Ritetemp 6022 Owner S Manual 8022 6022_operation_guide 2014-07-06
: Ritetemp Ritetemp-6022-Owner-S-Manual ritetemp-6022-owner-s-manual ritetemp pdf
Open the PDF directly: View PDF .Page Count: 9
Operation Guide 6022
Statement of use: The
6022 can be used with millivolt, 24V single and
2-stage conventional
systems, gas/oil/electric
heat, 1-stage heat
pumps, 2 -stage heat
pumps, zoned hot water
(2 or 3 wire), zoned
forced air, single and 2stage cooling, and hybrid
systems.
Control Panel
Heat/Cool
Mode Switch
Reset
button
Fan
Switch
TEMP UP
button
Target
Temp
TEMP DOWN
button
TIME SET
TARGET TEMP
TIME SLOT
HEAT
Time
PROG2
SET CLOCK
EPA
PROGRAM
COPY HOLD
ER
REVIEW FILT
Battery
Compartment
ENGLISH
PG
Set Clock
2
5
7
4
6
8
123
Set day of the week • Press SET CLOCK once
to set the day of the week.
The day of the week display
flashes. (Initially SU for Sunday)
• Press
TIME
to select the day.
Set time of day • Press SET CLOCK again to set the time. The time display will flash.
TIME or TIME>
TIME to set the time. Press and hold to set the time
• Press buttons
to move the set point forward or backward in time.
• Select the next TIME SLOT and program temp and time:
Press NEXT
NEXT>
the display will show DAY. Repeat setting temp and time.
Select the remaining TIME SLOT's, EVEN and NITE. Program their temp and
time info. Repeat the above procedures for each day of the week.
Push DAY>
DAY button to cycle through the days.
To COPY the program of the current day to another day, press COPY
program once. COPY will display on the LCD. The day icon for the source
day will go solid and the day icon for the destination day will flash. Use day
button to select the destination day. Press COPY again to confirm the copy.
If you decide you don't want to copy, press HOME to exit.
PG
5
Program cont.
PROG 2: An alternative program can be used for holidays, shift work, etc.
Access by pushing the PROG 2 button. PROG 2 will then be active until you
shut it off by touching the PROG 2 button again. The main program will then
DAY until PROG 2 is displayed
again be active. To change PROG 2 press DAY
and repeat the programming procedure.
• When finished with your custom program, either wait 60 sec or press HOME
to save and run your program.
To program for COOL, select COOL with the Heat/Cool MODE switch and
repeat the above procedure.
To REVIEW the program you have entered:Press PROGRAM once to enter
programming mode.Then press FILTER/REVIEW once.
PG
6
The display will cycle through the programmed times and temps, showing
each program for 12 seconds. Starting from Sunday; MORN and ending on
Saturday; NITE. The programmed temperature is shown on the left of the
LCD, the programmed time, day and time slot are shown on the right and the
right top of the LCD respectfully.
• Press HOME to leave program REVIEW mode and run the program.
Special Features - Swing
SWING setting determines the temperature difference from ON to OFF that the
6022 will command the HVAC system to run.
• With the MODE switch in HEAT or COOL, press the TIME button.
• The SWING icon is displayed. The current setting of temp swing is shown on the
o
display (default at .5 F).
To change the swing, push TEMP UP or TEMP DOWN buttons. The furnace will
cycle more at the lower numbers as it tries to keep your set point constant.
PG 7
To complete the swing setting, push the HOME button.
Spec. Featr. cont.
Manual
TEMP UP
button
TARGET TEMP
• With the MODE switch in HEAT or COOL, push the TEMP
TEMP +/- buttons to temporarily change the control DOWN
temperature by 1 degree per step. Press and hold for button
faster setting.
• The OVERRIDE icon flashes to shows the displayed
temperature may be different from the programmed setting.
• The OVERRIDE is canceled at the start of the next time period,
or when the MODE switch is moved, or if TEMP HOLD is pressed twice.
PG
8
Temp HOLD
To change and hold the temperature until you return.
• Open the door and push the HOLD button. The HOLD icon comes on.
Push the UP or DOWN arrow buttons to set the hold temperature.
• HOLD is canceled if the MODE switch is moved, or press HOLD again.
Lock
Allows you to lock the 6022 (to prevent any changes in custom settings)
• To enable or disable the program lock, press the following buttons one at
a time,in this sequence.
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.5
Linearized : Yes
Page Count : 9
XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6
About : uuid:5c7df70b-9c5a-495a-8712-9c4ae9ca2369
Modify Date : 2007:01:17 12:08:46-08:00
Create Date : 2007:01:17 12:08:45-08:00
Metadata Date : 2007:01:17 12:08:46-08:00
Document ID : uuid:0693d515-2551-49a6-95bf-593b341ebea1
Format : application/pdf
Creator : Adobe Acrobat 6.0
Producer : Adobe PDF Library 2.0
EXIF Metadata provided by EXIF.tools
.