Resolution RE701 Outdoor Bullet Camera User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4207522
Application ID	iGiSr6FqPKqBRM8OdDM01g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	79.04kB (987949 bits)
Date Submitted	2019-03-20 00:00:00
Date Available	2019-03-20 00:00:00
Creation Date	2017-10-20 14:48:38
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2018-09-20 16:34:08
Document Title	Users Manual
Document Creator	Adobe InDesign CS6 (Windows)

Outdoor Bullet Camera
Quick Start Guide
SAVE THIS MANUAL FOR FUTURE REFERENCE
Setup
Step 1 Power-on
Plug the power cable into the camera and to the power adapter
and then into a power outlet, as shown in the figure below. The
LED indicator will flash red and blue, or rapid blue when the
camera is ready for setup.
Power Cable
Power Socket
Step 2 Camera Setup
- Add a camera to the Alula app
• Log in to your account using the Alula app.
• From the Alula app Camera screen, tap “+” on
the upper-right hand corner to go to the scan QR
code interface.
- Scan the QR Code on the bottom of the camera.
- Enter the verification code located on the bottom of the camera.
- Follow the app wizard to finish Wi-Fi configuration.
If you want to change your camera's Wi-Fi, press and
hold the reset button for 10s and repeat this part.
- Scan the QR code on the body of the camera.
Step 3 Choose network connection
- Choose Wi-Fi (2.4GHz Wi-Fi Only) or wired connection.
(Recommended) For Wi-Fi connection, enter Wi-Fi name
and password to configure Wi-Fi for the camera.
Router
N3
For wired connection, connect the camera to the router with a
network cable.
N3
Network Cable
- Enter the correct time zone and date format.
If the memory card status displays as Uninitialized, tap to
initialize it.
Hold the RESET button for 10 seconds when camera is
running if either adding cameras or Wi-Fi connection fails.
Step 3 Camera Installation
You can install the camera on the wall
or ceiling.
Make sure the wall is strong enough to withstand three times the
weight of the camera.
1 Installing the Camera
- Place drill template onto the surface you have chosen to mount
the camera.
- (For the cement wall/ceiling only) Drill screw holes according to
the template, and insert three expansion screws.
- Use three metal screws to fix the camera base according to the
template.
Mounting
Template
Expansion Screws
Metal Screws
2 Adjusting the Surveillance Angle
- Loosen the adjusting screw.
- Adjust the surveillance angle as your
desired place.
- Tighten the adjusting screw.
Make sure the microSD card slot facing downward.
Adjusting Screw
0°-90°
0°-360°
Appendix
Box Content
Power Adapter x1
Internet Camera x1
Quick Start Guide x1
Mounting Template x1
Screw Kit x1
Waterproof Kit x1
Basics
MIC
MicroSD
Card Slot
RESET
Speaker
LED Indicator
Name
Description
MIC
For audio in.
Speaker
For audio out.
LED Indicator
• Steady Red: Camera is starting up.
• Steady Blue: Video is being viewed or played back in
Alula App.
• Slowly Flashing Blue: Camera is running properly.
• Slowly Flashing Red: Wi-Fi connection has failed.
• Fastly Flashing Red: MicroSD card error.
• Flashing Red and Blue OR Rapidly Flashing Blue:
Camera is ready for the Wi-Fi connection.
MicroSD Card Slot MicroSD card not included in the Box Contents.
Recommended compatibility: Class 10, Max.128GB.
After inserting the microSD card, initialize it in the
Alula app, and then video files can be stored in the
SD card.
Hold the RESET button for 10 seconds when the
RESET
camera is running. The camera restarts, and resets all
Power Input
parameters to default.
1A
12V
Troubleshooting
Q:
A:
“The device is offline.” or “The device is not registered.” prompts
when adding
the camera by Alula app.
1. Make sure the network, that the camera is connected to, is
normal and the DHCP of router is enabled.
2. Hold down the RESET button for 10 seconds to reset the
parameters if you manually changed the network parameters.
Q:
A:
How to use the microSD card for local storage?
1. Make sure there is a microSD card inserted and the camera is
added to your Alula account. Log in the Alula app and enter
the “Device Details” interface, if the “Initialize Storage Card”
button appears, you need to initialize the microSD card first.
2. The microSD card recording for the motion detection is
enabled by default.
Q:
The mobile phone cannot receive alarm prompts when the
camera is online.
1. Make sure the Alula app is running on your mobile phone
and the Motion Detection Notification is enabled.
A:
2.For Android system, make sure the app is running in
background; and for iOS, enable the message push
function in “Settings > Notification”.
3. If still no alarm prompts, hold down the RESET button for
10 seconds restore the camera settings.
Q:
A:
Live view or playback failed.
Make sure your network is well connected. Viewing live video
needs a good
bandwidth. You can refresh the video, or change a network and
try again.
Q:
A:
How to connect to another Wi-Fi?
Hold the RESET button on the camera for 10 seconds to reset and
restart the camera and reconnect the Wi-Fi about 1 minute later.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Note: This product has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This product generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this product does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment complies with FCC/IC RSS-102 radiation exposure limits
set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator & your body.
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radioexempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
This equipment complies with FCC/IC RSS-102 radiation exposure limits
set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator & your body.
ce matériel est conforme aux limites de dose d'exposition aux
rayonnements, FCC / CNR-102 énoncée dans un autre
environnement.cette eqipment devrait être installé et exploité avec
distance minimale de 20 entre le radiateur et votre corps.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2017:10:20 14:48:38+08:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2018:09:20 16:34:08-05:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2018:09:20 16:34:08-05:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:201b403e-7e0c-4c37-abcb-e43e16cb0c76
Original Document ID            : xmp.did:31007AAE4FE4E511A0AD9065752CEC3D
Document ID                     : xmp.id:01F1D6B362B5E711B69CFBFDF8FFFFD4
Rendition Class                 : proof:pdf
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2017:10:20 14:48:38+08:00
Derived From Instance ID        : xmp.iid:2819A499B8B4E7118F32C36165692600
Derived From Document ID        : xmp.did:31007AAE4FE4E511A0AD9065752CEC3D
Derived From Original Document ID: xmp.did:31007AAE4FE4E511A0AD9065752CEC3D
Derived From Rendition Class    : default
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 10

EXIF Metadata provided by EXIF.tools