Ruckus Wireless R600 R600 Access Point User Manual R600 Quick Setup Guide

Download:
Mirror Download [FCC.gov]
Document ID	2428876
Application ID	caUndrrB3MrpY/tGbFxcMw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.58kB (582229 bits)
Date Submitted	2014-10-27 00:00:00
Date Available	2014-10-27 00:00:00
Creation Date	2007-02-21 14:03:02
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2014-09-10 12:21:01
Document Title	R600 Quick Setup Guide
Document Creator	FrameMaker 11.0.2
Document Author:	Ruckus Wireless, Inc.

•
Software License and Limited Warranty are available at
http://support.ruckuswireless.com/warranty.
PACKAGE CONTENTS
R600 Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions
on how to set up your Ruckus Wireless R600 Dual Band
802.11ac Multimedia Wi-Fi Access Point. After completing
the steps described in this Guide, you will be able to place
the Access Point (AP) at your site and provide wireless
network access to users.
Note: The R600 requires a minimum of ZoneFlex (ZF)
firmware version 9.8.1 or later, or SmartCell Gateway
(SCG) firmware version 2.5.1 or later, or virtual SmartCell
Gateway (vSCG) 3.0 or later.
THIS GUIDE IN OTHER LANGUAGES
•
•
•
•
•
•
R600 Access Point
•
One wall-mount anchor kit, including two 1" No. 8 steel panhead Phillips sheet metal screws, one 5mm M2.5 x 1.06 Torx
security screw, and wall-mount anchors
•
One external T-bar bracket (two unassembled parts)
•
One unit removal pin
•
Regulatory flyer
•
Product warranty statement
•
Declaration of Conformity, if required
•
This Quick Setup Guide
Figure 2: Bottom view
PoE Port
•
A computer running Windows 7 (procedures for other OS’s
are similar)
•
Two Cat 5e Ethernet cables
•
No. 2 Phillips screwdriver and T8 Torx driver for wall mounting anchor kit
•
An AC power adapter (sold separately), or
an 802.3af- or 802.3at-compliant Power over Ethernet
(PoE) switch or PoE injector
•
STEP 3: PREPARE YOUR COMPUTER
SETUP
When mounting the R600 to a truss or pole, two customersupplied cable ties
IMPORTANT! If the AP is deployed with a ZoneDirector, then
refer to the ZoneDirector Quick Setup Guide and connect the
AP to your local network.
STEP 2: CONNECT THE AP
TO
•
Software Upgrades are available at
•
Open Source information is available at
http://opensource.ruckuswireless.com.
Copyright © 2014 Ruckus Wireless, Inc.
Published September 2014, Part Number 800-70633-001 Rev B
On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as follows:
Start > Control Panel > Network and Sharing
Center > Change Adapter Settings
Edit the TCP/IPv4 address settings as follows:
•
Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
The TCP/IPv4 Properties dialog box appears.
Important! Write down all of the currently active settings so
you can restore your computer to its current configuration
later (when this process is complete).
Select Use the following IP address (if it is not already
selected) and then make the following entries:
•
IP address: 192.168.0.22 (or any address in the
192.168.0.x network)
• Subnet mask: 255.255.255.0
• Default gateway: 192.168.0.1
Leave the DNS server fields empty.
http://support.ruckuswireless.com/documents.
http://support.ruckuswireless.com/software.
AP
•
YOUR COMPUTER
Figure 1: Top view
FOR
Note: The following procedures assume Windows 7 as the
operating system. Procedures for other OS’s are similar.
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
User Guides and Release Notes are available at
12VDC Port
MENTS
BEFORE YOU BEGIN
•
Alternatively, connect the PoE port to a PoE injector or
switch for both power and network connections.
Verify that the Power LED on the external enclosure is a
steady green.
STEP 1: COLLECT TOOLS AND SETUP REQUIRE-
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com.
こ の ガ イ ド の日本語版は https://
support.ruckuswireless.com
で ご 覧 く だ さ い。
이 가이드의 한국어 버전은 웹 사이트
(https://support.ruckuswireless.com) 에서 확인하시기 바
랍니다 .
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta
guía en https://support.ruckuswireless.com.
•
Using an AC adapter (sold separately), connect the AP
12VDC port to a protected power source.
After removing your Ruckus Wireless AP from its package, place it next to your computer.
Using an Ethernet cable, connect your computer’s network port to one of the two ports on the AP.
Click OK to save your changes.
Your changes are put into effect immediately.
