Ritetemp 8022C Owner S Manual 2014-07-06
: Ritetemp Ritetemp-8022C-Owner-S-Manual ritetemp-8022c-owner-s-manual ritetemp pdf
Open the PDF directly: View PDF .Page Count: 7
Operation 8022C
MP
SET TE
HEAT
F
PM
FAN
OFF
L
COO
ON
AUTO
EAT
H
SET TE
MP
HEAT
F
PM
FAN
OFF
HEA
L
COO
ON
AUTO
T
Customer Support: 888-515-2585 or
Visit our webiste www.ritetemp-thermostats.com
Made In China
401-006
Operation 8022C
TEMP UP Time/ Current Temp AA Battery
Compartment
Display
button
Control Panel
- Cover Closed TIME
SDP
P
TEM
UP
ERY
BATT
E
HOM
SET
TIME
E
OT
SL
E
TIM
TP
NEX
DAY
M
GRA
PRO
TEMP
SET
TIM
CK
CLO
SET
ER
FILT W
IE
REV
LD
P HO
TEM COPY
FAN
ET
RES
Fan
Switch
P
SET TEM
PM
DE
MO
PM
FAN
OFF
COOL
Fan
Switch
Set Temp
TEMP DOWN Display
button
PG
1
Heat/Cool
Mode Switch
ON
AUTO
HEAT
Reset button
N
DOW
Mode
Switch
Statement of use: The GPMG8022c can be used with
most 24 volt gas, oil or electric heating and air conditioning
systems, single-stage heat pumps or gas millivolt heating
systems. It cannot be used with 120 volt heating
systems or multistage heat pumps.
1 Set Clock
Set day of the week Press SET CLOCK once to set the day of the week. The
day of the week display flashes. (Initially SU for Sunday)
Press
TIME
to select the day.
TEMP
UP
Press HOME to store your
BATTERY
settings.
SET CLOCK
PG
2
Set time of day Press SET CLOCK twice to set
the time. The time display will
flash.
Press
TIME to set
the time. Press and hold to set
the time in the fast mode.
Press HOME to store your
settings.
SET TEMP
P2
F
HOME
SDP
TIME SET
TIME SLOT
TIME
DAY
NEXT P
TIME
PROGRAM
TEMP HOLD
COPY
FILTER
REVIEW
RESET
MODE
DOWN
FAN
2 Auto-run
TM
This Thermostat comes preprogrammed with an Energy-Star
approved program. This program is recommended by the EPA for
SET TEMP
energy efficiency.
We strongly recommend that you Auto-Run this
program for one week, and see if it works for you.
If it does not fit your needs you can always input a
custom program.
TM
To Auto-Run the Energy-Star program, select HEAT or COOL with the mode
switch. The unit is now running the Energy-Star program.
TM
The clock and the ambient temperature are displayed on the right.
They alternate every 2 seconds. One of the TIME SLOT icons P1/P2/P3/P4
comes on, this indicates the TIME SLOT active in the Energy-Star program.
Tm
The programmed temperature is shown on the left. For program details refer to
the Energy-Star program chart below.
TM
HEAT
PG
3
All Days
P1
6:00am
70oF
P2
8:00am
62oF
P3
6:00pm
70oF
P4
10:00pm
COOL
All Days
P1
6:00am
78oF
P2
8:00am
85oF
P3
6:00pm
78oF
P4
10:00pm
3 Program
NOTE: 60 Second Rule-During programming, if a button is not
pushed within 60 seconds, the unit will go out of the set mode.
Everything you have input in this programming will automatically be saved.
Select HEAT with the HEAT/Cool MODE switch. SET TEMP
Select the day you want to program: Press the
PROGRAM to enter programming mode. The
PROGRAM FOR icon will come on. The day icon will
show SU (Sunday). Press day
DAY again to advance
the day selection.
Select the TIME SLOT you want to program: To change the TIME SLOT
(P1, P2, P3, P4) press the NEXT
NEXT P button. The display will cycle through the
time periods in sequence. Select P1.
Select the desired temperature for that TIME SLOT : To change the
temperature for that TIME SLOT press the TEMP UP / TEMP DOWN buttons.
Select the time of day you want that TIME SLOT to represent:
To set the time when P1 will begin , press the TIME
buttons to
move the set point forward or backward in time.
PG 4
3 Program cont.
Select the next TIME SLOT and program temp and time:
Press NEXT
NEXT>,P
the display will show P2, for Period 2. Repeat setting temp
and time. Select the remaining TIME SLOT's, P3 and P4. Program their temp
and time info.
