Ridgid R8408 Users Manual
R8408 to the manual faac854b-6ffc-4c1f-a9a5-a2c8b9ef86f9
2015-02-04
: Ridgid Ridgid-R8408-Users-Manual-387828 ridgid-r8408-users-manual-387828 ridgid pdf
Open the PDF directly: View PDF 
.
Page Count: 26
1
Your job-site radio/race scanner has been engineered and manufactured to our high standards for dependability, ease of
operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID® product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR’S MANUAL
JOB-SITE RADIO/RACE SCANNER
R8408
BATTERIES AND CHARGERS
SOLD SEPARATELY
2
Introduction .....................................................................................................................................................................2
General Safety Rules .......................................................................................................................................................3
Specific Safety Rules .......................................................................................................................................................4
Symbols ...........................................................................................................................................................................5
Electrical ..........................................................................................................................................................................6
Features ....................................................................................................................................................................... 7-9
Assembly .......................................................................................................................................................................10
Operation ................................................................................................................................................................. 10-21
Maintenance ..................................................................................................................................................................22
Warranty ........................................................................................................................................................................25
Customer Service Information ......................................................................................................................... Back Page
TABLE OF CONTENTS
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
3
GENERAL SAFETY RULES
WARNING!
READ THESE INSTRUCTIONS. Failure to follow
all instructions listed below, may result in electric
shock, fire and/or serious personal injury.
KEEP THESE INSTRUCTIONS
HEED ALL WARNINGS
FOLLOW ALL INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate products in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Products create sparks which may ignite the
dust or fumes.
ELECTRICAL SAFETY
A battery operated product with integral batteries or
a separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a risk
of fire when used with another battery.
Use battery operated product only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire.
Use battery only with charger listed.
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
PERSONAL SAFETY
Avoid accidental starting. Be sure switch is in the locked
or off position before inserting battery pack. Carrying
products with your finger on the switch or inserting the battery
pack into a product with the switch on invites accidents.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the product in unexpected situations.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
product in unexpected situations.
PRODUCT USE AND CARE
Do not use product if switch does not turn it on or
off. A product that cannot be controlled with the switch
is dangerous and must be repaired.
Disconnect battery pack from product or place the
switch in the locked or off position before making
any adjustments, changing accessories, or storing
the product. Such preventive safety measures reduce
the risk of starting the product accidentally.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause sparks, burns,
or a fire.
Keep the radio and its handle dry, clean and free from
oil and grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean the radio.
Following this rule will reduce the risk of loss of control
and deterioration of the enclosure plastic.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Only use attachments/accessories specified by the
manufacturer.
IMPORTANT SAFETY INSTRUCTIONS
MODEL BATTERY PACK CHARGER
R8408
(12 V) 130252002
130254001 140276003
140276004
140276006
(R840091)
(14.4 V) 130254008
130254002
(18 V) 130254007
(18 V) 130383002
(R84008) 140276006
(R840091)
(24 V) 130377001
(R85008) (24 V) 140315001
(R85009)
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
4
SPECIFIC SAFETY RULES
Know your product. Read operator’s manual carefully.
Learn its applications and limitations, as well as the
specific potential hazards related to this product.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Battery products do not have to be plugged into
an electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery product or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not place battery products or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped
or received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush with water
immediately.
Do not charge battery product in a damp or wet
location. Following this rule will reduce the risk of electric
shock.
For best results, your battery product should be
charged in a location where the temperature is
more than 50°F but less than 100°F. To reduce the
risk of serious personal injury, do not store outside or in
vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean water for
at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of serious
personal injury.
To reduce the risk of personal injury and electric
shock, the product should not be played with or
placed where small children can reach it.
To reduce the risk of electric shock, do not expose
to water or rain.
If the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorized
service center to avoid risk.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this product. If
you loan someone this product, loan them these instruc-
tions also.
IMPORTANT SAFETY INSTRUCTIONS
SERVICE
Product service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
When servicing a product, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
5
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SYMBOL SIGNAL MEANING
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
Read The Operator’s Manual
Safety Alert
SYMBOL NAME DESIGNATION/EXPLANATION
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear safety goggles or safety glasses with side shields,
or a full face shield when operating this product.
Precautions that involve your safety.
Wet Conditions Alert
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When
servicing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID® customer service for
assistance.
SAVE THESE INSTRUCTIONS
Electric Shock Alert Indicates uninsulated material within the unit that may cause
electrical shock. Do not remove product covering.
