Ricoh Projector Pj X5260 Users Manual
PJ X5260 to the manual d3391c08-3a79-45de-92d6-6ee537f2a871
2015-01-23
: Ricoh Ricoh-Ricoh-Projector-Pj-X5260-Users-Manual-274962 ricoh-ricoh-projector-pj-x5260-users-manual-274962 ricoh pdf
Open the PDF directly: View PDF 
.
Page Count: 60
User’s Manual
For safe and correct use, be sure to read the “Usage Notice” before using the projector.
1
English
Table of Contents
Table of Contents ............................1
Usage Notice ....................................2
Precautions .........................................2
Safety Labels of This Machine ............6
Regulation & Safety Notices ...............7
Other Information ..............................12
Introduction ....................................13
Product Features ..............................13
Package Overview ............................14
Product Overview .............................15
Connection Ports .................................. 16
Control Panel........................................ 17
Remote Control ....................................18
Remote Control Battery Installation...... 20
Remote Control Operating Range ........ 20
Basic Operations ...........................21
Connecting the Projector ..................21
Connect to Computer/Notebook ........... 21
Connect to AV Equipment .................... 22
Powering On/Off the Projector ..........23
Powering On the Projector ...................23
Powering Off the Projector ...................24
Warning Indicator .................................25
Adjusting the Projected Image ..........26
Adjusting the Position of Projector
Image ................................................... 26
Adjusting the Projector Zoom and
Focus.................................................... 27
Adjusting Projection Image Size........... 27
User Settings .................................29
Using the On Screen Display (OSD) 29
How to operate ..................................... 29
Image Adjustment ................................ 30
Image Adjustment| Position .................. 32
Display Settings.................................... 33
Default Settings 1 ................................. 36
Default Settings 2 ................................. 38
Default Settings 2 | 3D Projection ........ 41
Default Settings 2 | Network Setting ..... 42
Display Status ...................................... 43
Controls via Network.....................44
Troubleshooting ............................46
Replacing the lamp........................51
Cleaning the lter ..........................52
Appendices ....................................53
List of Compatible Signals ................53
Congurations of Terminals ..............55
Terminal: Computer in 1/2
(Mini D-sub 15 pin) ............................... 55
Terminal: PC Control (D-sub 9 pin) ...... 55
Specications ....................................56
Trademarks .......................................57
2
English
Usage Notice
Precautions
Follow all warnings, precautions and maintenance as recom-
mended in this user’s guide to maximize the life of your unit.
Warning-■This apparatus must be earthed.
Warning-■Do not look into the projector’s lens when the
lamp is on. The bright light may hurt your eyes.
Warning-■To reduce the risk of re or electric shock, do not
expose this projector to rain or moisture.
Warning-■Please do not open or disassemble the projector
as this may cause electric shock.
Warning-■When replacing the lamp, please allow unit to
cool down, and follow all replacement instruc-
tions.
Warning-■When the lamp reaches the end of its life, it will
burn out and may make a loud popping sound.
If this happens, the projector will not turn back
on until the lamp module has been replaced. To
replace the lamp, follow the procedures listed
under “Replacing the Lamp”.
Warning-■Do not remove the cabinet cover, or you may be
exposed to dangerous voltage. Refer servicing to
qualied service personnel only.
Warning-■This product should be operated only from the
type of power source which does not exceed the
voltage range specied on the rating label and
the power cord. If you are not sure of the type of
power supply to your home, consult your sales
representative or local power company.
Warning-■Do not use the polarized plug with an exten-
sion cord , receptacle, or other outlet unless the
blades can be inserted completely with three
wire grounding type to prevent blade exposure.
Failure to follow these instructions may result in
re or electric shock.
3
English
Usage Notice
Caution-■Never operate this unit on AC power during a
thunderstorm. If you see lightning or hear thun-
der, never touch the unit, cables and/or periph-
erals. An electric surge caused by the storm, may
result in an electrical shock or damage to the
unit.
Caution-■Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a re or electric shock. Never spill liquid of
any kind on the product.
Caution-■Do not place or keep the projector within the
reach of the children. It may fall or tip over, pos-
sibly causing serious injury.
Caution-■Do not stack other equipment on this product
and do not place this product on other equip-
ment. The top and bottom surface of this product
increase in temperature during normal use and
may damage the other unit.
Caution-■Do not use attachments not recommended by the
product manufacturer. Use of an incompatible
attachments could cause hazards or damage to
the product.
Caution-■Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult,
and serious damage to the product.
Caution-■Unplug this product from the wall outlet and
take the product to qualied service personnel if
you encounter any of the following conditions:
a) The power supply cord or plug is damaged.
b) Liquid has been spilled, or objects have fallen
into the product.
c) The product has been exposed to rain or water.
d) The product does not operate normally when
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions.
e) The product has been dropped or damaged in
any way. (If the cabinet should break, please
handle with care to avoid injury.)
4
English
Usage Notice
Caution-■This product incorporates glass components, in-
cluding a lens and a lamp. If these should break,
please handle with care to avoid injury and con-
tact your sales representative for repair service.
Avoid any broken pieces of glass since they may
cause injury. In the unlikely event that the lamp
ruptures, thoroughly clean the area around the
projector and discard any edible items placed in
that area since they may be contaminated.
Caution-■Do not place anything in front of the lens while
the projector is operating Things placed in front
of the lens may overheat and burn or start a re.
Caution-■Do not use lens cap when projector is powered
on.
Caution-■Unauthorized substitutions may result in re,
electric shock, or other hazards. (Only the re-
placement of the lamp should be made by users.)
Caution-■Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to verify that the product is in
proper operating condition.
Caution-■Do not leave thermal paper documents or easily
deformed items on top of the unit or near the air
exhaust for long periods of time.
Caution-■The heat from the unit could erase the informa-
tion on the thermal paper, or cause deformation
or warping.
Caution-■This projector will detect the life of the lamp
itself. Please be sure to change the lamp when it
shows warning messages.
Caution-■Do not use the product in a closed installation
location. Do not place the product in a box or in
any other closed installation location. Otherwise
it may overheat, which could result in a risk of
re.
5
English
Usage Notice
Do:
After unpacking this product, read the manual carefully, and
follow all the operating and other instructions.
Turn off the product before cleaning.
Use a soft cloth moistened with mild detergent to clean the
display housing.
Disconnect the power plug from AC outlet if the product is not
being used for a long period of time.
Do not:
Block the slots and openings on the unit provided for ventila-
tion.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
Extremely heat, cold or humidity.
