Ruckus Brocade FastIron WS Hardware Installation Guide Fast Iron Series Installguide

FastIron WS Series Hardware Installation Guide fastiron-ws-installguide

2017-07-07

User Manual: Ruckus FastIron WS Series Hardware Installation Guide

Open the PDF directly: View PDF PDF.
Page Count: 74

Part Number: 53-1002498-03
Publication Date: 15 June 2017
Brocade FastIron WS Hardware Installation
Guide
HARDWARE INSTALLATION GUIDE
Copyright © 2017, Brocade Communications Systems, Inc. All Rights Reserved.
Brocade, Brocade Assurance, the B-wing symbol, ClearLink, DCX, Fabric OS, HyperEdge, ICX, MLX, MyBrocade, OpenScript, VCS, VDX, Vplane, and
Vyatta are registered trademarks, and Fabric Vision is a trademark of Brocade Communications Systems, Inc., in the United States and/or in other
countries. Other brands, products, or service names mentioned may be trademarks of others.
Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment
feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and
assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office
for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States
government.
The authors and Brocade Communications Systems, Inc. assume no liability or responsibility to any person or entity with respect to the accuracy of this
document or any loss, cost, liability, or damages arising from the information contained herein or the computer programs that accompany it.
The product described by this document may contain open source software covered by the GNU General Public License or other open source license
agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and
obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd.
Brocade FastIron WS Hardware Installation Guide 3
Part Number: 53-1002498-03
Contents
Preface
Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Text formatting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Command syntax conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Notes, cautions, and danger notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Brocade Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Contacting Brocade Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
About This Document
Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Product Overview
Hardware features
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FWS624, FWS648,
FWS624G,
FWS648G
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FWS624-POE, FWS648-POE, FWS624G-POE,
FWS648G-POE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Control features
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SFP Network interfaces
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power supplies
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing FWS624 and FWS648 Models
Unpacking the device
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Package contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
General requirements
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Summary of installation tasks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation precautions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
General precautions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lifting precautions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power precautions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Preparing the installation site
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cabling infrastructure
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation location
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the device
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Desktop installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Rack mount installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installing a redundant power supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RPS2-EIF Redundant Power Supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RPS12 external redundant power supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selecting a redundant power supply installation site
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Equipment checklist
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Mounting a redundant power supply in a rack
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Connecting devices to the redundant power supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Port pin-out diagram for the RPS2-EIF power supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Port pin-out diagram for the RPS12 power supply
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Activating power to the device
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Verifying proper operation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Attaching a PC or terminal
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Connecting Network Devices and Checking Connectivity
Assigning permanent passwords
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Recovering from a lost password
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Configuring IP addresses
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Devices running layer 2 software
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Devices running layer 3 software
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connecting network devices
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Connectors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cable specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Connecting to Ethernet or Fast Ethernet Hubs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Connecting to workstations, servers, or routers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Connecting a network device to a fiber port
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Testing connectivity
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Pinging an IP address
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Observing LEDs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Tracing a route
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Troubleshooting network connections
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Using Virtual Cable Testing to diagnose a cable
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Digital Optical Monitoring
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Managing the FastIron WS Hardware
Managing FastIron WS temperature settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Removing MAC address entries
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Displaying CPU usage
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Hardware maintenance schedule
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Replacing a fiber optic module
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Removing a fiber optic module
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Installing a new fiber optic module
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Cabling a fiber optic module
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Cleaning the fiber-optic connectors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Hardware Specifications
Hardware specifications for FastIron WS models
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Physical dimensions and weight
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Environmental considerations
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Cooling system and fans
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Pinouts and signalling
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Cable specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Power cords
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
AC power supply specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Power specifications for POE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Troubleshooting
Diagnosing switch indicators
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Power and cooling problems
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
In-band access
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Brocade FastIron WS Hardware Installation Guide 5
Part Number: 53-1002498-03
Regulatory Statements
USA (FCC CFR 47 part 15 warning)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Industry Canada statement
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Europe and Australia (CISPR 22 class A warning)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Japan (VCCI)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Japan power cord
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Korea
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Russia
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
China
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
BSMI statement (Taiwan)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Regulatory compliance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Caution and Danger Notices
Cautions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Danger
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Brocade FastIron WS Hardware Installation Guide 7
Part Number: 53-1002498-03
Preface
•
Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
•
Brocade resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
•
Contacting Brocade Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
•
Document feedback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Document conventions
The document conventions describe text formatting conventions, command syntax conventions, and important notice formats used in
Brocade technical documentation.