6
DOUBLE INSULATION
Double insulation is a concept in safety in electric products,
which eliminates the need for the usual three-wire grounded
power cord. All exposed metal parts are isolated from the
internal metal motor components with protecting insulation.
Double insulated products do not need to be grounded.
WARNING:
The double insulated system is intended to protect
the user from shock resulting from a break in the
product’s internal wiring. Observe all normal safety
precautions to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the product to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
ELECTRICAL CONNECTION
This product should be connected to a power supply that
is 120 volts, AC only (normal household current), 60 Hz.
Do not operate this product on direct current (DC) through
the power cord. A substantial voltage drop will cause a loss
of power and the motor will overheat. If the product does
not operate when plugged into an outlet, double-check the
power supply.
EXTENSION CORDS
When using a product at a considerable distance from a
power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
When using this product outdoors, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
**Ampere rating (on product data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 —
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools, or other obstructions while you are
working with this product. Failure to do so can
result in serious personal injury.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use a
product with a damaged cord since touching
the damaged area could cause electrical shock
resulting in serious injury.
ELECTRICAL
7
FEATURES
PRODUCT SPECIFICATIONS
Operating Temperature
Normal .........................................................32˚F - 104˚F
Frequency Ranges
AM Band ................................................520-1710 (KHz)
FM Band ........................................... 87.5 - 108.1 (MHz)
Race Band ................ (UHF) 450.0375 - 469.9625 (MHz)
Scan Rate (Race Band) ................16 Channels per second
Scan Delay .............................................. 60 Microseconds
Audio Output
13 Watts nominal into 4 Ω (Ohm) internal speakers
12.5 mW nominal into 32 Ω (Ohm) Headphone
25 mW nominal into 64 Ω (Ohm) Earphone
Power Requirements
120 VAC through cord or 12 V DC, 14.4 V DC, 18 V DC,
and 24 V DC RIDGID slide-mount batteries
3 AA (1.5 V DC) batteries for memory/clock backup
Power Outputs
1 Automotive-type power receptacle, 12 V DC,
1 Amp Max.
External Jacks
Antenna Connector .................. For single-wire antenna
Headphone Jack ................................................3.5 mm
iPod Connector ............ 30-pin iPod docking connector
Input Jack ......................................3.5 mm (Inside door)
Size .................................. 22 in. (L) x 13 in. (H) x 12 in. (W)
Weight ..................................................................... 23.5 lb.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC COMPLIANCE
8
KNOW YOUR JOB-SITE RADIO/
RACE SCANNER
See Figures 1 - 2.
The safe use of this product requires an understanding of the
information on the product and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
12 V DC 1-AMP RECEPTACLE
Charge your cell phone or other electronics that require a
12 V DC connection.
A/C POWER CORD
Your job-site radio/race scanner can be plugged into an A/C
power source.
AUDIO OUT (HEADPHONE/EARPHONE)
CONNECTION
Connect your headphones through the audio out
connection.
Fig. 1
FEATURES
BACKLIT LCD
DISPLAY
CORD
WRAP DIGITAL
CLOCK
FOLD-DOWN ROTATABLE
FLEXIBLE ANTENNA
PROTECTIvE
STEEL ROLL
CAGE
DIGITAL
KEYPAD
iPod
COMPARTMENT
TOP
TRAY
BASS BOOST/SKIP
The bass boost can enhance the bass by three levels when
the radio is in stereo mode. To use the SKIP feature when
in race mode, you can program into memory the channels
you wish to skip over.
BACKLIT LCD DISPLAY
The backlit LCD display is clear and visible in all lighting
conditions.
NOTE: The illustrations of the LCD display shown in this
manual are only examples of the frequencies you may see
and program on your radio/scanner and are not the exact
frequencies that you may choose to listen to and program.
CORD WRAP
Use the convenient cord wrap located on top of the radio
during transport.
DIGITAL CLOCK
Displays the time in hours and minutes.
NON-SKID
FEET
12 v DC 1-AMP
RECEPTACLE AUX 2
INPUT JACK A/C POWER
CORD
AUDIO OUT
(HEADPHONE/EARPHONE)
CONNECTION
30 PIN iPod DOCK
(AUX 1)
9
FEATURES
DIGITAL KEYPAD
Use the digital keypad for direct input of a desired frequency.
With digital tuning, you can preset up to ten of your favorite
stations (in each mode) and store them in memory.
FOLD-DOWN ROTATABLE FLEXIBLE ANTENNA
The antenna rotates to help improve reception. The flexible
design prevents damage from bending. It folds down and
out of the way when not in use.
iPod COMPARTMENT
The iPod compartment, located in the drop-down door on
the front of the radio, helps protect your iPod from jobsite
debris. Inside the compartment, there is a 30-pin iPod
docking connector and retainer strap to help secure your
iPod. When connected, the iPod can be charged even if the
radio is turned off.
