Resmed Sleep Apnea Machine Apnealink Plus Users Manual

ApneaLink Plus to the manual 10b09fdc-05b9-4903-9787-380a4a89f420

: Resmed Resmed-Sleep-Apnea-Machine-Apnealink-Plus-Users-Manual-523817 resmed-sleep-apnea-machine-apnealink-plus-users-manual-523817 resmed pdf

Open the PDF directly: View PDF .
Page Count: 2

ApneaLink™ Plus

Patient Kit Instructions

Getting started

Before fitting, lay out all the system components and read these instructions first.

Note: Wear ApneaLink Plus and belt over pajamas or nightshirts with long sleeves, to avoid any

discomfort from the belt.

Fitting

English

Finger pulse sensor

Thread the belt through the brackets of the ApneaLink Plus and the

effort sensor. Fix the Velcro® fastener on the belt and move the

recorder to a comfortable position.

Wear the belt with recorder.

The easiest way to put on the

device is while standing in front

of a mirror.

Fit the nasal pressure cannula so that

the two small open tubes point towards

your nostrils. When doing this, ensure

that the ends point downwards.

Fit the loop around

your ears and then

back around your neck,

without pulling over

your head.

Draw the cannula to a comfortable

position under your chin. If tape or

adhesive pads have been provided

place them as indicated to help

secure the cannula.

Insert the index finger into the sensor. The finger

must reach the end of the sensor.

Recorder and sensor

1 2

6

�

�

Nasal cannula

3 4 5

Oximeter

Fit the pulse oximeter into the clip-on holder.

7

Recording

Disassembly

After stopping the recording, unscrew the nasal pressure cannula and remove the finger pulse sensor. •

Discard the nasal pressure cannula. •

Unfasten the chest belt with the ApneaLink Plus recorder and connected components. •

Carefully screw the protective cap back on the •nasal pressure cannula connection.

Detach the pulse oximeter from the recorder unit. •

Detach the finger pulse sensor from the pulse oximeter. •

Return or dispose of the finger pulse sensor as instructed by your Health Care Professional. •

Return the ApneaLink Plus together with the belt, oximeter, clip fastener and effort sensor back to •

your Health Care Professional.

Cleaning

Your Health Care Professional is responsible for cleaning the unit. Do not attempt to clean the unit. •

Intended Use

The ApneaLink Plus device is indicated for use by Health Care professionals (HCP) to aid in the diagnosis

of sleep disordered breathing. ApneaLink Plus records the following data: patient respiratory nasal

airflow, snoring, blood oxygen saturation, pulse and respiratory effort during sleep. The device uses these

recordings to produce a report that the HCP can use for diagnosis or for further clinical investigation.

CAUTION: U.S. Federal law restricts this device to sale by or on the order of a physician.

Global leaders in sleep and respiratory medicine www.resmed.com

Manufacturer: ResMed Germany Inc Fraunhoferstr. 16 82152 Martinsried Germany Manufacturer for Canada: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista

NSW 2153 Australia Distributed by: ResMed Corp 14040 Danielson Street Poway CA 92064-6857 USA ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14

4RY UK See www.resmed.com for other ResMed locations worldwide. Patents and designs pending. ApneaLink is a trademark of MAP Medizin-Technologie GmbH

©2009 ResMed Ltd. 228525/1 09 02

Attach the clip on the holder to

the belt. Insert the end of the

pulse oximeter cable into the

bottom of the recorder.

Start the recording in bed by pressing and holding the START/STOP

button for approximately two seconds, until the small light above the

button turns green. The ApneaLink Plus is recording when the green

lamp is on.

Stop the recording by pressing and

holding the START/STOP button for

approximately two seconds, until

the small light goes out.

8

10 min

The lamp will dim

10 minutes after

recording begins.

Start Stop

1..2.. sec

1..2.. sec

1 2

9

Remove and SAVE the protective cap from the nasal pressure cannula

connection. Fit the effort sensor tube and the end of the the nasal

pressure cannula to the connections of the recorder by turning it

clockwise.