Rhine Electronics Co UC8011T Remote Control Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	305474
Application ID	maHmiv3PHLgV0niDjLbLSQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	31.04kB (388057 bits)
Date Submitted	2003-02-26 00:00:00
Date Available	2003-02-26 00:00:00
Creation Date	2003-02-12 13:02:39
Producing Software	Acrobat 5.0 Image Conversion Plug-in for Windows
Document Lastmod	2003-02-12 13:03:28
Document Title	User Manual
Document Creator	Acrobat 5.0 Image Conversion Plug-in for Windows

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
1.This unit operates on a 6 vols battery (not included).
To prevent possible damage if the battery should leak , be sure to remove
the battery when the unit is not use .
2. Store the controller away from excess heat or humidity .
3. This remote control unit is requipped with 16 code combinations. To prevent
possible interference from or to other remote units such as garage door
openers> car alarm or security system . If you find that your fan and light
kit go on and offwithout using your control , simply change the combination
code in your transmitter and receiver .
4,0peration buttons on the panel of transmitter .
HIGH key — For fan High speed .
MED key — For fan Medium speed .
LOW key — For fan Low speed .
OFF key — For fan speed off.
REV key — For fan speed Reverse .
LIGHT CONTROL key — For light brightness and ON/OFF control ,
5.Sta11 the fan :
Press the selected speed button to 11m the fan at the desired .
6.Tuin off the fan :
Press the OFF button .
7.Light control :
Turn the light on or off by only touching the LIGHT CONTROL button .
Keep pressing the button in excess of 0.7 second it becomes a dimmer ,
the light varies cyclically in 0.8 second .
One ofthe important feature ofthis control is AUTO-RESUME , Afier power
on , it allows the light return to where it was off .
GENERAL INFORMATION :
This REMOTE controller is designed to separetly control your
ceiling fan speed and light brightness . The Light
ON/OFF button will control the light brightness ON/OFF .
The red indicator on the transmitter will light when the button is pressed .
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER
A. Setting the code on your new transmitter .
1, Remove battery cover .
Press firmly below arrow and slide battery cover off ,
2. Slide code switches to your choice of UP and DOWN position .
Factory setting is all UP . Do not use this setting .
Use ball point pen or small screwdriver .
Slide firmly up or down .
B. Setting the code on your new Receiver unit .
1. Slide code switches to the same positions as set on your transmitter .
They must. be set to same positions to work .
2. Replace battery cover on transmitter .
3. Make sure the code switches are on the lefi positions .
NOTICE:
The changes or modifications not expressly appproved by the
party responsible for compliance could void user’s authority
to operate the equipment.
This device complies with part 15 of the FCC Mm. Operation is subject to the following
two conditions. (1) This device may not cause harmful interference and (2) This device
must accept any interference received, including interference thal may muse undesired
operation.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted Any
change to the antenna or the device could result in the device exceeding
the RF exposure requirements and void user’ s authority to operate the
device.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2003:02:12 13:03:28+08:00
Create Date                     : 2003:02:12 13:02:39+08:00
Creator                         : Acrobat 5.0 Image Conversion Plug-in for Windows
Page Count                      : 2
Mod Date                        : 2003:02:12 13:03:28+08:00
Creation Date                   : 2003:02:12 13:02:39+08:00
Producer                        : Acrobat 5.0 Image Conversion Plug-in for Windows
Metadata Date                   : 2003:02:12 13:03:28+08:00

EXIF Metadata provided by EXIF.tools