In areas susceptible to excessive dust and dirt.
Near any appliance generating a strong magnetic field.
In direct sunlight.
Important:
Contents of this manual are subject to change without prior notice.
In no event will the company be liable for direct, indirect, special,
incidental, or consequential damages as a result of handing or
operating this product.
■
■
■
■
■
■
■
-
-
-
-
6
English
Usage Notice
Safety Labels of This Machine
1 Do not block the air intake or exhaust. Doing so could cause a re
due to internal overheating. Do not place your hands, face, or other
objects near the air exhaust, the lamp cover or the bottom of the
unit. Doing so could result in injury and/or damage the object.
2 Do not place anything in front of the lens while the projector is op-
erating. Things placed in front of the lens may overheat and burn or
start a re. If you want to temporarily stop the projected image, use
the AV mute on the remote control or the keypad.
3 Do not look into the lens while the lamp is on. The strong light from
the lamp may cause damage to your eyesight.
4 To replace the lamp, rst unplug the power cord then wait for more
than 1 hour. The lamp might be broken. Be careful of pieces of bro-
ken glass.
5 Do not remove any screws except the lamp cover screws. Do not
block or cover the vents.
1 2
3
4
5
7
English
Usage Notice
Regulation & Safety Notices
This appendix lists the general notices of your Projector.
Notice: Users in the United States of America
FCC notice
MODEL NAME: PJ X5260
TRADE NAME: PROJECTOR
MODEL NAME: PJ X5260
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, in-
cluding interference that may cause undesired operation.
This device has been tested and found to comply with the limits
for a Class B digital device pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
device generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be deter-
mined by turning the device off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
▀■ Reorient or relocate the receiving antenna.
▀■ Increase the separation between the device and receiv-
er.
▀■ Connect the device into an outlet on a circuit different
from that to which the receiver is connected.
▀■ Consult the dealer or an experienced radio/television
technician for help.
Warning: this product
contains a chemical
known to the state of
California to cause
cancer, birth defects
or other reproductive
harm.
8
English
Usage Notice
RESPONSIBLE PARTY: Ricoh Americas Corporation
5 Dedrick Place, West Caldwell, NJ 07006
Phone: 973-882-2000
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance
with FCC regulations.
Caution
Changes or modications not expressly approved
by the manufacturer could void the user’s authority,
which is granted by the Federal Communications
Commission, to operate this projector.
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY
AND MUST BE RECYCLED OR DISPOSED OF ACCORD-
ING TO LOCAL, STATE OR FEDERAL LAWS.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs cana-
diens
Cet appareil numerique de la classe B est conforme a la norme
NMB-003 du Canada.
Declaration of Conformity for EU countries
▀■ EMC Directive 2004/108/EC (including amendments)
▀■ Low Voltage Directive 2006/95/EC
9
English
Usage Notice
CE Marking Traceability Information (For EU Countries
Only)
Manufacturer:
Ricoh Co., Ltd.
3-6 Nakamagome 1-chome, Ohta-ku, Tokyo. 143-8555, Japan
Authorized representative:
Ricoh Europe PLC
20 Triton Street, London. NW1 3BF, United Kingdom
Overseas Afliates and Noise Emission Information
In accordance with TUV “GS Symbol” requirements, details of the EU ofce or
representative company are given below.
Overseas Afliates
Ricoh Europe PLC
20 Triton Street, London. NW1 3BF, United Kingdom
Noise Emission
Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO
7779
User Information on Electrical and Electronic Equipment
Users in the countries where this symbol shown in this section has been speci-
ed in national law on collection and treatment of E-waste.
Our Products contain high quality components and are designed to facilitate recycling.
Our products or product packaging are marked with the symbol below.
10
English
Usage Notice
This product contains substances which are harmful to humans and the environment.
The lamp contains mercury.
Please dispose of this product or used lamps in accordance with local regulations.
The symbol indicates that the product must not be treated as municipal waste. It must
be disposed of separately via the appropriate return and collection systems available. By
following these instructions you ensure that this product is treated correctly and help to
reduce potential impacts on the environment and human health, which could otherwise
result from inappropriate handling. Recycling of products helps to conserve natural re-
sources and protect the environment.
For more detailed information on collection and recycling systems for this product, please
contact the shop where you purchased it, your local dealer or sales/service representatives.
All Other Users
If you wish to discard this product, please contact your local authorities, the shop
where you bought this product, your local dealer or sales/service representatives.
For Turkey only
REMOTE CONTROL BATTERIES
Warning
Never throw batteries into a re.
Using the batteries improperly may cause them to explode or leak and may result in seri-
ous injury. If battery-leaking uid contacts skin, wash the uid off immediately with clean
water and consult a doctor. If the uid spills on an instrument, avoid contact and wipe it
off using tissue paper. Then dispose of the used tissue paper as ammable garbage after
moistening the tissue with water.
Notes
Be sure to use AAA (R03) size batteries.
Dispose of batteries in a designated disposal area.
Attention should be drawn to the environmental aspects of battery disposal.
Do not mix different battery types or combine used batteries with new ones.
If the remote control does not operate correctly, or if the operating range becomes re-
duced, replace both batteries with new ones.
If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent battery acid from leaking into the battery compartment.
•
•
•
•
•
•
•
•
11
English
Usage Notice
Following information is only for EU-member states:
[Disposal of batteries and/or accumulators]
The crossed out wheeled dust bin symbol indicates that batteries and/or accu-
mulators must be collected and disposed of separately from household waste.
If the battery or accumulator contains more than the specied values of lead
(Pb), mercury (Hg), and/or cadmium (Cd) dened in the Battery Directive
(2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or
cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure the
proper disposal of products and batteries and thus help to prevent potential
negative consequences for the environment and human health.
For more detailed information about the collection and recycling programmes
available in your country, please contact your local city ofce or the shop
where you purchased the product.
12
English
Usage Notice
Other Information
Copyrights to Images
When projecting images using the projector, be careful not to
infringe the copyright of protected materials.
The following are examples that may infringe the copyright of
protected materials.
Broadcasting images or movies for commercial purposes
Modifying images or movies using functions such as freeze,
magnify, or zoom to broadcast images for commercial purposes or
public viewing
Varying the aspect ratio of images or movies using a function that
changes the screen size to broadcast images for commercial pur-
poses or public viewing
Notes to Users Viewing 3D Images
Pay attention to the following points when viewing images us-
ing 3D glasses with the projector:
How 3D images are viewed may vary according to the individual.
Do not use 3D glasses for viewing any material other than 3D im-
ages.
