Robertshaw Controls d b a Invensys Home Control Systems EMSG-100-CR Wireless Cable Ready Gateway User Manual TD2002

Download:
Mirror Download [FCC.gov]
Document ID	262295
Application ID	WL23YdJJeEywHfpDkrpnXQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.97kB (312139 bits)
Date Submitted	2002-08-08 00:00:00
Date Available	2002-08-08 00:00:00
Creation Date	2002-08-05 18:21:30
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2002-08-05 18:21:30
Document Title	TD2002.fm
Document Creator	AdobePS5.dll Version 5.2.1

EMSG-100-CR
Invensys RF Gateway
General Instructions
Introduction
FIGURE 1.
Invensys RF Gateway
The Invensys RF Gateway is a high performance
wireless broadband server that is a central part of
the Invensys GoodWatts system.
In addition to basic product description, this
document provides specifications and specific
instructions for setup.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Note: To comply with FCC RF exposure requirements in
section 1.1307, a minimum separation distance of 20 cm
(8 inches) is required between the antenna and all
persons.
Inspection
Inspect the product carton for damage. If damaged,
notify carrier immediately. Inspect Invensys RF
Gateway for damage. Return damaged products.
Check that the contents includes all components, as
listed below and shown in FIGURE 2. Invensys RF
Gateway Components:
– Invensys RF Gateway
– Power adapter
Caution: This equipment is authorized for use under the
United States Federal Communication Commission Rules
and Regulations, Code of Federal Regulations Chapter 47
part 15 and must be installed in accordance with the
instructions provided in this document. Failure to install
or operate this equipment as instructed in this document
could void the user’s authority to operate the equipment.
This equipment contains no user serviceable parts. Any
modification or repairs to the internal components or to
the antenna configuration of the equipment without the
express written consent of Invensys Home Control
Systems could void the user's authority to operate the
equipment.
TD2002
COPYRIGHT© 2002 INVENYS HOME CONTROL SYSTEMS
8/5/02
INVENSYS RF GATEWAY
GENERAL INSTRUCTIONS
FIGURE 2.
Invensys RF Gateway Components
Your Invensys RF Gateway package should contain the following items:
Power Adapter
Invensys RF Gateway
Installation
Before you begin installation, please confirm the following system requirements
are met and check that possible conflicting applications are addressed:
Location
The Invensys RF Gateway is an Energy Star compliant low power consumption,
“always-on” server appliance. Proper location and setup of the device is
essential for achieving top performance and longevity. The Invensys RF Gateway
should be situated in a clean, flat, stable, open environment with adequate
ventilation and isolated from any forms of moisture, dust and contaminates.
Placement of the device on or near a desktop or industrial shelving is
recommended, however, placement within a wiring closet or wall mounting
(professional installation recommended) are also viable alternatives.
PRELIMINARY DOCUMENT
TD2002
GENERAL INSTRUCTIONS
LOCATION
Connections
The following section provides instructions for connecting to the Internet and
the procedural steps for applying power to the gateway.
FIGURE 3.
Invensys RF Gateway connections
Direct Cable Outlet
Connection
(EMSG-100-CR)
Power Adapter
DATA PORT
INVENSYS QUALIFIED
TECHNICIAN
1. Refer to FIGURE 3. Invensys RF Gateway connections, and connect your Invensys RF
Gateway to the Direct Cable Outlet Connection, as shown.
2. Plug the supplied power adaptor into the DC connector on the back of the Invensys
RF Gateway and insert the power plug into a wall socket with surge protection.
Note: There is NO power switch located on the Invensys RF Gateway unit. The unit is
“on” when you plug it in to a power outlet. Turning the gateway “off” is controlled via the
gateway software or by unplugging the power adapter.
3. The Invensys RF Gateway will automatically run a 2-3 minute sequential self-test. The
LED light located on the front of the gateway will indicate the status of the process,
starting from a green blinking light through a solid green light if every test passes.
Note: You may see a very subtle orange blinking over the Solid Green light when the
data is processing
4. Follow the LED readouts and proceed accordingly. Refer to TABLE 1. LED indicator
descriptions for a listing of light indications.
8/5/02
PRELIMINARY DOCUMENT
INVENSYS RF GATEWAY
GENERAL INSTRUCTIONS
TABLE 1. LED indicator descriptions
LED Status
Green Blinking (1 blink)
Indication
Process basic hardware testing
Action
Wait for LED status change
Green Blinking (2 blinks)
Process extensive hardware testing
Wait for LED status change
Green Blinking (3 blinks)
Process software testing
Wait for LED status change
Green Blinking (4 blinks)
Indicates Internet (WAN) connection
needs configuration via Invensys RF
Gateway software
Contact Technical Support
Solid Green light
Indicates Internet (WAN) connectivity
is complete
No action necessary
Red Blinking
An internal failure has occurred
Contact technical support
Operation
The Invensys RF Gateway is pre-configured to automatically use the WAN interface for
connecting to the GoodWatts.com server. After a connection is made, the home-specific
information is downloaded into the gateway and the RF device network is started, as
shown in FIGURE 4. GoodWatts RF device network.
FIGURE 4.
GoodWatts RF device network
Thermostat
Gateway
Load
Control Meter
PRELIMINARY DOCUMENT
Meter
TD2002
GENERAL INSTRUCTIONS
8/5/02
OPERATION
PRELIMINARY DOCUMENT
© Invensys 2002
All specifications are nominal and may change as design improvements are introduced. Invensys shall not be liable for damages resulting from misapplication or misuse of its products.
Marks bearing ® and/or ™ are registered trademarks and trademarks of Invensys.
Terms and product names in this document may be trademarks of others.
TD2002
INVENSYS RF GATEWAY
PRINTED IN U.S.A.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:08:05 18:21:30-04:00
Modify Date                     : 2002:08:05 18:21:30-04:00
Creator                         : AdobePS5.dll Version 5.2.1
Page Count                      : 6
Creation Date                   : 2002:08:05 22:21:30Z
Mod Date                        : 2002:08:05 22:21:30Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Metadata Date                   : 2002:08:05 22:21:30Z
Title                           : TD2002.fm

EXIF Metadata provided by EXIF.tools