Rhine Electronics Co 7216T Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3397193
Application ID	cxhNpal2HvNuO/7tSoLg7g==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.81kB (410173 bits)
Date Submitted	2017-05-19 00:00:00
Date Available	2017-05-19 00:00:00
Creation Date	2017-03-29 08:11:35
Producing Software	OpenOffice 4.1.1
Document Lastmod	0000-00-00 00:00:00
Document Title	Users Manual
Document Creator	Writer
Document Author:	ETC

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
1. This unit operates on a 3 volts battery (not included).
To prevent possible damage if the battery should leak , be sure to remove
the battery when the unit is not use .
2.
Store the controller away from excess heat or humidity .
3.
This remote control unit is required with 12bit code combinations. To prevent
possible interference from or to other remote units such as garage door
openers, car alarm or security system .
4. Operation buttons on the panel of transmitter .
FAN HI button – fan speed HI
FAN MED button – fan speed MED
FAN LOW button – fan speed LOW
FAN OFF button - FAN OFF
LIGHT button - Light ON/OFF or Dimmer
5. Start the fan
Press the FAN speed button .
6. Turn off the fan :
Press the OFF button .
7. Light control :
Turn the light on or off by only touching the LIGHT CONTROL button .
Keep pressing the button in excess of 0.7 second it becomes a dimmer ,
the light varies cyclically in 0.8 second .
GENERAL INFORMATION :
910805
This REMOTE controller is designed to separately control your
ceiling fan speed and light brightness . The Light
ON/OFF button will control the light brightness ON/OFF .
The LED indicator on the transmitter will light when the Function button is pressed .
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER
A. Setting the code on your new transmitter .
Remove battery cover .
Press firmly below arrow and slide battery cover off .
Slide code switches to your choice of UP and DOWN position .
Factory setting is all UP . Do not use this setting .
Use ball point pen or small screwdriver .
Slide firmly up or down .
B. Setting the code on your new Receiver unit .
1. Slide code switches to the same positions as set on your transmitter .
They must be set to same positions to work .
2. Replace battery cover on transmitter .
3. Make sure the code switches are on the left positions .
NOTICE :
The changes or modifications not expressly approved by the
party responsible for compliance could void user’s authority
to operate the equipment .
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result in
the device exceeding the RF exposure requirements and void user’s authority to operate the device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference
received, including interference that may cause
910805

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Language                        : zh-TW
Title                           : 貼於產品本體之FCC標籤圖解範例
Author                          : ETC
Creator                         : Writer
Producer                        : OpenOffice 4.1.1
Create Date                     : 2017:03:29 08:11:35+08:00

EXIF Metadata provided by EXIF.tools