colors. As part oi the alarm reporting system, Color Independent Icons display on the Main Control screen for a Critical, Maior, or Minor alarm. By default, the Color-Independent Icons feature is OFF. From the Main Control screen menu bar, select Options->Color Independent Icons to turn ON this leature. Color Inde endent Ioon Critical Alarm through subsystem ioon Major Alan-n through subsystem icon Minor Alarm through subsystem icon Craft for the OABSOC NR Chapter 5. RepeaterNet Commands — Page 31 Preliminary Draft ~ RTI Confident/at Alarm Sounds The Alarm Sounds leature allows for an intermittent alarm to activate when a subsystem triggers an alarm. By default, the Alarm Sounds feature is OFF. From the Main Control screen menu bar, select Alarm Sounds from the Options menu to turn ON this feature. NOTE: During an alarm, either clicking a subsystem icon to open the Status screen or clearing the alarm silences an audible alarm. - Hold Connect/on The Hold connection teature maintains the direct or dial-in connection to the repeater for monitoring until you terminate the connection. Help Menu—OASSOC NR Craft RepeaterNet on-Iine help is designed to provide quick access to information related to the operation of the repeater. D To open RepeaterNet Help, select Help->Help Toplcs. El To learn about the version of HepeaterNet Craft. RepeaterNet NMS, or RepeaterNet Administrator installed, select About... from the Help menu of any program window. Navigating Help a From the Contents tab. double-click a book icon to open its contents, then double-click a topic icon to open its Help page. A help page provides detailed topic information. Help pages can contain links— identified by green, underlined text~to related topics. D From the Index tab. type a topic name in the data field to automaticallyjump to a topic or use the scroll bar to locate a topic entry. Double-click an index entry to open its Help page. D Click the Index tab to open the Flnd Setup Wizard utility, which searches for specific words and phrases instead of searching by category. Follow the prompts. D To find out the version at RepeaterNet in use, select About from the Main Control screen Help menu. Exitlng RepeaterNet To exit HepeeterNet, return to the Main Control screen File menu and select Exlt. Craft for the OABSOC NR Chapter 5. RepeaterNet commends - Page 32 Preliminary Draft — RTI confide/ma, Appendix A. Default Alarm Settings subsystem Optian Alarm Default Setting Front End | Forward Fwd FE Alarm c | Reverse RevFE Alarm C lcal RevFEFrotect Alarm Critical | Diversity DiversityFE Alarm Critical Channel 1 Reverse PA Rev PA Alarm Critical —i Rev PA VSWR Alarm Disabled Rev PA Thermal Alarm Major Rev PA Ext Shutdown Alarm Disabled Forward PA Fwd PA Alarm Critical Fwd PA VSWR Alarm Disabled Fwd PA Thermal Alarm Major Fwd PA Ext Shutdown Alarm Disabled PA Conlrol Reverse PA OFF Forward PA OFF Reverse Filter CSF Rev Alarm Event Forward Filter CSF Fwd Alarm Gain Forward and Reverse 65DB Channel 2 Reverse PA Rev PA Alarm Critical Rev PA VSWR Alarm Rev PA Thermal Alarm Disabled Major Rev PA Ext Shutdown Alarm Disabled Forward PA Fwd PA Alarm Critical Fwd FA VSWR Alarm Disabled Fwd PA Thermal Alarm Major Fwd PA Ext Shutdown Alarm Disabled PA Control Reverse PA Forward PA Reverse Filter CSF Rev Alarm Forward Fitter CSF Fwd Alarm Event Alarm Control Unit (ACU) ("It external Inputs or equip- ment are used, sat alarm severity as appropriate.) External Input 1' Alarm External Input 2' Alarm Temperature Alarm Tamper Alarm Analog Input Alarm Ext. Growth Box Alarm Disabled Disabled Minor Major Disabled Disabled Power Supply Backup Power Sunpiy I Cell Phone Craft for the OA19000 NR r Channel PS Input Power Critical Power Supply Alarm Critical Battery Alarm Minor AC Fail Alarm Disabled Lew Battery Alarm Disabled High Battery Alarm Disabled Charge Fail Alarm Disabled UPS Summary Alarm Disabled Tamper Alarm Modem Alarm Cell Phone Alarm Disabled LMinor Appendix A. DelauItAIarm Settings — Page 33 Preliminary Dralt — RTI Confidential Appendix B. RepeaterNet Executables The installation program installs all necessary application executables and associated support drivers in a Windows lolder you select or, by delault, in c! \Px‘o§tlfl F11-B\Wltlr Teammate“ Repeat-mot. The installation program also prowdes entries into the system registry. The main RepeaterNet executable tiles are: CmflMmin . The Dalabase Administrator program used to configure and select the communications pout used by RepeaterNet Craft. RepeaterNet The Craft graphical user interface for different repeater hardware types. Used in the setting and viewing of individual repeater items. When any at these executable files are mnning. an icon is displayed on the Windows Task Bar. Craft for the 048500 NR Appendix B. RepeaterNet Executables — Page 34 ,.