Rhine Electronics Co GTXE1 Transmitter of Remote Control User Manual GTXE1 rev

Download:
Mirror Download [FCC.gov]
Document ID	993207
Application ID	E7WvRmA8CRy6i1gSmDa7+A==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.35kB (29324 bits)
Date Submitted	2008-08-31 00:00:00
Date Available	2008-08-31 00:00:00
Creation Date	2008-08-01 09:46:46
Producing Software	Acrobat PDFWriter 5.0Windows NT ª©
Document Lastmod	0000-00-00 00:00:00
Document Title	GTXE1使用手冊_rev.doc
Document Creator	GTXE1使用手冊_rev - Microsoft Word
Document Author:	Administrator

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
Model:OCDTR-3 , GITR-3
Remote Control Programming For Grage door opener
1.Loosen the screw to lift the back case of transmitter.
2.Choose the different function (3 Opr / 3 Ch) by inserting
the Mini Jumper into the left or the right of Pin Header.
Proper disposal of battery is required. Refer to your local
codes for disposal requirement.
3Opr: Open/Stop/Close Operation
(The Mini Jumper on the left side of Pin Header)
The remote control can be programmed to operate one door
using all 3 buttons: the up button will only open the door, the
middle button will stop the door's movement, and the third
button will only close it.
You may set up this feature as follows:
1. Press and release the "learn" button (on the right side of
the panel).
2. When the green indicator light is illuminated, press and
hold any one of the three buttons on transmitter.
3. After the green indicator light flashes three times, release
the button.
4. This separately stores open/stop/close function for the
three buttons in memory.
mini jumper
3Ch: Channel Remote Control
(The Mini Jumper on the right side of Pin Header)
3 Ch ←
→ 3 Opr
Permit to control 3 separate openers. Each button can operate
one particular door individually.
You may set up this feature as follows:
1. Press and release the "learn" button (on the right side of
the panel).
2. When the green indicator light is illuminated, press and
hold the selected remote control push button.
3. After the green indicator light flashed three times, release
the button.
5. This stores open/stop/close function for the selected
button for the first opener in memory.
6. Repeat the same steps above on the second and
third
openers.
1/1
Erase All Remote Control Codes
1. Press and hold the "learn" button (on the right side of the
panel) until the green indicator light flashes (about 5
seconds).
2. All transmitter codes are now erased.
Then follow the steps above to re-program each remote control.
Notice : The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
2/2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Creator                         : GTXE1使用手冊_rev - Microsoft Word
Create Date                     : 2008:08:01 09:46:46
Title                           : GTXE1使用手冊_rev.doc
Author                          : Administrator
Producer                        : Acrobat PDFWriter 5.0Windows NT ª©

EXIF Metadata provided by EXIF.tools