Text formatting conventions
Text formatting conventions such as boldface, italic, or Courier font may be used in the flow of the text to highlight specific words or
phrases.
Command syntax conventions
Bold and italic text identify command syntax components. Delimiters and operators define groupings of parameters and their logical
relationships.
Format Description
bold text Identifies command names
Identifies keywords and operands
Identifies the names of user-manipulated GUI elements
Identifies text to enter at the GUI
italic text Identifies emphasis
Identifies variables
Identifies document titles
Courier font
Identifies CLI output
Identifies command syntax examples
Convention Description
bold text Identifies command names, keywords, and command options.
italic text Identifies a variable.
value In Fibre Channel products, a fixed value provided as input to a command option is
printed in plain text, for example, --show WWN.
[ ] Syntax components displayed within square brackets are optional.
Default responses to system prompts are enclosed in square brackets.
8Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Preface
Brocade resources
Notes, cautions, and warnings
Notes, cautions, and warning statements may be used in this document. They are listed in the order of increasing severity of potential
hazards.
NOTE
A Note provides a tip, guidance, or advice, emphasizes important information, or provides a reference to related information.
ATTENTION
An Attention statement indicates a stronger note, for example, to alert you when traffic might be interrupted or the device might
reboot.
Brocade resources
Visit the Brocade website to locate related documentation for your product and additional Brocade resources.
You can download additional publications supporting your product at www.brocade.com. Select the Brocade Products tab to locate your
product, then click the Brocade product name or image to open the individual product page. The user manuals are available in the
resources module at the bottom of the page under the Documentation category.
To get up-to-the-minute information on Brocade products and resources, go to MyBrocade. You can register at no cost to obtain a user
ID and password.
Release notes are available on MyBrocade under Product Downloads.
White papers, online demonstrations, and data sheets are available through the Brocade website.
{ x | y | z } A choice of required parameters is enclosed in curly brackets separated by
vertical bars. You must select one of the options.
In Fibre Channel products, square brackets may be used instead for this purpose.
x | yA vertical bar separates mutually exclusive elements.
< > Nonprinting characters, for example, passwords, are enclosed in angle brackets.
... Repeat the previous element, for example, member[member...].
\ Indicates a “soft” line break in command examples. If a backslash separates two
lines of a command input, enter the entire command at the prompt without the
backslash.
CAUTION
A Caution statement alerts you to situations that can be potentially hazardous to you or cause damage to hardware, firmware,
software, or data.
DANGER
A Danger statement indicates conditions or situations that can be potentially lethal or extremely hazardous to you. Safety
labels are also attached directly to products to warn of these conditions or situations.
Brocade FastIron WS Hardware Installation Guide 9
Part Number: 53-1002498-03
Preface
Contacting Brocade Technical Support
Contacting Brocade Technical Support
As a Brocade customer, you can contact Brocade Technical Support 24x7 online, by telephone, or by e-mail. Brocade OEM customers
contact their OEM/Solutions provider.
Brocade customers
For product support information and the latest information on contacting the Technical Assistance Center, go to
http://www.brocade.com/services-support/index.html.
If you have purchased Brocade product support directly from Brocade, use one of the following methods to contact the Brocade
Technical Assistance Center 24x7.
Brocade OEM customers
If you have purchased Brocade product support from a Brocade OEM/Solution Provider, contact your OEM/Solution Provider for all of
your product support needs.
•
OEM/Solution Providers are trained and certified by Brocade to support Brocade® products.
•
Brocade provides backline support for issues that cannot be resolved by the OEM/Solution Provider.
•
Brocade Supplemental Support augments your existing OEM support contract, providing direct access to Brocade expertise.
For more information, contact Brocade or your OEM.
•
For questions regarding service levels and response times, contact your OEM/Solution Provider.
Document feedback
To send feedback and report errors in the documentation you can use the feedback form posted with the document or you can e-mail the
documentation team.
Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and completeness of this document.
However, if you find an error or an omission, or you think that a topic needs further development, we want to hear from you. You can
provide feedback in two ways:
•
Through the online feedback form in the HTML documents posted on www.brocade.com.
•
By sending your feedback to documentation@brocade.com.
Provide the publication title, part number, and as much detail as possible, including the topic heading and page number if applicable, as
well as your suggestions for improvement.
