Ruckus ICX Switch Quick Start Guide 7150/7250/7450 (QSG) Brocade Qsg
Ruckus ICX Switch 7150/7250/7450 Quick Start Guide (QSG) brocade-icx-switch-qsg
2017-06-15
User Manual: Ruckus Ruckus ICX Switch 7150/7250/7450 Quick Start Guide (QSG)
Open the PDF directly: View PDF .
Page Count: 10
Download | |
Open PDF In Browser | View PDF |
QUICK START GUIDE Ruckus ICX Switch Quick Start Guide Supporting the Ruckus ICX 7150, ICX 7250, and ICX 7450 families of Ethernet switches 53-1004910-02 15 March 2017 © 2017, Brocade Communications Systems, Inc. All Rights Reserved. Brocade, the B-wing symbol, and MyBrocade are registered trademarks of Brocade Communications Systems, Inc., in the United States and in other countries. Other brands, product names, or service names mentioned of Brocade Communications Systems, Inc. are listed at www.brocade.com/en/legal/ brocade-Legal-intellectual-property/brocade-legal-trademarks.html. Other marks may belong to third parties. Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government. The authors and Brocade Communications Systems, Inc. assume no liability or responsibility to any person or entity with respect to the accuracy of this document or any loss, cost, liability, or damages arising from the information contained herein or the computer programs that accompany it. The product described by this document may contain open source software covered by the GNU General Public License or other open source license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd. 2 Ruckus ICX Switch Quick Start Guide 53-1004910-02 Contents About Brocade.....................................................................................................................................................................................................................4 Overview............................................................................................................................................................................................................................... 4 Connecting to the Console................................................................................................................................................................................................4 Telnet............................................................................................................................................................................................................................................................... 4 Serial................................................................................................................................................................................................................................................................ 4 Introduction to the CLI....................................................................................................................................................................................................... 5 Accessing the CLI...................................................................................................................................................................................................................................... 5 Saving the Configuration.........................................................................................................................................................................................................................6 Securing the Web, Serial, and Telnet Interfaces........................................................................................................................................................... 7 Adding a Static IP Address via the CLI...........................................................................................................................................................................8 Accessing the Web GUI .................................................................................................................................................................................................... 8 Creating Additional Web Interface Users..........................................................................................................................................................................................8 Deleting the Default Username and Password..............................................................................................................................................................................8 Saving Configuration Changes.........................................................................................................................................................................................9 Documentation.................................................................................................................................................................................................................... 9 Web Interface User Guide.......................................................................................................................................................................................................................9 CLI Command Reference.......................................................................................................................................................................................................................9 Additional Information.....................................................................................................................................................................................................10 Accessing MyBrocade.......................................................................................................................................................................................................................... 10 Obtaining Software Updates.............................................................................................................................................................................................................. 