Richen S5 Bluetooth Speaker User Manual TW1604007
Richen Industrial Co.,Ltd Bluetooth Speaker TW1604007
Richen >
User Manual
Waterproof Bluetooth Speaker
Model Number : S5
Charging The Bluetooth Speaker
1. Open the rubber seal cover on the side. Charging time 3 hours.
2. Connect the Bluetooth Speaker’s Micro USB socket with the Computer’s USB port through
USB cable.
3. The Charging LED will turn ON in red light; the rechargeable battery is in charging.
4. The Charging LED red light will turn OFF when the rechargeable battery is fully charged.
5. Disconnect the USB cable, and close the Rubber Seal Cover when it is done.
Bluetooth Speaker Pairing / Reconnecting
1. Press the button for 3 seconds, Mode LED will blink alternately in blue and red; the
device is turned ON and goes into searching / paring / reconnect mode for pair.
2. Now, turn ON the Bluetooth function on your mobile phone.
3. Search for “S5” and select it to pair.
The Bluetooth Speaker will be reconnecting automatically if your mobile phone has been
paired. (Depend on the of mobile phone’s type and configuration, manual reconnection
may require on some devices)
4. If pairing is successful, Mode LED light will switch to slow blink in blue (once per 3
seconds).
5. Press the button for 3 seconds to turn OFF the Bluetooth Speaker.
Note: If can’t search Speaker, means the last mobile phone is reconnecting automatically
successfully. Should press the button and button for 3 seconds to delete last mobile
and pair new mobile.
Bluetooth Speaker Control Function
1. In playing music, press button to pause music, press it once again to play.
2. Press the button to increases the volume level.
3. Press the button to decreases the volume level.
4. Press and hold the button to play next music file.
5. Press and hold the button to play previous music file.
Hand Free Function & Redial For Last Call function
1. Press button to pick up the call and the playing music will pause automatically.
2. Press button for 2 seconds to reject the call.
3. Press button again to hand up the call when finished. The paused music will start to
play automatically.
4. To redial for last called number by the Bluetooth Speaker, even it is in music playing mode.
Press twice the button to enter into redial function.
Tip: speak to the MIC hole direct with distance in 30 cm to get the best speakerphone
performance when necessary.
AUX IN Function
1. In power ON mode, connect the Bluetooth Speaker’s AUX IN Jack with an external
device’s “Earphone / AUX / LINE” Output through the Line-in cable.
2. The Bluetooth Speaker will switch to “AUX In” mode automatically from Bluetooth mode,
and the Mode LED will slow blink in blue. All speaker button will be invalid under AUX-IN
function.
3. Disconnect the Audio cable when it is done. Add one more notice: Line in the audio cable
while the Bluetooth connected, if the music is stopped and no sound, please pull out both
ends of the audio cable and then plug in again, if there is still no sound that audio cable
needs to be replaced.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
‐‐Reorient or relocate the receiving antenna.
‐‐Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
‐‐Consult the dealer or an experienced radio/TV technician for help.