Rhine Electronics Co 7080T Remote Control Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	238437
Application ID	n6RVLyvogjxEiwQrsVukXQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.75kB (46915 bits)
Date Submitted	2002-04-23 00:00:00
Date Available	2002-04-23 00:00:00
Creation Date	2002-03-30 14:38:32
Producing Software	Acrobat 5.0 Scan Plug-in for Windows
Document Lastmod	2002-03-30 14:38:46
Document Title	User Manual
Document Creator	Acrobat 5.0 Scan Plug-in for Windows

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
1.This unit operates on a 9 volts battery (not included).
To prevent possible damage if the battery should leak , be sure to remove
the battery when the unit is not use .
2. Store the controller away from excess heat or humidity .
3. This remote control unit is requipped with 16 code combinations, To prevent
possible interference from or to other remote units such as garage door
openers, car alarm or security system A If you find that your fan and light
kit go on and ofi'without using your control , simply change the combination
code in your transmitter and receiver .
4.0peration buttons on the panel of transmitter A
HIGH key - For fan High speed A
MED key — For fan Medium speed .
LOW key — For fan Low speed .
OFF key — For fan speed off .
REV key — For fan speed Reverse .
LIGHT CONTROL key — For light brightness and ON/OFF control .
5.Start the fan :
Press the selected speed button to run the fan at the desired .
6rTum off the fan :
Press the OFF button .
7.Light control :
Turn the light on or off by only touching the LIGHT CONTROL button .
Keep pressing the button in excess of 0.7 second it becomes a dimmer ,
the light varies cyclically in 0.8 second .
One of the important feature of this control is AUTO-RESUME . Afier power
on , it allows the light return to where it was ofl‘ .
Page : 3-l
GENERAL INFORMATION :
This REMOTE controller is designed to separetly control your
ceiling fan speed and light brightness . The Light
ON/OFF button will control the light brightness ON/OFF .
The red indicator on the transmitter will light when the button is pressed .
INSTRUC'HONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER
Al Setting the code on your new transmitter .
1. Remove battery cover .
Press firmly below arrow and slide battery cover off .
2. Slide code switches to your choice of UP and DOWN position .
Factory setting is all UP l Do not use this setting .
Use ball point pen or small screwdriver .
Slide firmly up or down .
Bi Setting the code on your new Receiver unit .
1. Slide code switches to the same positions as set on your transmitter .
They must be set to same positions to work .
2. Replace battery cover on transmitter .
3. Make sure the code switches are on the left positions .
NOTICE :
The changes or modifications not expressly appproved by the
party responsible for compliance could void user’s authority
to operate the equipment .
Page : 3-1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2002:03:30 14:38:46+08:00
Create Date                     : 2002:03:30 14:38:32+08:00
Creator                         : Acrobat 5.0 Scan Plug-in for Windows
Page Count                      : 2
Mod Date                        : 2002:03:30 14:38:46+08:00
Creation Date                   : 2002:03:30 14:38:32+08:00
Producer                        : Acrobat 5.0 Scan Plug-in for Windows
Metadata Date                   : 2002:03:30 14:38:46+08:00

EXIF Metadata provided by EXIF.tools