Online Telephone E-mail
Preferred method of contact for nonurgent
issues:
•
My Cases through MyBrocade
•
Software downloads and licensing tools
•
Knowledge Base
Required for Sev 1-Critical and Sev
2-High issues:
•
Continental US: 1-800-752-8061
•
Europe, Middle East, Africa, and Asia Pacific:
+800-AT FIBREE (+800 28 34 27 33)
•
For areas unable to access toll free number:
+1-408-333-6061
•
Toll-free numbers are available in many countries.
support@brocade.com
Please include:
•
Problem summary
•
Serial number
•
Installation details
•
Environment description
10 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Preface
Document feedback
Brocade FastIron WS Hardware Installation Guide 11
Part Number: 53-1002498-03
About this Document
•
What’s new in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
What’s new in this document
There is no enhancements in this edition.
12 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
About this Document
What’s new in this document
Brocade FastIron WS Hardware Installation Guide 13
Part Number: 53-1002498-03
Product Overview
Hardware features
The FastIron WS Series includes the following models:
•
FWS624
•
FWS648
•
FWS624G
•
FWS648G
•
FWS624-POE
•
FWS648-POE
•
FWS624G-POE
•
FWS648G-POE
These models support an optional external redundant AC power supply that can power up to four units.
The following sections describe the physical characteristics of the FastIron WS models. For more details about physical dimensions,
power supply specifications, and pinouts, refer to <Link>Chapter 5, “Hardware Specifications”.
FWS624, FWS648, FWS624G, FWS648G
FastIron WS devices provide high 10/100 Mbps port density and Gigabit Ethernet uplinks in a compact form factor:
•
FastIron WS624 includes 20 x 10/100 Mbps ports plus 4 Combo 10/100/1000 Mbps copper (RJ45) or 100/1000
Ethernet Fiber (SFP) ports.
•
FastIron WS648 includes 44 x 10/100 Mbps ports plus 4 Combo 10/100/1000 Mbps copper (RJ45) or 100/1000
Ethernet Fiber (SFP) ports.
•
FastIron WS624G includes 20 x 10/100/1000 Mbps ports plus 4 Combo 10/100/1000 Mbps copper (RJ45) or 100/1000
Ethernet Fiber (SFP) ports.
•
FastIron WS648G includes 44 x 10/100/1000 Mbps ports plus 4 Combo 10/100/1000 Mbps copper (RJ45) or 100/1000
Ethernet Fiber (SFP) ports.
The following figures show the front and rear panels of the FastIron WS models.
FIGURE 1 FWS624, FWS624G
14 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Product Overview
Hardware features
FIGURE 2 FWS648, FWS648G
FIGURE 3 FWS624, FWS648, FWS624G, FWS648G rear panel
FWS624-POE, FWS648-POE, FWS624G-POE, FWS648G-POE
FastIron WS POE devices provide high 10/100 port density and Gigabit Ethernet uplinks in a compact form factor:
•
FastIron WS624-POE includes 20 x 10/100 Mbps PoE ports plus 4 Combo 10/100/1000 Mbps copper (RJ45 PoE) or
100/1000 Ethernet Fiber (SFP) ports. Unit supports 802.3af PoE.
•
FastIron WS648-POE includes 44 x 10/100 Mbps PoE ports plus 4 Combo 10/100/1000 Mbps copper (RJ45 PoE) or
100/1000 Ethernet Fiber (SFP) ports. Unit supports 802.3af PoE.
•
FastIron WS624G-POE includes 20 x 10/100/1000 Mbps PoE ports plus 4 Combo 10/100/1000 Mbps copper (RJ45
PoE) or 100/1000 Ethernet Fiber (SFP) ports. Unit supports 802.3af PoE.
•
FastIron WS648G-POE includes 44 x 10/100/1000 Mbps PoE ports plus 4 Combo 10/100/1000 Mbps copper (RJ45
PoE) or 100/1000 Ethernet Fiber (SFP) ports. Unit supports 802.3af PoE.
The following figures show the front and rear panels of these FastIron WS models.
FIGURE 4 FWS624-POE, FWS624G-POE
FIGURE 5 FWS648-POE, FWS648G-POE
100 240 V~
50 60 Hz, 2A 12V ,10A
Brocade FastIron WS Hardware Installation Guide 15
Part Number: 53-1002498-03
Product Overview
Hardware features
FIGURE 6 FWS624-POE, FWS648-POE, FWS624G-POE, FWS648G-POE rear panel
Control features
Serial management interface (console port)
The serial management interface allows you to configure and manage the device using a third-party terminal emulation application on a
directly connected PC. A straight-through EIA/TIA DB-9 serial cable (M or F) ships with the device. The serial management interface
(the console port) is located in the left corner of the front panel.