Page 1 of 4
STEP 4: LOG INTO THE AP
As specified earlier, the AP should be directly connected to
your computer (through one of the Ethernet ports) and
powered on, ready for setup.
On your computer, open a Web browser window.
In the browser, type this URL to connect to the AP:
https://192.168.0.1
Press  to initiate the connection. When a security alert dialog box appears, click OK/Yes to proceed.
When the Ruckus Wireless Admin login page appears,
enter the following:
• Username: super
• Password: sp-admin
Click Login.
STEP 5: CUSTOMIZE
THE
Optional: If You Want To Switch from DHCP (Default):
If you anticipate logging into the AP regularly to perform
monitoring or maintenance once it is in place, you may want
to consider assigning a static IP address to the AP.
In a default AP configuration, the AP uses a DHCPassigned IP address.
A. On the menu, click Configuration > Internet.
B. Click the Static IP option.
C. Fill in the IP Address and Mask fields.
D. Click Update Settings to save your changes.
10 When the Ruckus Wireless Admin login page reappears,
you can exit your browser.
FOR MORE INFORMATION
You can now use the wireless network to log into the AP’s
Web interface. For information on how to configure the AP,
refer to the Ruckus Wireless ZoneFlex Indoor Access Point
User Guide.
(OPTIONAL) MOUNTING INSTRUCTIONS
The R600 can be mounted to a T-bar, wall or ceiling a using
the enclosed mounting kits. Refer to the following sections:
•
•
•
•
Wireless1—Wireless8
(2.4GHz radio)
Wireless9—Wireless16 (5GHz
radio)
STEP 6: PLACE
Use the Mounting Template on the last page of this
Quick Setup Guide as a template to mark the locations
for drill holes on the mounting surface. There are two
sets of keyholes available on the AP. One allows the AP
to be mounted to a wall or ceiling. The other allows the
R600 to be mounted to an accessory bracket (not
included).
AP IN YOUR SITE
Move the AP to its permanent location (accessible to
both power and network connections). Refer to
(Optional) Mounting Instructions for physical installation.
Use an Ethernet cable to connect the PoE port to the
appropriate device:
Use a 5mm drill bit to drill holes approximately 25mm
into the mounting surface (A in Figure 3).
•
•
Insert the anchors and mounting screws into the mounting surface, leaving approximately 1/4” (6 mm) of the
screw heads protruding for the AP enclosure.
Insert the unit removal pin into the hole on the side of
the AP to release the locking mechanism (B in Figure 3).
Place the AP onto the mounting screws so that the screw
heads enter the mounting holes on the AP enclosure,
and push the AP down to lock in place.
Remove the unit removal pin to release the locking
mechanism and secure the AP.
To remove the AP, insert the unit removal pin into the
hole on the side of the AP to unlock, then push the AP up
to release the AP enclosure from the mounting screws.
192.168.0.1
On the Web interface menu, click Configuration >
Radio 2.4G or Configuration > Radio 5G. The
Configure :: Wireless :: Common options appear.
THE
The ISP’s or carrier’s network device
The Ethernet switch that is connected to the ISP’s or
carrier’s network device
Note: If you will be using PoE, then you will need a Cat 5e
(or better) Ethernet cable to connect the AP to the PoE
injector or switch.
Verify that the following options are active:
•
•
Connect the AP power adapter (or PoE power supply) to
the AP, then to a convenient power source.
Channel: SmartSelect
Country Code: If you are not located in the United
States, select your current country.
Click Update Settings if you made any changes.
Click any of the “Wireless #” tabs at the top of the page.
In Wireless Availability, click Enabled.
Delete the text in the SSID field, then type a name for
your network that will help your users identify the AP in
their wireless network connection application.
Using any wireless-enabled computer or mobile device,
search for and select the wireless network you previously
configured.
Click Update Settings to save your changes.
Repeat Steps 4-7 for each Wireless # interface that you
want to enable.
If you can connect, open a browser and link to any public
Web site.
Copyright © 2014 Ruckus Wireless, Inc.
Published September 2014, Part Number 800-70633-001 Rev B
Mounting on a Flat Surface
Mounting on a Recessed Drop-Ceiling T-Bar
Mounting on a Flush Drop-Ceiling T-Bar
Mounting on a Truss or Pole
Mounting on a Flat Surface
WIRELESS SETTINGS
Security (Encryption method) Disabled for each wireless
interface
Default Management IP
Address
Click Logout to exit the Web interface.
11 Disconnect the AP from the computer and from the current power source, and then restore your computer to its
original network connection configuration.
Default AP Settings (For Your Reference)
Network Names (SSIDs)
Verify that the PoE port LED is lit.