10 Lifetime Warranty Hardware Replacement...................................................................................................................................................................................10 Ruckus ICX Switch Quick Start Guide 53-1004910-02 3 About Brocade Brocade® (NASDAQ: BRCD) networking solutions help the world's leading organizations transition smoothly to a world where applications and information reside anywhere. This vision is designed to deliver key business benefits such as unmatched simplicity, non-stop networking, application optimization, and investment protection. Innovative Ethernet and storage networking solutions for data center, campus, and service provider networks help reduce complexity and cost while enabling virtualization and cloud computing to increase business agility. To help ensure a complete solution, Brocade partners with world-class IT companies and provides comprehensive education, support, and professional services offerings (www.brocade.com). Overview Direct management of Brocade switches can be performed either via a command-line interface (CLI) or via a web GUI. By default, only the CLI is enabled. This guide explains how to access the CLI, enable the web GUI, and secure all configuration access methods. The web GUI allows full configuration and monitoring of Layer 2 functions, QoS, ACL, authentication, PoE, performing software updates, and much more. Connecting to the Console There are two ways to connect to the configuration console of a new Ruckus ICX switch: either via a Telnet session over an IP network or directly via the serial interface. Telnet If a Ruckus ICX switch is connected to a network, it will automatically issue DHCP requests for an IP configuration, which will be provided by a DHCP server. Identifying the IP address that has been assigned to the switch can be done by viewing the address assignment list on the DHCP server or by the switch serial interface (command: show ip). Once the IP address of the switch is known, a Telnet session can be established using a terminal emulation program. See Accessing the CLI on page 5. Serial Ruckus ICX 7150 The Ruckus ICX 7150 presents a USB Type-C connection, which can be connected directly to the USB port on a PC using a standard USB cable. Any standard USB Type-C–to–Type-A cable can be used; if you wish to purchase the cable from Brocade, the part number is CC-USBC-USBA. The Ruckus ICX 7150 also presents a standard serial interface via an RJ45 connector. If required, an RJ45-to-DB9F cable can be ordered from Brocade using part number CC-RJ45-DB9, which is comprised of the following two parts: • RJ45 to RJ45: Part number 50-1000117-01 • RJ45 to DB9F: Part number 50-0000112-01 Details of the pin allocations of the serial cable are available in the Ruckus ICX 7150 Switch Hardware Installation Guide. Ruckus ICX 7250 and Ruckus ICX 7450 4 Ruckus ICX Switch Quick Start Guide 53-1004910-02 Introduction to the CLI The Ruckus ICX 7250 and ICX 7450 switches present their serial interface via a mini-USB type connector, and every switch is shipped with a serial cable that terminates on both RJ45 and DB9 connections. The two parts shipped with every switch are: • Mini-USB to RJ45: Part number 50-1000122-01 • RJ45 to DB9F: Part number 50-0000112-01 If required, these two parts can be ordered using part number CC-miniusb-RJ45. To connect a PC to the serial interface, a DB9M-to-USB adaptor is required; this adaptor can be obtained from any online electronics supplier. FIGURE 1 DB9M-to-USB Adaptor Once a serial connection to the switch has been made, a terminal emulation program can be used to access the CLI. See Accessing the CLI on page 5. Introduction to the CLI Accessing the CLI Once a network or physical connection has been made to the switch, a command-line interface (CLI) session can be initiated via a terminal emulation program such as PuTTY (www.putty.org). When PuTTY is started, use the following settings depending on whether you are connecting via Telnet or a serial interface: FIGURE 2 PuTTY Telnet Settings Ruckus ICX Switch Quick Start Guide 53-1004910-02 5 Introduction to the CLI FIGURE 3 PuTTY Serial Settings (xx is the number of the COM port, e.g. COM5) Once connected to the switch, the interface will present a console prompt. There are three privilege levels that are used to configure and manage a switch: user EXEC mode, privileged EXEC mode, and global configuration mode. User EXEC Mode The user is able to perform basic commands to display the status and configuration of the device. device> Privileged EXEC Mode At this level, the user can perform tasks such as saving the configuration, updating firmware, and performing other administrative tasks. device> device> enable device# Note that the enable command can be shortened to ena. Global Configuration Mode This is the highest level and allows the user to make configuration changes. device> device> enable device# configure terminal device(config)# Note that the configure terminal command can be shortened to conf t. From any prompt, the available commands can be listed by entering a question mark (?). Prompts can be auto-completed using the Tab key. The options available at any level can be listed by entering ? or pressing Tab. For example: device> device> … device> device>device> … sh show show ver show version show version The exit command is used to drop back to the next lowest command level. Saving the Configuration Any configuration changes made using the CLI should be saved using the write memory command, which can be shortened to wr mem. device> ena device# wr mem 6 Ruckus ICX Switch Quick Start Guide 53-1004910-02 Securing the Web, Serial, and Telnet Interfaces Write startup-config done. Copy Done. device# Securing the Web, Serial, and Telnet Interfaces The following commands enable web access and secure the web GUI, serial, and Telnet interfaces with a default username and password of your choice. device> ena device# conf t device(config)# device(config)# device(config)# device(config)# device(config # device(config # device(config)# device(config)# device(config)# device(config)# device# crypto-ssl certificate generate username password aaa authentication login default local aaa authentication web-server default local enable telnet authentication enable aaa console web-management https password-change any wr mem exit Make sure that the username and password are secure and easy to remember. Once set, access to the CLI and web interface will be possible only when the password has been correctly entered. IMPORTANT For reasons of security, Ruckus ICX switches do not provide any remote back-door access or reset mechanisms for the CLI or web passwords. For details on resetting a lost password, refer to the hardware installation guide. The password can be changed by repeating the username password command or via the web interface under Configure > System > Management > User Account. Cut and paste the following command set at the user EXEC prompt to apply the complete configuration outlined above and set a default username of brocade with a password of brocade. enable configure terminal crypto-ssl certificate generate username brocade password brocade aaa authentication login default local aaa authentication web-server default local enable telnet authentication enable aaa console web-management https password-change any write memory exit TIP In PuTTY, use the right button on the mouse to paste text at the console prompt. Access to the web interface is now possible, and all access methods are protected by a username and password. IMPORTANT To ensure that your switches are secure from unauthorized access, always set a secure password. Never leave a switch with the default brocade/brocade settings provided above. Ruckus ICX Switch Quick Start Guide 53-1004910-02 7 Adding a Static IP Address via the CLI Adding a Static IP Address via the CLI If you wish to add a static IP address to the switch before using the GUI, you can do so easily from the CLI using the following commands. device> ena device# conf t device(config)# device(config)# device(config)# device(config)# device# ip address ip default-gateway wr mem exit NOTE When setting the IP address, the syntax /mask> is also permitted; for example, 192.168.1.10/24. NOTE The commands listed above are applicable to Ruckus ICX switches running Layer 2 switch code that is the factory default for the Ruckus ICX 7150, Ruckus ICX 7250, and Ruckus ICX 7450. Accessing the Web GUI You can now access the web interface of the switch. Enter the IP address of the switch into the address bar using either HTTP or HTTPS; for example, https://192.168.2.79/. Creating Additional Web Interface Users The first task should be to create usernames and passwords to secure access to the switch. This is done via the User Account page, which can be found under Configure > System > Management > User Account. Users can be created with one of three permission levels: 0 Read-Write Full read-write access for all system parameters. 4 Port-Config Read-write access for specific ports, but not for global system parameters. 5 Read-Only Read-only access for configuration and system parameters. Deleting the Default Username and Password If the brocade/brocade default username and password were used for the initial configuration, these must be deleted to protect the system. Once you have created a new Read-Write user, simply delete the brocade/brocade user and save the configuration. 8 Ruckus ICX Switch Quick Start Guide 53-1004910-02 Documentation Saving Configuration Changes Changes made to the configuration are not automatically saved during a session. An option to save changes is provided when logging out of the web interface. To save the configuration manually, use the Save to Flash option under the Command menu. Documentation All documentation for Brocade/Ruckus campus switches can be found in the document page for each product: http:// www.brocade.com/en/products-services/switches/campus-network-switches.html. Web Interface User Guide The Brocade FastIron Web Management Interface User Guide is available at http://www.brocade.com/content/html/en/fastiron-os/ 08-0-60/fastiron-08060-webguide/index.html. CLI Command Reference The Brocade FastIron Command Reference Guide documents all of the available commands: www.brocade.com/content/html/en/fastiron-os/08-0-60/fastiron-08060-commandref/ Ruckus ICX Switch Quick Start Guide 53-1004910-02 9 Additional Information Additional Information Accessing MyBrocade MyBrocade provides access to all product documentation, software updates, technical assistance resources, and Brocade communities. To register for MyBrocade, go to https://my.brocade.com/. To access the full range of services, register your products by going to your profile and clicking Get Support Access. Alternatively, use the Warranty Product Registration form to register your products: http://www.brocade.com/en/forms/warranty-registration.html. Obtaining Software Updates Access to software updates is available via MyBrocade. To access switch software, register your products by going to your profile and clicking Get Support Access. Lifetime Warranty Hardware Replacement All Ruckus ICX switches include a lifetime hardware replacement warranty. Full details are available at http://www.brocade.com/en/ support/warranties-and-returns.html. 10 Ruckus ICX Switch Quick Start Guide 53-1004910-02
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Brocade Communications Systems, Inc. Create Date : 2017:03:15 13:38:18-08:00 Modify Date : 2017:03:15 13:42:22-07:00 Language : EN-US XMP Toolkit : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08 Format : application/pdf Creator : Brocade Communications Systems, Inc. Title : Ruckus ICX Switch Quick Start Guide Creator Tool : AH XSL Formatter V6.2 MR12 for Windows (x64) : 6.2.14.22278 (2015/10/30 10:00JST) Metadata Date : 2017:03:15 13:42:22-07:00 Producer : Antenna House PDF Output Library 6.2.726 (Windows (x64)) Trapped : False Document ID : uuid:2264266e-e397-4db3-a3f3-392147ccd19b Instance ID : uuid:605bb3ce-2405-45fd-8ddc-3e32498f8e2b Page Mode : UseOutlines Page Count : 10EXIF Metadata provided by EXIF.tools