Rhine Electronics Co 7235T Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3711392
Application ID	ROtcii7FB1DcnjU4h8DWBA==
Document Description	User_Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	57.44kB (718044 bits)
Date Submitted	2018-01-11 00:00:00
Date Available	2018-01-11 00:00:00
Creation Date	2017-11-02 09:15:58
Producing Software	OpenOffice 4.1.1
Document Lastmod	2018-01-11 09:58:14
Document Title	Users Manual
Document Creator	Writer
Document Author:	ETC

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
1. This unit operates on a 3 volts battery (not included).
To prevent possible damage if the battery should leak , be sure to remove
the battery when the unit is not use .
2.
Store the controller away from excess heat or humidity .
3.
This remote control unit is required with 24bit code combinations. To prevent
possible interference from or to other remote units such as garage door
openers, car alarm or security system .
4. Operation buttons on the panel of transmitter .
FAN SPEED button –
fan speed (HIGH, MED, LOW)
FAN OFF button FAN OFF
LED display
REV button – Fan reverse
Warm weather/Cool weather
LIGHT button Light ON/OFF or Dimmer
FAN TIMING button2 hour/ 4 hour / 8 hour
LED display
FAN SPEED button –
fan speed (HIGH, MED, LOW,OFF)
REV button – Fan reverse
Warm weather/Cool weather
LIGHT button Light ON/OFF or Dimmer
FAN TIMING button2 hour/ 4 hour / 8 hour
Light set Switch –
For set light dimmer type
or light ON/OFF type control .
5. Start the fan
Press the FAN speed button .
6. Turn off the fan :
Press the OFF button .
7. Light control :
Turn the light on or off by only touching the LIGHT CONTROL button .
Keep pressing the button in excess of 0.7 second it becomes a dimmer ,
the light varies cyclically in 0.8 second .
8. Timing set :
2H : 2 hours later, the fan is off
4H : 4 hours later, the fan is off
8H : 8 hours later, the fan is off
GENERAL INFORMATION :
This REMOTE controller is designed to separately control your
ceiling fan speed and light brightness . The Light
ON/OFF button will control the light brightness ON/OFF .
The LED indicator on the transmitter will light when the Function button is pressed .
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED
CONTROLLER
1. Setting the code on your new transmitter .
Within 60 seconds of turning the AC power on, press and hole the FAN ON/OFF
button for 5 seconds. The receiver will then lock in the chosen frequency.
If your fan has a light it it will blink twice, for fans without lights check operation using the
transmitter
NOTICE :
The changes or modifications not expressly approved by the
party responsible for compliance could void user’s authority
to operate the equipment .
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void user’s authority to
operate the device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may cause
FCC INFORMATION
The Federal Communication Commission Radio Frequency Interference
Statement includes the following paragraph:
The equipment has been tested and found to comply with the limits for a
Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communication.
However, there is no grantee that interference will not occur in a particular
installation. If this equipment dose cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on , the user is encouraged to try to correct the interference by one or
more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
1060718

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : ETC
Create Date                     : 2017:11:02 09:15:58+08:00
Modify Date                     : 2018:01:11 09:58:14+08:00
Language                        : zh-TW
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : ETC
Title                           : 貼於產品本體之FCC標籤圖解範例
Creator Tool                    : Writer
Metadata Date                   : 2018:01:11 09:58:14+08:00
Producer                        : OpenOffice 4.1.1
Document ID                     : uuid:625047b7-ed98-41ad-ac50-d2833608551a
Instance ID                     : uuid:f0257043-104f-4120-96e5-6274eb7e4ec6
Page Count                      : 4

EXIF Metadata provided by EXIF.tools