Ricoh WLBRG01 Wireless LAN Module User Manual

Ricoh Company Ltd Wireless LAN Module Users Manual

Users Manual

TYPE-GJ1 Users ManualNovember 16, 2011 TYPE-GJ1 Users Manual 1. Introduction/Overview ...................................................2 2. Block Diagram ..................................................3 3. Hardware specifications ...................................................4 1/8 4.System Requirements ...................................................65.setup ...................................................66.Compliance ...................................................7
1．Introduction 本書は組込み型 Wireless BridgeTYPE-GJ1について説明するものです。 This document describes about “embedded Wireless Bridge TYPE-GJ1. 2．Overview TYPE-GJ1はSingle Band IEEE802.11bgn準拠のインテリジェントモジュールです。本モジュールはEU RoHS 指令2009/95/EC(Lead Free)及び中国版RoHSに適合しています。本モジュールはMAC/BBPチップセットRTL8196CとRTL8188CE(Realtek社)を採用しています。また、このモジュールは1ストリームの11nシステム及び40MHz帯域幅モードをサポートしています。 TYPE-GJ1 is Single Band IEEE802.11bgn intelligent radio module. This module complies with EU RoHS Directive 2009/95/EC(Lead Free) and China RoHS with exemptions. This module has an MAC/BBP Chipset RTL8196C and RTL8188CE (Realtek) internally. Also this module supports high speed one stream 11n technology and 40MHz band width mode. 機能 (Features): - IEEE802.11b/g/n準拠(2.4GHz) IEEE 802.11b/g/n conformity (2.4GHz) - 1ストリーム1 x 1 11nシステム及び40MHz帯域幅モード対応 (スループット理論値 150Mbps) Two stream 1 x 1 11n technology and 40MHz band width mode. (Throughput up to 150Mbps) - データレート 802.11b/g 1-54Mbps, 802.11n MCS0-15対応 Data rates of 1 - 54 Mbps for 802.11b/g and MCS0-15 for 802.11n. - “Short Gard Interval”モード対応 Support “Short Gard Interval” mode. TYPE-GJ1 Users Manual2/8 MCS0-7対応MCS0-7 for 802.11n
3．Block diagram DC 5V in PCIe RTL8196C Realtek SoC TRANS TRANS RJ45 LAN RJ45 WAN RTL8188CE Realtek WLAN Chip Antenna １X1 FROM 4MB DDR 32MB SW WPS/RESET LED X 4（Not Populate） DC/DC No use TYPE-GJ1 Users Manual3/8
Item Specification Unit Note電源コネクタPower connectorMicro B ( USB) －インターフェイスDevice InterfacesIEEE802.3u 10/100BASE 2port －WAN、LAN portIEEE802.11b/g/n －重さWeight13.8 g Typ寸法Dimensions54 x 37 x 18 mm W x H x D, PCB Thickness = 1.0mm* 7.項参照。See section 7.MTBF 90,000 h Min.Item Specification Unit Note保存温度Storage temperature-20 to +60 ℃保存湿度Storage humidityMax 95% %RH Non condensing動作温度Operating Temperature0 to +55 ℃Ambient動作湿度Operating humidity10 to 90 %RH Non condensing4-2．Environmental specifications Item Specification Unit Note電源電圧Power supply voltageMin. Typ. Max.4.75 5.0 5.25 V 動作条件 Operating ConditionsTYPE-GJ1 Users Manual4/8 4-1．General specifications
Item Specification Unit NoteChipset SoC RTL8196C / WLAN RTL8188CE (Realtek) －中心周波数Center frequency11b 2412 – 2472 MHz11g 2412 – 2472 MHz Ch.1～Ch.1311ng HT20 2412 - 2472 MHz11ng HT40 2422 - 2462 MHz Ch.3～Ch.11チャネル間隔Channel spacing11b/11g/11ng HT20/HT40 5 MHz通信レートRateスキームコードScheme code11b 1, 2, 5.5L, 5.5S, 11L, 11S Mbps11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps11ng 1Stream MCS0, 1, 2, 3, 4, 5, 6, 7 －変調方式Modulation type11b DSSS(CCK,DQPSK,DBPSK)－11g/11ng DSSS-OFDM (64QAM,16QAM,QPSK,BPSK)－4-4．Radio configuration and general specifications TYPE-GJ1 Users Manual5/8
TYPE-GJ1 Users Manual 5. System Requirements (for the install) OS: Embedded Linux or Embedded windows PC H/W:Ethernet port is required 6. Setup TYPE-GJ1 connect to the Ethernet port of the END product.The END product can use the wireless LAN by setting it using a special protocol. 6/8 The configuration of this product uses a special protocol.The exhibition of those procedures is kept by contract.H/W:Ethernet port is requiredEDN ProductTYPE-GJIEthernet
TYPE-GJ1 Users Manual7/8 7. Compliance FCC ID：BBP-WLBRG01 NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. IC ：144D-WLBRG01This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meetsthe FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radiofrequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cmor more away from person’s body (excluding extremities: hands, wrists, feet and ankles).Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement noncontrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition dans leSupplément C à OET65 et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doitêtre installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (àl’exception des extrémités : mains, poignets, pieds et chevilles).This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation issubject to the following two conditions: (1) this device may not cause interference, and (2) this device must acceptany interference, including interference that may cause undesired operation of this device.Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doitpas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même sile brouillage est susceptible d'en compromettre le fonctionnement.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to otherusers, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) isnot more than that necessary for successful communication.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenned'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduireles risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et songain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
TYPE-GJ1 Users Manual8/8 FCC WARNING： Antenna information: Omni-directionalChip Antenna Peak Gain 0.5dBiauthority to operate the equipment. Manual and Product Labeling information To The End UserThe end user manual shall include all required regulatory information/warning as show in this manual.And when this module is installed in the host product, you must include a "Contain FCC ID : BBP-WLBRG01" and a “Contain IC: 144D-WLBRG01” in the label of the host product. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada tooperate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use withthis device.Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel decatégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

Navigation menu