Before viewing 3D images, make sure to read the manuals provid-
ed with your 3D glasses and 3D compatible content.
Avoid viewing 3D images for a long period of time. Take a break of
15 minutes or longer after every hour of viewing.
If you feel sick while viewing 3D images, stop viewing them. If you
continue to feel sick, consult a doctor.
When viewing 3D images in a room where an LED lighting system
or uorescent lights are used, you may feel that the light in the
room ickers. If this is the case, dim the lights until you do not
notice any ickers, or turn off the lights.
If you or any member of your family has a history of light-sensitive
seizures, consult a doctor before viewing 3D images.
•
•
•
•
•
•
•
•
•
•
13
English
Introduction
Product Features
Outstanding features include:
True XGA(1024×768) addressable pixels
Single chip DLP® technology
NTSC3.58/NTSC4.43/PAL(M/N) and SDTV(480i/
576i), EDTV(480p/576p), HDTV(720p/1080i/1080p)
compatible
Multi-Auto functions: Auto detection, Auto image and
Auto saving the adjustments
Full function remote control
User friendly multilingual on screen display
Advanced digital keystone correction and high quality
full screen image re-scaling
Built-in mono 8-Watt speaker
UXGA, WXGA, SXGA+, SXGA, XGA compression and
VGA re-sizing
■
■
■
■
■
■
■
■
■
14
English
Introduction
Power Cord RGB Cable
Wireless Remote ControlProjector with lens cap
Package Overview
This projector comes with all the items shown below. Check to
make sure your unit is complete. Contact your dealer immedi-
ately if anything is missing.
Due to the difference
in applications for
each country, some
regions may have
different accessories.
N
o
t
e
Documentation:
CD-ROM User’s Manual(*)
User’s Manual
Batteries for Remote
Control (AAA/R03)
Carrying Bag
(*) This supplied
CD-ROM contains
an user's manual
in PDF format and
Projector Manage-
ment Utility.
N
o
t
e
15
English
Introduction
Control panel
Lamp cover
Zoom lever
Ventilation (inlet)
Speaker
Focus ring
Ventilation (outlet)
Remote sensor
Lens cap
Lens
Connection ports
Adjustable feet
Filter
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Product Overview
1
8
4
9
6
3
7
11
12 12
10
2
8
5
13
16
English
Introduction
Connection Ports
LAN terminal
DVI-D In terminal
HDMI In terminal
Computer 1 In terminal
Monitor Out terminal
S-Video In terminal
Y/PB/PR terminals (Component)
Service Port
AC In socket
Computer 2 In terminal
PC Control terminal (RS232 Compliant)
Video In terminal
Audio In terminals (From left to right)
(1) For Y/PB/PR (Component)
(2) For Computer 1, Computer 2 and DVI-D
(3) For S-Video and Video
Audio Out terminal
Anti-theft lock hole (Kensington™ Lock)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
2 3 4 5
9 15
61 87
131211 1410
17
English
Introduction
Control Panel
1 Power and
Power indicator
Refer to the “Power On/Off the Pro-
jector” section. (See pages 23~24);
Indicate the projector’s power status.
2 Lamp indicator Indicate the projector’s lamp status.
3 Temp indicator Indicate the inside of the projector’s
temperature status.
4 Volume - Decrease speaker volume.
5Keystone Use or to adjust the image to com-
pensate for distortion caused by tilting
the projector.
6Enter Select or conrm settings.
7Volume + Increase speaker volume.
8Four Directional
Select Keys
Use or or or to select items or
make adjustments to your selection.
9Menu Press “Menu” to launch the Onscreen
display (OSD), or go back to the previ-
ous menu. (See page 29)
10 Input Switch among Computer1, Computer2
, Component, Video, S-Video, DVI and
HDMI.
11 AV Mute Momentarily turn off/on the audio
and video.
9 11
6
8
1
5 4 7
10
32
18
English
Introduction
Remote Control
1 Infrared trans-
mitter
Sends signals to the projector.
2 Indicator
3 Enter Select or con rm settings.
4 Four
Directional
Select Keys
Use or or or to select items or
make adjustments to your selection.
5 AV Mute Momentarily turn off/on the audio
and video.
6Freeze Pause the screen image. Press again to
resume the screen image.
13
16
4
18
17
2
14
7
5
8
10
3
21
11
20
19
22 12
9
6
1
15
23
19
English
Introduction
7 Eco Dim the projector lamp which will
lower power consumption and extend
the lamp life.
8 Volume +/- Increase/decrease speaker volume.
9Video Press “Video” to choose Video in ter-
minal.
10 HDMI Press “HDMI” to choose HDMI in
terminal.
11 Magnify Enlarge part of the screen image. You
cannot use this function when “Native”
is selected in “Aspect” setting.
12 S-Video Press “S-Video” to choose S-Video in
terminal.
13 Power Refer to the “Power On/Off the Projec-
tor” section. (See pages 23~24)
14 Menu Press “Menu” to launch the Onscreen
display (OSD), or go back to the previ-
ous menu. (See page 29)
15 Input Switch among Computer1, Computer2
, Component, Video, S-Video, DVI and
HDMI.
16 Auto Set Automatically adjust the RGB signal
from the computer.
17 Picture Switch the Image mode.
18 Keystone +/- Adjust the image to compensate for
distortion caused by tilting the projec-
tor.
19 Computer1 Press “Computer1” to choose Com-
puter 1 In terminal.
20 Computer2 Press “Computer2” to choose Com-
puter 2 In terminal.
21 Aspect Use this function to choose your de-
sired aspect ratio for the screen.
22 Status Shows the projector’s current status.
(See page 43)
23 Number Key
Press “Input” key
when you want to
select Component or
DVI-D input source.
N
o
t
e
20
English
Introduction
Remote Control Battery Installation
Press rmly and
slide the battery
cover off.
Slip the cover back over the
batteries until it snaps into
place. Do not mix different
types of batteries or new and
old batteries.
Install new batteries (AAA/
R03). Ensure that you have
the batteries’ polarity (+/–)
aligned correctly.
To ensure safe operation, please observe the following precautions :
Use AAA/R03 type battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture or heat.
Do not drop the remote control.
If the battery has leaked in the remote control, carefully wipe the case clean and
install new battery.
Risk of an explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
Remove batteries from remote control when not using for extended periods.
The remote control may fail to operate if the infrared remote sensor is exposed to
bright sunlight or uorescent lighting.
