Risco STAMP915-916 915MHz/916MHz RF module User Manual Users manual

Risco Ltd. 915MHz/916MHz RF module Users manual

Users manual

Download: Risco STAMP915-916 915MHz/916MHz RF module User Manual Users manual
Mirror Download [FCC.gov]Risco STAMP915-916 915MHz/916MHz RF module User Manual Users manual
Document ID3157409
Application IDA0smnYiO6TVUWHe74pRF9g==
Document DescriptionUsers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize32.51kB (406419 bits)
Date Submitted2016-10-07 00:00:00
Date Available2016-10-09 00:00:00
Creation Date2016-09-28 15:12:34
Producing SoftwareMicrosoft® Word 2016
Document Lastmod2016-09-28 15:12:34
Document TitleUsers manual
Document CreatorMicrosoft® Word 2016
Document Author: motti_b

Risco Group Modular
Certification
Instructions to OEM
P/N Number: RWDTR9S916VA-40
(consisting of RWTRSS10915A-40 & RWTRSS10916A-40)
FCC ID: JE4STAMP915-916
28 September 2016
Revision
19 July 2016
28 September 2016
Revision Description of Changes
Initial Release
Add warning text
Page 1 of 3
FCC statement
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with FCC regulations, shielded cables
must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio
and TV reception. The user is cautioned that changes and modifications
made to the equipment without the approval of manufacturer could void
the user's authority to operate this equipment.
Contains Transmitter Module FCC ID: JE4STAMP915-916
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including Interference
that may cause undesired operation.
Page 2 of 3
OEM instructions
1. The module is limited to OEM installation only.
2. The OEM integrator is responsible for that the end-user has no manual
instructions to remove or install the module.
3. The module is limited to installation in mobile or fixed applications,
according to part 2.1091(b).
4. Separate approval is required for all other operating configurations,
including portable configurations with respect to part 2.1093 and different
antenna configurations.
5. Labeling instructions of finished products must contain the following –
contains module FCC ID: JE4STAMP915-916
The OEM/ integrator must include the following instructions/statements in
the host user’s manual (i.e. end product).
1. Statement is required per FCC part 15.19 and 15.21.
2. End users must be provided with transmitters/antenna installation
requirement and operating conditions for satisfactory RF exposure
compliance:
 A separate section should clearly state “FCC RF exposure
requirements”
 Required operations conditions for end users
 Antenna /or transmitter installation requirement, where
relevant
WARNING! Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Page 3 of 3

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Language                        : he-IL
Tagged PDF                      : Yes
Author                          : motti_b
Creator                         : Microsoft® Word 2016
Create Date                     : 2016:09:28 15:12:34+03:00
Modify Date                     : 2016:09:28 15:12:34+03:00
Producer                        : Microsoft® Word 2016
EXIF Metadata provided by EXIF.tools
FCC ID Filing: JE4STAMP915-916

Navigation menu