Rheem Classic Series 80 Afue 2 Stage Psc Motor Submittal Sheet

: Rheem Rheem-Classic-Series-80-Afue-2-Stage-Psc-Motor-Submittal-Sheet-683804 rheem-classic-series-80-afue-2-stage-psc-motor-submittal-sheet-683804 rheem pdf

Open the PDF directly: View PDF .
Page Count: 3

SUBMITTAL COVER SHEET

Quantity

Unit Designation

Model No.

Total Cooling

Sensible Cooling

Air Ent. Evaporator

Air Lvg. Evaporator

Heating Input

Heating Output

CFM/ESP

EER/SEER

Electrical

Minimum Ampacity

Min.-Max. Breaker

Net Unit Weight

Accessory

Catalog Form Number

ACCESSORIES: NOTES:

PRINTED IN U.S.A 01/12 QG FORM NO. M11-1640

PROJECT NAME

LOCATION

ARCHITECT

ENGINEER

CONTRACTOR

SUBMITTED BY DATE

UNIT SUMMARY

FORM NO. X33-1385 REV. 1

Supersedes Form No. X33-1231

JOB NAME MODEL NO.

CONTRACTOR OUTDOOR UNIT MODEL NO.

ENGINEER LOCATION

SUBMITTED FOR APPROVAL RECORD ORDER NO.

DATE

FEATURES FOR RGLQ-

■Patented heat exchanger, constructed of aluminized steel for the

maximum in corrosion resistance and thermal fatigue reliability.

■Low profile “34 inch” [864 mm] design is lighter and easier to

handle, and leaves room for optional equipment.

■Left or right side gas and electric inlet connections with quick,

simple change.

■Direct spark ignition.

■Integrated control board with humidifier and electronic air

cleaner hookups.

■Insulated blower compartment, a two stage gas valve and a

specially designed two speed draft inducer motor make it one

of the quietest furnaces on the market today.

■Pre-paint galvanized steel cabinet.

■Grab-holes in doors to aid in easy door removal and replacement.

■Compatible with single or two-stage thermostat. (For optimal

performance, two-stage thermostat recommended.)

✝A.F.U.E. (Annual Fuel Utilization Efficiency) calculated in accordance with Department of Energy test

procedures.

FIELD INSTALLED ACCESSORIES

Fossil Fuel Kit (RXPF-F01 and F02) ........................................

Filter Rack (RXGF-CCM) ..........................................................

Combustible Floor Base (RXGC-B14, 17, 21, 24) ....................

UNIT DATA

HEATING PERFORMANCE

TOTAL CAPACITY INPUT* ...... _______ MBH [kW]

TOTAL CAPACITY OUTPUT* .. _______ MBH [kW]

DESIGN TEMP. RISE .............. _______ °F [°C] DB

AFUE ................................................ _______ %

CALIFORNIA SEASONAL

EFFICIENCY .................................. _______ %

(*uses blower motor heat)

SUPPLY AIR BLOWER PERFORMANCE

TOTAL AIR SUPPLY ................ _______ CFM [L/s]

TOTAL RESISTANCE EXTERNAL

TO UNIT...................................... _______ IWG

BLOWER SPEED .......................... _______ RPM

POWER OUTPUT REQUIREMENT .. _______ BHP

MOTOR RATING ........................ _______ HP [W]

POWER INPUT REQUIREMENT........ _______ kW

ELECTRICAL DATA

POWER SUPPLY...................... ____________ Hz

TOTAL UNIT AMPACITY................ _______ AMPS

MINIMUM WIRE SIZE .................... _______ AWG

MAXIMUM OVERCURRENT DEVICE

FUSES/HACR BREAKER .......... _______ AMPS

CLEARANCES

FRONT SIDE 3" [76.2 mm]

RIGHT SIDE 3" [76.2 mm]

LEFT SIDE 0" [0 mm]

TOP 1" [25.4 mm]

TWO-STAGE DOWNFLOW GAS FURNACES:

RGLQ- Series

80% A.F.U.E.✝

Input Rates 50 to 150 kBTU [15 to 44 kW] (U.S. & Canadian Models)

DOWNFLOW MODELS

DOWNFLOW WARNING: Unit design is certified for

installation on non-combustible floor. A special

factory supplied combustible floor sub-base is

required when installing on a combustible floor.

Failure to install the sub-base may result in fire,

property damage and personal injury.

NOTES: ➀May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter.

➁ May be 0" [0 mm] with type B vent.

➂May be 1" [25 mm] with type B vent.

Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1

and/or Can/CGA-B149 Installation Codes and in accordance with local codes.

DIMENSIONS AND CLEARANCE TO COMBUSTIBLE MATERIAL (INCHES) [mm]

COMBUSTIBLE FLOOR BASE DIMENSIONS

MODEL

RGLQ- A B C D E

REDUCED CLEARANCES (IN.) [mm]

05 14 [356] 1227/32 [326] 103/8[264] ➀131/8[333] 04 [102] ➁01 [25] 3 [76] 6 [152] ➂

LEFT

SIDE

RIGHT

SIDE BACK TOP FRONT VENT SHIP. WGTS.

(LBS.) [kg]

85 [38.6]

07 171/2[445] 1611/32 [415] 121/8[308] ➀165/8[422] 03 [76] ➁01 [25] 3 [76] 6 [152] ➂105 [47.6]

10 (A) 171/2[445] 1611/32 [415] 121/8[308] ➀165/8[422] 03 [76] ➁01 [25] 3 [76] 6 [152] ➂115 [52.2]

10 (B) 21 [533] 1927/32 [504] 137/8[352] ➀201/8[511] 0001 [25] 3 [76] 6 [152] ➂120 [54.4]

12 241/2[622] 2311/32 [593] 155/8[397] ➀235/8[600] 0 0 0 1 [25] 3 [76] 6 [152] ➂140 [63.5]

15 241/2[622] 2311/32 [593] 155/8[397] ➀235/8[600] 0 0 0 1 [25] 3 [76] 6 [152] ➂150 [68]

COMBUSTIBLE

FLOOR BASE

A

IN. [mm]

B

IN. [mm]

USE WITH

FURNACE SIZES

RXGC-B24 25 [635] 233/4[603]

(-)GLQ-12, (-)GLQ-15

RXGC-B14 141/2[368] 131/4[337]

(-)GLQ-05

RXGC-B17 18 [457] 163/4[425](-)GLQ-07, (-)GLQ-10A

RXGC-B21 211/2[546] 201/4[514](-)GLQ-10B

C

IN. [mm]

213/4[552]

111/4[286]

143/4[451]

181/4[464]

[    ] Designates Metric Conversions

Before proceeding with installation, refer

to installation instructions packaged

with each model, as well as complying

with all Federal, State, Provincial, and

Local codes, regulations, and practices. Rheem Sales Company, Inc.

P.O. Box 17010, Fort Smith, AR 72917

“In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.”

PRINTED IN U.S.A. 10-13 QG FORM NO. X33-1385 REV. 1

Supersedes Form No. X33-1231