■
■
■
■
■
■
■
■
■
Remote Control Operating Range
Point the remote control
toward the projector (Infra-
red Remote Receiver) when
pressing any button. Maxi-
mum operating range for
the remote control is about
23.0’ (7m) and ±15° in front
of the projector.
1 2 3
23.0’ (7m)
Approx. 15°
21
English
Basic Operations
Lan DVI
Computer In1
Computer In2
HDMI
S-Video
Monitor Out
RS-232
Service
Audio-In Audio-In
Audio-In Audio-Out
Video
YPR
PB
E62405SP
R
Connecting the Projector
Due to the difference
in applications for
each country, some
regions may have
different accessories.
N
o
t
e
To ensure the projector works well with your computer,
please make sure the timing of the display mode is
compatible with your projector. (See pages 53~54)
Use the cables that come with the projector.
1 ......................................................................................... Power cord (supplied)
2 .............................................................................................................. LAN cable
3 ........................................................................................................... DVI-D cable
4 ........................................................................................................... HDMI cable
5 ..................................................................................................Monitor out cable
6 ............................................................................................................Audio cable
7 ............................................................................................RGB cable (supplied)
8 ............................................................................................................. Serial cable
Make sure that the
power plug is fully
inserted into both
the projector AC
inlet and the wall
outlet.
The AC outlet must
be near this equip-
ment and must be
easily accessible.
N
o
t
e
Connect to Computer/Notebook
Monitor Output
1
3 4 5
7
26
8 6
22
English
Basic Operations
Lan DVI
Computer In1
Computer In2
HDMI
S-Video
Monitor Out
RS-232
Service
Audio-In Audio-In
Audio-In Audio-Out
Video
YPR
PB
E62405SP
R
Due to the difference
in applications for
each country, some
regions may have
different accessories.
N
o
t
e
1 ......................................................................................... Power cord (supplied)
2 ........................................................................................................... HDMI cable
3 ............................................................................................................Audio cable
4 ..................................................................................... 3 RCA Component cable
5 ......................................................................................................... S-Video cable
6 .........................................................................................Composite video cable
S-Video Output
DVD player, Set-top Box
HDTV receiver
Make sure that the
power plug is fully
inserted into both
the projector AC
inlet and the wall
outlet.
The AC outlet must
be near this equip-
ment and must be
easily accessible.
N
o
t
e
Connect to AV Equipment
Video Output
2
3
4
1
63
S-Video Output
5
3
23
English
Basic Operations
Powering On the Projector
Ensure that the power cord and signal cable are securely
connected. The Power indicator will turn red.
Remove the lens cap.
Turn on the lamp by pressing “Power” on the control panel
or the remote control. The Power indicator will ash blue.
The startup screen will display in approximately 5 seconds.
After the screen disappears, the Power indicator will turn
blue.
The rst time you use the projector after purchase, the lan-
guage menu is displayed after the startup screen.
(See page 37)
Turn on your source (computer, notebook, video player,
etc.) The projector will detect your source automatically.
1.
2.
3.
4.
Powering On/Off the Projector
Turn on the projec-
tor rst and then the
signal sources.
N
o
t
e
Lens Cap
Power
CAUTION:
Do not look into the lens while the lamp is on. The strong light from the lamp may
cause damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a re due to internal
overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover
or the bottom of the unit. Doing so could result in injury and/or damage the object.
•
•
•
If you connect
multiple sources
at the same time,
press “Input” or
use “Computer1”,
“Computer2”, “S-
Video”, “Video”,
“HDMI” on the
remote control to
switch inputs.
N
o
t
e
2
1
OR
24
English
Basic Operations
Powering Off the Projector
Press the “Power” and you will see a message as below on
the on-screen display.
Press the “Power” again to turn off the projector lamp.
The cooling fan continues to operate for about 60 seconds
for cooling cycle and the Power indicator will ash red.
After cooling down, the light stops ashing, and then the
projector will enter the standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “Power” to restart the projector.
Disconnect the power cord from the electrical outlet and
the projector.
1.
2.
3.
4.
25
English
Basic Operations
Warning Indicator
When the “Temp” indicator lights red, it indicates the
projector has overheated. The projector will automatically
shut itself down.
When the “Lamp” indicator lights red, and you see the
message below displays on-screen, the projector has
detected that the lamp is approaching its end of life. Please
change the lamp as soon as possible or contact your local
dealer or our service center.
When the “Temp” indicator ashes red (0.5 sec on, 0.5 secs
off) and the message below displays on-screen, it indicates
the fan failed. Stop using the projector and disconnect the
power cord from the electrical outlet, then contact your
local dealer or our service center.
26
English
Basic Operations
Adjusting the Projected Image
Adjusting the Position of Projector Image
The projector is equipped with adjustable feet to raise and
lower the image to ll the screen.
Use to ne-tune the display angle.
1.
You can raise the
projector front up to
7 degrees by rotating
the adjustable feet.
N
o
t
e
Front Adjustable feet
Maximum Length: 25mm
1
27
English
Basic Operations
Adjusting the Projector Zoom and Focus
You may turn the zoom lever to zoom in or out. To focus the
image, rotate the focus ring until the image is clear.
Focus at distances from 4.3 to 48 feet (1.3 to 15 meters).
Focus Ring
Adjusting Projection Image Size
Zoom Lever
Width
Height
Diagonal
Side View
Projection Distance (D)
Screen Screen (H)
Offset (Hd)
Projection Image Size from 32” to 300” (0.8 to 7.6 meters).
28
English
Basic Operations
Diagonal
length (inch)
Screen Size WxH Projection Distance (D) Offset (Hd)
(m) (inch) (m) (feet)
Width Height Width Height wide tele wide tele (m) (feet)
32 0.65 0.49 25.6 19.2 1.3 1.6 4.3 5.1 0.10 0.3
40 0.81 0.61 32.0 24.0 1.6 2.0 5.3 6.4 0.12 0.4
60 1.22 0.91 48.0 36.0 2.4 2.9 8.0 9.6 0.18 0.6
70 1.42 1.07 56.0 42.0 2.8 3.4 9.3 11.2 0.21 0.7
80 1.63 1.22 64.0 48.0 3.3 3.9 10.7 12.8 0.24 0.8
90 1.83 1.37 72.0 54.0 3.7 4.4 12.0 14.4 0.27 0.9
100 2.03 1.52 80.0 60.0 4.1 4.9 13.3 16.0 0.30 1.0
120 2.44 1.83 96.0 72.0 4.9 5.9 16.0 19.2 0.37 1.2
150 3.05 2.29 120.0 90.0 6.1 7.3 20.0 24.0 0.46 1.5
180 3.66 2.74 144.0 108.0 7.3 8.8 24.0 28.8 0.55 1.8
250 5.08 3.81 200.0 150.0 10.2 12.2 33.3 40.0 0.76 2.5
300 6.10 4.57 240.0 180.0 12.2 14.6 40.0 48.0 0.91 3.0
This table is for user’s reference only.
