Ruckus Wireless MF2201 802.11b/g Access Point User Manual User s Guide
Ruckus Wireless, Inc. 802.11b/g Access Point User s Guide
users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 630786 |
| Application ID | vy4b5UtJXZAld2VOuC4zjw== |
| Document Description | users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 210.93kB (2636591 bits) |
| Date Submitted | 2006-02-22 00:00:00 |
| Date Available | 2006-02-21 00:00:00 |
| Creation Date | 2006-01-23 13:22:10 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2006-01-23 13:22:10 |
| Document Title | User’s Guide |
| Document Creator | FrameMaker 7.0 |
| Document Author: | Video54, Inc. |
MF 2201 Gateway MF2201 MetroFlex Wireless Access Gateway User’s Guide Part number: 8000003 December 2005 Copyright © 2005 Ruckus Wireless, Inc. All rights reserved. December 2005. Trademarks Ruckus Wireless, BeamFlex™, MediaFlex™, MediaFlex 2900 Multimedia Access Point, MF 2201 MetroFlex Wireless Access Gateway, MF2900 AP, and MF 2201 Gateway are trademarks of Ruckus Wireless Web Interface All other brand and product names are registered trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, Ruckus Wireless, Inc. reserves the right to make changes to the products described in this document without notice. Ruckus Wireless, Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice The device has met the FCC 15.247 requirement. In order to comply with the FCC RF exposure requirement, the user must keep 20cm away from the antenna. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Information to the user The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. EN 55 022 Declaration of Conformance This is to certify that the MF 2201 MetroFlex Wireless Access Gateway is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22). MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Who Should Use this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What You’ll Find in this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typographic conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Support and Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MetroFlex™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BeamFlex™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 2: Installation and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MF 2201 MetroFlex Wireless Access Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Status Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Placement Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Establishing a good general location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Air Quality Indicator to fine-tune the placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting to the MF 2201 Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manually Configuring an IP Address on Your PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting a PC to the MF 2201 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 12 12 13 14 15 15 15 15 15 16 17 Chapter 3: Using the Ruckus Wireless Web Interface . . . . . . . . . . . . . . . . . . . . 19 Wireless Settings Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MF 2201 Gateway Settings Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ruckus Wireless Web Interface Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Common Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Quality Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the MF 2201 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customizing the System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the Wireless Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Advanced Wireless Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring WEP Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring WPA PSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing Wireless Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 21 22 22 22 24 24 25 26 28 30 33 34 34 35 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide Viewing Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing LAN Interface Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing Wireless Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing Remote AP Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Performing a Web Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TFTP or FTP Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rebooting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Taking a System Support Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 37 38 41 43 43 45 46 48 Appendix A: Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Performance and Supported Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traffic Management and QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MF2201 MetroFlex Wireless Access Gateway User’s Guide 51 51 52 52 8000003, December 2005 Who Should Use this Guide Preface This MF2201 MetroFlex Wireless Access Gateway User’s Guide will help you understand the MF 2201 MetroFlex Wireless Access Gateway, how to install it, and configure it using the Ruckus Wireless Web Interface. Who Should Use this Guide This User’s Guide assumes that the reader has basic to intermediate computer and Internet skills. All the basic computer networking, Internet, and other information required to configure this device is provided herein. What You’ll Find in this Guide The following topics are covered: • Chapter 1: “Introduction” • Chapter 2: “Installation and Setup” • Chapter 3: “Using the Ruckus Wireless Web Interface” • Appendix A: “Technical Specifications” Typographic conventions This User’s Guide uses the following typographic conventions: Table 1—Typographic conventions Typeface or Symbol Meaning Example italics Emphasis, book titles, CD names, special terms. Read your User’s Guide thoroughly. Also used to denote optional input if surrounded byEnter an address in the range bold System menu names, user input Open the Control Panel. fixed Screen text, URLs, IP addresses Browse to the following IP address: 192.168.0.<2-253> http://192.168.0.254 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide System Requirements System Requirements The MF 2201 MetroFlex Wireless Access Gateway is compatible with most contemporary personal computers and operating systems that are configured for Internet and wireless networking. The MF 2201 Gateway is accessed and configured via a Web browser interface. Any of the following Web browsers are supported: • Microsoft Internet Explorer 5.0 and higher • Netscape version 6.0 and higher • Apple Safari 1.0 and higher • Mozilla Firefox version 1.0 and higher Support and Warranty Information See the Warranty and Support card for detailed information about contacting Technical Support, and the Warranty terms for your MF 2201 MetroFlex Wireless Access Gateway. MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Chapter 1: Introduction Congratulations on your purchase of the MF 2201 MetroFlex Wireless Access Gateway The MF 2201 is a purpose-built home gateway to deliver the best possible connectivity from subscriber homes to MetroMesh Wi-Fi networks. MetroMesh Wi-Fi networks provide coverage across wide area using a mesh distribution of access points based on standard WiFi protocols. The installation uses outdoor high power MetroMesh routers to achieve coverage for outdoor wireless devices. Typically, the indoor coverage is inadequate to maintain an acceptable level for users within the home. The MF 2201 is a Customer Premise Equipment to allow the extension of the Metro Wifi signals to achieve a robust coverage within home. The MF 2201 communicates with the MetroMesh routers to allow home devices (such as PC or laptops) to access the Internet. