Risco STAMP433 433 MHz RF Module User Manual Manual 433Mhz

Download:
Mirror Download [FCC.gov]
Document ID	2283320
Application ID	w6Bjf8leJdeDfp9l2gKK+Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.05kB (375592 bits)
Date Submitted	2014-06-02 00:00:00
Date Available	2014-06-02 00:00:00
Creation Date	2014-06-01 16:41:28
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2014-06-01 16:41:28
Document Title	Microsoft Word - Manual_433Mhz
Document Creator	PScript5.dll Version 5.2.2
Document Author:	motti_b

Risco Group Modular
Certification
Instructions to OEM
P/N Number: RWTRSS10433B-40
FCC ID: JE4STAMP433
1. Revision History
Revision
3 April 2014
1 June 2014
Revision Description of Changes
Initial Release
Modification
Page 1 of 5
© 2014 by Risco Group Ltd. All rights reserved.
2. Introduction
This document describes mandatory steps required by the OEM
Integrator when assembling the Stamp to the unit.
This document lists the mandatory responsibilities and actions of the OEM
integrator.
Failure to comply with all requirements and conditions in this document may
result in non compliance of the device with FCC rules and invalidate the RISCO
Group FCC certification for the Stamp.
3. Overview
The RWTRSS10433B-40 is a "Stamp" transmits in 433.92 MHz. Is an add-in unit
that can be incorporated into security alarm systems. The "Stamp" offers
connectivity to or from the main panel of a security system.
Pic 1
Page 2 of 5
© 2014 by Risco Group Ltd. All rights reserved.
4. Allowed Antennas to be used
Helical HQ P/N: ANT434-CHETH-R
Frequency: 433.92 MHz Gain: Max +3dbi
Soldered to PCB, resists soldering of 260deg +/-5second
Material: Comply with Directive 2002/95/EC Restriction of Hazardous substances, RoHS
Directive, HQ, Beryllium Copper, wire diameter 0.9 mm, tolerance +/- 0.07 mm
Heat Treating material to procure PIM ≤ -138dBc @ Standard Installation
Platting: Tin plating per ASTM–B-545, 5 microns followed by Nickel-plating 5 microns
per MILC-26074. RoHS Compliance.
5. Installation instruction
Assemble the Stamp, pay attention to polarity (see Pic 2).
Pic 2
Antenna
Coupling
Capacitor
220pF
Stamp
RWTRSS1433B-40
Power
Page 3 of 5
© 2014 by Risco Group Ltd. All rights reserved.
6. FCC statement
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with FCC regulations, shielded cables
must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio
and TV reception. The user is cautioned that changes and modifications
made to the equipment without the approval of manufacturer could void
the user's authority to operate this equipment.
Contains Transmitter Module FCC ID: JE4STAMP433
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including Interference
that may cause undesired operation.
Page 4 of 5
© 2014 by Risco Group Ltd. All rights reserved.
7. OEM instructions
1. The module is limited to OEM installation only.
2. The OEM integrator is responsible for that the end-user has no manual
instructions to remove or install the module.
3. The module is limited to installation in mobile or fixed applications,
according to part 2.1091(b).
4. Separate approval is required for all other operating configurations,
including portable configurations with respect to part 2.1093 and different
antenna configurations.
5. Labeling instructions of finished products must contain the following –
contains module FCC ID: JE4STAMP433
The OEM/ integrator must include the following instructions/statements in
the host user’s manual (i.e. end product).
1. Statement is required per FCC part 15.19 and 15.21.
2. End users must be provided with transmitters/antenna installation
requirement and operating conditions for satisfactory RF exposure
compliance:
• A separate section should clearly state “FCC RF exposure
requirements”
• Required operations conditions for end users
• Antenna /or transmitter installation requirement, where
relevant
Page 5 of 5
© 2014 by Risco Group Ltd. All rights reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 5
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2014:06:01 16:41:28
Modify Date                     : 2014:06:01 16:41:28
Title                           : Microsoft Word - Manual_433Mhz
Creator                         : PScript5.dll Version 5.2.2
Author                          : motti_b

EXIF Metadata provided by EXIF.tools