POE applications
FWS POE devices provide Power over Ethernet (POE), compliant with the standards described in the IEEE 802.3af specification for
delivering in-line power. The 802.3af specification defines the standard for delivering power over existing network cabling infrastructure,
offering multicast-enabled full streaming audio and video applications for converged services, such as Voice over IP (VoIP), WLAN
access points, IP surveillance cameras, and other IP technology devices.
POE technology eliminates the need for an electrical outlet and dedicated UPS near IP powered devices. With power sourcing devices,
such as the Brocade FWS624-POE and FWS648-POE, power is consolidated and centralized in the wiring closets, improving the
reliability and resiliency of the network. Because POE can provide power over Ethernet cable, power is continuous, even in the event of a
power failure.
For more information about POE and how to configure it on FWS devices, refer to the <Italic>FastIron Configuration Guide.
FastIron WS network interfaces
FWS624 and FWS648 devices provide the following interfaces:
•
10/100 Mbpsports with RJ-45 copper connectors (Ports 5~24 or Ports 5~48)
•
10/100/1000 RJ-45 or 100/1000 SFP (1-GE) combo ports (Ports 1~4)
FWS624G and FWS648G devices provide the following interfaces:
•
10/100/1000 Mbps ports with RJ-45 copper connectors (Ports 5~24 or Ports 5~48)
•
10/100/1000 RJ-45 or 100/1000 SFP (1-GE) combo ports (Ports 1~4)
FastIron WS 10/100/1000 BASE-T ports
These devices contain 24/48 RJ-45 ports that operate at 10 Mbps or 100 Mbps, half or full duplex, or at 1000 Mbps, full duplex.
Because all ports support automatic MDI or MDI-X operation, you can use straight-through cables for all network connections to PCs or
servers, or to other switches or hubs. (See <Link>“Pinouts and signalling” on page 49.) Brocade recommends using MDIX cable for
switch-to-switch connections.
Because each port supports auto-negotiation, the optimum transmission mode (half or full duplex), and data rate (10, 100, or 1000
Mbps) can be selected automatically. If a device connected to one of these ports does not support auto-negotiation, the communication
mode of that port can be configured manually.
54V , 8.2A
+12V , 10 A
100 240 V~ , 50 60 Hz , 10A
16 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Product Overview
Hardware features
Combination Ports
FWS devices contain four Small Form Factor Pluggable (SFP) combination ports (ports 1~4), that are shared with four of the RJ45 ports
In the default configuration. If an SFP transceiver is installed in a slot and has a valid link on its port, the associated RJ45 port is disabled
and cannot be used.
SFP network interfaces
Table 1 describes the network interfaces supported on the device. For network interface specifications, refer to the table <Link>“Cable
length summary table” on page 51.
Port and system status LEDs
FWS devices include an LED display panel on the front panel with indicators for key system and port indications to simplify installation
and network troubleshooting. The LEDs are shown in Figure 7 and Figure 8, and described in Table 2 and Table 3.
FIGURE 7 Port status LEDs
TABLE 1 Supported SFP network interfaces for FWS devices
Interface Show media description
1000Base-BX-D M-GBXD
1000Base-BX-U M-GBXU
1000Base-LHA M-LHA
1000Base-LHB M-LHB
1000Base-LX M-LX
1000Base-LH M-LH
1000Base-SX M-SX
1000Base-SX2 M-SX2
1000Base-T C
100Base-BX M-FBX
100Base-FX M-FX
1310-MMF 10GbE 1310-NM
1 Port status LEDs 2 Port status LEDs
TABLE 2 Port status LEDs
LED Status Status
Link or
Activity or Speed
(1-24/48)
SFP(1-4)
On or Flashing Amber Port has a valid link at 10 or 100 Mbps. Flashing indicates activity.
On or Flashing Green Port has a valid link at 1000 Mbps. Flashing indicates activity.
Off The link is down.
12
Brocade FastIron WS Hardware Installation Guide 17
Part Number: 53-1002498-03
Product Overview
Hardware features
FIGURE 8 System status LEDs
Power supplies
Optional redundant power supply
FWS devices support an optional redundant power supply (RPS), that can provide power to the switch in the event the internal power
supply fails.
Power supply receptacles
There are two power receptacles on the rear panel of each switch. The standard power receptacle is for the AC power cord. The receptacle
labeled “RPS” is for the optional redundant power supply cord.
2System status LEDs
TABLE 3 System status LEDs
LED Condition Status
Power Green Internal power is operating normally.
Amber Internal power supply fault.
Off Power off or failure.
Stack Off System stand alone
Green System in stacking master mode
Amber System in stacking slave mode
RPS Green Redundant power supply is providing power.