PROTECTIVE STEEL ROLL CAGE
The steel roll cage helps protect your radio while in use on
the job site.
RACE MODE
Use the RACE mode to tune into race-affiliated frequencies.
Race mode lets you listen to driver/pit crew communications,
track official/driver communications, and track worker
conversations with drivers, crews and officials.
SQUELCH CONTROL
While in RACE mode, you can reduce interference to improve
the listening quality of stronger signals.
NOTE: Use of the SQUELCH control will affect some tuning
and scanning functions. Refer to these sections in this
manual for details on making adjustments when SQUELCH
is in use.
TOP TRAY
When charging your cell phone or other small items through
the 12 V receptacle, store them in the top tray.
TWEETER
BASS BOOST/SKIP
Fig. 2
STEREO/MONO
TIME
MODE
PRESETS
BASS
BOOST
SKIP
INDICATOR
FREQUENCY
SEEK/SCAN
TWEETER
MODE
SQUELCH
CONTROL
ON/OFF/
vOLUME
DIGITAL
KEYPAD
TUNE
(DOWN) TUNE
(UP)
Backspace
Clear
Direct Tune
HOUR/MINUTE
TIME SET
STEREO/MONO
DIRECT
TUNE
BACKSPACE/
CLEAR
DISPLAY
CONTROLS
10
OPERATION
WARNING:
Do not allow familiarity with this product to make
you careless. Remember that a careless fraction of
a second is sufficient to inflict severe injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.
WARNING:
The job-site radio/race scanner is not waterproof.
To reduce the risk of fire or electrical shock, do not
use near water. Failure to heed this warning can
result in serious personal injury.
UNPACKING
This product has been shipped completely assembled.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
PACKING LIST
Job-site radio/race scanner
AA Batteries (3)
Auxiliary Connection Cable
Operator’s Manual
ASSEMBLY
CAUTION:
Always refer to the manual for any device
recommended for use as an attachment or
accessory. Proper use of any device, when
attached to the job-site radio/race scanner, is the
sole responsibility of the operator. Improper use
may damage the device or the product.
APPLICATIONS
You may use this product for the following purposes:
Listening to AM/FM radio
Listening to race-affiliated broadcasts near an active
racing event
Listening to iPods and other MP3 players, CD players,
and other audio devices
Charging iPods
Charging cell phones or other electronics that require a
12 V DC connection
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Failure to
heed this warning could result in serious personal
injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING:
To prevent accidental starting that could cause
serious personal injury, always remove the battery
pack from the product when assembling parts.
11
CHARGER AND BATTERY PACKS SOLD
SEPARATELY
This product will accept RIDGID 24 V and RIDGID 18 V
lithium-ion battery packs and RIDGID 18 V, 14.4 V, and 12 V
nickel-cadmium battery packs.
NOTE: Do not attempt to use the 9.6 V RIDGID slide-mount
battery pack with the job-site radio, as it will not power the
unit.
For complete charging and battery pack instructions, refer to
the operator’s manuals included with chargers and battery
packs listed in the General Safety Rules for this manual.
NOTE: The radio does not charge battery packs. Battery
packs must be charged in RIDGID brand chargers.
Only the 18 V lithium-ion battery pack will be shown in
the following illustrations. Both types of battery packs are
installed and removed in the same way.
GENERAL USAGE TIPS
RECEPTION
To decrease interference or electrical noise, reception may
be improved by rotating the antenna or moving the radio/
scanner to a higher elevation.
USE OF HEADPHONES/EARPHONES
WARNING:
Use of an incorrect earphone or stereo headset,
or the type of headphone placed directly into the
ear canal, may be potentially hazardous to your
hearing.
Always use the correct type of headphones or earphones to
help prevent discomfort or possible hearing damage if the
volume level increases unexpectedly due to changes in the
volume control or squelch setting.
To listen to the unit privately, headphones or mini-plug
earphones with a 1/8 in. (3.5 mm) plug (not supplied) can
be plugged into the 3.5 mm jack on the top right side of
the unit.
NOTE: Attaching headphones/earphones disconnects the
internal speakers.
OPERATION
Fig. 3
BATTERY
DOOR
AA
BATTERIES
SCREW
A/C CORD
The A/C cord can connect the radio to a power supply when
a battery is not available. An iPod can be charged in the radio
when the A/C cord or battery pack is in use, but the battery
pack cannot be charged by the radio.
