Rubbermaid Outdoor Storage 5L10 Users Manual Assembly Instructions English

5L10 to the manual 58793155-9e1b-427e-9b0e-54e921acd756

2015-02-06

: Rubbermaid Rubbermaid-Outdoor-Storage-5L10-Users-Manual-525558 rubbermaid-outdoor-storage-5l10-users-manual-525558 rubbermaid pdf

Open the PDF directly: View PDF .
Page Count: 12

Congratulations and thank you for purchasing a Rubbermaid storage building.

BEFORE YOU BEGIN – BUILDING CODES

Be sure to check your local building codes, ordinances and restrictions, and applicable neighborhood governances.

BEFORE YOU BEGIN – SURFACE PREPARATION

To ensure proper assembly and performance your shed needs to be built on a solid, level surface.

A concrete or patio surface, or a treated-wood platform is recommended.

BEFORE YOU BEGIN – LOCATION

When choosing a location in your yard make sure you choose an area with easy access and one that provides

proper drainage for water to run away from the shed location.

BEFORE YOU BEGIN – PREASSEMBLY

Thoroughly review all assembly steps (it is important that

the steps are followed in the correct order). Review the

parts list and make sure that no parts are missing.

IMPORTANT – DO NOT RETURN TO THE STORE

For assistance with your Rubbermaid Storage Building

or for additional product information call our toll-free

Consumer Service number: 1-888-895-2110

M–F: 8:30 a.m. to 5:00 p.m. EST

or visit us online at: www.rubbermaid.com.

Installation Steps:

1. Site Preparation

2. Floor

3. Walls

4. Roof & Doors

5. Finishing

5L10

76 ¾"

27 ½"

55 ¼"

1780068

Note: Be sure to keep this instruction manual and your original store receipt to ensure our Consumer Service

Department can accurately and quickly assist you if necessary.

Description Part Number Assembly Letter Quantity Required Tools

Two Person Assembly

Floor

Front Floor 5L01 A1

Walls

Left Back 5L04 D1

Right Back 5L05 F1

Front Left Side 5L02 G1

Front Right Side 5L03 H1

Wall Connector 5H75 Q5

Doors

Left Door 5L06 / 5L41 L1

Right Door 5L07 / 5L42 K1

Door Handle 5L74 T1

Lock Hasp 5F58 X1

Hardware

#14 x 3/4" Combo Pan Head Screw AA 24*

Accessory Bracket 5H88 4

Roof

Front Roof 5L08 J1

Roof Brace 5L36 RB 1

Safety

Glasses

Phillips Screwdriver

Rubber Mallet

Liquid

Soap

(2) Step Stools/

Stepladders

Drill

Gloves

Utility Knife

1/8" Drill Bit

Phillips Bit

5L10

PREASSEMBLY:

• Review ALL assembly steps before beginning construction.

• Review the parts list and make sure that no parts are missing.

* Extra screws are supplied

76 ¾"

27 ½"

55 ¼"

Qx5

Safety

Glasses

Phillips Screwdriver

Rubber Mallet

Liquid

Soap

(2) Step Stools/

Stepladders

Drill

Gloves

Utility Knife

1/8" Drill Bit

Phillips Bit

NOTE:

• To simplify assembly and to ensure proper engagement of all components,

apply a mild detergent to dovetail and snap ﬁts before assembling.

Build a solid, level surface for the shed foundation. Consult your

local building authority for ordinances, restrictions, or permits

required before building any structure at your home.

Note: Minimum dimensions for foundations shown.

FLOOR PLAN:

Size the construction site to ﬁt the entire ﬂoor.

OPTIONAL STEP:

If desired, recessed anchor locations (5 places)

can be used to anchor the shed ﬂoor to a foundation

after you have constructed one.

55¼"

27½"

1.0 Site Preparation

"18

"24 "24

"~5

"~27-1/2

120.0

"24-7/8

"~55-1/4

"~4-1/2

3-5/8

"3-5/8

ANCHOR

LOCATIONS

Maximum opening

CARE & USE

• Shed can be cleaned with water and mild detergent as

necessary. DO NOT USE ABRASIVE DETERGENTS,

MATERIALS OR CLEANING TOOLS.

• To maximize your shed’s performance, remove

excessive snow and/or leaf accumulation from the roof.

• In the event of severe weather, please disassemble

and store in a secure location.

CAUTIONS

CAUTION: Always use gloves when using a utility knife.

CAUTION: Always use eye protection/safety glasses

during assembly.

CAUTION: When installing screws, do not overtighten.

CAUTION: Drill only through initial panel wall, unless

otherwise indicated.

2.0 Floor Installation

Using a rubber mallet and screwdriver, knock out the

tabs for the door hinge, 2 places on Front Floor (A).

Drill pilot hole through top surface of ﬂoor, 2 places on Front Floor (A).

Using a utility knife, cut the long side of each wall slot

tab and then use a rubber mallet and screwdriver to

knock it out 8 places on Front Floor (A).

CAUTION: Drill through top surface of ﬂoor only!

3.0 Wall Panel G Installation

Using a screwdriver, punch out the screw holes on the

top of Front Left Side (G) 2 places.

Screw Holes

Snap Front Left Side (G) into Front Floor (A).

Hold Front Left Side (G) upright to prevent it from

falling (until Left Back (D) is installed).

ALIGN

click

Drill a pilot hole (using 1/8" drill bit) in front lower corner

at location indicated by screw target.

