Resolution RE220-LS Wireless Security Sensor and Zwave Repeater User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2349473
Application ID	DE8a/itWOGJ2UhMu/TmcDw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.27kB (253338 bits)
Date Submitted	2014-08-06 00:00:00
Date Available	2014-08-07 00:00:00
Creation Date	2014-07-30 14:00:33
Producing Software	OpenOffice 4.0.1
Document Lastmod	0000-00-00 00:00:00
Document Title	User Manual
Document Creator	Writer
Document Author:	Benjamin Kyllo

RE220-LS Wireless Security Sensor and Zwave Repeater
Features:
• Listens to other Lifeshield wireless devices and senosrs, and re-transmits them to the
main control panel.
• Extends range of system.
• No enrollment required to start repeating sensor signals.
• Received ID's are passed on unchanged to the security panel. All sensor alarms,
supervisory, and trouble signals are passed through.
• Repeater has its own unique ID for supervisories, complete reporting of main device
tamper, external power supply fault and low battery if desired.
• Dual antennas for both Receive and Transmit diversity for increased range.
• Back-up battery protects during loss of external power.
• After simple inclusion into an existing Zwave network, will act as active listening
repeater Zwave device on the network filling in range gaps between other distant
devices.
Key Instructions:
• Attached external supply.
• Install internal battery backup.
• Enroll sensors into panel as normal, the repeater should be transparent to other
devices.
• Optionally enroll repeater into security panel:
◦ Put security panel into enrollment mode, then press the red reset button on the
repeater. This will put the repeater into enrollment mode to report back
supervisories, battery information and tamper conditions.
• To repeat zwave signals, repeater must be enrolled into local network.
◦ Put zwave into enrollment mode on the security panel, then press the red reset
button on the repeater. This will also put the zwave repeater into enrollment
mode to be included onto the local network.
LED Operation:
• Blue LED indicates power
• Green LED flashes to indicate a security sensor signal was received
• Red LED flashed to indicate that signals are being sent out (repeated)
Specifications:
Lifeshield Wireless Sensor
and Zwave Repeater User Manual
www.lifeshield.com
Page 1 of 3
•
•
•
•
•
External power supply: 5VDC. If using different supply, 100mA minimum required.
Battery backup: 2600mAh Li-ion 3.7V 18650 rechargeable battery
Dimensions and weight: 9 x 5 x 1.375”, 13.2oz
Internal antennas
Zwave chip: Zensys ZM5202
Speaker
Grill for
Alarm sounds
LED Window
Reset, and
Enrollment
Button
Lifeshield Wireless Sensor
and Zwave Repeater User Manual
External
Power supply
Connector
www.lifeshield.com
Page 2 of 3
Notices:
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Engineering, Inc.
or Lifeshield Inc. could void the user's authority to operate this equipment.
FCC ID: U5X-RE220-LS
Model: RE220-LS
Lifeshield Wireless Sensor
and Zwave Repeater User Manual
www.lifeshield.com
Page 3 of 3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Language                        : en-US
Author                          : Benjamin Kyllo
Creator                         : Writer
Producer                        : OpenOffice 4.0.1
Create Date                     : 2014:07:30 14:00:33-05:00

EXIF Metadata provided by EXIF.tools