Always turn the radio/scanner off before disconnecting it
from the power source.
TO INSTALL/REPLACE CLOCK/MEMORY
BATTERIES
See Figure 3.
It is advisable to write down saved channels before replacing
the clock batteries.
There is a 15-second time frame for replacing the AA
batteries. If batteries are not replaced within 15 seconds,
the radio will lose all settings previously stored in memory,
and they will require reprogramming.
Always use new batteries for replacement.
Remove the screw from the battery cover located on the
bottom of the radio.
Remove the battery cover.
Install three new AA batteries according to polarity
indicators inside the battery compartment.
Replace the battery cover and secure with the screw.
12
OPERATION
TO INSTALL/REMOVE BATTERY PACK
See Figure 4.
The radio’s battery port will accept RIDGID 12 V, 14.4 V and
18 V NiCd battery packs and 18 V and 24 V Li-ion battery
packs. The 18 V Li-ion battery pack is shown.
NOTE: Do not attempt to use the 9.6 V RIDGID slide-mount
battery pack with the job-site radio, as it will not power the
unit.
Place the battery pack in the radio, aligning the raised rib
on the battery pack with the groove in the radio’s battery
port.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured to the
radio before beginning operation.
Depress the latches on both sides to release the battery
pack from the radio.
NOTE: Leaving the battery pack connected for long
periods of time will drain the battery pack. Always
disconnect battery packs after use.
12 V DC 1-AMP RECEPTACLE
See Figure 5.
The 12 V DC receptacle can be used as a power source
for powering small, low current (less than 1 [one] Amp DC)
devices such as cell phone chargers, CD players, etc.
CAUTION:
Do not connect any devices that require more than
1 (one) Amp to operate. Doing so will trip a self-
resetting function and disable the receptacle.
CAUTION:
Output wiring of the receptacle is center positive.
Make sure the device you wish to connect has a
compatible connector as shown in figure 5.
NOTE: When charging small electronics through the 12 V
receptacle, be sure the battery pack inserted in the radio
is greater than 12 V, or plug the radio into a power supply
using the A/C cord.
WARNING:
Always keep the 12 V DC receptacle covered with
the receptacle cover when not in use. Failure to
heed this warning could result in serious injury.
Fig. 4
LATCH(ES)
DEPRESS LATCHES TO
RELEASE BATTERY PACK
BATTERY
PACK
Fig. 5
12 v DC 1-AMP
RECEPTACLE
OUTPUT WIRING OF RECEPTACLE IS CENTER POSITIvE
RECEPTACLE
COvER
13
OPERATION
RADIO ON / vOLUME AT 10
RADIO OFF / vOLUME AT 0
Fig. 7
WIRE-STYLE FM ANTENNA (OPTIONAL)
See Figure 6.
The radio has a connection point for a standard wire-style
antenna for improving indoor FM reception.
For best results, use a simple 1-meter (39.4 in.) length of 22
AWG stranded or solid copper wire. If the wire is insulated,
strip one end to expose at least 1/2 in of the conductor.
NOTE: The wire is not included with this product.
To attach a wire-style antenna, loosen the single screw in
the center of the connector and insert the stripped end of
the antenna wire into one side of the connector. Tighten
the screw.
NOTE: The wire-style antenna works for FM BAND stations
only.
LCD DISPLAY
See Figure 7.
When the radio is not connected to a power supply, the LCD
display will remain off. If the radio is connected to a power
supply but in the OFF position, one LED will light the display.
If the radio is connected to a power supply and in the ON
position, three LEDs will light the display. You can view the
time, frequency, and settings in use on the LCD display.
NOTE: The LCD display will be partially lit when a battery
pack is connected as a power supply. Always disconnect
battery packs after use to prevent draining the battery
pack.
TURNING THE RADIO ON/OFF
See Figure 7.
Push the ON/OFF/VOLUME knob and hold down for one-
half (0.5) second to turn the radio ON or OFF.
When the radio is OFF, only the time is displayed with colon
( : ) blinking at one-second intervals.
ADJUSTING THE VOLUME
See Figure 7.
When the radio is turned ON, the sound level will default
to Level 2 and will be displayed for one second. After one
second, the radio frequency will be displayed.
To increase the volume: turn the ON/OFF/VOLUME knob
to the right.
To decrease the volume: turn the ON/OFF/VOLUME knob
to the left.
Fig. 6
WIRE-STYLE
ANTENNA
SCREW
STRIPPED END
OF WIRE
14
OPERATION
Fig. 9
MODE SELECTION
See Figure 8.
