Resolution RE311 Micro Door Window Sensor, 433.92MHz User Manual RE311 DSC Compat Micro DWS Instructions

Download:
Mirror Download [FCC.gov]
Document ID	1700455
Application ID	h2mQsciFv0K9ic83Um1adA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.06kB (375764 bits)
Date Submitted	2012-05-17 00:00:00
Date Available	2012-05-18 00:00:00
Creation Date	2012-05-13 13:51:41
Producing Software	GPL Ghostscript 8.64
Document Lastmod	2012-05-13 13:51:41
Document Title	RE311_DSC-Compat_Micro-DWS_Instructions
Document Creator	PDFCreator Version 0.9.8
Document Author:	bseemann

Enrolling in Panel
Wireless
Security
Solutions
1. Pull out the red tab to power the sensor.
RE311 Mighty Mouse™ DSC-Compatible Micro Door Sensor
Features
•
•
•
•
•
1.
Smallest Door/Window Sensor & Magnet in the Industry.
Full-sized transmit range, AND…
4-6 year battery life on CR1632 battery.
Invisible external antenna – gives great range and long life
Low Battery indication.
Align
centering marks
Mounting
2.
½ inch or less
magnet gap
2. Put DSC panel in Wireless Enrollment Mode.
3. Open (alarm) the DWS that you want to enroll.
Remove
High Bond
tape liners
4. Confirm ESN, Enter Zone # and Zone Type on DSC Panel.
5. May also be enrolled via entering ESN.
Position Antenna free and clear of sensor;
not inside cover or under sensor.
4.
wipe it down
with finger
Sensor sends
enrollment
signal
Open (Alarm) the
Sensor
3.
Run a light coat of
permanent paste
glue on the
underside of the
antenna
Internal Picture
Battery
contacts
Battery
Minus side up
Reed Switch
Antenna Routing Options
A. Fasten with paste glue, as above.
B. Or let it lay on surface, nearly invisibly.
DON’T MOUNT
ON METAL,
It will severely
reduce transmit
range and
magnetic gap
Antenna
C. Route into trim gaps or
along side of trim
D. Drill hole and
thread antenna down
RE311_DSC-Compat_Micro-DWS_Instructions.doc
Page 1 of 4
RE311_DSC-Compat_Micro-DWS_Instructions.doc
13-May-12
www.ResolutionProducts.com
Page 2 of 4
13-May-12
www.ResolutionProducts.com
Opening Cover
Specifications
Magnet trip distance:
Supervisories:
Battery Life:
Mounting fastener:
Replacement Battery:
Temperature Range:
Housing dimensions:
Antenna dimension:
1 inch nominal
Hourly
4+ years
3M VHB (Very High Bond) Tape
CR1632
0F to 120F
1.75 x 0.75 x 0.2 inches
2 inches
Specifications subject to change without notice.
Insert
Screwdriver
in slot
Notices
“GE”, “Honeywell”, “DSC” and “Napco” are trademarks owned by General Electric Company,
Honeywell International Inc., Tyco Safety Products Canada LTD, and NAPCO Security Systems,
Inc., respectively.
Tilt cover open.
Hinge is in back away
from antenna
Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco
systems. However, no Resolution product is produced by, endorsed by, nor is officially associated
with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and
operation, per control panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first year.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.
TO CLOSE
slide cover jaw into hinge.
Tilt closed.
Changes or modifications not expressly approved by the Resolution Products, Inc. could
void the user's authority to operate this equipment.
Replacing Battery
FCC ID: U5X-RE311
Insert Screwdriver
in slot.
Twist.
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
Note small
retention post
Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interférences, et
2. Ce dispositif doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
IC: 8310A-RE311
RE311_DSC-Compat_Micro-DWS_Instructions.doc
Page 3 of 4
RE311_DSC-Compat_Micro-DWS_Instructions.doc
13-May-12
www.ResolutionProducts.com
Page 4 of 4
13-May-12
www.ResolutionProducts.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : 30c1fe07-9f88-11e1-0000-ef064fa7b360
Producer                        : GPL Ghostscript 8.64
Keywords                        : ()
Modify Date                     : 2012:05:13 13:51:41-05:00
Create Date                     : 2012:05:13 13:51:41-05:00
Creator Tool                    : \376\377\000P\000D\000F\000C\000r\000e\000a\000t\000o\000r\000 \000V\000e\000r\000s\000i\000o\000n\000 \0000\000.\0009\000.\0008
Document ID                     : 30c1fe07-9f88-11e1-0000-ef064fa7b360
Format                          : application/pdf
Title                           : \376\377\000R\000E\0003\0001\0001\000_\000D\000S\000C\000-\000C\000o\000m\000p\000a\000t\000_\000M\000i\000c\000r\000o\000-\000D\000W\000S\000_\000I\000n\000s\000t\000r\000u\000c\000t\000i\000o\000n\000s
Creator                         : \376\377\000b\000s\000e\000e\000m\000a\000n\000n
Description                     : ()
Author                          : bseemann
Subject                         : 

EXIF Metadata provided by EXIF.tools