Rhine Electronics Co 7082TA Transmitter of Remote Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2481838
Application ID	WNtGeR924+71xJJXvMTP2A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.12kB (126552 bits)
Date Submitted	2014-12-23 00:00:00
Date Available	2014-12-23 00:00:00
Creation Date	2014-12-07 12:44:56
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2014-12-07 12:44:56
Document Title	Microsoft Word - UC7082TA使用手冊
Document Creator	PScript5.dll Version 5.2.2
Document Author:	dorisgao

INSTRUCTIONS FOR OPERATION
MODEL: UC7082TA
SETING THE OPERATING CONTROLS
1.This unit operates on a 12 volts battery (not included).
To prevent possible damage if the battery should leak , be sure to remove
the battery when the unit is not use .
2. Store the controller away from excess heat or humidity .
3. This remote control unit is requipped with 65536 code combinations. To prevent
possible interference from or to other remote units such as garage door
openers, car alarm or security system . If you find that your fan and light
kit go on and off without using your control , simply change the combination
code in your transmitter and receiver .
4.Operation buttons on the panel of transmitter .
HIGH key – For fan High speed .
MED key – For fan Medium speed .
LOW key – For fan Low speed .
OFF key – For fan speed off .
REV key – For fan speed Reverse .
UP LIGHT CONTROL key – For light brightness and ON/OFF control .
DOWN LIGHT CONTROL key – For light brightness and ON/OFF control .
5.Start the fan :
Press the selected speed button to run the fan at the desired .
6.Turn off the fan :
Press the OFF button .
7.Light control :
Turn the light on or off by only touching the LIGHT CONTROL button .
Keep pressing the button in excess of 0.7 second it becomes a dimmer ,
the light varies cyclically in 0.8 second .
One of the important feature of this control is AUTO-RESUME . After power
on , it allows the light return to where it was off .
GENERAL INFORMATION :
Page : 3-1
This REMOTE controller is designed to separetly control your
ceiling fan speed and light brightness . The Light
ON/OFF button will control the light brightness ON/OFF .
The red indicator on the transmitter will light when the button is pressed .
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER
A. Setting the code on your new transmitter .
1. Remove battery cover .
Press firmly below arrow and slide battery cover off .
2.
Slide code switches to your choice of UP and DOWN position .
Factory setting is all UP . Do not use this setting .
Use ball point pen or small screwdriver .
Slide firmly up or down .
B. Setting the code on your new Receiver unit .
1. Slide code switches to the same positions as set on your transmitter .
They must be set to same positions to work .
2.
Replace battery cover on transmitter .
3.
Make sure the code switches are on the left positions .
NOTICE :
The changes or modifications not expressly appproved by the
party responsible for compliance could void user’s authority
to operate the equipment .
The term “IC:” before the radio certification number only signifies that Industry Canada Technical
specifications were met.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATIONS IS SUBJECT
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFEERENCE THAT MAY CAUSE UNDESRIED OPERATION.
age : 3-2
FCC
INFORMATION
The Federal Communication Commission Radio Frequency Interference
Statement includes the following paragraph:
The equipment has been tested and found to comply with the limits for a C lass
B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed
To provide reasonable protection against harmful interference in a residential
Installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communication. However, there is no grantee that
Interference will not occur in a particular installation. If this equipment dose cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
The user should not modify or change this equipment without written approval
Form RHINE ELECTRONIC CO.,LTD .Modification could void authority to use this equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : dorisgao
Create Date                     : 2014:12:07 12:44:56+08:00
Modify Date                     : 2014:12:07 12:44:56+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : dorisgao
Title                           : Microsoft Word - UC7082TA使用手冊
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:e4839773-3a3f-44e4-8b97-3fce6d8ca2f1
Instance ID                     : uuid:5dd9be57-66b4-4840-85d0-a3ef8cdc26c9
Page Count                      : 3

EXIF Metadata provided by EXIF.tools