Risco RWX95CM915 eyeWAVE Wireless PIR Camera, eyeWAVE Wireless PIR Pet Camera User Manual 5IN2581 2W WL PIR CAM Installer

Download:
Mirror Download [FCC.gov]
Document ID	3086324
Application ID	4dNWIfudeUe9BcOGPa7JWA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.69kB (371145 bits)
Date Submitted	2016-08-03 00:00:00
Date Available	2016-08-07 00:00:00
Creation Date	2016-07-11 14:40:18
Producing Software	GPL Ghostscript 9.06
Document Lastmod	2016-07-11 14:40:18
Document Title	Microsoft Word - 5IN2581 2W WL PIR CAM Installer
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Motti_B

eyeWAVE™ Wireless PIR
Camera
Model: RWX95CM/RWX95CMP
EN
Installation instructions
Send a signal transmission from the detector by pressing the tamper
button for at least 2 seconds; the control panel beeps once to accept
or beeps three times to reject. Once accepted, the system
announces the device type and its zone (for example, “Detector,
zone 1”).
When the detectors have been enrolled, short-press the control
panel button
to exit Learn mode; the unit beeps once and the
LEDs stop flashing.
Note: For future use, it is recommended to write down the detector
description, zone number, and installation location of each allocated
detector.
Step 3: Mounting the Detector
Attach the unit to the surface using the two-sided adhesive tape.
For Pet friendly model:
In order to optimize pet immunity the following guide lines are
recommended:
Mount the detector vertically at right angles to the floor.
Make sure an animal cannot get above height of 1.5m (5') by
climbing on furniture, shelving or stairs.
3 Replacing the Batteries
EN
1 General Description
The eyeWAVE™ Wireless PIR Camera
Detector is a battery powered PIR detector that includes an
integrated camera for visual verification and is compatible with
RISCO security systems.
2 Installation
Step 1: Preliminary Considerations
Select the mounting location for best coverage of the area that is to
be protected (see Coverage Patterns).
Step 2: Quick Device Allocation at the Control
Panel
The detector is automatically programmed to your control panel
during the on-line installation wizard setup. If you later purchase an
extra detector you can enroll it as follows:
To quickly allocate the detector at the control panel:
If the control panel is not already in Learn mode, press the
button on the control panel for 5 seconds; the unit beeps once
as it enters Learn mode (all the LEDs also light up, one after the
other).
Remove the plastic wrapping from the batteries before installation
and make sure the cover is removed so the internal tamper switch is
accessible.
Remove the battery’s red strip to activate the battery.
CAUTION – Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to local regulations
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from
defects in materials and workmanship under normal use for 24 months from the date of
production. Because Seller does not install or connect the product and because the product may
be used in conjunction with products not manufactured by the Seller, Seller can not guarantee
the performance of the security system which uses this product. Sellers' obligation and liability
under this warranty is expressly limited to repairing and replacing, at Sellers option, within a
reasonable time after the date of delivery, any product not meeting the specifications. Seller
makes no other warranty, expressed or implied, and makes no warranty of merchantability or of
fitness for any particular purpose. In no case shall seller be liable for any consequential or
incidental damages for breach of this or any other warranty, expressed or implied, or upon any
other basis of liability whatsoever. Sellers obligation under this warranty shall not include any
transportation charges or costs of installation or any liability for direct, indirect, or not be
compromised or circumvented; that the product will prevent any persona; injury or property loss
by intruder, robbery, fire or otherwise; or that the product will in all cases provide adequate
warning or protection. Buyer understands that a properly installed and maintained alarm may
only reduce the risk of intruder, robbery or fire without warning, but is not insurance or a guaranty
that such will not occur or that there will be no personal injury or property loss as a result.
Consequently seller shall have no liability for any personal injury, property damage or loss based
on a claim that the product fails to give warning. However, if seller is held liable, whether directly
or indirectly, for any loss or damage arising from under this limited warranty or otherwise,
regardless of cause or origin, sellers maximum liability shall not exceed the purchase price of the
product, which shall be complete and exclusive remedy against seller. No employee or
representative of Seller is authorized to change this warranty in any way or grant any other
warranty.
WARNING: This product should be tested at least once a week.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to local regulations.
FCC ID: JE4RWX95CM915
4 Technical Specifications
Electrical
Battery Type:
Battery Life:
Current
Consumption:
Supervision
Transmission:
RF transmitting
frequencies:
Optical
Filtering:
Pet friendly:
Physical
Size:
Weight:
Environmental
Operating
Temperature:
Storage
Temperature:
Camera
Type:
Lux:
View Angle:
2 x CR 123, 3V Lithium Battery
2 batteries – 3 year typical lifetime
58 µA standby;
200 mA max. peak at capture with flash
0-255 minutes
915 MHz,916Mhz
White Light Protection
Up to a 36 kg (80lb) animal (pet model)
132 x 67,5 x 56 mm (5.1 x 2.6 x 2.2 in)
169 grams (5.96 oz.)
-10°C a 55°C (14°F a 140°F)
-20°C a 60°C (-4°F a 140°F)
CMOS digital image sensor
0 Lux (total darkness)
H 90° V 71°
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications to this equipment which are not expressly approved by
the party responsible for compliance (RISCO Group's.) could void the user's
authority to operate the equipment.
FCC Note
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on to a different circuit from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
© RISCO Group 07/16
5IN2581
Preliminary Considerations
Do not install
near windows
Do not install near vents
(air, heat, or AC)
Do not install
near ceiling fans
PIR Coverage Patterns
PIR Model
ft. m
10 3
ft m
10 3
3 4 5 6 7 8 9 10 11 12 13 14 15 m
10 15 20 25
30 35 40 45
50 ft
Side View
Figure 1
Ok for sites with small pets
Top View
PIR Pet - SIDE VIEW
10m
Figure 2
Figure 3
90°
3 4 5
10 15
6 7 8
20 25
9 10 11 12 m
30 35 40 ft
70°
Do not install in
direct sunlight
Camera FOV
Pet Friendly Model
PIR - SIDE VIEW
Do not install in
extreme temperatures
10
Do not install
outside
D = 2,4 m
Figure 5
Figure 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:bdae2084-49b7-11e6-0000-fd0f6f90caba
Producer                        : GPL Ghostscript 9.06
Modify Date                     : 2016:07:11 14:40:18+03:00
Create Date                     : 2016:07:11 14:40:18+03:00
Creator Tool                    : PScript5.dll Version 5.2.2
Document ID                     : uuid:bdae2084-49b7-11e6-0000-fd0f6f90caba
Format                          : application/pdf
Title                           : Microsoft Word - 5IN2581 2W WL PIR CAM Installer
Creator                         : Motti_B
Author                          : Motti_B

EXIF Metadata provided by EXIF.tools