Ricoh 9120A CD-R/RW & DVD-ROM User Manual SpecPre9120A

Ricoh Company Ltd CD-R/RW & DVD-ROM SpecPre9120A

User Manual

MP9120A SPECIFICATIONS(May 2, 2000)I - 1 (Preliminary)COMPACT DISC Recordable/ReWritable&DVD-ROM DRIVEMP9120ASPECIFICATIONS (Preliminary)RICOH Company, Ltd.May 2, 2000DRC-603-807
MP9120A SPECIFICATIONS(May 2, 2000)I - 2 (Preliminary)NOTICEThis equipment has been tested and found to comply with the limits for a Class B digitaldevice , pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates , uses and can radiate radio frequency energy and , if not installed andused in accordance with the instructions , may cause harmful interference to radiocommunication.However , there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception , which canbe determined by turning the equipment off and on , the user is encouraged to try to correctthe interference by one or more of the following measures :---Reorient or relocate the receiving antenna.---Increase the separation between the equipment and receiver.---Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.---Consult the dealer or an experienced radio / TV technician for help.FCC WARNINGChanges or modification not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.CAUTIONUse of controls or adjustments or performance of procedures other than those specifiedherein may result in hazardous radiation exposure.a) Pay careful attention not to let the invisible laser beam emitted from the optical pickup enterinto your eyes.b) When you find a troubled state of the component in the optical pickup containing the laserdiode , change to the specified new optical pickup. Do not open the optical pickup housings.
MP9120A SPECIFICATIONS(May 2, 2000)I - 3 (Preliminary)Akustischer GeräuschpegelDieser Drucker überschreitet einen Geräuschpegel von 70 dB (A) während dem Betriebnicht.Declaration of Conformity“The Product complies with the requirements of the EMC Directive 89/336/EECand the Low Voltage Directive 73/23/EEC.”
MP9120A SPECIFICATIONS(May 2, 2000)I - 4 (Preliminary)Revision HistoryNo. Revised Data Revision Contents Description Page1May 2, 2000 Preliminary
MP9120A SPECIFICATIONS(May 2, 2000)I - 5 (Preliminary)CONTENTSI. OUTLINE-------------------------------------------------------------------------------------------------------1. Overview...........................................................................................................I - 12. Features............................................................................................................I - 1II. CONSTRUCTION AND INSTALLATION----------------------------------------------------------1. Basic Construction...........................................................................................II - 12. Connector.........................................................................................................II - 2III. SPECIFICATIONS ----------------------------------------------------------------------------------------1. Functionality....................................................................................................III - 12. Basic Specification.........................................................................................III - 23. Audio Specification .........................................................................................III - 34. Performance Specification.............................................................................III - 35. Condition for use and Safety standard...........................................................III - 36. Reliability and Usable Life...............................................................................III - 67. Safety Standards ............................................................................................III - 68. Appearance.....................................................................................................III - 79. Storage Conditions .........................................................................................III - 810. Emergency Eject............................................................................................III - 1011. Disc.................................................................................................................III - 1112. Packet Command...........................................................................................III - 12
MP9120A SPECIFICATIONS(May 2, 2000)I - 6 (Preliminary)FIGUREII - 1. Drive configuration...................................................................................II - 1II - 2.Front ........................................................................................................II - 2II - 3.Back.........................................................................................................II - 2II - 4.Device Configration Jumper....................................................................II - 4III - 1.Installation Conditioins.............................................................................III - 5III - 2. Drive Dimension......................................................................................III - 7III - 3. Packing Arrangement..............................................................................III - 9III - 4. Emergency Eject.....................................................................................III - 10TABLEIII - 1. Packet Command ...................................................................................III - 12
