Ruckus Wireless ZF7321 ZoneFlex 7321Access Point User Manual
Ruckus Wireless, Inc. ZoneFlex 7321Access Point
Contents
User manual
iRUCkUS“ WIRELESS ZoneFlex 7321 802.11n Multimedia Wi-Fi Access Point Quick Setup Guide This Quick Setip Guide provides step-byestep instructions on how to set up your Ruclrus Wireless ZoneFlex Access Point. Alter completing the steps described in this Guide, you will be able to place the Access Point (AP) at your site and provide wireless network access to users BEFORE You BEGIN Belore deploying Ruckus Wireless products, please checkror the latest software and the release documentation. I User Guides and Release Notes are available at httE'llsupgort.ruckuswireless.com/documents. - Software Upgrades are available at http://support mckuswrreless.corn/software. - Open Source Information Is available at http.//opensource.ruckuswireless.com. 0 Software License and Limited Warranty available at httpj/supgort ruckuswireless com/warrang. PACKAGE CONTENTS 0 ZoneHex 7321 Access Point I Mounting screws and anchors (2) 0 Security screw Regulatory flyer This Ouidt Setup Guide SETUP REOLIREMEN'TS 0 A computer mnning Windows 7 (procedures for other 05‘s are similar) . One or more of the following: I A modern (DSL or cable), broadband router, or other device provided by your Internet Service Provider that brings Internet access to your site. - A network switch or a DSL/lnternet gateway device. - Two Cat Se Ethernet cables 0 An AC power adapter (sold separately), or I An mflaf or $2.3m -cornpliant Power over Ethernet (PoE) switch or PoE injector IMAM“ ll the AP is deployed with a ZoneDirector, folow the ZoneDirecmr Chick Setup Guicb, and connect the AP In your local nebrlrorlc STEP 1: CONNECT THE AP TO YOUR COMPUTER 1 After removing your Ruckus Wireless AP from its pack- age, place it next to your computen 2 Using an Ethernet cable, connect your computer's net work port to the roam/1000 port on the AP. 3 Using the AC adapter (sold separately), connect the AP to a convenient (and protected) power source. - Alternatively, connect the 10/100/1000 port to a PoE injector or PoE switch for both power and network connectivity, .,‘ . if.) “—J —l {li- n -- LIE 9, 4 Verify that the Power LED on the external enclosure is a steady green. Copyright 6 2012 Ruckus \Mreless, Inc, Published March 2012, Part Number m70365-m1 Rev 3 STEP 2: PREPARE YOUR COMPUTQ FOR AP SETUP NOTE: The following procedures assume Mndows 7 as the operating system. Procedures for other 05‘: are similan 1 On yourWindows 7 computer, Configure your network adapter from the Local Area Connecfion settings as follows: 0 Start>CcntmlPawl>NetworkandShafing Center > Change Adapter Settings 2 Edit the TCP/va4 address settings as follows: 0 Local Area Connection > Properties > Internet Protocol Version 4 (T CP/IM) > Properties The TCP/lPl/4 Properties dialog box appears. WANT! Write down all otthe currently active settings so you can restore your computer to its current configuration later (when this process Escorrplete), 3 Select Use the following IP address (if it is not already selected) and then make the following entries: 0 IP adios: 191168.012 (or any address in the 191168.01 network) . Subnet mask: 255.255.2550 - Default gateway: 192,168.01 Leave the DNS server fields empty. 4 Click OK to save your changes, Your changes are put into ellect immediately. STEP 3: LOG INTO THE AP As specified earlier, the AP should be directly connected to your computer (through the Ethernet port) and powered on, ready lor setup. 1 On your computer open aWeb browser window. 2 In the browser, type this URL to connect to the AP: lumped/191168.04 3 Pressto initiate the connection. When a security alert dialog box appears, click OK/Yes to proceed. ‘ when the Ruckus Wireless Admin login page appears, enter the following; - Usemarne: super - Password: sp—admin 5 Click Login. Default AP Settings (For You Reform) Network Names [SSIDS) Security (Encryption Dsabled for each wireless interrace method) WirelessI—Wirelessa (2.4GHz radio) Default IVZJMDJ 4 Verily that the lO/lWlalJ port LED is lit. After a short pause to reestablish the Internet connection, you can test the AP. STEP 6: VERIFY THE INSTALLATION 1 Using any wireless-enabled