Press the MODE button above the display until the desired
mode is selected. There are five modes:
FM mode
AM mode
RACE mode - For listening to race-affiliated
frequencies
AUX 1: For the 30-PIN iPod connection in the door
AUX 2: For the 3.5 mm input jack located inside the iPod
compartment
To select and scroll through modes, press the MODE button.
The selected mode will be displayed on the left side of the
LCD display.
NOTE: When turned on, the radio will return to the last mode
that was used.
MANUAL TUNING - ALL MODES
See Figure 9.
The left and right arrow buttons located below the LCD
display are used to manually tune to the desired radio
frequency. The selected frequency is displayed on the
LCD.
Press the left arrow button to tune to a lower frequency
and press the right arrow button to tune to a higher
frequency.
Briefly push either button (not press and hold) to tune one
frequency step at a time.
To scroll through frequencies quickly, press and hold
the desired arrow button. To stop scrolling, release the
button.
SEEK/SCAN (AM & FM MODES)
See Figure 10.
Use the SEEK/SCAN button to quickly find audible
frequencies. Each frequency with clear reception can be
viewed on the LCD display.
To use the SEEK feature:
Press the button once to tune to the next higher frequency
with clear reception.
To use the SCAN feature:
Press and hold the button for two seconds to scan
through all the frequencies with clear reception.
NOTE: When scanning, the radio will stop on frequencies
with clear reception for three seconds before continuing
to the next higher frequency.
Press the SEEK/SCAN button once to stop scanning and
select a frequency.
If no frequency is selected. the radio will return to the
frequency that was displayed when the scan was started.
LOWER
FREQUENCIES HIGHER
FREQUENCIES
PRESS AND HOLD TO SCROLL
THROUGH FREQUENCIES
Fig. 10
SEEK/SCAN
PRESS TO SEEK;
HOLD TWO SECONDS TO SCAN
FREQUENCY
DISPLAY
Fig. 8
MODE DISPLAY
(AM IS SHOWN)
15
Fig. 11
OPERATION
DIRECT TUNE
See Figure 11.
You can select a desired AM, FM or RACE frequency by
pressing the numbered buttons on the keypad to the right
of the LCD.
Press the Direct Tune button.
Enter the desired frequency, using the numbered buttons.
You do not have to enter the decimal point. It is entered
automatically.
NOTE: To delete miskeyed numbers one at a time, press
the Backspace/Clear button for each number you wish
to delete. Key in the desired numbers.
In two seconds, the radio will tune to the entered
frequency.
NOTE: If an incomplete or partial frequency, or one that
does not exist is entered, the radio will return to the last
valid frequency tuned.
See “RACE SPECIFIC FEATURES” later in this manual
for additional Direct Tune information when in RACE
mode.
STORING A PRESET IN MEMORY
See Figure 12.
The memory feature saves up to ten frequencies as presets
in the radio’s memory. You can save up to ten modes each
for FM, AM and RACE modes.
To store a frequency in memory:
Tune to the frequency you want to save.
Press and hold any number on the keypad for three
seconds.
The memory location will appear on the display under
MEMORY. If the “0” key is used to store a frequency, the
number “10” will be displayed under MEMORY.
NOTE: Choosing a memory location where a frequency is
already saved will change the preset to the new frequency.
To recall a preset frequency:
Press the numbered button corresponding to the memory
location number of the saved frequency.
To exit a preset channel and return to Manual Tuning,
push the “Up” or “Down” arrows or the “SEEK/SCAN”
Control.
To clear a preset frequency (RACE MODE only):
Press and hold the Backspace/Clear button for three
seconds to clear a preset from memory.
PRESS KEYPAD NUMBERS TO DIRECT TUNE
HOLD ANY NUMBER (0-9) FOR THREE SECONDS TO ADD A
FREQUENCY TO MEMORY
MEMORY LOCATION
PRESET NUMBER
H
M
H
M
Fig. 12
16
Fig. 13
OPERATION
STEREO/MONO
See Figure 13.
Press the STEREO/MONO button located above the LCD
display to select between stereo mode or mono mode.
This control functions in FM mode only. ST will be displayed
when the radio is in stereo mode and only if the selected FM
station is broadcasting in FM stereo.
MON will appear when the radio is in mono mode.
BASS BOOST
See Figure 14.
Press the BB/SKIP button located above the LCD display
to increase the bass. The bass level can be turned off or
increased by three levels. The bass level will appear on the
right side of the LCD display.
NOTE: The Bass Boost function cannot be used when the
radio is in RACE mode.