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide MetroFlex™ A typical installation consists of a Ruckus Wireless, Inc. MF 2201 MetroFlex Wireless Access Gateway connected to a set top box. The MF 2201 Gateway receives wireless signals from a MediaFlex 2900 Multimedia Access Point or other remote AP that is connected to a DSL router or cable modem. Video, data and voice traffic are distributed among TV, video appliances, and other wireless-enabled home entertainment appliances. Ruckus MF2201 for predictable broadband connection to metro Wi-Fi service In-home broadband router Existing in-home Wi-Fi Ruckus MF2201 Existing Wi-Fi AP provides in-home IP connectivity Figure 1—The MF 2201 MetroFlex Wireless Access Gateway in a Typical Home Network MetroFlex™ MetroFlex™ is Ruckus Wireless, Inc.’s family of purpose-built, multimedia WiFi appliances that enable reliable wireless metro-area wi-fi network access. MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 BeamFlex™ BeamFlex™ BeamFlex™ is Ruckus Wireless, Inc.’s patent-pending antenna technology that allows wireless signals to navigate around interference, extend wireless signal range, and increase speeds and capacity for 802.11b/g wireless networks. The BeamFlex™ antenna system consists of an array of six high-gain antenna elements, that allow the MF2201 to find quality signal paths in a changing environment, and sustain the baseline performance required in a metro wi-fi environment. Key Features BeamFlex™ Smart MIMO Antenna Maximizes Wireless Range and Performance • Multi-In, Multi-Out (MIMO) technology supports real time learning of Radio Frequency, station, network and application conditions. • On-the-fly adaptation to each receiving device in response to environmental changes such as interference to maximize signal quality, data rate and minimize packet errors and retransmissions. • Internal driver software controls an antenna array with 6 high-gain, directional antenna elements and 63 unique antenna combinations. • Expert system 802.11 driver controls data rate and retransmission policies on a per-packet basis. Media QoS Ensures Highest Video Quality • Automatic traffic classification and Type-of-Service (TOS) tagging eliminates complex QoS configurations. • Priority queuing for voice, video, best-effort and background traffic, per WiFi Alliance WiFi Multimedia (WMM) specifications. • Strict priority with short (2 frames) hardware queue depth to ensure rapid feedback from the remote AP. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide Key Features Multiple Concurrent Video Streams with Simultaneous Data Traffic • Delivers 15-20 Mbps of bandwidth at 99.9% availability throughout a typical 2500ft2 (300m2) home. • Supports one MPEG-4/WMV stream, one DVD-quality MPEG-2 streams, or one 10Mbps+ high definition video stream at 50ft (18m), with simultaneous data traffic. Simple Configuration and Installation • Simple Web-based user interface for easy configuration and customization of features such as SSID, WEP or WPA key, statistics monitoring and software upgrade. Standards-based Solution Protects User Investment, Minimizes Replacement Cost • Compliant with 802.11b and 802.11g: supports 802.11g wireless networking at up to 108 Mbps; and can interoperate in 802.11g-only or mixed networks. • Compliant with 802.1x (WEP and WPA with TKIP) and Wi-Fi Alliance WMM specifications. • Supports Wi-Fi Protected Access-Pre-Shared Key (WPA-PSK) data encryption. WPA provides strong data encryption and authentication based on a pre-shared key. • Supports 64-bit and 128-bit WEP encryption security. WEP keys can be generated manually or by passphrase. • Attaches to television set-top box via Ethernet to optimize the reception of quality internet video over the WLAN. • Forward compatible with the emerging 802.11n WLAN standard. 10 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Chapter 2: Installation and Setup This chapter describes how to install your MF 2201 MetroFlex Wireless Access Gateway, and how to set up your PC to connect to the Ruckus Wireless Web Interface. Topics covered in this chapter include: Packing List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 MF 2201 MetroFlex Wireless Access Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 LED Status Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Placement Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Connecting to the MF 2201 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Accessing the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 11 Packing List Packing List 1. MF 2201 MetroFlex Wireless Access Gateway 2. AC power adapter (Input DC 5-18V 1-2A) 3. Category 5 (CAT5) Ethernet Cable 4. MF 2201 MetroFlex Wireless Access Gateway Quick Setup Guide MF 2201 MetroFlex Wireless Access Gateway Front View Figure 2— “Front View of the MF 2201 MetroFlex Wireless Access Gateway” shows the front view MF 2201 Gateway, with the LED indicators numbered. The numbers correspond to the labels describing LED behavior in Table 2— “LED Indicators and Meanings” on page 13. Figure 2—Front View of the MF 2201 MetroFlex Wireless Access Gateway 12 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 LED Status Lights LED Status Lights Table 2— “LED Indicators and Meanings” describes the LED lights on the front of the MF 2201 Gateway. Table 2—LED Indicators and Meanings Label LED Activity Description Antenna All LEDs On Green Solid The MF 2201 Gateway is booting. Power LAN Wireless Air Quality 8000003, December 2005 Green Flashing randomly The lit LEDs indicate which antennae are active. Green Power is supplied to the MF 2201 Gateway. Off Power is not supplied to the MF 2201 Gateway. Green Steady The MF 2201 Gateway has link. Off The MF 2201 Gateway has no link. Green Flashing The MF 2201 Gateway is transmitting data. The faster the flashing, the more data is being transmitted or received. Green Steady The Wireless port is initialized and enabled. Green Steady Good Air Quality: A steady Green LED indicates that the current environment will support quality video streaming. Green Flashing Marginally Acceptable Air Quality: a flashing Green LED (on for 0.25 second, off 0.25 second) indicates that the current environment does not always meet the video standard. While video streaming is possible, the quality will vary. Green intermittent Flashing Bad Air Quality: A briefly flashing Green LED (on for 0.03 second and off for 1 second) indicates that video streaming is not possible in the current environment. The brief flash also indicates that the device is still functioning. MF2201 MetroFlex Wireless Access Gateway User’s Guide 13 LED Status Lights Rear View Figure 3—Rear View of the MF 2201 Gateway Table 3—Rear Ports and Adapters Label Description AC Power Adapter (Input: DC 5V 2A) 10/100 Mbps Auto-sensing, autonegotiating RJ-45 network port Reset button. Used only if you need to reset the MF 2201 Gateway to its factory default settings. Insert the end of a paper clip or pin into the hole and hold it in for at least 4 seconds. 