\ Preliminary Draft 7 HTI Confidential Appendix C. The Oki Cellular Phone Accessing the OKI Cellular Phone The cellular phone is located on the inside door of the OASSOC NFt entry box. Unscrew the four screws securing the metal box lid. in- Cellular | Phone NOTE: The AC charger and cellphone antenna are provided in the accessory kit. Programming the OKI Cellular Phone An abbreviated set of instructions for NAM programming at your Oki Phone is provided in this section. For more detailed information, see your OKI PHONES 1400 Series documentation. Programming Mode Access 1. Turn the power on and press Rcl + Func keys at the same time. 2. Enter your 5—digit special password within 30 seconds. 3. Alter the special password is logged in successfully, ESNIHEZ Number and Sottwm Version Number are displayed for two seconds each. 4. Two seconds later the Speed Dial Memory reset prompt is displayed. Craft for the OA8500 NH Appendix C. The Oki Ceiular Phone — Page 35 Preliminaly Draft - RT! Confidential 5.” Proceed to the next section, “Speed Dial Memory Clear," or press volume VA to scroll within the NAM Programming menu. Speed Dial Memory Clear Scroll the NAM Programming Menu until “Spd dial" appears n the display, followed by the reset prompt ("reset-0"). Press 0 to clear the Speed Dialing Memory. Detault Data Set Scroll the NAM programming menu until “det data“ appears on the display, followed bythe reset prompt (""reset-0'). Press 0 to reset all user programmable functions to the Manufacturer‘s default. Lock/Unlock Code Programming 1. Scroll the NAM Programming Menu until “Uloc and (current code)" appears on the display. The default is “1234.” 2. Enter a new 1-to-4 digit unlock code and press Sto key. Telephone Number Programming 1. In this menu, you can program information that is unique to Telephone #1. Follow the instructions or press Cir to skip to Telephone #2 or the next item on the main NAM Programming menu. 2. The display indicates “tel.no 1" tollowed’by the last seven digits ol the current phone number. Enter the new number (area code plus telephone number) and press Sto. Authentication Key Programming The display indicates "Auth.no.“ followed by “Emma." Enter the authentication key provided by the carrier (up to 26 digits) and press Sto. If an Invalid number is entered. the display shows I“not good" followed by “Entr.nc." Home SID Programming Enter a 5-dtglt SID number and press Ste. The IPCH Number Initial paging channel number is set automatically depending on the stored Horne SID number. ACCOLC Number The currem number is displayed. Enter a new number if required. then press Sto. GID Number 1. The current number is displayed. Enter a new number if required, then press Ste. 2. Press clr to return to the main NAM Programming menu. Emergency Number 1. The display shows “Help no." and the current setting. Enter a new number (up to 11 digits) If required. 2. Press Sto. Preferred SID Programming 1. Scroll the Preferred NAM Programming menu. Press Flcl and enter the desired Preferred SID number (5 digits). 2. Press Stu. You can enter up to 50 SID locations. Craft for the OABsOC NH Appendix C. The Oki Cellular Phone — Page 36 —\ Preliminary Draft— RTI Confidential 3.’ Press clr key to advance to the next programming option. Language Option Set Press Rcl and scroll through the available options. When the desired language is displayed. press sto. System Options Programming 1. Scroll the NAM Programming menu and press R131 to enter the Option Programmlng menu. 2. While in this menu, press ml to change settings and Stu tolsave and go on to the next setting. Press Clr at any time to return to the main NAM Programming menu. Option bits are defined astollows: 0 O 0 1 1 010 0 = ' Reserved for future use 0 = Reserved for future use 0 = Reserved for future use 1 = MINMK = Mobile ID Number Mark (0=No, 1=Yes) 1 = LUMK = Local Use Mark (0=No, 1=Yes) 0 = AMMK = Audio Mute Mark (0=Ca||, 1=Atways) 1 = HFMK = Handsfree Mark (0=No, 1=Yes) 0 = HAMK = Horn Alert Mark (0=No, 1=Yes) Craft for the OABSOC NR Appendix C. The Oki Cellular Phone — Page 37 Prellminary Draft - HT! Confidential Appendix D. Troubleshooting '\ The following attempts to identily the most common problems associated with the suocesslul operation of the RepeaterNet system. The steps listed to resolve the problem may not include all of the possible reasons for non-operability, but may assist in identifying the actual difficulty. The problem attributes in the following paragraphs have been ordered with the most likely problem listed first. If you continue to have problems, call Repeater Technologies Customer Support for assistance. See inside the front cover of this document for current telephone numbers. Problem 1: The FlepeaterNet Server reports that it cannot open the NMS database. Either the DSN is configured improperly, does not point to the proper location, or the system did not find the DSN itself. Call Customer Support for assistance. in The correct DSN or User ID is not identified. D The Windows ODBC drivers are not installed. CI The database file pointed to by the DSN is corrupted or needs repair. Problem 2: The Process Manager component of the HepeaterNet Server reports that It cannot read the database Ports table. No ports have been configured in the system database. The Ports table in the database may be corrupted. Repair the database and retry. Problem 3: The Syetem starts up without error but, when a repeater graphical user interface ls launched, no detailed data ls dlsplayed.. Wait for up to 4 minutes (cell modem connection) to see whether the program can connect to the repeater. It not, a warning will pop‘up indicating communications could not be established. Problem 4: A specific part does not seem to be in use and an Alert exists, or the database log reports the error “Unable to lnltiallzed port COMn” where n is the designation of the non-functionlng port. The port number has been configured incorrectly or the port does not exist. The port is assigned to another program operating in the same PC. Windows does not permit the sharing of communications ports between active programs. Shut down the other program. Problem 5: The system reports "Unable to connect to repeater... ” This can be an indication of: The cellular carrier is not handling me call The phone number provided is incorrect or out of service A problem with the modem or phone line A problem with the repeater EDGE Craft lor the OAGSOC NFl Appendix D. Troubleshooting — Page 38 Preliminary Draft - HT! Confidential Problem 6: The system reports the message "An unsupported operation was attempted.” This message appears When the installation lailed to register the OLE controls (or alarm bitmaps. Problem 7: RepeaterNet conflicts with Microsoft Fax. To disable the auto answer mode: 1. Open the mail icon from the Control Panel. Select Microsoft Fax from the Services tab. 3. Click on the Properties button. 4 Select either Manual or Don’t answer radio button. Click OK to save. Problem 8: NMs Client reports "cannot find app/[cation Repeat-met Server. ” This can occur when the Sewer is not running or a network leilure prevents the NMS Client from connecting to the Sewer. Verify that the Sewer is mnning and that the Sewer’s host is accessible. Another possibility is a conflict with the port assigned to the Sewer. This problem has been known to occur with a port number that previously had no conflict. Run the program “RepNetConfigexe’ in the RepeaterNet directory and increase the value of “Server Port" by one. Restart the Sewer and NMS Client. Craft for the OMEDC NH Appendix D. Troubleshooting — Page 39 P/elim/nary Draft ~ RT! Mnfldenlial End of Document On!!! for the memo NFI Appendbr D. Troubleshooting — Page 40 MK
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:07:11 19:29:23 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:07:11 19:29:25-04:00 Page Count : 88EXIF Metadata provided by EXIF.tools