Bass Boost is turned off when the button is pressed a fourth
time.
SETTING THE CLOCK
See Figure 15.
The time appears on the LCD display when the radio is on,
or when the radio is off and connected to a power source.
The clock is set using the two small buttons located to the
right of the LCD display.
Use a pointed object (such as an opened paper clip) to
press the H button to set the hour and the M button to set
the minute. Press the button once to move the time foward
one number at a time. Press and hold the button to scroll
quickly through the numbers. When the time is set, the colon
( : ) will blink on and off.
NOTE: This is a 12-hour clock without AM/PM
designated.
STEREO MODE
(FM ONLY)
BASS
BOOST
Fig. 14
Fig. 15
MINUTE (M)
HOUR (H)
17
OPERATION
RACE SPECIFIC FEATURES
The RACE scanner will receive racing transmissions only
when it is in close proximity (within ½ mile) of an active race.
Occasional “blips” may also be received from other devices
that may share the same frequency band.
BEFORE THE RACE
Each driver’s team has multiple frequencies available for
use during a race. The actual frequency they choose to use
can vary.
Before you attend a race, check the internet for frequency
changes and updates for that race’s location. You can then
preset up to ten desired frequencies before you arrive at
the track.
AT THE TRACK
When you arrive at the track, you can get an actual listing
of the frequencies each driver will use for that race. These
listings are usually available at the race facility. These lists
are helpful for checking your preset frequencies against the
ones the team has chosen for that day’s race.
RACE SPECIFIC FEATURES
When RACE mode is selected, the radio will immediately
begin to scan all available race frequencies and the display
will show channels progressing.
NOTE: If channels do not appear to be progressing in the dis-
play, adjust the SQUELCH control as shown in Figure 21.
The scanner will stop on each audible frequency before
continuing the scan.
Tuning and the Direct Tune feature work the same as in
other modes.
NOTE: To return to NORMAL SCAN MODE from Manual
Tuning, briefly push the Backspace/Clear button.
Memory and preset features work the same as in other
modes. See STORING A PRESET IN MEMORY earlier in
this manual.
NORMAL SCAN AND PRESET SCAN MODES
See Figure 16.
With the SQUELCH properly adjusted, the scanner runs
through programmed channels until it finds an active fre-
quency, then stops on that frequency and remains tuned to
it until the transmission ends. The scanning cycle then starts
again until it finds another transmission.
NORMAL SCAN mode is the default mode when RACE
mode is selected. All channels are scanned.
PRESET SCAN mode will scan only the preset channels
stored in the memory by the user. Up to 10 channels may
be stored in memory. The PRESET locations will appear in
the display as they are scanned.
Use the SEEK/SCAN button to toggle between normal and
preset scan modes.
Fig. 17
RACE MODE: NORMAL SCAN (DEFAULT) MODE
SCANS ALL AvAILABLE FREQUENCIES
SEEK/SCAN TOGGLES BETWEEN NORMAL
AND PRESET SCAN MODES
RACE MODE: PRESET SCAN MODE
SCANS ONLY THE 10 PRESET CHANNELS STORED IN MEMORY
Fig. 16
PRESET SCAN MODE
See Figures 17.
Use the SEEK/SCAN button to scan only the preset
race frequencies stored in the radio’s memory, up to 10
channels.
Select RACE mode.
Press the SEEK/SCAN button located below the LCD
display to scan preset frequencies. The display will show
a number under PRESET, and scan through only preset
channels (up to 10).
Press the SEEK/SCAN button again to scan all
frequencies in the race band (NORMAL SCAN MODE).
NOTE: If no preset race frequencies have been stored in
memory, the radio will continue to scan all frequencies in
the race band.
18
DIRECT TUNING A RACE FREQUENCY
(5 DIGITS OF THE 7-DIGIT FREQUENCY ENTERED)
OPERATION
Fig. 18
TO CLEAR A PRESET FREQUENCY:
PRESS AND HOLD BACKSPACE/CLEAR FOR 3 SECONDS
Fig. 19
DISPLAY SHOWS AN EXAMPLE OF PRESET SCAN MODE
CLEARING RACE PRESETS
See Figure 18.
To clear a preset RACE channel from memory:
With RACE mode selected, press the keypad button for
the memory location you wish to clear.
Press and hold the Backspace/Clear button for three
seconds.
After three seconds, the frequency will be replaced by
all dashes, indicating that the preset has been cleared.
The dashes will be displayed for one second, then the
scanner will return to normal scan mode.
DIRECT TUNE
See Figure 19.
With Direct Tune in RACE mode, you can select and monitor
single channels.