14 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Placement Guidelines Placement Guidelines You or your service provider or installer can determine the best placement for the MF 2201 Gateway by using the following guidelines. Establishing a good general location Your MF 2201 Gateway should be placed: • On a shelf or other elevated location away from any physical obstructions. • Away from other sources of electromagnetic interference (for example, microwave ovens, and cordless phones). • Away from large metal surfaces, pictures or mirrors. • Away from large furniture or other physical obstructions. Using the Air Quality Indicator to fine-tune the placement Wireless environments are sensitive to the physical arrangement of both electronic devices and furniture in a room. You or your installer can observe the Air Quality Indicator LED to determine the best location. The Air Quality indicator LED is described in Table 2— “LED Indicators and Meanings” on page 13. Your service provider or installer can guide you through a self-help troubleshooting session if video quality deteriorates after an installation. Or, you may be able to determine a solution to the problem on your own. If “Bad” or “Maybe Acceptable,” air quality is indicated, you can adjust the location of the MF 2201 Gateway and other devices until a steady green LED indicates “good” air quality. Connecting to the MF 2201 Gateway Before using the MF 2201 Gateway, you have to configure it to work within your home network. Your service provider or installer will likely perform all installation tasks for you, or you may read the following section to understand how to configure it manually. The default IP address of the MF 2201 MetroFlex Wireless Access Gateway is 192.168.0.254. To gain administrative control of the unit, set your PC or laptop network IP address to an address within the same network as the MF 2201 Gateway’s default IP address. Then, connect your PC to the MF 2201 Gateway using the provided Ethernet cable. You can set your PC’s IP address to an address within the network 192.168.0.<2-253> (Example: 192.168.0.100). Manually Configuring an IP Address on Your PC 1. Windows 2000: Start>Settings>Network and Dial-up Connections Windows XP: Start>Settings>Control Panel>Network Connections 2. Double-click the icon for the Local Area Connection designated for your home network, then click the Properties button at the bottom of the screen. (This is not the same icon as your home wireless network.) 3. In the Local Area Connection Properties window, select Internet Protocol (TCP/IP) and click the Properties button. The Internet Protocol (TCP/IP) Properties window appears ( Figure 4). 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 15 Connecting to the MF 2201 Gateway Figure 4—Internet Protocol (TCP/IP)Properties Window 4. Select the Use the following IP address button, and enter an IP address within the network as noted above. 5. Press Tab and allow the Subnet mask address to auto-fill to 255.255.255.0. 6. Click OK to exit the TCP/IP Properties window. 7. Click OK to exit the Local Area Connection Properties window. Connecting a PC to the MF 2201 Gateway The following steps will guide you through connecting to your MF 2201 Gateway. 1. Remove the MF 2201 Gateway from the packaging and place it next to your PC or laptop. 2. Connect the AC Power Supply to the MF 2201 Gateway and connect to a power outlet. 3. Connect your PC or laptop to the Ethernet port on the MF 2201 Gateway using the supplied Ethernet cable. 4. On your PC, open a browser window. Enter the address http://192.168.0.254. 5. When the login screen appears, enter the username admin and leave the password field blank. Then click Logon. CAUTION:—Make sure to write down the new IP address, username, password and SSID. If you change the MF 2201 Gateway’s default IP address to one outside the current address range of your PC, you will not be able to connect to the device after reboot until you reset your computer’s IP address to be within the same network as the MF 2201 Gateway. See Table 5, “Wireless Network Settings Worksheet,” on page 20 and Table 6, “MF 2201 Gateway Default and User Settings Worksheet,” on page 21 for more information. 16 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Accessing the Web Interface You should now be able to find the default SSID “V54” of your MF 2201 Gateway over your wireless connection: Table 4—Default Wireless Settings Wireless Feature Setting Network Name (SSID) V54 Security Disabled Accessing the Web Interface The MF 2201 Gateway provides a Web-based user interface for configuration and monitoring. For information about using the Ruckus Wireless Web Interface, refer to Chapter 3:, “Using the Ruckus Wireless Web Interface . 1. To access the Ruckus Wireless Web Interface, launch a Web browser and enter the MF 2201 Gateway’s IP address. If this is the first time the access point is being configured, enter the default IP address: 192.168.0.254 2. A logon screen will appear. Use the default logon information: Username: admin Password: After logging in, you will see the main information page. On the information page, there are two panes. The pane on the left shows major information or configuration points. Each major information or configuration area has a number of sub-menus. Clicking on the relevant menu will bring the relevant page onto the screen. The system monitors the activities on the Web user interface. If you do not use the Web interface for more than five minutes, the system will time out, and you will be logged out automatically. You need to re-log in to access the interface. CAUTION:—Any configuration changes will be lost unless you use the Update button. It is recommended that after each configuration screen you modify, you click the Update button. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 17 Accessing the Web Interface 18 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Chapter 3: Using the Ruckus Wireless Web Interface This chapter describes the tasks you need to do to customize the MF 2201 Gateway to run on your wireless network. Topics covered in this chapter include: Wireless Settings Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 MF 2201 Gateway Settings Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ruckus Wireless Web Interface Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Air Quality Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Configuring the MF 2201 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Viewing Wireless Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Viewing Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Rebooting the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Taking a System Support Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 19 Wireless Settings Worksheet Wireless Settings Worksheet Before you modify any wireless settings on the MF 2201 Gateway, print Table 5— “Wireless Network Settings Worksheet” and record the following information about your wireless network. Your ISP or network administrator may provide you with this information. The wireless information recorded in this worksheet should be used to configure the MF 2201 Gateway’s wireless settings. Table 5—Wireless Network Settings Worksheet Item Description and Your Network Setting MF 2201 Gateway SSID The MF 2201 Gateway will not provide Internet access like a home router or gateway. The SSID identifies the remote AP. Make sure to specify the SSID of the remote AP. Do not specify a unique SSID for the MF 2201 Gateway. You can use up to 32 alphanumeric characters. The SSID is case sensitive. Security If using WEP, circle the method used: Open SystemShared KeyAuto Circle the type of Shared key: 64-bit 128 bit Passphrase method • • If using 64-bit WEP: use 10 hex digits (any combination of 0-9 or a-f) or 5 ascii characters If using 128-bit WEP, use 26 hex digits or 13 ascii characters The WEP key values are not