computer or mobile device, search for and select the wireless network you previously configrred. Management IP Address I On the Web Interface menu, dick Configuati less. The Configure :2Wirele§ :: Common optic 2 Verity that the following options are active: I Channel: SmartSelect - Col-my C060: II you are not located in States, select your current country. Click Update Settings ifyou made any chan 4 Click any of the eight 'Wireless ll" tabs at the page- 5 ln Wreless Availability, click EM. 6 Delete the text in the SSID field, and then for your network that will help your users iden in their wireless network connection applicati 1 Click Update Settings to save your changes 0 Repeat Steps u (or each Wireless ll intertac that ya want to enable. 9 dick Logout to exit the Web interface. 10 Disconnect the AP from the compumr and the cur- rent power source, and then restore your corn uter to its original network connection configuration. to STEP 5: PLACE THE AP IN YOUR SITE . 1 Move the AP to its permanent location (accessble‘lqpath AC power and network connection). 7 ‘ Z Use an Ethernet cable to connectthe 10/1le port of the AP to your network. ' on Die releaset meEfiams . MTEIfyouwillbeusing PoEyouwillneedaCetSebr better) EthematcabletooonnecttheAPhthePoE injec- tic-rotswitch. 3 Connect the AC power adapter (or PoE power supply) to the AP, then In a convenient power source. 2 ltyou can connect, open a browser and link to any public Web site. Congratulations! Your wireless network is active and ready for use. ltyou need to configure advanced wireless settings, such as enabling security, see the AP User Guide. (OPTIONAL) MOUNTING INSTRUCTIONS The ZoneFlex 7321 can be mounted to aceiling or to a T—bar using the supplied mounting screws or the T—bar clips built into the bottom of the AP enclosure. Mounting to a Hat Surtace 1 Use this Ouidr Sort Guide terrplate to marl: the loc bus for screw holes on the mounting surface. The AP ma alter- natively be mounted to a NEMA standard electrical nction box. 2 Insert the mounting screws into the mounting leaving approximately 1/4' (6 mm) of the s protruding for the AP enclosure. The screws approximately 3.25‘ (82.6mm) apart per the te 3 Insert a straightened paperclip (or similar) into h hole on the side olthe AP (top left corner, when th is one ented with the Ethernet ports at the bottom), 4 Place the AP dnto the mounting screws so that the screw heads enter the mounting holes on the AP enclosure, and push the AP (to the left or down depending on ori- entation) to lock in place. 5 Remove the paperclip to release the led: mechanism and secure the AP. 6 Tounmoun insertastrai htened a cli intothehole on the side ofthe AP to unlock, then push the AP (to the right or up, depending on orientation) to release the AP enclosure from the mounting screws. Mounting to a 118: 1 Orient the AP so that the Tabar is positioned between the T—bar clips as shown in Figure 1, then rotate the AP until the third T-bar clip catches the T-bar and the latch lodcs the T-bar in place (Figure 2). Copyright 6 2012 ltuckusvwreleas Inc. Pubrrshed Mald't 2011 Part Number 50070365001 Rev 9 Fi re 2. 2 Insert the security screw into the hole near the latch to ock in place. 3 To remove the unit, first remove the security screw, then depress the latch while rotating the AP so that the T-bar clips disengage the T-bar MORE INFORMATION Yo can now use the wireless network to log into the APs W, interface. Use the Web interface to review and finer who a wide range of AP settings. For information on how to —' ’conligure the AP from the Web interface, refer to the Ruckus Wireless ZoneFlex Access Point User Guide or the Online Help, available from within the Web interface.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2012:04:06 12:04:50-07:00 Creator : Adobe Acrobat 10.1.2 Modify Date : 2012:04:06 12:04:50-07:00 Title : XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2012:04:06 12:04:50-07:00 Creator Tool : Adobe Acrobat 10.1.2 Format : application/pdf Document ID : uuid:33d585a7-9e65-42f3-b0c6-5bb0f5c427df Instance ID : uuid:baa053d9-529f-4705-959d-324cfea12b5b Producer : Adobe Acrobat 10.1.2 Image Conversion Plug-in Page Count : 2EXIF Metadata provided by EXIF.tools