29
English
User Settings
The Projector has a multilingual On Screen Display that al-
lows you to make image adjustments and change a variety of
settings.
How to operate
To open the OSD, press “Menu” on the Control Panel or Remote
Control.
When OSD is displayed, use keys to select any item in the
main menu. While making a selection on a particular page, press
key to enter sub menu.
Use keys to select the desired item in the sub menu and
press “Enter” to adjust the settings by or key. To
exit from adjusting the item, press “Enter” again.
If “to setting” word is shown in the setting, you can press “Enter”
to enter another sub menu. Press “Menu” to close the sub menu
after adjustment.
After adjusting the settings, press “Menu” to go back to the main
menu.
To exit, press “Menu” again. The OSD will be closed.
1.
2.
3.
4.
5.
6.
Using the On Screen Display (OSD)
If no button opera-
tion is made for 10
seconds, the OSD
will be closed auto-
matically.
N
o
t
e
Sub Menu
SettingMain Menu
30
English
User Settings
Image Adjustment
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
Press the to decrease the contrast.
Press the to increase the contrast.
Brightness
Adjust the brightness of the image.
Press the to darken image.
Press the to lighten the image.
Color Saturation
Adjust a video image from black and white to fully saturated
color.
Press the to decrease the amount of color in the image.
Press the to increase the amount of color in the image.
Sharpness
Adjust the sharpness of the image.
Press the to decrease the sharpness.
Press the to increase the sharpness.
Noise Reduction
Adjust the screen noise reduction level.
“Sharpness”, “Noise
Reduction”and
“Color Saturation”
functions are only
supported under
Video/S-Video/
Component signal
sources.
N
o
t
e
31
English
User Settings
Picture Mode
There are many factory presets optimized for various types of im-
ages. Use the or to select the item.
Bright: Mode for emphasizing brightness.
Standard: Mode for optimizing the balance between bright-
ness and color reproduction.
Natural: Mode for emphasizing color reproduction.
R-level
Use the or to adjust the red signal level.
G-level
Use the or to adjust the green signal level.
B-level
Use the or to adjust the blue signal level.
RGB Input Range
Adjust the color range of the HDMI image data.
Auto: Automatically detect RGB range.
Standard: Process the input image as standard color range
data.
Full: Select this mode when computer signal or full range
signal from AV equipment is input.
Auto Set
Automatically synchronize the computer signal.
Position
Refer to next page.
“RGB Input Range”
is only supported
under HDMI source.
N
o
t
e
32
English
User Settings
Image Adjustment|
Position
Phase
Eliminate icker from the image displayed. Use the or to
adjust the value.
Frequency
Adjust the number of total dots in one horizontal period. Use the
or to adjust number to match your PC image.
H-position (Horizontal Position)
Press the to move the image left.
Press the to move the image right.
V-position (Vertical Position)
Press the to move the image down.
Press the to move the image up.
“Position” is only
supported for
Analog RGB signal
which is input from
Computer1 or Com-
puter2.
N
o
t
e
33
English
User Settings
Display Settings
Aspect
Use this function to choose your desired aspect ratio.
Normal: Enlarge an input image to t the screen without
changing the aspect ratio of video signals.
Full: Displays an input image in 1024 × 768 dot resolution by
enlarging it to ll the entire screen.
16:9: Displays an input image in the center of the screen with a
16:9 aspect ratio.
Zoom: Display 4:3 center area of 16:9 signal. (If input signal is
4:3 signal, displayed picture is stretched horizontally.)
Native: Displays an input image in the native resolution of the
video signals. Native display is not available for Y/PB/PR,
Video and S-Video input images.
Display Position
Lets the projected images shift vertically when the screen size set-
ting is “16:9” display (within the range of XGA-1024 × 768).
Wall Color Correction
Use this function to choose a wall color from “Off”, “Whiteboard”,
“Beige”, “Blackboard(Green)” and “Gray”.
Background on NoSignal
Use this feature to display a “Logo”, “Blue” or “None”, screen
when no signal is available.
Display Icon
Choose “On” to display icons as function guides. Choose “Off” to
hide icons.
34
English
User Settings
Start-up Screen
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
On: Display the startup screen.
Off: No logo is displayed.
User Logo
User logos can be displayed in the start-up screen or as the back-
ground when there are no input signals.
Register Logo: Project the image to be registered as a user
logo, and then execute this function.
How to capture the image:
Find the image from input source.
Project the image.
Choose [Register Logo --> Execute], and select [OK]
Choose [Register Logo --> Execute], and select [OK]
Start capturing the screen.
Start capturing the screen.
When nished, it will show the message below.
1.
2.
3.
4.
5.
It takes up to 120
seconds to capture
the picture. This may
vary by resolution of
the input signal.
N
o
t
e
35
English
User Settings
Conrm Logo: Display the registered user logo.
Reset Logo: Return to the default logo.
Image format:
Only capture of external source is supported.
Capture of background color is not supported.
If the source image resolution is bigger than 2368512 bytes (24-bit WXGA image
resolution) image size, the splash image will be captured after center-cropping the
source image to a maximum of 2368512 bytes by retaining the source aspect ratio.
If user had been captured image, the image data captured will be overwritten by the
new one.
3D image is not supported.
•
•
•
•
•
36
English
User Settings
Default Settings 1
Power Off on No Signal
Sets the countdown timer interval. The countdown timer will
start, when there is no signal being sent to the projector. The
projector will automatically power off when the countdown has
nished.
Auto Input Search
When this function is turned “On”, the projector will search for
other signals if the current input signal is lost. When this function
is turned “Off”, it will only search a speci ed connection port.
Power On Method
Sets whether to turn on the power when the ON/STANDBY but-
ton is pressed (Manual), or when the main power switch is turned
on (Auto).
Standby Energy Saving
High: Choose “High” to save standby power (less than 0.5W).
Monitor Out port and LAN control function will be disabled
in standby mode.
Low: Choose “Low” to return to normal standby mode.
Lamp Power
Eco: Choose “Eco” to lower lamp power consumption and
extend the lamp life.
Stnd: Standard mode.