case-sensitive. Key 1 ______________________________________________ Key 2 ______________________________________________ Key 3 ______________________________________________ Key 4 ______________________________________________ If using WPA-PSK, write down the passphrase. The WPA-PSK passphrase is case-sensitive. WPA Passphrase: 20 ________________________________ MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 MF 2201 Gateway Settings Worksheet MF 2201 Gateway Settings Worksheet Print Table 6, and record your personalized settings for configuring the MF 2201 Gateway. Enter the security settings you recorded in Table 5, “Wireless Network Settings Worksheet,” on page 20. Remember—If the MF 2201 Gateway’s device settings do not match the remote AP settings, the MF 2201 Gateway will not be able to find your network. Store this information in a safe place. Table 6—MF 2201 Gateway Default and User Settings Worksheet Item Default Setting User Name admin Your Setting _______________________________ Password _______________________________ IP Address 192.168.0.1 _______________________________ Subnet Mask 255.255.255.0 _______________________________ SSID V54 _______________________________ Wireless Mode 802.11g&b _______________________________ Security Disabled _______________________________ 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 21 Ruckus Wireless Web Interface Menus Ruckus Wireless Web Interface Menus The Ruckus Wireless Web Interface menus are located on the left-hand navigation pane. To select a particular menu, simply click on the menu link. Common Buttons The Ruckus Wireless Web Interface screens contain the following menu buttons (Table 7): Table 7—Wireless Web Interface Menu Buttons Button Action Logout Logs out the current session. Restore Restores the original configuration. Update Saves the new configuration. Next Progresses to the next menu. Only found in the Configuration menus. Back Reverts to the previous menu. Only found in the Configuration menus. Air Quality Indicator The Air Quality indicator icon shows the current state of your Wireless connection. Air Quality is measured by the Received Signal Strength Indication (RSSI) value, which is a measurement of the wireless signal strength. A high RSSI value usually means that the wireless connection is stable, and quality video data can be transferred. 22 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Air Quality Indicator The Air Quality Indicator assesses the environment that surrounds a Ruckus Wireless, Inc. MF 2201 Gateway, and determines the amount of interference in the infrastructure. The Radio Frequency (RF) side of a wireless device is a combination of a receiver and a transmitter. Both receiver and transmitter provide feedback as they operate. The Air Quality indicator bases its evaluation on the Received Signal Strength Indication (RSSI) that is returned as part of the 802.11 transmission acknowledgement. As the adapter receives an 802.11 packet, it sends the RSSI value to the remote AP. Thumb Up: Good air quality. The environment supports a quality video viewing experience. Thumb sideways: Marginal video signal strength. The current environment may support video viewing, but it is also possible that the video may be flawed. Thumb down: Low video signal strength. The current environment does not support quality video viewing. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 23 Configuring the MF 2201 Gateway Configuring the MF 2201 Gateway This section describes the tasks and screens used to customize the MF 2201 Gateway configuration to run on your wireless network. Review the following topics before you change any system configuration settings: • "Connecting to the MF 2201 Gateway" on page 15 • "Accessing the Web Interface" on page 17. System Configuration Table 6, “MF 2201 Gateway Default and User Settings Worksheet,” on page 21 shows the default settings used to login to the device. A minimum set of configurations is required to put the MF 2201 Gateway into operational mode. The system provides the default settings for these configuration items. You should change the default settings where necessary to match your own wireless network’s configuration, and to protect your privacy. A system reboot is required for configuration changes to take effect. Follow the following steps to configure the MF 2201 Gateway: 1. Connect to the MF2201 adapter by following the instructions in "Connecting to the MF 2201 Gateway" on page 15. 2. Choose Configuration->System.. The window of Figure 5 appears. Figure 5—System Configuration 24 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Configuring the MF 2201 Gateway 3. Enter your configuration changes in the appropriate fields. 4. Click the Next button to go to the next configuration screen. 5. Click the Update button to save your settings. CAUTION:—You must click the Update button to save any configuration changes. The Ruckus Wireless Web Interface will timeout after 5 minutes of inactivity. If you let the system time out before clicking the Update button, any changes you made will be lost. 6. Click the Restore button to cancel configuration changes. 7. Go to the Boot menu and click the Reboot button to reboot the device for configuration changes to take effect. CAUTION:—If, after having changed any default settings, you have forgotten what the new settings are, you may not be able to login to the MF 2201 Gateway. To regain access to the MF 2201 Gateway, you must reset the device to its factory default settings. Do this by inserting the end of a paper clip into the Reset Button while the unit is on and keep holding the button down until the green LEDs at the top of the unit briefly go out— indicating the system is rebooting. Customizing the System Configuration It is recommended that you customize the username and password so that you can control who can gain administrative access to the MF 2201 Gateway. You may also wish to change the default IP address if it conflicts with another device in your wireless network. Refer to Table 8 for details on each field. Table 8—System Configuration Field Description IP Address The IP address of the MF 2201 Gateway. This IP address is used only when you need to access the Ruckus Wireless Web Interface to change configuration or view information about the MF 2201 Gateway. Subnet Mask The subnet mask of the MF 2201 Gateway. The default is 255.255.255.0. Changing the Subnet Mask field is not recommended for most installations. Default Gateway The IP address of default gateway. The default is 0.0.0.0. User Name The user name. The default user name is admin. If you change the user name, make sure to write it down for future reference. Password / Confirm The user password. The default is no password. If you change the password, make sure to write it down for future reference. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 25 Configuring the MF 2201 Gateway Configuring the Wireless Interface It is recommended that you consult with your service provider to understand the wireless settings. Before changing any settings in the Wireless configuration menu, make sure you have recorded and verified the information in the following worksheets: • "Wireless Network Settings Worksheet" on page 20 • "MF 2201 Gateway Default and User Settings Worksheet" on page 21. 