DAY
Repeat the above procedures for each day of the week. Push DAY>
button
to cycle through the days.
To COPY the program of the current day to another day, press COPY
program once. COPY will display on the LCD. The day icon for the source
day will go solid and the day icon for the destination day will flash. Use day
DAY
button to select the destination day. Press COPY again to confirm the copy.
If you decide you don't want to copy, press HOME to exit.
To program an alternate or "Special Day" program, that you can access at
DAY until PROGRAM FOR for SDP DAY is displayed.
any time, press PRO
Repeat the procedure above to program temp settings for the Special Day.
5
PG
3 Program cont.
When finished with your custom program, either wait 60 sec or press HOME
to save and run your program.
To program for cooling, select COOL with the Heat/Cool MODE switch and
repeat the above procedure.
To REVIEW the program you have entered:
Press PROGRAM once to enter programming mode.
Then press FILTER/REVIEW once.
The display will cycle through the prgrammed times and temps, showing
each program for 12 seconds. Starting from Sunday; P1 and ending on
Saturday; P4. The programmed temperature is shown on the left of the LCD,
the programmed time, day and time slot are shown on the right and the right
top of the LCD respectfully.
Press HOME to leave program REVIEW mode and run the program.
PG
6
4 Special Features
SDP
The "Special Day Program" can be used when you are unexpectedly home
and need to activate this heat / cooling program just for the day.
With the MODE switch in HEAT or COOL press the SPECIAL DAY button to
activate.
When the SPECIAL DAY Program is active, all other day settings are all
ignored even if the day is matched.
The SPECIAL DAY program will terminate when the mode switch is moved
or if the SPECIAL DAY button is pushed again.
SET TEMP
PG
7
4 Spec. Featr. cont.
Swing
Swing setting determines the temperature difference from
ON to OFF that the thermostat will command the heating/cooling system to run.
With the MODE switch in HEAT or COOL, press the TIME
button.
The SET TEMP SWING icon is displayed. The current setting of temp swing is
shown on the display (default at 3 ).
To change the swing, push TEMP UP or TEMP DOWN buttons. The furnace will
cycle more at the lower numbers as it tries to keep your set point constant.
UP-Arrow
To complete the swing setting, push the HOME button.
button
Manual
With the MODE switch in HEAT or COOL, push the UP or DOWN
arrow buttons to temporarily change the control temperature by 1
degree per step. Press and hold for faster setting.
The OVERRIDE icon comes on which shows the displayed
temperature may be different from the programmed setting.
The OVERRIDE is canceled at the start of the next time period,
or when the MODE switch is moved, or if TEMP HOLD is pressed twice.
DOWN-Arrow
button
PG
8
4 Spec. Featr. cont.
TEMP HOLD
To change and hold the temperature until you return.
Open the door and push the TEMP HOLD button. The HOLD icon comes on.
Push the UP or DOWN arrow buttons to set the hold temperature.
HOLD is canceled if the MODE switch is moved, or press TEMP HOLD again.
Filter
The life of a heater filter varies depending on many factors, furnace run
time, and this will vary from the filter life noted on the filter media.
The 8022C has a feature that keeps track of actual furnace run time and
reminds you to periodically replace your system's air filter.
Press the FILTER button once to review the current filter record.
The FILTER and HR icons come on with accumulated filter hours being displayed.
Press TIME
to clear the record. Press again to recover the previous record.
To see the filter limit setting, press and hold the FILTER button for two seconds.
To change the filter limit hours setting, press TIME
F. or or TIME
B.
Press and
hold for faster setting. The filter limit can be set within 000-500 hours.
To leave the filter display, press HOME or wait 60 seconds.
PG 9
4 Spec. Ftr. cont.
Lock
Allows you to lock the Program (to prevent any changes in custom settings)
To enable or disable the program lock, press the following buttons one at a time,
in this sequence.
TIME then FILTER, then SET CLOCK, and last HOME.
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.4
Linearized : Yes
Create Date : 2004:07:30 17:32:25Z
Modify Date : 2004:08:30 20:04:10-07:00
Page Count : 7
Has XFA : No
Creation Date : 2004:07:30 17:32:25Z
Mod Date : 2004:08:30 20:04:10-07:00
Producer : Acrobat PDF File Format dob for Macintosh
Author : ob
Metadata Date : 2004:08:30 20:04:10-07:00
Creator : ob
EXIF Metadata provided by EXIF.tools
.