Amber Primary power supply is active, RPS is on standby.
Off Redundant power supply is off or not plugged in.
POE Green POE module is operating normally.
Amber POE module fault.
Off POE module not present.
2
18 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Product Overview
Hardware features
FIGURE 9 Power supply receptacles
FIGURE 10 Power supply receptacles (POE Models)
1 Power socket 2 Redundant power socket
1 Power socket 2 Redundant power socket
12
12
Brocade FastIron WS Hardware Installation Guide 19
Part Number: 53-1002498-03
Installing FWS624 and FWS648
Models
Unpacking the device
NOTE
The procedures in this manual are intended for qualified service personnel.
NOTE
Before beginning the installation, refer to the precautions in “Power precautions” on page 21. This chapter describes how to
physically install the FastIron WS.
Information about configuring IP addresses and connecting network devices is located in Chapter 3, “Connecting Network Devices and
Checking Connectivity”.
The FastIron WS systems ship with all of the following items. Please review the list below and verify the contents of your shipping
container. If any items are missing, please contact the place of purchase.
Package contents
The package contents of device are listed below:
•
Brocade FastIron WS
•
115V AC power cable (for AC sourced devices)
•
Rack mount brackets
•
Warranty card
•
A straight-through EIA/TIA DB-9 serial cable (F or F). The serial cable can be ordered separately from Brocade
Communications Systems, Inc.. If you prefer to build your own cable, refer to the pinout information in “Attaching a PC or
terminal” on page 36.
General requirements
To manage the system, you need the following items for serial connection to the device:
•
A management station, such as a PC running a terminal emulation application.
You use the serial connection to perform basic configuration tasks, including assigning an IP address and network mask to the system.
This information is required to manage the system using the Web Management Interface or IronView Network Manager or using the CLI
through Telnet.
Summary of installation tasks
Follow the steps listed below to install your FastIron WS. Details for each of these steps are provided in this chapter and in the following
chapter.
20 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installation precautions
Installation precautions
Follow these precautions when installing a Brocade device.
General precautions
All fiber-optic interfaces use Class 1 lasers.
TABLE 1 Summary of installation tasks
Task
number
Task Where to find more information
1 Ensure that the physical environment that will host the
device has the proper cabling and ventilation.
“Preparing the installation site” on page 22
2 Install any required optional modules into the device. “Activating power to the device” on page 35
3 Install the Brocade device on a desktop, in an
equipment rack.
“Installing the device” on page 23
4 Once the device is physically installed, plug the device
into a nearby power source that adheres to the
regulatory requirements outlined in this manual.
“Activating power to the device” on page 35
5 Verify that the system LEDs are registering the proper
LED state after power-on of the system.
“Verifying proper operation” on page 36
6 Attach a terminal or PC to the Brocade device. This will
enable you to configure the device through the
Command Line Interface (CLI).
“Attaching a PC or terminal” on page 36
7 No default password is assigned to the CLI. For
additional access security, assign a password.
“Assigning permanent passwords” on page 29
8 Before attaching equipment to the device, you need to
configure an interface IP address to the subnet on which
it will be located. Initial IP address configuration is
performed using the CLI with a direct serial connection.
Subsequent IP address configuration can be performed
using the Web management interface.
“Configuring IP addresses” on page 30
9 Once you power on the device and assign IP addresses,
the system is ready to accept network equipment.
“Devices running layer 3 software” on page 32
10 Test IP connectivity to other devices by pinging them
and tracing routes.
“Testing connectivity” on page 37
11 Continue configuring the device using the CLI or the
Web management interface. You also can use IronView
Network Manager to manage the device. Refer to the
<Italic>Brocade IronView Network Management User’s
Guide for information.
<Italic>FastIron Configuration Guide
12 Secure access to the device. <Italic>FastIron Configuration Guide
Brocade FastIron WS Hardware Installation Guide 21
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installation precautions
Do not install the device in an environment where the operating ambient temperature might exceed 40
o
C
(104
o
F).
Make sure the air flow around the front and sides of the device is not restricted.
Never leave tools inside the device.
Lifting precautions
Make sure the rack or cabinet housing the device is adequately secured to prevent it from becoming
unstable or falling over.
Mount the devices you install in a rack or cabinet as low as possible. Place the heaviest device at the
bottom and progressively place lighter devices above.
Power precautions
Use a separate branch circuit for each AC power cord, which provides redundancy in case one of the
circuits fails.
To avoid high voltage shock, do not open the device while the power is on.