If [Power on Meth-
od] is set to [Auto],
then if the power is
supplied when re-
stored after a power
outage, the projector
will come on.
N
o
t
e
37
English
User Settings
Control Method
PC Control: Allow PC control using PC control terminal.
(Default setting)
LAN: Allow projector control via web browser (Internet Ex-
plorer) using the network.
Language
Choose the multilingual OSD. Press into the sub menu and
then use the or or or key to select your preferred lan-
guage. Press “ENTER” to nalize the selection.
Projection Mode
Stnd. (Standard)
The factory default setting. The image is projected straight on
the screen.
Rear
The projector reverses the image from left to right when you
project behind a translucent screen.
Ceiling
The projector turns the image upside down when using the
ceiling-mounted projection.
Rr-Ceil. (Rear Ceiling)
The projector reverses the image from left to right and turns
the image upside down at the same time. You can project from
behind a translucent screen with ceiling mounted projection.
38
English
User Settings
Default Settings 2
High Altitude Mode
When “On” is selected, the fans will spin faster. Set High Alti-
tude mode to “On” when the projector is used over 2500ft (750m)
elevation.
Key Lock
When the keypad lock function is “On”, the control panel will be
locked other than “Power” key. However, the projector can be op-
erated by the remote control. By selecting “Off”, you will be able
to reuse the control panel.
Password
Register Password:
First time
Choose [Register Password--> Execute], and press “EN-
TER” to set the password.
Enter default password “000000” and press “ENTER” to
con rm.
■
1.
2.
Password default
value is “000000”
( rst time).
N
o
t
e
39
English
User Settings
Enter the new password and press “ENTER” to conrm.
Enter new password again and press “ENTER” to conrm.
Change Password
Press “ENTER” to input old password.
Use number button to enter current password and then
press “ENTER” to conrm.
Enter new password (6 digits in length) using the number
buttons on the remote, then press “ENTER” to conrm.
Enter new password again and press “ENTER” to conrm.
If the incorrect password is entered 5 times, the projector will automatically shut
down.
If you have forgotten your password, please contact your local ofce for support.
•
•
Register Protection: Choose “On” to use security verication
when the turning on the projector. Choose “Off” to be able to
switch on the projector without password verication.
Closed Caption
This projector supports a special feature called closed captioning
which allows subtitles to be displayed at the bottom of the picture.
This is pursuant to the Regulations set forth by the US Federal
Communications Commission (FCC).
Off: Select “Off” to turn off the closed captioning feature.
CC-1: CC-1 language including American English.
CC-2: CC-2 language including Spanish, French, Portuguese,
German and Danish. (depending on the TV channel of the
user)
3.
4.
■
1.
2.
3.
4.
The password has to
be 6 digits.
Use number button
on the remote to
enter your new
password and then
press “Enter” key
to conrm your
password.
N
o
t
e
40
English
User Settings
Due to the different broadcasting or signaling system, it may not operate correctly in
other regions or countries where TV programs do not support closed captioning.
Closed Caption may not appear correctly depending on the signal conditions or the
recording conditions of videotapes.
When you switch channels of broadcasting programs or play a videotape using “trick
play” functions such as rewind or fast-forward, the operations in the connected device
may cause the Caption to remain on the screen for a while.
Closed Caption is available for Video and S-Video input images.
3D Projection
Refer to next page.
Network Setting
Refer to page 42.
Reset All
Return the adjustments and settings to the factory default values.
41
English
User Settings
Default Settings 2 |
3D Projection
3D Projection
Off: Choose “Off” to display normal (2D) picture.
On: Choose “On” to display 3D format.
DLP Link
Select “On” to display 3D image viewing with DLP Link 3D
glasses. Optional sold 3D glasses uses DLP link system to syn-
chronize with the product. Set DLP Link “On” when the optional
3D glasses are used.
L/R Reverse
Normal: Choose “Normal” for default frame contents.
Reverse: Choose “Reverse” to invert left and right frame con-
tents. Choose “Reverse” if viewing image is not natural or felt
3D incorrect.
Compatible 3D
source, 3D content
and active shutter
glasses are required
for 3D viewing.
“L/R Reverse” is
only available when
3D is enabled and
this mode 3D is for
DLP link glass only.
This setting may
need to change when
re-start running 3D
movie.
HDMI input of the
projector does not
support 3D image
transmission in
HDMI standard.
3D image can’t be
displayed when a 3D
Blu-ray disc player is
directly connected to
the HDMI terminal.
N
o
t
e
42
English
User Settings
Default Settings 2 |
Network Setting
Connection Status
Display the network connection status.
MAC Address
Display MAC address.
DHCP
If you change the setting from one to another, when you exit the
OSD menu, the new setting will take effect on next open.
Enable: Assign network settings to the projector from a DHCP
server automatically.
Disable: Assign network settings such as an IP address manu-
ally.
IP Address
Set an IP address . Using number key on the remote control. Or
display IP address provided from DHCP server when DHCP is
set to “Enable”.
Subnet Mask
Set subnet mask number. Using number key on the remote con-
trol. Or display IP address provided from DHCP server when
DHCP is set to “Enable”.
Default Gateway
Set the default gateway of the network connected to the projector.
Using number key on the remote control. Or display IP address
provided from DHCP server when DHCP is set to “Enable”.
Set
Select “OK” to apply the setting.
Be sure to set
“Control Method” to
“LAN” before start-
ing to set Network
setting.
N
o
t
e
43
English
User Settings
Display Status
Input
Input source name.
Resolution
Resolution (in dots).
Picture Mode
Display the setting of Picture mode.
Lamp Time
Time of lamp use.
Total Time
Total Time, including Eco mode and Standard mode.
Lamp Reset Count
Display the number of projector replacement lamps.
Firmware Version
Display Firmware version.
44
English
Controls via Network
Be sure to set “Control Method” to “LAN” before starting to set Net-
work setting.
Check IP address in Default setting 2 > Network setting menu in
OSD. (See page 42)
Open your web browser and type in the IP address you checked.
For example, type “http://192.168.0.100” when IP address is
displayed as the screen above. Then the web page will display as
below:
2.1 Login:
PJ X5260
2.1-1 Select a user. “Administrator” is with high authority
that can process more operations such as network
setting and alert setting. And “User” is with normal
authority.
2.1-2 Input your password. (See note for the default pass-
word.)
2.1-3 Click “Login” button to login. There will be a prompt
if your password is wrong. With correct password,
you can enter to control pages.
2.2 Home: This is a web page which shows basic information of
your projector. There are 5 tabs and you can click a tab for
speci c controls. For more information, you can download a
manual of web control function from download page of the
following URL.
http://www.ricoh.com/
PJ X5260
1.
2.
■
■
■
How to use web browser to control your projector
Set “Standby Energy
Saving” to “Low” if
you want to turn on
the projector from
web browser.
N
o
t
e
- This web page is
available only in
English.
- The default pass-
word for “Admin-
istrator” is “admin”
and the default
password for “User”
is “user”.
N
o
t
e
45
English
Controls via Network
Managing the Projector Using Projector Management
Utility
Projector Management Utility conforms to the PJLink class 1 stan-
dards, and is compatible with all class 1 commands.
A maximum of 100 projectors connected to the network can be man-
aged using one computer.
Projector Management Utility operating environment is described
below.
Supported operating system
Windows XP SP3 (32-bit version) Professional Edition, Home
Edition
Windows Vista (32-bit version) Ultimate, Business, Home Pre-
mium, Home Basic
Windows 7 (32-bit version) Home Premium, Professional, Ulti-
mate, Enterprise
Memory size
Recommended memory size for the operating system of the com-
puter you are using
Display resolution
800 × 600 pixels or more
Installing Projector Management Utility
Projector Management Utility is included on the supplied CD-ROM.
Log in to the computer with administrator privileges to install or
uninstall utilities.
Close all applications.
Insert the CD-ROM in the CD-ROM drive of your computer, and
then click [Exit] on the launcher screen.
Open the “Projector Management Utility” folder stored on the
CD-ROM.
Double-click “setup.exe” stored in the “Projector Management
Utility” folder.
Install the application by following the on-screen instruction.
When the installation is complete, exit the installer.
A shortcut icon is created on the desktop.
•
•
•
•
•
•
1.
2.
3.
4.
5.
6.
This software is
to control and
monitor projectors
manufactured by
our company. The
software may not
work properly when
used to control other
projectors.
N
o
t
e
To uninstall Projec-
tor Management
Utility, use the pro-
gram delete function
in [Control Panel]
to delete “Projector
Management Util-
ity”. Settings about
PJLink controls can
be changed by using
web pages of this
projector. Default
password for PJLink
is “admin”.
N
o
t
e
46
English
Troubleshooting
Problem: No image appears on screen
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure the pins of terminals are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Ensure that the “AV Mute” feature is not turned on.
Problem: Partial, scrolling or incorrectly displayed image
Press “Auto Set” on the remote control.
Adjust the computer display settings. Verify the resolution
setting is less than or equal to 1600 x 1200 resolution. See your
operating system’s Help le.
If you are using a Notebook:
First, follow the steps above to adjust resolution of the com-
puter.
Press the toggle output settings. example: [Fn]+[F3]
If you experience difculty changing resolutions or your monitor
freezes, restart all equipment including the projector.
1.
2.
If you experience trouble with the projector, refer to the follow-
ing information. If the problem persists, please contact your
local dealer or service center.
PANASONIC, NEC => Fn+F3
HP, SHARP, TOSHIBA => Fn+F5
IBM, SONY => Fn+F7
DELL, EPSON => Fn+F8
FUJITSU => Fn+F10
APPLE => F7
47
English
Troubleshooting
Problem: The screen of the Notebook or PowerBook com-
puter is not displaying a presentation
If you are using a Notebook PC:
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s documentation for detailed
information.
Problem: Image is unstable or ickering
Adjust the “Phase” or “Frequency” to correct it. Refer to the “Im-
age Adjustment| Position” section for more information.
Check and recongure the display mode of your graphic card to
make it compatible with the product.
Problem: Image is out of focus
Adjust the Focus Ring on the projector lens.
Make sure the projection screen is between the required distance.
(refer to pages 27~28)
Problem: The image is stretched when displaying 16:9 DVD
Change “Aspect” by pressing the key on remote control or OSD menu
to show image with proper aspect ratio.
Problem: Image is too small or too large
Adjust the Zoom lever on the top of the projector.
Move the projector closer to or further from the screen.
Press “Aspect” button on the remote control or press “Menu”
button on the projector panel, go to “Display Settings --> Aspect”
and try the different settings.
48
English
Troubleshooting
Problem: Image is reversed
Select “Default Settings 1-->Projection Mode” from the OSD and
adjust the projection direction.
Problem: Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will
not turn on until the lamp module has been replaced. To replace
the lamp, follow the procedures in the “Replacing the Lamp”.
(refer to page 51)
49
English
Troubleshooting
Message
POWER
indicator
TEMP
indicator
LAMP
indicator
(Red/Blue) (Red) (Red)
Standby (Input power cord) (Red)
Normal (Power on) (Blue)
Powering up (Warming up) Flashing Blue (0.5 sec)
Power off (Cooling Down) Flashing Red (0.5 sec)
Temperature Error (Over temp. On
Event) (Blue)
Temperature Error (Over temp. On
Standby) (Red)
Lamp Error (Lamp failed On
Event) (Blue)
Lamp Error (Lamp failed On
Standby) (Red)
Error (Fan failed On Event) (Blue) Flashing
Error (Fan failed On Standby) (Red) Flashing
Error (Color Wheel fail / Striking
Lamp Fail On Event) (Blue) Flashing
Error (Color Wheel fail / Striking
Lamp Fail On Standby) (Red) Flashing
Problem: Indicator lighting message
Steady light =>
No light =>
N
o
t
e
50
English
Troubleshooting
Problem: Message Reminders
Temperature Error - the projector is overheat inside. Check the
environmental condition.
Replacing the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
Fan Error - the cooling system fan is not working.
51
English
Replacing the lamp
The projector will detect the lamp life itself. It will show you a
warning message.
When you see this message, change the lamp as soon as possi-
ble. Make sure the projector has been cooled down for at least
60 minutes before changing the lamp.
Warning: To avoid
burns, allow the
projector to cool for
at least 60 minutes
before you replace the
lamp!
Warning: Do not drop
the lamp module or
touch the glass parts.
The glass parts may
shatter and cause
injury if it is dropped.
Warning: For con-
tinued safety replace
with a lamp of the
same type.
Caution: If the lamp
should break, handle
with care to avoid
injury due to broken
pieces and contact
your sales representa-
tive for repair service.
Used Lamps
This projector’s lamp contains trace amounts of environmentally
harmful inorganic mercury. Be careful not to break used lamps, and
dispose of them in accordance with local regulations or contact your
sales representative.
Lamp Replacing Procedure:
Switch off the power to the projector by pressing the “Power”.
Allow the projector to cool down at least 60 minutes.