1. After connecting to the MF 2201 Gateway, choose Configuration->Wireless. The window of Figure 6 appears. Figure 6—Wireless Interface Configuration 26 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Configuring the MF 2201 Gateway 2. Fill in the parameters as described in Table 9. Table 9—Wireless Interface Configuration Field Description SSID The SSID (Service Set IDentifier) is the name of the wireless network. The default SSID is V54, but it is strongly recommended that you change your SSID. If there are other wireless networks in your area, you should give your wireless network a unique name. The SSID can consist of up to 32 characters. Wireless mode The wireless mode options are: • Country Code 2.4GHz 54Mbps (802.11g&b) - allows both 802.11g- and 802.11b-compliant devices to join the network. This is the default setting. Sets your country or region code. Selecting the incorrect country or region may result in violation of applicable law. The selectable countries or regions are United States, Europe, Hong Kong, and Japan. NOTE – For MF 2201 Gateways shipped in the United States, the country code cannot be modified. The country code is pre-defined for United States only. Advanced Setting This button provides access to the advanced wireless settings. Advanced wireless settings are for advanced configuration or testing purposes only. Changing the advanced settings may negatively affect the operation of the MF 2201 Gateway and is not recommended. Security The wireless security options are: • • • Edit Security Setting 8000003, December 2005 Disabled: This setting disables all encryption, so traffic is sent in the clear. This setting is not recommended. WEP: This setting enables Wired Equivalent Privacy. WEP Shared Key authentication and WEP data encryption provides sufficient security in most cases. WPA-PSK: Wi-Fi Protected Access, Pre-Shared Key (WPA-PSK). Each packet of information is encrypted with a different key. Provides very strong security, but may not be supported on older systems. Click this button to edit the security setting of WEP keys or the WPA-PSK passphrase. MF2201 MetroFlex Wireless Access Gateway User’s Guide 27 Configuring the MF 2201 Gateway Advanced Wireless Configuration The Advanced Wireless Configuration menu is preconfigured with the optimum settings. Changing the advanced settings may negatively affect the MF 2201 Gateway’s operation, or completely disable it. For best results, leave the Advanced settings at their default values and do not change these settings unless directed by your technical support personnel. NOTE – If you have modified the advanced settings and wish to revert to the original settings, you can restore the settings by clicking the Restore button, as long as you have not already clicked the Update Button. 1. After connecting to the MF 2201 Gateway, choose Configuration->Wireless. Then click Advanced. The window of Figure 7 appears. Figure 7—Advanced Wireless Configuration 28 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Configuring the MF 2201 Gateway Table 10 shows the Advanced Wireless Configuration parameters. Table 10—Advanced Wireless Configuration Parameters Field Description Wireless Mode Sets the wireless mode for the MF 2201 Gateway. The wireless mode determines the wireless speed of devices that are allowed to associate to the MF 2201 Gateway. Options are: • • • • 802.11g&b: stations running at either 802.11g (2.4GHz, 54Mbps) or 802.11b (2.4GHz 11Mbps) can associate to the MF 2201 Gateway. This is the default setting. 2.4GHz 54Mbps (802.11g only) 2.4GHz Auto 108Mbps (802.11g Turbo) 2.4GHz Only 108Mbps (802.11g Turbo) CAUTION:—Using Turbo and/or super G mode is NOT supported when running video streams. These modes are intended for diagnostic and for networks where only non-video traffic is transmitted. Super G This check box is used to enable the Super G mode, which engages advanced mechanisms when extra bandwidth is available and or required. By default, this option is not checked. Data Rate Select the desired data rate from the drop-down menu. The default is Best, which means the system will adjust the data rate automatically. Transmit Power Select the desired Adapter transmit power from the drop-down menu. In cases where you might want to limit your signal coverage range, such as in a small apartment or room, you can select a lower transmit power. The options are: • • • • • Full Half (-3 dB) Quarter (-6 dB) Eighth (-9 dB) Minimum The default is Full. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 29 Configuring the MF 2201 Gateway Table 10—Advanced Wireless Configuration Parameters (Continued) Field Description Fragment length The fragment length. The range is between 256 and 2346 bytes. The default is 2346. The MF 2201 Gateway uses fragmentation to divide 802.11 frames into smaller fragments which are sent separately to the destination. Only unicast frames can be fragmented. The fragment length can be between 256-2346 bytes. If the data that the MF 2201 Gateway is transmitting is larger than the threshold, it will trigger the fragmentation function. If the packet size is equal to or less than the threshold, the access point will not use fragmentation. In a good wireless environment, the larger the fragment, the more efficient the network operates. In a noisy environment, the fragment length should be adjusted to a smaller size to minimize retransmission and increase the reliability of the transmission. RTS/CTS Threshold The RTS-CTS threshold range. The range is between 256 and 2346. The default is 2346. The RTS-CTS threshold is a value that determines at what frame length the request-to-send/clear-to-send (RTS-CTS) function is triggered. By default, this threshold is set at its highest value. A lower threshold value means that the RTS-CTS function is triggered for smaller frame lengths. A lower threshold may be necessary in environments with excessive signal noise or hidden nodes; but this may result in some performance degradation. We need to make a glaring warning about not using turbo or super G when using IPTV applications. Something like: Using Turbo and/or super G mode is NOT supported when running video streams, these modes are intended for diagnostic and for networks where only non-video traffic is transmitted. CAUTION:—Using Turbo and/or super G mode is NOT supported when running video streams, these modes are intended for diagnostic and for networks where only non-video traffic is transmitted. Configuring WEP Security 1. Click Configuration ->Wireless in the left-hand navigation pane. The window of Figure 6 appears. 2. Select WEP in the Security drop-down menu. 3. Click the Edit Security Settings button.TheWEP Configuration window of Figure 8 appears. 30 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Configuring the MF 2201 Gateway Figure 8—WEP Configuration Window Table 11 explains the WEP Configuration parameters. Table 11—WEP Configuration Field Description Open System No authentication is enforced. Shared Key Authentication using a shared key. Shared Key authentication encrypts the SSID and data. Auto Automatically selects the authentication mode depending on the method used by the remote AP. Key Entry Method The key entry method options are: • • 8000003, December 2005 Hexadecimal: Accept entering encryption key with hexadecimal (0-9, A-F). Ascii Text: Accept entering encryption key with ASCII characters. MF2201 MetroFlex Wireless Access Gateway User’s Guide 31 Configuring the MF 2201 Gateway Table 11—WEP Configuration (Continued) Key Length The valid key length options are: • • • None: No key. 40 bit WEP: Key with 10 hexadecimal digits or 5 ASCII characters. 