Rhine Electronics Co 8BTG700TXP Remote Control Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	218927
Application ID	Tu5Tex7EuczLN2nSQfbq6Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.93kB (61610 bits)
Date Submitted	2002-01-03 00:00:00
Date Available	2002-01-03 00:00:00
Creation Date	2001-12-31 13:28:57
Producing Software	Acrobat 5.0 Scan Plug-in for Windows
Document Lastmod	2001-12-31 13:30:10
Document Title	User Manual
Document Creator	Acrobat 5.0 Scan Plug-in for Windows

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS (G700TXP)
Remote Control Programming
1.Disconnect the visor clip,then loosen the screw to lift the back case
of transmitter.
2.Choose the different function (3 Cor / 3 Oh) by inserting
the Mini Jumper into the left or the right of Pin Header.
Proper disposal of battery is required. Refer to your local codes for
disposal requirement.
30pr: Open/StopIClose Operation
(The Mini Jumper on the left side of Pin Header)
The remote control can be programmed to operate one door using all 3
buttons: the up button will only open the door. the middle button will stop
the door‘s movement, and the third button will only close it. 7 V
You may set up this feature as follows:
1. Press and release the "learn" button (on the right side of
the anel . ‘
2. When the green indicator light is illuminated, press and .
hold any one of the three buttons on transmitter. '
3, After the green indicator light flashes three times, release
the button.
4. This separately stores open/stop/close function for the
three buttons in memory.
30h: Channel Remote Control
(The Mini Jumper on the right side of Pin Header)
Permit to control 3 separate openers. Each button can operate one
particular door individually.
You may set up this feature as follows:
1. Press and release the "learn" button (on the right side of
the panel).
2. When the green indicator light is illuminated, press and
hold the selected remote control push button.
3. After the green indicator light flashed three times,
release
the button.
5. This stores open/stop/close function for the selected
button for the first opener in memory.
6. Repeat the same steps above on the second and third
openers.
Green hidiwor Light
Remote Comm]
Learn Button
Erase All Remote Control Codes
1. Press and hold the "learn" button (on the right side of the panel)
until the green indicator light flashes (about 5 seconds).
2. All transmitter codes are now erased.
Then follow the steps above to re-program each remote control.
NoticezThe changes or modifications not expressly approved by the party responsible
For compliance could void the user‘s authority to operate the equipment.
Note: This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions. (1) This device may no cause harmful
interference and (2) This device must accept any interference received,
including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2001:12:31 13:30:10+08:00
Create Date                     : 2001:12:31 13:28:57+08:00
Creator                         : Acrobat 5.0 Scan Plug-in for Windows
Page Count                      : 2
Mod Date                        : 2001:12:31 13:30:10+08:00
Creation Date                   : 2001:12:31 13:28:57+08:00
Producer                        : Acrobat 5.0 Scan Plug-in for Windows
Metadata Date                   : 2001:12:31 13:30:10+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools