Ricoh WLALT01 Wireless LAN Module User Manual 05 Rev x
Ricoh Company Ltd Wireless LAN Module 05 Rev x
Ricoh >
Contents
- 1. (Short-term Confidential)User Manual
- 2. User Manual
(Short-term Confidential)User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1801438 |
| Application ID | vgWid1IXOMJfMrW1kO/Lfg== |
| Document Description | (Short-term Confidential)User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 5.57kB (69628 bits) |
| Date Submitted | 2012-09-25 00:00:00 |
| Date Available | 2013-03-24 00:00:00 |
| Creation Date | 2012-09-21 18:02:57 |
| Producing Software | Acrobat Distiller 9.3.3 (Windows) |
| Document Lastmod | 2012-09-21 18:02:57 |
| Document Title | Microsoft Word - 05 User Manual (Rev).docx |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | 14539 |
User’s manual Product: Wireless LAN Module Model: LBWB1ZZWU6 FCC ID: BBP-WLALT01 IC: 144D-WLALT01 For OEM integration only – device cannot be sold to general public. Therefore we will not supply the User’s manual, the installation manual is the official for OEM. (Note) This module was granted as FCC/IC Limited Modular Approval. Additional host systems must be required reassessment of Dynamic Frequency Selection and host systems must provide regulated supply voltages to the module. Separate evaluation must be required for any portable configuration. When used in mobile applications, the antennas shown in this filing must be installed to provide a separation distance of at least 20 cm from all persons. OEM integrators and end-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. Only those antennas tested with the device or similar antennas with equal or lesser gain may be used with this transmitter. This device complies with the Dynamic Frequency Selection (DFS) requirements of Report and Order FCC 03-287 as a Client only without Radar Detection. We will ask OEM to include the following Notices required by FCC/ IC on the product and in the User’s manual. ■Requirement of Labeling (For FCC) Please describe the following item on the host device of the this module: Contains Transmitter Module FCC ID: BBP-WLALT01 or Contains FCC ID: BBP-WLALT01 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (For IC) Please describe the following item on the host device of the this module: Contains Transmitter Module IC: 144D-WLALT01 or Contains IC: 144D-WLALT01 ■Requirement of User’s Manual Statement (For FCC) User’s manual shall contain following sentence FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). 5.15-5.25GHz band is restricted to indoor operations only. (For IC) Indicate the following information. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. * It can be also indicated on the equipment in place of the manual - For the transmitter which can replace the antenna by end user Indicate the following information. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. * It is unnecessary if the application document shows end user cannot replace and modify the antenna. Indicate the following information. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna type: Chip dielectric antenna Gain: 2.4GHz: -0.5 dBi, W52/53: -0.3dBi, W56: -1.2dBi, W58: -1.7dBi Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Antenna Type: Chip dielectric antenna Gain: 2.4GHz: -0.5 dBi, W52/53: -0.3dBi, W56: -1.2dBi, W58: -1.7dBi * It is necessary if the equipment has a lot of antennas and end user can select the antenna. *The manufacturer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi) and required impedance for each. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : 14539 Create Date : 2012:09:21 18:02:57+09:00 Modify Date : 2012:09:21 18:02:57+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : 14539 Title : Microsoft Word - 05 User Manual (Rev).docx Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.3.3 (Windows) Document ID : uuid:3b36a7e5-2919-4b92-838e-5a6e9c6eb905 Instance ID : uuid:e1259f30-9362-4603-ab9f-2297d01549ea Page Count : 6EXIF Metadata provided by EXIF.tools