Resolution RE159 Wireless Motion Detector User Manual

Resolution Products, Inc. Wireless Motion Detector

User Manual

360 Degree PIR Motion Sensor360 PIR Motion Sensor alarms when motion is sensed. It is a commercial battery-powered ceiling mount sensor with a 360 degree detection range. Features• 360° detection range with 62 distinct detection zones• Range up to 40 feet in diameter• Selectable pulse count 2 or 4• Designed for commercial application• 5 year warrantyEnroll by placing the panel into wireless enrollment mode and tripping the sensor’s enrollment sequence. Interlogix® , DSC®, Qolsys® and Cryptix™ variants can be enrolled by pulling the battery tab or by tampering the unit. Honeywell ® and 2GIG™ variants can be enrolled by tripping the unit three times (tamper or motion) or by holding the tamper down and powering the unit up by pulling the battery tab. Honeywell and 2GIG sensors must be enrolled as a “Loop1” sensor. Alternatively, all variants of the motion sensor can be enrolled by entering its serial number into the panel. Install by screwing two #8 screws into the ceiling, leaving 1/4 inch of thread exposed. Next, slide the back plate over the screws and rotate the back plate. Screw the third #8 screw through the wall tamper into the ceiling, ensuring that the wall tamper screw is attached to something solid. Tighten all screws until snug. Then, insert the square nut into the square slit of the cover and start threading the #4 screw into the side of the cover. Close the cover and conduct a walk test. After walk testing, take the unit out of walk test mode and close the cover again. Finally, nish threading the #4 screw until it is snug.Use your panel’s installation guide to verify proper system setup.INSTALLGUIDEIMounting Tips• Avoid direct sunlight• Avoid facing directly to AC or heating vents• Avoid vapor or high humidity• Avoid curtains, screens, etc. from blocking detection• Do not install outdoors
Sensor functions Alarm LED can be switched either “ON” or “OFF”.Pulse Count can be switched to either “2” or “4” mode depending on the environmental conditions of the installation.Walk Test Switch LED lights up when the unit has detected motion. An alarm signal is outputted whenever detection occurs.Normal Operation (Battery Saving Mode)LED lights up when the unit has detected if “LED ON” is selected. Once alarm is outputted, it does not output alarm again for 2 minutes. It goes back after 2 minutes and outputs alarm again when receiving detection signal.Detection RangePulse Count• Select “2” for normal applications.• Select “4” for use in areas where there may be movement by small animals or other objects, such as fax machines or curtains.
TroubleshootingProblem Probable Cause RemedyAlarm is not activated although someone is walking in detection areaDetection area is improper, battery is dead, Walk Test switch is OFF and 2 minute delay is activeConduct a walk test, change the batteryAlarm is activated with nobody in the areaMoving object within detection area, temperature of object within area is changing rapidlyRemove the object from the detection area, remove the heat sources from the detection area or relocate the detectorLED does not light up at the time of the walk testWalk test switch is OFF, battery is deadTurn the walk test switch ON, change the batteryLED does not light up in normal operationLED switch is OFF, battery is deadTurn LED switch ON, change batteryPro TipsSave battery life by taking unit out of walk test mode after completing walk test. There is no 2 minute delay when in walk test mode. Leaving in walk test mode will severely decrease battery unit life.Light changes will cause the sensor to trip. Ensure that the detector is not placed near windows. Sudden temperature changes will cause the sensor to trip. Ensure the motion detector is not placed near heating and cooling vents.High humidity environments can cause condensation of the detection lens. Ensure the motion detector is not installed in these kinds of environments. Protective lm should be removed from the lens after installation.Sensor Specications: The table below displays the functional frequencies of each compatible sensor.Part Number Frequency CompatibleRE159 319.5 Interlogix/QolsysRE259 345 HoneywellRE259T 345 2GIGRE359 433 DSCRE659 433 Cryptix
47-0047-00 • RevA • 2018-01-18 Tech Support Line (877) 260-5578www.ResolutionProducts.comWARRANTYResolution Products, Inc. will replace all non-portable products that are defective in their rst ve (5) years, and all portable products that are defective in their rst two (2) years.IC NOTICEThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:(1) This device may not cause interference, and(2) This device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux cnr d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:(1) L’appareil ne doit pas produire de brouillage, et(2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.IC: 8310A-RE159, 8310A-RE259, 8310A-RE359 FCC NOTICEThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference that may be received, including interference that may cause undesired operation.Changes or modications not expressly approved by Resolution Products, Inc. could void the user’s authority to operate this equipment.FCC ID: U5X-RE159, U5X-RE259, U5X-RE359 TRADEMARKSINTERLOGIX, HONEYWELL, 2GIG, QOLSYS, AND DSC ARE TRADEMARKS OWNED BY UNITED TECHNOLOGIES ELECTRONIC CONTROLS INC., HONEYWELL INTERNATIONAL INC., TYCO SAFETY PRODUCTS CANADA LTD, QOLSYS INC. AND NORTEK SECURITY & CONTROL LLC, RESPECTIVELY. RESOLUTION PRODUCTS, INC. PRODUCTS WILL FUNCTION WITH ONE OF EITHER INTERLOGIX (FORMERLY GE), HONEYWELL, DSC, OR 2GIG SYSTEMS. HOWEVER, NO RESOLUTION PRODUCT IS PRODUCED BY, ENDORSED BY, NOR IS OFFICIALLY ASSOCIATED WITH INTERLOGIX (FORMERLY GE), HONEYWELL, DSC OR 2GIG. RESOLUTION RECOMMENDS VERIFYING PROPER ENROLLMENT AND OPERATION, PER CONTROL PANEL INSTALLATION INSTRUCTIONS, AT INSTALLATION. SpecicationsPhysical Housing DimensionsWeight with BatteryMounting Fasteners4.72 x 1.57 inches (40 x 120 mm)4.2oz (120g)(3) #8 screws, (1) square nut, (1) #4 screw (All provided) EnvironmentalOperating TemperatureMaximum Humidity32°F to 120°F (0°C to 49°C) 85% non-condensing relative humiditySensor SpecicationsFrequenciesReplacement BatteryNominal Battery LifeBattery VoltageCurrent DrawDetection LengthDetectable SpeedTransmitted Indications433.92 MHz, 319.5 MHz, 345 MHzOne Panasonic CR123A Lithium Battery3 years (assuming 720 trips/day), 7 years (assuming 240 trips/day)3.3 VDC (Nominal), 2.4 VDC (Low)21 mA (Maximum), 4.7 uA (Standby), 30 mA (Max in walk test)Default: 16.5 feet (5m), Optional: 6.5 feet (2m)1 to 5 feet per second (0.3 to 1.5 meters per second)Motion, Tamper (Cover/Wall), Low Battery, SupervisionCerticationRE159, RE259, RE259T, RE359, RE659UL639, ULC-S306-03, ETL, FCC, ICSpecications subject to change without notice

Navigation menu