128 bit WEP: Key with 26 hexadecimal digits or 13 ASCII characters. PassPhrase This allows automatic key generation. Enter the desired passphrase and click on the Generate button. The system will generate all four WEP keys automatically. Default Shared Key The default share key number. There are four shared keys; select one of these keys as the default. Make sure your MF 2201 Gateway uses the same default shared key as the remote AP. Encryption Keys These fields auto-fill if you use a passphrase to generate keys. If your network doesn’t use Ruckus Wireless, Inc. APs or adapters, enter each key manually according to the Key Entry Methods and Key Length settings. You may specify up to four different keys and select the desired default shared key. 4. In the Configuration->Security (WEP) menu, select open system, shared key, or Auto. See Authentication below for more information. 5. Select the Key Entry Method: Hexadecimal or Ascii Text. 6. Select the Key length: 40 bit WEP or 128 bit WEP. 7. If your MF 2201 Gateway will be used with an MF2900 AP, you may use the same passphrase to generate four unique keys. Enter a passphrase and press the Generate button. If using a remote AP from another manufacturer, you should manually enter the four WEP keys in the same order. 8. Click the Update button to save your settings. Authentication WEP allows three authentication options: open system, shared key, or automatic selection of authentication method. Under an open system, a shared key is not required for the adapter to authenticate to a remote AP such as the Ruckus Wireless, Inc. MF2900 AP. However, a shared key must still be used to encrypt and decrypt data between the MF 2201 Gateway and the remote AP. Shared key authentication adds another layer of security by requiring that the MF 2201 Gateway supply a shared key first to authenticate to the remote AP, and then supply the same shared key for encrypting and decrypting data. Using a Passphrase to Generate Keys The MF 2201 Gateway supports automatic generation of four keys from a passphrase. Make sure that the passphrase is the same as the passphrase used on the remote AP. 1. Enter a word or group of printable characters in the Passphrase box and click the Generate button. The passphrase is case sensitive; e.g. MediaFlex is not the same as MEDIAFLEX. The four key boxes will be automatically populated with key values. 2. Click the Update button to save your settings. 32 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Configuring the MF 2201 Gateway Configuring WPA PSK WPA PSK configuration menu allows automatic key generation based on a single passphrase. WPA PSK provides very strong security, but may not be supported on older systems. If you configure the MF 2201 Gateway with WPA-PSK, the other devices in the network will not connect unless they, too are set to WPA-PSK, and are configured with the same passphrase. 1. Click the Configuration -> Wireless link in the left-hand navigation pane ( Figure 6). 2. Select WPA-PSK in the Security drop-down menu. 3. Click the Edit Security Settings button.The WPA Configuration appears ( Figure 9). Figure 9—WPA Configuration Table 12 explains the WPA Configuration parameters Table 12—WPA Configuration Field Description PassPhrase / Confirm Enter a passphrase and enter it again in the Confirm field. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 33 Viewing System Information 4. In the Configuration ->Security (WPA-PSK) menu, enter a passphrase and enter it again in the Confirm field. 5. Click the Update button to save your settings. Viewing System Information The Information Screens provide information the MF 2201 Gateway settings. System Information The System Information screen is the first screen to appear once you login to the MF 2201 Gateway. Figure 10 shows the System Information window. Figure 10—System Information Window 34 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Viewing Wireless Information Table 13 explains the System Information Parameters. Table 13—System Information Parameters Field Description System Name The local name for the MF 2201 Gateway. MAC Address The MAC address of the MF 2201 Gateway, or the station behind the adapter. IP Address The IP address of the MF 2201 Gateway. Uptime The system uptime since last reboot, displayed in HH:MM:SS (hours, minutes, seconds). H/W Version The hardware revision. S/W Version The firmware version that is currently operating. Creation Date The date/time that the firmware was created. Viewing Wireless Information The Wireless information menu shows the current wireless configurations for the MF 2201 Gateway. To view this window, click Information->Wireless from any window. Figure 11 shows the Wireless Information Window. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 35 Viewing Wireless Information Figure 11—Wireless Information Window Table 14 shows the Wireless Information Window parameters. Table 14—Wireless Information Window Parameters Field Description SSID The SSID (Service Set Identifier) is the name of the wireless network. BSSID The BSSID is the MAC address of the remote AP that the MF 2201 Gateway associated to. Wireless Mode The wireless mode, such as 2.4 GHz 54Mbps (802.11b/g) Channel The wireless channel number and operating frequency in MHz. Country code The country in which the MF 2201 Gateway is operating.The country code will automatically select the Channels available for that country. Encryption Describes the encryption type currently in use. The encryption types are WEP, WPA-PSK, or disabled. For more information about each type of encryption, see Table 9— “Wireless Interface Configuration” on page 27. 36 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Viewing Statistics Viewing Statistics The Statistics Screens provide statistics for a Local Area Network (LAN) interface, the wireless interface and wireless stations. Viewing LAN Interface Statistics The LAN Interface statistics windows show information about packets traversing the LAN connected to the MF 2201 Gateway. To view the LAN interface statistics, choose Statistics->LAN from any window. Figure 12 shows the LAN Statistics Window. Figure 12—LAN Statistics Window Table 15 explains the LAN Statistics window parameters. Table 15—LAN Statistics Window Parameters Field Description Unicast Packets The total number of unicast packets received or transmitted by the interface. Multicast Packets The total number of multicast packets received or transmitted by the interface. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 37 Viewing Statistics Table 15—LAN Statistics Window Parameters (Continued) Field Description Discard Packets The total number of received packets that were discarded by the interface. Error Packets The total number of error packets received or transmitted by the interface. Rx No Resource The number of received packets that are discarded by the interface due to no system resources. Rx Error Drop The number of received packets that are discarded by the interface due to a hardware error. Rx Unknown Protocols The number of received packets that are discarded by the interface due to an unknown protocol. RX No Desc Interrupts The number of received packets that are discarded by the interface due to no descriptor interrupt. RX Stopped Interrupts The number of received packets that are discarded by the interface due to stopped interrupts. BUS Error The number of received packets that are discarded by the interface due to a BUS error. Viewing Wireless Statistics The Wireless statistics menu shows the link, traffic, and security settings for the MF 2201 Gateway. To view this menu, choose Statistics-Wireless from any window. The Wireless Statistics Window of Figure 13 appears. At the top of this menu, MF 2201 Gateway’s MAC address will display as either joined or disconnected to the remote AP. 38 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Viewing Statistics Figure 13—Wireless Statistics 1. Click the Auto Update button to receive periodic updates to these statistics. The button will then display as Stop Update. 