22 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Preparing the installation site
Ensure that the device does not overload the power circuits, wiring, and over-current protection. To
determine the possibility of overloading the supply circuits, add the ampere (amp) ratings of all devices
installed on the same circuit as the device. Compare this total with the rating limit for the circuit. The
maximum ampere ratings are usually printed on the devices near the input power connectors.
Disconnect the power cord from all power sources to completely remove power from the device.
If the installation requires a different power cord than the one supplied with the device, make sure you
use a power cord displaying the mark of the safety agency that defines the regulations for power cords in
your country. The mark is your assurance that the power cord can be used safely with the device.
Preparing the installation site
Cabling infrastructure
Ensure that the proper cabling is installed at the site. Refer to Chapter 5, “Hardware Specifications” or www.brocade.com for a summary
of supported cabling types and their specifications.
Installation location
Before installing the device, plan its location and orientation relative to other devices and equipment. Devices can be mounted in a
standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location.
The site should:
•
Maintain temperatures within 0 to 40 °C (32 to 104 °F) and humidity levels within 5% to 95%, non-condensing.
•
Allow a minimum of 3in. of space between the sides and the back of the device and walls or other obstructions for proper air
flow.
•
Allow at least 3in. of space at the front and back of the device for the twisted-pair, fiber-optic, and power cabling.
•
Be accessible for installing, cabling and maintaining the devices.
•
Allow the status LEDs to be clearly visible.
•
Allow for twisted-pair cable to be always routed away from power lines, fluorescent lighting fixtures and other sources of
electrical interference, such as radios and transmitters.
•
Allow for the device to be connected to a separate grounded power outlet that provides 110 to 240 VAC, 50 to 60 Hz, is within
2 m (6.6 feet) of each device and is powered from an independent circuit breaker. As with any equipment, a filter or surge
suppressor is recommended.
Brocade FastIron WS Hardware Installation Guide 23
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Preparing the installation site
Installing the device
You can install Brocade systems on a desktop or in an equipment rack.
Make sure the rack or cabinet housing the device is adequately secured to prevent it from becoming
unstable or falling over.
Mount the devices you install in a rack or cabinet as low as possible. Place the heaviest device at the
bottom and progressively place lighter devices above.
Desktop installation
FIGURE 1 Attaching the adhesive feet
1. Attach the four adhesive feet to the bottom of the first device.
2. Set the device on a flat desktop, table, or shelf near an AC power source. Make sure that adequate ventilation is provided for the
system. A 3-inch clearance is recommended on each side.
3. If you are installing a single device only, go to “Activating power to the device” on page 35.
4. If you are installing multiple devices, attach the adhesive feet to each one. Place each device squarely on top of the one below, in
any order.
5. If you are also installing an redundant power supply, place it close to the device.
Rack mount installation
NOTE
You need a #2 Phillips screwdriver for installation.
24 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Preparing the installation site
Before mounting the device in a rack, consider the following factors:
•
Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the
rack-environment temperature is within the specified operating temperature range. (Refer to “Operating environment” on
page 48.)
•
Mechanical loading: Do not place any equipment on top of a rack-mounted device.
•
Circuit overloading: Be sure that the supply circuit to the rack assembly is not overloaded.
•
Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections
other than direct connections to the mains.
To mount devices in rack follow the steps given below.
1. Remove the rack mount kit from the shipping carton. The kit contains two L-shaped mounting brackets and mounting screws.
2. Attach the mounting brackets to the sides of the device as illustrated in Figure 2.
FIGURE 2 Attaching the brackets
3. Attach the device in the rack as illustrated in Figure 3.
FIGURE 3 Installing the device in a rack
4. If you are installing a single device, proceed to “Activating power to the device” on page 35.
Brocade FastIron WS Hardware Installation Guide 25
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
5. If you are installing multiple devices, mount them in the rack, one below the other, in any order.
6. If you are also installing an redundant power supply, mount it in the rack below the other devices.
Installing a redundant power supply
RPS2-EIF Redundant Power Supply
The Brocade External Redundant Power Supply (RPS2-EIF) can supply a maximum of 150 Watts of output power per port, a total of
600 Watts of backup power to four FastIron WS devices in the event of an AC loss or failure of an internal power supply.
The system operates as a backup to the internal power supply for a device. If an internal power supply fails, the redundant power supply
will support the device without affecting network operation.
The following devices are supported by the FastIron RPS2-EIF:
•
FastIron WS FWS624
•
FastIron WS FWS648
Features and benefits
The RPS2-EIF power supply provides the following features and benefits:
•
Supports four FastIron WS devices with 12V DC output
•
Status LEDs located on the front panel
•
AC line cord can draw power from a different supply circuit
•
DC line cord provides backup power to the attached device
•
Thermal overload protection prevents the redundant power supply from overheating if a thermal overload occurs.