MP9120A SPECIFICATIONS(May 2, 2000)I - 7 (Preliminary)I. OUTLINE1. OverviewThe CD-Recordable/CD-ReWritable/DVD-ROM drive, the MP9120A, can write and readvarious data in a CD-R disc and also a CD-RW disc which can be rewritten the datarecorded once. It is not concern about failure in writing that is one of concern over theusual CD-R, because it is possible to try to write again.The MP9120A drive has 12X CD-R recording, 10X CD-RW rewriting and a 32X(maximum speed) CD-reader.In addition, the MP9120A drive has a 8X DVD-ROM-reader.2. Features1) Examining laser power by APC (Auto Power Control) on real time when reading,realizes high reliability of writing without fluctuating laser power to fluctuation ofthe temperature. 2) An improved anti-heat design means that no cooling fan is needed. 3) Easy-to-use tray model. 4) Uses the world standard E-IDE (ATAPI) interface. 5) Can read data at 32X speed (4.8MB/sec. Data transfer rate) and write data at12X speed (1.8MB/sec. Data transfer fate).* CD-RW disc is 10X speed write. DVD-ROM disc is 8X speed read. 6) Supports packet write for easy writing to CD-R and CD-RW discs.
MP9120A SPECIFICATIONS(May 2, 2000)I - 8 (Preliminary)II. CONSTRUCTION AND INSTALLATION1. Basic ConstructionThe CD Recordable/Rewritable/DVD-ROM Drive: MP9120A consists of following parts.The CD Recordable/Rewritable/DVD-ROM Drive’s configuration and Connector areshown below; MAIN PCBLOADING UNITTURN TABLEPICKUPUNIT FACE LOAD/EJECTBUTTONHEADPHONEJACKMOTOR PCB LEDDOORVOLUME VIBRATIONISOLATORFig. II - 1 Drive configuration
MP9120A SPECIFICATIONS(May 2, 2000)I - 9 (Preliminary)2. ConnectorThe Connectors are located as shown below. The function of each parts are alsodescribed below.Fig. II - 2 FrontFig. II - 3 BackVolume controlEject ButtonHeadphone Jack Disc Tray Busy indicatorEmergency Eject holeDigital Audio Output Connector Device Configration JumperAudio Output Connector E-IDE Connector Power Connector
MP9120A SPECIFICATIONS(May 2, 2000)I - 10  (Preliminary)2.1. Disc TrayThis is the tray for the disc. Place the disc on the ejected disc tray, then lightlypush the tray (or push the eject button) and the CD will be loaded. ! - Don’t use force to pull out or push in the disc tray. This might cause damageto the loading section of the drive.2.2. Eject ButtonThis is the button used to eject or bring in the disc tray.2.3. Busy indicatorWhen the disc tray or disc is being accessed, the light shines or flashes orange.Even when a disc is loaded or a disc is not being accessed, the light go out. When aillegal disc is loaded or some hardware trouble occurs, the indicator blinks.2.4. Headphone JackThis jack is for connecting headphones or mini-speakers.2.5. Volume controlThis is used to adjust the output volume of the headphone jack. It can’t be used toadjust the output volume for the audio output connectors on the rear panel.2.6. Emergency Eject holeWhen the drive can not eject the Disc Tray because of power failure, pushing theEmergency Eject hole of the Front Panel by the thin pole make drive be able toeject the Disc Tray. !- This function is only for emergency case. Do not use thes function in usualcase to prevent from mechanical damage.2.7. Power ConnectorUsed to connect to the host computer’s power supply (DC 5V / 12V) ! - Be careful not to reverse the poser connector when attaching it. A reversedconnection may cause damage to the equipment (not covered by thewarranty).2.8. E-IDE ConnectorUse a 40 pin double-end flat E-IDE cable to connect to the E-IDE interface. ! - Connecting or disconnecting connectors while power is on may result in ashort circuit, causing damage to the equipment. When connecting ordisconnecting connectors, make sure to turn off the power beforehand.2.9. Audio Output ConnectorUsed to connect to the sound card. (Analog signal.)2.10. Digital Audio OutputUsed to connect to the sound card. (Digtal signal.)2.11.Device Configration JumperUsed when selecting the Device Configration of E-IDE. Don’t use jumpers to changeanything besides the Device Configration, but keep the drive as initially set(“Master”position). Configration changes become valid after power is turned off, then on again. ! - Installing jumper pins besides the ones for Device Configration settings maybe the cause of damage or abnormal drive operation.
MP9120A SPECIFICATIONS(May 2, 2000)I - 11  (Preliminary)Fig. II - 4 Device Configration JumperThe Device Configration Jumper will be set to Master as factory setting.
MP9120A SPECIFICATIONS(May 2, 2000)I - 12  (Preliminary)RICOH COMPANY, LTD.3-2-3, Shin-Yokohama, Kohoku-kuYokohama 222-8530 JapanTEL 045-477-1660
MP9120A SPECIFICATIONS(May 2, 2000)I - 13  (Preliminary)FAX 045-477-1807

Navigation menu