Note: This pilot hole is to be drilled through both walls.

OVERHEAD VIEW

DETAIL 3-1_B

SCALE 1/1

DETAIL 3-3_E

SCALE 1/1

DETAIL 3-3_B

SCALE 1/1

DETAIL 3-4_B AND 3-5_B

SCALE 1/1

DETAIL 3-6_B AND 3-7_B

SCALE 1/1

3.1 Wall Panel D Installation

Connect Left Back (D) into dovetails of Front Left Side (G).

b. Engage snaps on bottom of Left Back (D) into

Front Floor (A).

Using a screwdriver, punch out the screw holes on the

top of Left Back (D) 4 places.

Screw Holes

HELPFUL HINT: Lubricate dovetails with liquid soap.

click

ALIGN

3.2 Wall Panel H Installation

Using a screwdriver, punch out the screw holes on the

top of Front Right Side (H) 2 places.

Screw Holes

Snap Front Right Side (H) into Front Floor (A).

Hold Front Right Side (H) upright to prevent it from

falling (until Right Back (F) is installed).

Drill a pilot hole (using 1/8" drill bit) in front lower corner

at location indicated by screw target.

Note: This pilot hole is to be drilled through both walls.

ALIGN

click

Connect Right Back (F) onto dovetails of Front Right

Side (H).

Align the lap joint between Left Back (D) and Right Back (F).

b. Engage snaps on bottom of Right Back (F) into

Front Floor (A).

DETAIL 3-1_B

SCALE 1/1

DETAIL 3-3_E

SCALE 1/1

DETAIL 3-3_B

SCALE 1/1

DETAIL 3-4_B AND 3-5_B

SCALE 1/1

DETAIL 3-6_B AND 3-7_B

SCALE 1/1

HELPFUL HINT: Lubricate dovetails with liquid soap.

OVERHEAD

VIEWS

DETAIL 3-1_B

SCALE 1/1

DETAIL 3-3_E

SCALE 1/1

DETAIL 3-3_B

SCALE 1/1

DETAIL 3-4_B AND 3-5_B

SCALE 1/1

DETAIL 3-6_B AND 3-7_B

SCALE 1/1

D F

Align Lap Joints

click

ALIGN

3.3 Wall Panel F Installation

Using a screwdriver, punch out the screw holes on the

top of Right Back (F) 4 places.

Screw Holes

Install Wall Connector (Q) 5 places, connecting Left Back and Right Back Panels (D and F).

Position connectors in slots and slide down to snap in place.

click

OVERHEAD VIEW

D F

Install Wall

Connectors

4.0 Roof Panel J & Door Installation

Install Front Roof (J) onto side sections. Align tongues on top of side walls into grooves in roof.

Ensure Front Roof (J) is positioned against the back wall tongues.

From outside the shed, install one Screw (AA) at each corner.

Hold the edge of the roof down ﬁrmly at the corners while installing each screw.

Install remaining screws into remaining locations of back walls.

c. AA (8)

1. 2.

Helpful Hint: Installation is easier using a magnetic bit or starting

screws with a manual screwdriver to get seated. Pilot holes also

may be drilled using 1/8" bit.

Slightly raise front edge of roof enough to allow positioning of Roof Brace (RB) onto the side walls as shown.

Lower the roof onto the walls and align Roof Brace (RB) into pocket in Front Roof (J).

From inside the shed, install four Screws (AA) into the roof,

two on each side wall.

Note: The screws also have to go through the Roof Brace

(RB) at each end to properly secure the roof!

A second person on the outside of the shed should hold

down the edge of the roof ﬁrmly at each screw location.

Install Left Door (L) and Right Door (K) into hinge openings

of Front Floor (A) and hinge sockets in Front Roof (J).

Note: Only raise front edge of roof enough to install the

door hinge pins.

AA (4)

5.0 Finishing Installation

Install Screws (AA) into 6 locations shown at bottom of wall panels to secure walls to ﬂoor.

a. AA (6)

HELPFUL HINT: Pilot holes may be drilled for the screws.

CAUTION: Do not overtighten screws.

5.1 Door Finishing Installation

Install Lock Hasp (X) into opening on Right Door (K).

a. Install Door Handle (T) onto Left Door (L) using four

Screws (AA).

click

AA (4)

Printed in U.S.A.

2010 Rubbermaid Incorporated,

Huntersville, NC U.S.A. 28078-1801

Customer Service

Toll Free: 1-888-895-2110

M–F 8:30 a.m. to 5:00 p.m. EST

or visit us at www.rubbermaid.com

MAINTENANCE & SAFETY

• Periodically check shed to assure it remains stable and the site remains level.

• In areas of high winds it is recommended to anchor shed to platform or ground

by holes in ﬂoor at designated location and secure with the proper fasteners

(not included).

• Wash shed with garden hose or a mild detergent solution. Using an abrasive

cleaner could damage your shed.

• Hot items such as recently used grills or ﬁre pits should not be stored in the

building.

• Heavy items should not be leaned against the walls, as this may cause distortion.

• Keep doors closed when not in use to prevent wind damage.

• Do not climb onto roof.

• Shed is not designed for habitation.

76 ¾"

27 ½"

55 ¼"

Rubbermaid Outdoor Storage 5L10 Users Manual Assembly Instructions English

5L10 to the manual 58793155-9e1b-427e-9b0e-54e921acd756

Navigation menu

Versions of this User Manual:

Views

Navigation