Disconnect the power cord.
Use a screwdriver to remove the 4 screws from the cover.
Push up and remove the lamp cover.
Remove the protection lm.
Loosen the 3 screws from the lamp module and pull up the
lamp bar.
Pull out the lamp module by force.
Install the new lamp module by reversing the previous steps.
See the lamp’s manual for instructions on resetting the lamp time.
1.
2.
3.
4.
5.
6.
7.
8.
9.
1
1
3
4
5
2
52
English
Cleaning the lter
We recommends cleaning the dust lter every three months;
clean it more often if the projector is used in a dusty environ-
ment.
Cleaning the Filter Procedure:
Switch off the power to the projector by pressing the “Power”.
Disconnect the power cord.
Remove the lter slowly and carefully.
Clean or replace the lter.
To install the lter, reverse the previous steps.
1.
2.
3.
4.
1
2
53
English
Appendices
List of Compatible Signals
PC Signal / HDMI Signal
Modes Resolution V.Frequency
(Hz)
H.Frequency
(kHz)
VGA 640 x 350 70 31.5
640 x 480 60 31.5
640 x 480 70 35.0
640 x 480 72 37.9
640 x 480 75 37.5
720 x 400 70 31.5
720 x 576 60 35.91
SVGA 800 x 600 56 35.2
800 x 600 60 37.9
800 x 600 72 48.1
800 x 600 75 46.9
800 x 600 85 53.7
XGA 1024 x 768 60 48.4
1024 x 768 70 56.5
1024 x 768 72 57.67
1024 x 768 75 60
WXGA 1280 x 768 60 47.4
1280 x 768 75 60.3
1280 x 720 60 45
1280 x 720 70 52.5
1280 x 720 72 54.07
1280 x 720 75 56.46
1280 x 800 60 49.702
1280 x 800 75 62.8
SXGA 1152 x 864 60 53.5
1152 x 864 70 63.8
1152 x 864 72 64.87
1152 x 864 75 67.5
1280 x 1024 60 63.98
1280 x 1024 70 77.90
1280 x 1024 72 79.98
1280 x 1024 75 91.15
1280 x 960 60 60.0
1280 x 960 70 69.93
1280 x 960 72 72.07
1280 x 960 75 75.23
54
English
Appendices
PC Signal / HDMI Signal
SXGA+ 1400 x 1050 60 63.98
1440 x 900 60 65.32
1440 x 900 75 70.64
UXGA 1600 x 1200 60 75
MAC LC 13” 640 x 480 66.66 34.98
MAC 16” 832 x 624 74.55 49.725
MAC 19” 1024 x 768 75 60.24
MAC 1152 x 870 75.06 68.68
MAC G4 640 x 480 60 31.35
i Mac DV 1024 x 768 75 60
i Mac DV 1152 x 870 75 68.49
i Mac DV 1280 x 960 75 75
55
English
Appendices
Congurations of Terminals
Terminal: Computer in 1/2 (Mini D-sub 15
pin)
1Red (R/Cr) Input/R Output 9 DDC 5V / NC*
2Green (G/Y) Input/G Output 10 Ground (Ver. sync.)
3Blue (B/Cb) Input/B Output 11 NC*
4NC* 12 DDC Data / NC*
5 Ground (Horiz.sync.)
13 Horiz. sync. Input /
Output (Composite H/V sync. Input)
6Ground (Red)
7 Ground (Green) 14 Vert. sync. Input / Output
8Ground (Blue) 15 DDC CLK / NC*
* Do not connect anything.
54321
10 9 8 7 6
15 14 13 12 11
Terminal: PC Control (D-sub 9 pin)
54321
9876
1NC* 6 NC*
2TXD (Sending Data) 7NC*
3RXD (Receiving Data) 8 NC*
4NC* 9 NC*
5 GND * Do not connect anything.
Contact your dealer
for control cable and
commands.
N
o
t
e
56
English
Appendices
List of general specications■
Item
Specication
Consumption Power
290W (ECO mode) / 384W (Full mode)
Weight
14.3lbs (6.5kg)
Dimensions (WxHxD)
398×147×311mm (with protruding parts)
Environmental Considerations
Operational Temperatures: 41° to 95°F (5° to 35°C),
20% to 80% humidity (non-condensing)
Storage Temperatures: -4° to 140°F (-20° to 60°C),
20% to 80% humidity (non-condensing)
Projection System
Single DLP® 0.7” chip
Resolution
1024 × 768 pixels (XGA)
Lens
F# 1.77~1.93, f=28.64 mm ~ 34.35 mm, 1.2X Zoom Lens
Lamp
High-pressure mercury lamp (300W)
Lamp Life
2000 hours typical (Full Mode)
2500 hours typical (ECO Mode)
Projection screen size
32 ~ 300 inch
Projection distance
1.3 ~ 15m (Focus range)
Speaker
8W (Mono)
Connection terminal
Computer In terminal x2
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
Monitor Out terminal
Mini D sub 15 pin
HDMI terminal
HDMI type A connector
S-Video terminal
Mini DIN 4 pin
Video terminal
RCA Pin Jack
Audio In terminal ×3
3.5 mm diameter mini-jack
(1) Y/PB/PR (Component)
(2) Computer 1 / Computer 2 / DVI-D (multiple use)
(3) S-Video / Video (dual use)
Audio Out terminal
3.5 mm diameter mini-jack
DVI-D terminal
DVI-D (HDCP supported)
Y/PB/PR terminal
RCA Pin Jack x 3 (Component)
PC Control terminal
D sub 9 pin male (RS-232C Compliant)
LAN terminal
RJ-45
N
o
t
e
This model complies with the above specications.
Designs and specications are subject to change without notice.
This model may not be compatible with features and/or specications that may be added in the
future.
Separately sold product
PJ Replacement Lamp Type 8
■
Specications
57
English
Appendices
Trademarks
DLP is trademarks of Texas Instruments.
IBM is a trademark or registered trademark of International
Business Machines Corporation.
Macintosh, Mac OS X, iMac, and PowerBook are trademarks
of Apple Inc., registered in the U.S. and other countries.
Microsoft, Windows, Windows Vista, Internet Explorer and
PowerPoint are either a registered trademark or trademark
of Microsoft Corporation in the United States and/or other
countries.
HDMI, the HDMI Logo and High-Denition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
Other product and company names mentioned in this user’s
manual may be the trademarks or registered trademarks of
their respective holders.
•
•
•
•
•
•
© 2012
EN GB
Y017-6220
User’s Manual