2. Click the Stop Update button if you do not wish to receive periodic updates. Table 16 shows the Wireless Statistics parameters. Table 16—Wireless Statistics Field Description Throughput (bps) The average receive or transmit throughput in bits-per-second. Maximum Throughput The high water mark receive or transmit throughput in bits-per-second. Good Packets The total number of good packets received or transmitted by the interface. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 39 Viewing Statistics Table 16—Wireless Statistics (Continued) Field Description Bad Packets The total number of good packets received or transmitted by the interface. Authentication Type The authentication type configured on the MF 2201 Gateway. Encryption The state of encryption configured on the MF 2201 Gateway. Unicast Cipher The type of unicast cipher used. Multicast Cipher The type of multicast cipher used. Power Save The state of power save mode: on or off. MSDU The number of MSDU (Mag Service Data Unit) received or transmitted by the interface. Data The number of data packets received or transmitted by the interface. Multicast The number of multicast packets received or transmitted by the interface. Management The number of management packets received or transmitted by the interface. Control The number of control packets received or transmitted by the interface. Errors The total number of error packets received or transmitted by the interface. Signal Strength (RSSI) The RSSI value received or transmitted by the interface. Data Rate (Mbps) The data rate in Mbps received or transmitted by the interface. Receive Errors The total number of error packets received by the interface. Discarded Frames The number of received or transmitted packets that were discarded by the interface. Duplicate Frames The number of duplicate packets received or transmitted by the interface. CRC Errors The number of packets with CRC error received or transmitted by the interface. Decrypt Errors The number of packets with decryption error received or transmitted by the interface. PHY Errors The number of packets with PHY error received or transmitted by the interface. DMA Errors The number of packets with DMA error received or transmitted by the interface. Transmit Errors The total number of error packets transmitted by the interface. 40 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Viewing Statistics Table 16—Wireless Statistics (Continued) Field Description Discarded Frames The total number of frames discarded by the interface Excessive Retries The total number of retries that exceed the predefined threshold. DMA Errors The number of packets with DMA error received or transmitted by the interface. Viewing Remote AP Statistics The Remote AP statistics menu shows statistics specific to a remote AP to which the MF 2201 Gateway is associated. To view this menu, choose Statistics->Remote AP from any window. Figure 14 shows the Remote AP Statistics Window. Figure 14—Remote AP Statistics 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 41 Viewing Statistics describes the Remote AP Statistics parameters. Table 17—Remote AP Statistics Field Description Authentication Type The authentication type used by the remote AP. Encryption The state of encryption used by the remote AP. Cipher Advertised The cipher advertised by the remote AP. MSDU The number of MSDUs (Mag Service Data Units) received or transmitted by the remote AP. Data The number of data packets received or transmitted by the remote AP. Multicast The number of multicast packets received or transmitted by the remote AP. Management The number of management packets received or transmitted by the remote AP. Control The number of control packets received or transmitted by the remote AP. Errors The total number of error packets received or transmitted by the remote AP. Receive Errors The total number of error packets received or transmitted by the remote AP. Discarded Frames The number of received or transmitted packets that were discarded by the remote AP. Duplicate Frames The number of duplicate packets received or transmitted by the remote AP. CRC Errors The number of packets with CRC error received or transmitted by the remote AP. Decrypt Errors The number of packets with decryption error received or transmitted by the remote AP. PHY Errors The number of packets with phy error received or transmitted by the remote AP. DMA Errors The number of packets with DMA errors received or transmitted by the remote AP. Transmit Errors The number of packets with transmit errors received or transmitted by the remote AP. 42 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Updating the Firmware Table 17—Remote AP Statistics Field Description Discarded Frames The number of discarded frames received or transmitted by the remote AP. Excessive Retries The number of excessive retries received or transmitted by the remote AP. DMA Errors The number of packets with DMA errors received or transmitted by the remote AP. Updating the Firmware This menu provides a utility for updating the MF 2201 Gateway’s firmware. A firmware update may be necessary or desirable to add new features, important fixes or enhancements to the MF 2201 Gateway. Contact your service provider for more information about Web sites or TFTP/FTP sites used to store firmware images for the MF 2201 Gateway. CAUTION:—If you have recently made configuration changes to the MF 2201 Gateway, make sure to reboot the system (see “Rebooting the System” on page 46) first so that your changes are preserved. Then update the firmware. Performing a Web Download To download a firmware image from a Web site and use it to update the firmware on the MF 2201 Gateway: 1. Point your browser to the Web site where the MF 2201 Gateway’s firmware is stored, and download the firmware image to a folder on your hard drive. Note the location of the downloaded image. 2. In the Ruckus Wireless Web Interface, click the Maintenance->Upgrade menu. The window of Figure 15 appears. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 43 Updating the Firmware Figure 15—Updating the Firmware 44 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Updating the Firmware Table 18 describes the Updating the Firmware parameters. Table 18—Updating the Firmware Field Description Web Download If you have downloaded a Firmware image from a Web site and stored it locally on your PC, you can click the Browse... button to select the image. The path to the image will appear in the Local File Name: field. Click the Update Firmware button located below Local File Name field. TFTP/FTP Download Allows you to use a TFTP or FTP server to download a firmware image. • • • • Host Name: enter the IP address of the server. User Name: enter the User Name that is used to access to the specified server. This is required only for an FTP server Password: enter the Password that is used to access to the specified server. This is required only for an FTP server. Image Name: enter the filename of the firmware image on the TFTP or FTP server. Click the Update Firmware button located below Image Name field. 3. Click the Browse... button to locate and select the firmware image. 