•
Over-voltage protection shuts down an output channel if voltage exceeds a preset threshold.
•
Over-current protection shuts down the power supply if output load exceeds a preset threshold.
•
Short-circuit protection prevents damage to the power supply due to a short circuit on any output channel.
•
Operates under a no-load condition.
Front and rear panels
Four power indicators and one fan indicator are located on the front panel of the power supply. The AC supply and DC backup
receptacles are located on the rear panel of the power supply.
26 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
FIGURE 4 Front and rear panels
Package contents
The RPS2-EIF power supply shipping package contains:
•
Redundant power supply (RPS2-EIF)
•
One AC supply power cord — US, Continental Europe or UK
•
Four DC backup power cords with IEC connectors on both ends (length 152 cm each)
•
Rack Mounting Kit containing brackets and screws
•
Adhesive feet
•
User agreement envelope
•
Registration card
LEDs
The RPS2-EIF LEDs are described in Figure 5, Table 2 and Table 3.
FIGURE 5 RPS2-EIF LEDs
1 Redundant power sockets 4-3 4 Power socket
2 Fans 5 Port and system status indicators
3 Redundant power sockets 2-1
1 Port indicators 2 System indicators
Link
Activity
1234Fan Thermal Power
100-240V, 50-60Hz 10A
RPS 1
RPS 2RPS 3RPS 4
4
3
2
1
5
21
Brocade FastIron WS Hardware Installation Guide 27
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
RPS12 external redundant power supply
The external redundant power supply (RPS12) can supply backup power to one of four connected devices in the event of an AC loss or
failure of an internal power supply. The system supplies the failed device with up to 120 W for primary 12 VDC power, and up to 780 W
of -54 VDC PoE power (for PoE devices connected to the failed device).
The RPS12 monitors the power status for all attached devices and provides power to first device with a detected power failure. The
RPS12 supports the full load of the device without affecting network operation. When the RPS12 is supplying power to a device, it cannot
provide power to other connected devices.
When a device fails, the RPS12 sends status information to the other connected devices, which then communicate the status of the
RPS12 to network management software.
The following devices are supported by the FastIron RPS12:
•
FastIron WS FWS624-POE
•
FastIron WS FWS648-POE
•
FastIron WS FWS624G-POE
•
FastIron WS FWS648G-POE
Features and benefits
•
Supports up to four connections to FastIron WS PoE devices
TABLE 2 Port status LEDs - RPS2-EIF
LED (1~4) Condition Status
Link Off The port does not have a valid connection to a device.
On Yellow The port has a valid connection to a device.
Flashing Yellow There has been an internal power failure.
Activity Off The port is not providing power to the connected device.
Flashing Green The port has been shut down due to one of the following conditions:
• The device has detected an over-current condition.
• One or more of the fans have failed.
On Green The port is providing power to a connected device.
TABLE 3 System status LEDs - RPS2-EIF
LED Condition Status
Power On Green AC power is being supplied to the power supply.
Off No AC power is being supplied to the power supply.
Fan On Green The fans are functioning normally.
Flashing Yellow One or more of the fans is not operating properly.
Off The fans are not receiveing power.
Thermal On Green The temperature of the unit is within an acceptable range.
Flashing Yellow The temperature is close to exceeding acceptable levels.
Off The thermal detector has failed, or the unit is powered off.
28 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
•
Can supply one out of four connected device with 12V DC primary power and -54V DC PoE power
•
Status LEDs located on the front panel
•
AC line cord draws power from a different supply circuit
•
DC line cord provides backup power to the attached device
•
Thermal overload protection prevents the RPS12 from overheating if a thermal overload occurs.
•
Over-voltage protection shuts down an output channel if the voltage exceeds a preset threshold.
•
Over-current protection shuts down the RPS12 if output load exceeds a preset threshold.
•
Short-circuit protection prevents damage to the RPS12 due to a short circuit on any output channel.
•
The power supply will operate under a no-load condition.
•
Supports hot connection of FastIron WS PoE devices
Front and rear panels
Four power indicators and one fan indicator are located on the front panel. The AC supply and DC backup receptacles are located on the
rear panel.
