Users Manual
COMPACT DISC REWRITABLE DRIVE MP7210A SPECIFICATIONS (Preliminary) RICOH Company, Ltd. May. 16, 2000 DRC – 60x - 2xx NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device , pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates , uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions , may cause harmful interference to radio communication. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception , which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures : ---Reorient or relocate the receiving antenna. ---Increase the separation between the equipment and receiver. ---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ---Consult the dealer or an experienced radio / TV technician for help. FCC WARNING Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. a) Pay careful attention not to let the invisible laser beam emitted from the optical pickup enter into your eyes. b) When you find a troubled state of the component in the optical pickup containing the laser diode , change to the specified new optical pickup. Do not open the optical pickup housings. Akustischer Geräuschpegel Dieser Drucker überschreitet einen Geräuschpegel von 70 dB (A) während dem Betrieb nicht. Declaration of Conformity “The Product complies with the requirements of the EMC Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC.” Revision History No. Revised Data Revision Contents Description May. 16, 2000 Preliminary Page CONTENTS I. OUTLINE -----------------------------------------------------------------------------------------------------1. 2. Overview ........................................................................................................... I - 1 Features............................................................................................................ I - 1 II. CONSTRUCTION AND INSTALLATION ---------------------------------------------------------1. Basic Construction and Connectors ................................................................ II - 1 III. SPECIFICATIONS ---------------------------------------------------------------------------------------1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Functionality....................................................................................................III - 1 Basic Specification .........................................................................................III - 2 Audio Specification .........................................................................................III - 3 Performance Specification .............................................................................III - 3 Condition for use and Safety standard...........................................................III - 3 Reliability and Usable Life ..............................................................................III - 6 Safety Standards ............................................................................................III - 6 Appearance ....................................................................................................III - 7 Storage Conditions .........................................................................................III - 8 Emergency Eject............................................................................................III - 10 Disc.................................................................................................................III - 11 Packet Command...........................................................................................III - 12 FIGURE II - 1. II - 2. II - 3. Front ........................................................................................................II - 1 Back.........................................................................................................II - 1 Device Configuration Jumper..................................................................II - 2 III - 1. III - 2. III - 3. III - 4. Installation Conditions .............................................................................III - 5 CD-R/RW Drive Dimension.....................................................................III - 7 Packing Arrangement..............................................................................III - 9 Emergency Eject.....................................................................................III - 10 TABLE III - 1. Packet Command....................................................................................II - 1 I. OUTLINE 1. Overview The Multimedia Printer Series Drive (the CD-R/RW Drive) can do much more than read and write the usual CD-R discs. When you load it with a rewritable CD-RW disc, you can record, read, and edit any kind of data, because these discs allow you to rewrite information that has already been recorded. 2. Features 1) Running OPC*1 gives a flatter writing signal that improves reliability. 2) An improved anti-heat design means that no cooling fan is needed. 3) Easy-to-use tray model. 4) Uses the world standard ATAPI interface. 5) Can read not only CD-R and CD-RW discs, but also video CDs, music CDs, and photo CDs. 6) Can read data at 32x speed and write data at 12x speed on CD-R, 10x speed on CD-RW discs. 7) The recorded CD-RW media can be played in a DVD player or multimedia CDROM player, maintaining future compatibility. 8) Supports packet write for easy writing to CD-R and CD-RW discs. *1 Continuously monitors the signal level during recording and adjusts the laser power to compensate when the disc is dirty, insuring a flat signal. II. CONSTRUCTION AND INSTALLATION 1. Basic construction and Connectors The Connectors are located as shown below. The function of each parts are also described below. Volume control Headphone Jack Emergency Eject hole Disc Tray Busy indicator Eject Button Fig. II - 1 Front Digital Audio Output (Not used) Audio Output Connector Device Configuration Jumper E-IDE Connector Fig. II - 2 Back Power Connector 1.1. Disc Tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the CD will be loaded. ! - Don’t use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 1.2. Eject Button This is the button used to eject or bring in the disc tray. 1.3. Busy indicator When the disc tray or disc is being accessed, the light shines or flashes orange. Even when a disc is loaded or a disc is not being accessed, the light go out. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 1.4. Headphone Jack This jack is for connecting headphones or mini-speakers. 1.5. Volume control This is used to adjust the output volume of the headphone jack. It can’t be used to adjust the output volume for the audio output connectors on the rear panel. 1.6. Emergency Eject hole When the drive can not eject the Disc Tray because of power failure, pushing the Emergency Eject hole of the Front Panel by the thin pole make drive be able to eject the Disc Tray. ! - This function is only for emergency case. Do not use this function in usual case to prevent from mechanical damage. 1.7. Power Connector Used to connect to the host computer’s power supply (DC 5V / 12V) ! - Be careful not to reverse the poser connector when attaching it. A reversed connection may cause damage to the equipment (not covered by the warranty). 1.8. E-IDE Connector Use a 40 pin double-end flat E-IDE cable to connect to the E-IDE interface. ! - Connecting or disconnecting connectors while power is on may result in a short circuit, causing damage to the equipment. When connecting or disconnecting connectors, make sure to turn off the power beforehand. 1.9. Audio Output Connector Used to connect to the sound card. (Analog signal.) 1.10. Digital Audio Output (Not used) Used to connect to the sound card. (Digital signal.) It is not used with this drive. 1.11.Device Configuration Jumper Used when selecting the Device Configuration of E-IDE. Don’t use jumpers to change anything besides the Device Configuration, but keep the drive as initially set(“Master” position). Configuration changes become valid after power is turned off, then on again. ! - Installing jumper pins besides the ones for Device Configuration settings may be the cause of damage or abnormal drive operation. Fig. II - 3 Device Configuration Jumper The Device Configuration Jumper will be set to Master as factory setting.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Creator : .橡.Microsoft Word Create Date : 2000:05:19 18:50:29 Title : .橡.User_Manual.PDF Author : .橡.iida Producer : Acrobat PDFWriter 4.0 Windows Modify Date : 2000:05:19 18:51:58+09:00 Page Count : 10EXIF Metadata provided by EXIF.tools