After a short pause to re-establish the Internet connection,
you can test the AP.
STEP 7: VERIFY THE INSTALLATION
Figure 3. Flat surface mounting
Congratulations! Your wireless network is active and ready
for use.
Page 2 of 4
Mounting on a Recessed Drop-Ceiling T-Bar
Note: This mounting bracket can also be used on a flush
drop-ceiling T-bar, so the four rubber feet on the bottom
of the AP minimize ceiling tile displacement.
Hold the R600 in place and gently push the locking tab
(B in Figure 5) until its clasp grips the other edge of the Tbar.
CAUTION: Make sure that all three clasps are gripping the Tbar!
Removing an External Bracket from a T-Bar
•
•
•
Insert the unit removal pin (A in Figure 4) into the hole on
the side of the R600 (B in Figure 4) to release the locking
mechanism.
Figure 4. Attaching the external bracket to the AP
•
•
Mounting an AP using the Integrated Bracket
Removing an AP Integrated Bracket from a T-Bar
Mounting an AP using the Integrated Bracket
The enclosed T-bar bracket supports mounting to recessed
drop ceiling T-bars.
Mounting an AP using the External Bracket
Removing an External Bracket from a T-Bar
Removing an External Bracket from an AP
Mounting an AP using the External Bracket
Mounting on a Flush Drop-Ceiling T-Bar
Move the ceiling tiles out of the way.
Gently lift up the locking tab (A in Figure 6) by sliding
your fingers under the tab.
While lifting up on the locking tab, rotate the R600and-T-bar bracket assembly (B in Figure 6). The R600and-T-bar bracket assembly comes away from the Tbar.
Orient the AP so that the T-bar is positioned between
the T-bar clips as shown in Figure 8, then rotate the AP
until the third T-bar clip catches the T-bar and the
latch locks the T-bar in place (Figure 9).
Figure 8. Attaching the integrated bracket to the T-bar
Figure 6. Removing the external bracket from the T-bar
Figure 9. Locking the integrated bracket to the T-bar
Removing an External Bracket from an AP
Position the studs on the bottom of the T-bar bracket (C
in Figure 4) in the mounting holes on the R600 enclosure,
and then slide the T-bar bracket until the studs are in the
narrow parts of the R600 mounting keyholes (arrow).
Remove the unit removal pin (A in Figure 4) to engage
the locking mechanism and secure the T-bar bracket to
the R600.
Make sure that the locking tab (D in Figure 4) is in the
first position on the T-bar bracket (C in Figure 4).
Gently push the ceiling tiles up and out of the way.
Position the T-bar bracket so its two clasps grip one edge
of the T-bar (A in Figure 5). Make sure that both clasps
are gripping the T-bar.
Insert the unit removal pin (A in Figure 7) into the hole
on the side of the R600.
Gently lift up the retainer tab (B in Figure 7).
Gently push the T-bar bracket (C in Figure 7) until it
detaches from the R600.
Figure 7. Removing the external bracket from an AP
Removing an AP Integrated Bracket from a T-Bar
Figure 5. Attaching the external bracket to the T-bar
Copyright © 2014 Ruckus Wireless, Inc.
Published September 2014, Part Number 800-70633-001 Rev B
To remove the AP from a T-bar, first remove the
security screw, then depress the latch while rotating
the AP so that the T-bar clips disengage the T-bar.
Mounting on a Truss or Pole
Insert the Torx security screw into the hole near the
latch to lock the AP in place.
Feed the customer-supplied cable ties through the
two slots on the back of the R600.
Fasten the R600 to the truss or pole using the cable
ties.
Page 3 of 4
Mounting Template
Copyright © 2014 Ruckus Wireless, Inc.
Published September 2014, Part Number 800-70633-001 Rev B
Page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : Ruckus Wireless, Inc.
Create Date                     : 2007:02:21 14:03:02Z
Modify Date                     : 2014:09:10 12:21:01-07:00
Subject                         : R600 Quick Setup
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : FrameMaker 11.0.2
Metadata Date                   : 2014:09:10 12:21:01-07:00
Format                          : application/pdf
Description                     : R600 Quick Setup
Title                           : R600 Quick Setup Guide
Creator                         : Ruckus Wireless, Inc.
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:1329800c-68f1-463e-ba5f-74007e94393a
Instance ID                     : uuid:856493e1-ada7-40af-817a-f2b2e35ba1e3
Page Layout                     : OneColumn
Page Mode                       : UseOutlines
Page Count                      : 4

EXIF Metadata provided by EXIF.tools