Rhine Electronics Co 8BTDTS-3S Remote Control Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	218978
Application ID	1P6FaHTlYD7MgCEux6NvKg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.55kB (56825 bits)
Date Submitted	2002-01-03 00:00:00
Date Available	2002-01-03 00:00:00
Creation Date	2001-12-31 11:56:50
Producing Software	Acrobat 5.0 Scan Plug-in for Windows
Document Lastmod	2001-12-31 11:57:23
Document Title	User Manual
Document Creator	Acrobat 5.0 Scan Plug-in for Windows

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS (DTS-3S)
l Wireless Keyless Entry System (Optional Accessory)
Wireless Keypad Installation
1. Slide oft both keypad and battery covers to fasten with 2 pan head screws.
2. Slide keypad cover onto Keypad.
3. Install a 9 volt battery and slide battery cover onto Keypad.
NOTE 1 Mount Keypad out of child‘s reach (at least 5 feet above floor).
Programming Wireless Keypad
1. Press and hold the “learn “ button (on the right side of the panel ) until
the green indicator light flashes (about 5 seconds )to erase old code.
2. Press and release the “learn" button (on the right side of the
panel ).
3. When the green indicator light is illuminated, press 4 desirde
digits and ENTER to code Keypad.
NOTE 2 When programming wireless keypad, the distance shall be at least 24
inches from the antenna of opener.
4. Enter the code to signal the system to open, close, stop or move the door
In the opposite direction.
You may set up this feature as follows:
1. Press and release the "learn" button (on the right side of
the panel).
2. When the green indicator light is illuminated, press and
hold the selected remote control push button
3. After the green indicator light flashed three times,
release
the button.
4.This stores open/stop/close function for the selected
button for the first opener in memory.
5,Repeat the same steps above on the second and third
openers.
Erase All Remote Control Codes
1. Press and hold the "learn" button (on the right side of the panel)
until the green indicator light flashes (about 5 seconds).
2. All transmitter codes are now erased.
Then follow the steps above to re-program each remote control.
NoticezThe changes or modifications not expressly approved by the party responsible
For compliance could void the user‘s authority to operate the equipment.
Note: This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions. (1) This device may no cause harmful
interference and (2) This device must accept any interference received,
including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2001:12:31 11:57:23+08:00
Create Date                     : 2001:12:31 11:56:50+08:00
Creator                         : Acrobat 5.0 Scan Plug-in for Windows
Page Count                      : 2
Mod Date                        : 2001:12:31 11:57:23+08:00
Creation Date                   : 2001:12:31 11:56:50+08:00
Producer                        : Acrobat 5.0 Scan Plug-in for Windows
Metadata Date                   : 2001:12:31 11:57:23+08:00

EXIF Metadata provided by EXIF.tools