Contents
- 1. 5LP1Y8_User Manual_REV1
- 2. 5LP1Y8_User Manual
5LP1Y8_User Manual_REV1
Beams
Spotlight
02_Spotlight_MANUAL.indd 1 9/28/18 4:19 PM
108mm
90mm
1. Set up your Spotlight.
Download the Ring app.
The app walks you through setting up and
managing your Spotlight.
Search for “Ring” in one of these app
stores, or visit: ring.com/app
Set up your Ring Beams Bridge.
The Bridge connects your Ring Beams
lights to the rest of your Ring system.
To set up your Bridge, follow the
instructions in the Ring app or Bridge
user manual.
Download from
Windows Store
If you do not own a Bridge, don’t
worry. Your Spotlight will work
fine, but you won’t be able to
control it in the app.
32
02_Spotlight_MANUAL.indd 3 9/28/18 4:19 PM
Twist and pull off
the front of the light,
then press the side
buttons on the battery
compartment to open.
Insert four D-Cell batteries,
then slide the battery cover
back onto your Spotlight.
Beams
Alarm
Doorbells
Security Cams
Chimes
Set up your
Spotlight in the
Ring app.
In the app, tap
Set Up a Device.
When prompted,
select Beams and
follow the in-app
instructions.
Insert the batteries.
54
02_Spotlight_MANUAL.indd 5 9/28/18 4:19 PM
Hold the base
against the surface
and drive the three
mounting screws.
Loosen the locking
screw on the base
and remove the base
from your Spotlight.
Insert your Spotlight
into the base at your
chosen angle and
tighten the screw.
Use the base as a
template to mark the
screw holes.
2. Install your Spotlight.
Your Spotlight detects motion
best when mounted 8-12 feet
above the ground.
Loosen the side
screw on your
Spotlight, rotate to
desired angle, and
tighten the screw.
76
02_Spotlight_MANUAL.indd 7 9/28/18 4:19 PM
For additional help, visit: ring.com/help
Or give us a call…
US 1 800 656 1918
Canada 1 855 300 7289
Worldwide +1 310 929 7085
For a list of all our customer support
numbers, visit: ring.com/callus
To review your warranty coverage, please visit www.ring.com/warranty.
Patents: www.ring.com/patents
© 2018 Ring LLC or its affiliates.
RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates.
Last updated: 09/28/18
02_Spotlight_MANUAL.indd 8 9/28/18 4:19 PM
Warnings
This device complies with part 15 of the FCC Rules and
Industry Canada licence-exempt RSS standard(s). Opera-
tion is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Caution: Any changes or modifications to this device not
explicitly approved by manufacturer could void your
authority to operate this equipment.
MPE Reminding
To satisfy FCC / IC RF exposure requirements, a separation
distance of 20 cm or more should be maintained between
the antenna of this device and persons during device
operation.
To ensure compliance, operations at closer than this
distance is not recommended.
Les antennes installées doivent être situées de facon à ce
que la population ne puisse y être exposée à une distance
de moin de 20 cm. Installer les antennes de facon à ce que
le personnel ne puisse approcher à 20 cm ou moins de la
position centrale de l’ antenne.
La FCC des éltats-unis stipule que cet appareil doit être en
tout temps éloigné d’au moins 20 cm des personnes
pendant son functionnement.
This device complies with part 15 of the FCC Rules and
Industry Canada licence-exempt RSS standard(s). Opera-
tion is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Caution: Any changes or modifications to this device not
explicitly approved by manufacturer could void your
authority to operate this equipment.
MPE Reminding
To satisfy FCC / IC RF exposure requirements, a separation
distance of 20 cm or more should be maintained between
the antenna of this device and persons during device
operation.
To ensure compliance, operations at closer than this
distance is not recommended.
Les antennes installées doivent être situées de facon à ce
que la population ne puisse y être exposée à une distance
de moin de 20 cm. Installer les antennes de facon à ce que
le personnel ne puisse approcher à 20 cm ou moins de la
position centrale de l’ antenne.
La FCC des éltats-unis stipule que cet appareil doit être en
tout temps éloigné d’au moins 20 cm des personnes
pendant son functionnement.