Press Direct Tune on the keypad to the right of the
LCD.
Enter the desired seven-digit frequency, using the
numbers on the keypad. Seven digits must be entered.
The scanner will not tune until all dashes are filled.
In RACE mode, the first digit entered must be the number
“4”, or the entered frequency will not be accepted.
NOTE: If an incomplete or partial frequency, or one that
does not exist is entered, the radio will return to scan
mode after ten seconds.
After a station is keyed there is a two-second delay.
The scanner will then switch to and monitor only
that frequency. The displayed frequency can then be
monitored exclusively, blocking all other transmissions
or added to the memory as a preset.
NOTE: To add a preset frequency, tune to the desired
frequency, select any numbered button on the keypad,
and hold for three seconds.
To switch back to normal scan mode from single-channel
monitoring, press and release the Backspace/Clear
button.
DISPLAY SHOWS AN EXAMPLE OF PRESET CLEARED
19
BB/SKIP:
HOLD FOR THREE SECONDS
TO SKIP A FREQUENCY
OPERATION
SKIPPING FREQUENCIES AND PRESETS
See Figure 20.
The skip feature can be used to skip up to five preset race
frequencies (PRESET SCAN MODE) or up to twenty race
frequencies when scanning the entire race band (NORMAL
SCAN MODE).
To skip any desired frequency:
Tune to the frequency you want to skip.
Press and hold the BB/SKIP button located above the
display for three seconds. SKIP will then appear on the
LCD display.
To skip a preset frequency:
Select the frequency you want to skip by pressing its
memory location number on the keypad.
Press and hold the BB/SKIP button located above the
display for three seconds. SKIP will then appear on
the LCD display, and the frequency will be scanned
normally.
To restore a skipped frequency:
Tune to or select the skipped frequency you want to
restore.
Press and hold the BB/SKIP button located above the
display for three seconds. SKIP will then be removed from
the LCD display.
To clear the SKIP from all race channels at once, press and
hold the Backspace/Clear button for ten seconds.
This does not remove the SKIPs from any preset scan mode
channels. SKIPs for presets must be cleared manually.
SQUELCH CONTROL
See Figure 21.
You can use the SQUELCH control dial to tune to stronger
signals without interference or static.
To set SQUELCH:
Rotate the dial fully counterclockwise and adjust the
volume to an audible level. A hissing static sound will be
heard.
Slowly rotate the dial clockwise until the hissing static
sound stops.
The squelch is now properly set.
To allow all signals to be heard:
Rotate the dial counterclockwise to allow multiple signals
to be heard, including signals with lower strength.
NOTE: Rotating the SQUELCH control fully counter-
clockwise will allow the unit to lock on to the nearest
channel (next higher frequency) in the scan progression,
and the progression of channels displayed will virtually
STOP. Scanning will resume with further increases of the
SQUELCH control.
Fig. 21
ROTATE CLOCKWISE TO DECREASE GAIN AND
FILTER STATIC
Fig. 20
SKIPPED DIRECT TUNE
FREQUENCY
SKIPPED PRESET FREQUENCY
20
OPERATION
USING AN iPod WITH THE JOB-SITE RADIO/
RACE SCANNER
See Figures 22 - 24.
FOR DOCKABLE iPods (with 30-pin connector):
Select AUX 1 MODE.
Open the drop-down compartment door by pulling up on
the latch handle.
Orient the iPod face up as shown and slide the unit under
the retainer strap.
Make sure that the 30-pin connector on the iPod is aligned
with the 30 pin connector in the door and that the iPod is
pushed down completely to ensure proper docking.
The iPod must be ON and in PLAY mode for sound to be
heard through the speakers.
The iPod will recharge while playing. The iPod will
recharge when docked, even if the radio power is OFF.
All iPod controls can be used normally while the unit
is docked, with the exception of the volume. Volume
is controlled through the volume control knob on the
radio.
Turning the radio OFF while the iPod is docked will NOT
turn the iPod OFF.
To remove the iPod from the dock, simply pull upward to
disconnect.
To protect the iPod from environmental hazards such as
dust, moisture, etc., the drop-down compartment door
must be closed and latched.
For complete operating instructions for the iPod, always
refer to the manual that was included with your iPod
model.
Fig. 22
Fig. 23
LCD DISPLAYS
AUX 1 MODE
iPod
30-PIN
CONNECTORS
RETAINER
STRAP
21
OPERATION
FOR NON-DOCKING iPods, OTHER MP3 PLAYERS,
AND CD PLAYERS:
Select AUX 2 MODE.
Open the drop-down compartment door by pulling up on
the latch handle.
Make sure the iPod/MP3 player will fit inside the
compartment provided.
NOTE: CD players will not fit.
The retainer strap may be used to secure the iPod/MP3
player into position.
CD players can simply be placed on the foam padding on
the inside of the compartment door. The compartment
door cannot be closed when a CD player is connected.
Connect one end of a 3.5 mm audio patch cord (maximum
8 in. long) to the iPod/MP3/CD player.
Connect the other end of the 3.5 mm patch cord to the
AUX 2 jack provided.
Make sure that the audio patch cable is positioned so
that it is not pinched if the door is closed.
The iPod/MP3/CD player must be ON and in PLAY mode
for sound to be heard through the speakers.
All iPod/MP3/CD player controls can be used normally
while connected to radio.
NOTE: Volume for any device connected through the
AUX 2 jack is adjusted using the volume control for that
device.
Turning the radio OFF will NOT turn the iPod/MP3 player
OFF.
To protect the iPod/MP3 player from environmental
hazards such as dust, moisture, etc., the drop-down
compartment door must be closed and latched.
The AUX 2 jack DOES NOT provide charging function.
For complete operating instructions for all iPod, other
MP3 players, and CD players, always refer to the manual
that was included with your model.
Most CD players are too large to fit inside the internal
compartment. To use these devices, open the drop-down
compartment door to access the AUX 2 input jack, and
connect the device as described above. Turn on the CD
player and adjust the volume to the desired level.
Fig. 24
iPod OR OTHER
MP3 PLAYER
3.5 mm AUDIO
PATCH CABLE
(INCLUDED)
LCD DISPLAYS
AUX 2 MODE
RETAINER
STRAP
22
MAINTENANCE
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING:
To avoid serious personal injury, always remove
the battery pack from the product when cleaning
or performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a RIDGID authorized service center.
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries properly.
This product uses lithium-ion or nickel-
cadmium batteries. Local, state or federal
laws may prohibit disposal of batteries in
ordinary trash.
Consult your local waste authority for
information regarding available recycling
and/or disposal options.
WARNING:
Upon removal, cover the battery pack’s terminals
with heavy-duty adhesive tape. Do not attempt to
destroy or disassemble battery pack or remove
any of its components. Lithium-ion and nickel-
cadmium batteries must be recycled or disposed
of properly. Also, never touch both terminals with
metal objects and/or body parts as short circuit
may result. Keep away from children. Failure to
comply with these warnings could result in fire
and/or serious injury.
BATTERIES
This product will accept 24 V and 18 V lithium-ion batteries or
18 V, 14.4 V, and 12 V nickel-cadmium batteries. Length of
service from each charging will depend on the type of work
you are doing.
The batteries for this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
To obtain the longest possible battery life, we suggest the
following:
For lithium-ion batteries:
Remove the battery pack from the charger once it is fully
charged and ready for use.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F and away from moisture.
Store battery packs in a 30%-50% charged condition.
Every six months of storage, charge the pack as
normal.
For nickel-cadmium batteries:
Remove the battery pack from the charger once it is fully
charged and ready for use.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F.
Store battery packs in a “discharged” condition.
Li - Ion
23
TRACKSIDE PLANNER
Use this chart to record the drivers, car numbers, and frequencies you wish to tune in to or save in memory as a preset
during a race and take it along with you.
RACE LOCATION/DATE:
Driver/Car No. Frequency Preset
RACE LOCATION/DATE:
Driver/Car No. Frequency Preset
24
TRACKSIDE PLANNER
RACE LOCATION/DATE:
Driver/Car No. Frequency Preset
RACE LOCATION/DATE:
Driver/Car No. Frequency Preset
25
WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers de-
fects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE OF
ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY
STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warran-
ties, including warranties of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE, are disclaimed. Any implied
warranties, including warranties of merchantability or fitness
for a particular purpose, that cannot be disclaimed under
state law are limited to three years from the date of purchase.
One World Technologies, Inc. and RIDGID, Inc. are not
responsible for direct, indirect, incidental or consequential
damages. Some states do not allow limitations on how long
an implied warranty lasts and/or do not allow the exclusion
or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights
which vary from state to state.
26
987000-110
03-19-08 (REV:03)
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
online at www.ridgid.com.
The model number of this product is found on a plate attached to the motor hous-
ing. Please record the serial number in the space provided below. When ordering
repair parts, always give the following information:
Model No.
Serial No.
R8408
OPERATOR’S MANUAL
JOB-SITE RADIO/RACE SCANNER
R8408