4. Click the Update Firmware button to perform the update. 5. If the firmware has updated successfully, a green check mark will appear. Click the Reboot button. 6. If the firmware did not update, a Failed: file type error message will appear. A file type error indicates that the firmware image may be corrupt or invalid. Try downloading the firmware image again, and repeat the above steps. TFTP or FTP Download To specify a specific trivial file transfer protocol (TFTP) or File Transfer Protocol (FTP) server from which to download a firmware image: 1. Choose the download method by selecting either the TFTP or FTP button. 2. Enter the IP address or Hostname of the server. 3. For FTP only: Enter the User Name and Password for the server. 4. Enter the name of the firmware image. 5. Click the Update Firmware button at the bottom of the screen to perform the upgrade. 6. If the firmware has updated successfully, a green check mark will appear. Click the Reboot button. 7. If the firmware did not update, a Failed: file type error message will appear. A file type error indicates that the firmware image may be corrupt or invalid. Check the TFTP/FTP server address and the firmware image name. Then try downloading the firmware image again, and repeat the above steps. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 45 Rebooting the System Rebooting the System You must reboot the system if you want your configuration changes to take effect.Two types of reboot are provided: The Reboot button re-starts the system. All the configurations that have been saved are preserved through the reboot. Rebooting is necessary in order to make your configuration changes permanent. • If the system times out and you have to re-login before setting the reboot, you configuration changes will be saved, as long as you have already clicked the Update button to save the current configuration. • If you have powered down or logged out of the MF 2201 Gateway before clicking the Update button and the Reboot button, your configuration changes will be lost. The Reboot to Factory Default button restarts the system with the factory default configurations. All previous configurations will be lost. 1. To reboot for either type, click Maintenance->Reboot from any window. The window of Figure 16 appears. Figure 16—Reboot Menu 2. Click the reboot option you want. The window of Figure 17 appears. 46 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Rebooting the System Figure 17—Reboot in Process During a reboot, the antenna LEDs on the top of the MF 2201 Gateway will momentarily go out, then light up again. How to tell when the Wireless Adapter is ready? After about 18 seconds, the antenna LEDs will light up in solid green, followed by intermittent flashing. This indicates the MF 2201 Gateway is ready. The Click here when Wireless Adapter is ready link will open the main login page. NOTE – If you have modified the device IP address, and then rebooted the device to factory default configuration, the above link will not work. Instead, click the Logout button, and then point your browser to the default IP address for the device. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 47 Taking a System Support Snapshot Taking a System Support Snapshot The Support menu enables you to take a system snapshot for further analysis and troubleshooting. The system snapshot can be sent and saved to a TFTP or FTP server for analysis by a technical support engineer. 1. To view the support menu, choose Maintenance->Support from any window. The Support Menu appears ( Figure 18). Figure 18—Support Menu Table 19 describes the support menu parameters. Table 19—Support Menu Field Description Server Type Select the server type: TFTP or FTP. File Name Specify the file name for the system snapshot that is to be saved on a TFTP or FTP server. 48 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Taking a System Support Snapshot 2. If you have not yet configured the TFTP or FTP server, click the Maintenance->Update link. 3. In the Firmware->Update menu, enter the TFTP or FTP server information. The same server is used for both upgrading the firmware and uploading the system snapshot. Your service provider or technical support contact should provide you with information for configuring the TFTP or FTP server. 4. Click on the Refresh button to get the current system snapshot. 5. Click on the Send To button to send the support.txt file to the TFTP or FTP server. You can set the address for the TFTP or FTP server in the Firmware Update menu. 6. Click the Upload link at the bottom of the page to upload to the specified server. 8000003, December 2005 MF2201 MetroFlex Wireless Access Gateway User’s Guide 49 Taking a System Support Snapshot 50 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005 Appendix A: Technical Specifications Physical Characteristics MF 2201 Gateway: 5V-18V 10W External power adapter: Power requirements Unifive Technology Co LTD, Model US300520, Input 100-240V AC, Output 5V DC 2A, UL Listed DVE, Model DSA-031F-12 UK 12, Input 100-240V AC, Output 12V DC 1A, TUV Certified DVE, Model DSA-031F-12 EU 12, Input 100-240V AC, Output 12V DC 1A, TUV Certified Physical size 5.72 x 4.92 x 2.9 in (145 x 125 x 74 mm.) Weight 0.53 lbs (0.24 kg) Antenna Internal software-configurable antenna array with six directional, high-gain elements and 63 unique antenna patterns Ethernet ports 1 auto MDX, auto sensing 10/100 Mbps, RJ45 port LED display Antenna Power LAN Wireless Air Quality Environmental conditions Operating Temperature: 32oF – 104oF (0oC – 40oC) Operating Humidity: 15% - 95% non condensing Electromagnetic Emissions Meets requirements of FCC Part 15 Class B Performance and Supported Configurations Target UDP throughput 8000003, December 2005 15-20 Mbps sustainable throughout a typical 2500 ft2 (300 m2) home MF2201 MetroFlex Wireless Access Gateway User’s Guide 51 Traffic Management and QoS Video streams One MPEG-4/WMV stream, one DVD-quality MPEG-2 stream, or one 10Mbps+ high definition stream at 50ft (18m) with simultaneous background traffic Video clients Video streaming to 802.11b clients not supported Traffic Management and QoS Classes of service Voice, Video, Best Effort and Background Number of hardware queues Number of software queues Management Configuration and monitoring interface Ruckus Wireless Web User Interface (WebUI) Username: admin Login Password: Auto configuration Not available in this release Statistics Software update Other Utilities LAN, wireless and associated remote APs Accessible via Ruckus Wireless Web Interface Via FTP, TFTP, or Web download Accessible via Ruckus Wireless Web Interface System Support Snapshot Others Standards/Specifications 802.11 b/g 802.11u 802.11e, Wi-Fi Alliance WMM 802.1x Channels US/Canada: 1-11 Europe (ETSI X30): 1-13 Japan X41: 1-13 RF Power output 17 dBm for 802.11b 20 dBm for 802.11g Certifications FCC, IC-03, CE Wireless Security 802.1x WEP/WPA 52 MF2201 MetroFlex Wireless Access Gateway User’s Guide 8000003, December 2005
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Mode : UseOutlines XMP Toolkit : 3.1-701 Web Statement : http://www.video54.com Producer : Acrobat Distiller 7.0.5 (Windows) Copyright : 2005 Create Date : 2006:01:23 13:22:10Z Creator Tool : FrameMaker 7.0 Modify Date : 2006:01:23 13:22:10Z Format : application/pdf Creator : Video54, Inc. Title : User’s Guide Document ID : uuid:fca3ffb7-fbde-446d-a1a5-ac05f138ae4c Instance ID : uuid:903009c0-0bb5-472d-aac4-1e73cfdaf342 Page Count : 52 Author : Video54, Inc.EXIF Metadata provided by EXIF.tools