Rhine Electronics Co 9051T Transmitter of Remote Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	890668
Application ID	/K7inGAimGSYXZTnLgsEsw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.12kB (39017 bits)
Date Submitted	2008-01-17 00:00:00
Date Available	2008-01-17 00:00:00
Creation Date	2008-01-11 15:15:39
Producing Software	Acrobat PDFWriter 5.0Windows NT ª©
Document Lastmod	0000-00-00 00:00:00
Document Title	Users Manual
Document Creator	使用手冊 - Microsoft Word
Document Author:	user

Page 1/1
INSTRUCTIONS FOR OPERATION
SETTING THE OPERATING CONTROLS
1、 This device which one of black lines series with AC 120V power supply. Now, we
take 60Hz power supply to afford power supply of transmitter when it trough
rectify. So, there is no troubles with change batteries forever.
2、 Store the controller away from excess heat or humidity.
3、 This remote control unit is required with 16 code combinations. To prevent
possible interference from or to other remote units such as garage door openers, car
alarm or security system. If you find that your fan and light kit go on and off
without using your control, simply change the combination code in your
transmitter and receiver.
4、 Operation buttons on the panel of transmitter.
HI
key- For fan High speed.
MED
key-For fan Medium speed.
LOW
key-For fan low speed.
Fan off
key-For fan speed Off.
LIGHT
key-For light brightness and ON/OFF control.
REV
key-For fan speed Reverse.
5、 Start the fan :
Press the selected speed button to run the fan at the desired.
6、 Turn off the fan:
Press the FAN OFF button.
7、 Light control:
Turn the light on or off by only touching the LIGHT
button.
Keep pressing the button in excess of 0.7 second it becomes a dimmer, the light
varies cyclically in 0.8 second.
One of the important feature of this control is AUTO-RESUME. After power on, it
allows the light return to where it was off.
Page 2/2
GENERAL INFORMATION：
This REMOTE controller is designed to separately control your ceiling fan speed and
light brightness. There are five buttons (Hi,Med,Low,FanOff,Rev) to control the
fan speed and off. The Light Dimmer button will control the light brightness
dimmer and off. The ON/OFF switch will turn on and turn off the unit’s power
supply.
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED
CONTROLLER
A. Setting the code on your new transmitter.
1.
Slide code switches to your choice of UP and Down position.
Factory setting is all UP. Do not use this setting.
Use ball point pen or small screwdriver.
slide firmly up or down.
B. Setting the code on your new Receiver unit.
1.
2.
Slide code switches to the same positions as set on your transmitter.
They must be set to same positions to work.
Make sure the code switches are on the right positions.
NOTICE：
The changes or modifications not expressly approved by the party responsible
for compliance could void user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any change to the antenna or
the device could result in the device exceeding the RF exposure requirements and
void user’s authority to operate the device.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Creator                         : 使用手冊 - Microsoft Word
Create Date                     : 2008:01:11 15:15:39
Title                           : 使用手冊.doc
Author                          : user
Producer                        : Acrobat PDFWriter 5.0Windows NT ª©

EXIF Metadata provided by EXIF.tools