FIGURE 6 Front and Rear Panels
Package contents
•
Redundant power supply (RPS12)
•
One AC supply power cord — US, Continental Europe or UK
•
One DC power cord with IEC connectors on both ends (length 152 cm each)
•
Rack Mounting Kit containing brackets and screws
•
Adhesive feet
•
User agreement envelope
•
Registration card
1 Power socket 2 Redundant power sockets 4-3
3 Redundant power sockets 2-1 4 Power system status indicator
Status
Power
Fan
Activity
Link
1234
123
4
Brocade FastIron WS Hardware Installation Guide 29
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
LEDs
Figure 7, Table 3, and Table 4 describe the functions of the RPS12 LEDs.
FIGURE 7 FastIron RPS12 LEDs
1 Port indicators 2 System indicators
TABLE 4 Port Status LEDs - RPS12
LED (1~4) Condition Status
Link Off The port does not have a valid connection to a device.
On Yellow The port has a valid connection to a device
Activity Off The port may be connected to a device, but is not delivering power to
the device.
On Green The port is providing power to a connected device.
TABLE 5 System Status LEDs - RPS12
LED Condition Status
Power On Green AC power is being supplied to the power supply.
Off No AC power is being supplied to the power supply.
Status On Green The power supply is operating normally.
On Red The power supply has detected an abnormal condition.
Fan On Green The cooling fan is operating normally.
On Red The cooling fan is not operating normally.
Status
Power
Fan
Activity
Link
1234
21
30 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
Selecting a redundant power supply installation site
RPS2-EIF and RPS12 power supplies can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow these
guidelines when choosing a location.
Do not place a redundant power supply on the floor as the case is not waterproof. It is recommended that
either of the redundant power supplies be installed in a network equipment rack.
Remove the power cord from a power supply before you install it in or remove it from the device.
Otherwise, the power supply or the device could be damaged as a result. (The device can be running while
a power supply is being installed or removed, but the power supply itself should not be connected to a
power source.)
The installation site should meet these requirements:
•
Be at the center of all the devices you want to link, and near a power outlet.
•
Maintain temperatures within 0 to 40 °C (32 to 104 °F) and humidity levels within 5% to 95%, non-condensing.
•
Provide adequate space (approximately 5.08 cm (2 inches) on all sides for proper air flow.
•
Be accessible for installing, cabling and maintaining the devices.
•
Allow the status LEDs to be clearly visible.
•
Allow for twisted-pair cable to be always routed away from power lines, fluorescent lighting fixtures and other sources of
electrical interference, such as radios and transmitters.
•
Provide a separate grounded power outlet that provides 100 to 240 VAC, 50-60 Hz, is within 2.44 m (8 feet) of each device,
and is powered from an independent circuit breaker.
•
As with any electrical equipment, a filter or surge suppressor is recommended.
Equipment checklist
When you unpack the RPS2-EIF or RPS12 power supply, make sure you have received all the components. (Refer to “Package contents”
on page 26.) Before beginning the installation, be sure you have all other necessary installation equipment.
Optional rack-mounting equipment
If you plan to rack-mount a redundant power supply, have the following equipment available:
•
Four mounting screws for each device you plan to install (screws are not included)
•
A screwdriver (Phillips or flathead, depending on the type of screws used)
Mounting a redundant power supply in a rack
Before mounting the redundant power supply in a rack, consider the following factors:
•
Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the
rack-environment temperature is within the specified operating temperature range.
Brocade FastIron WS Hardware Installation Guide 31
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
•
Mechanical loading: Do not place any equipment on top of a rack-mounted device.
•
Circuit overloading: Be sure that the supply circuit to the rack assembly is not overloaded.
•
Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections
other than direct connections to the mains.
Follow these steps to install a redundant power supply in a rack.
1. Attach the brackets to the power supply using the screws provided in the Bracket Mounting Kit. Refer to Figure 8.
FIGURE 8 Attaching the mounting brackets
2. Mount the power supply in the rack, using four rack-mounting screws (not provided). Refer to Figure 9.
FIGURE 9 Installing the redundant power supply in a rack
3. If installing multiple redundant power supplies, mount them in the rack one below the other, in any order.
Link
Activity
1234Fan Thermal Power
32 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
Desktop or shelf mounting
1. Attach the four adhesive feet to the bottom of the first redundant power supply. Refer to Figure 10.
FIGURE 10 Attaching the adhesive feet
2. Set the power supply on a flat surface near an AC power source, making sure there are at least 5.08 cm (2 inches) of space on
all sides for proper air flow.
Connecting devices to the redundant power supply
The FastIron RPS2-EIF is supported on the following devices:
•
FastIron WS624
•
FastIron WS648
The FastIron RPS12 is supported on the following devices:
•
FastIron FWS624-POE
•
FastIron FWS648-POE
To connect devices to a redundant power supply, follow these steps.
Brocade FastIron WS Hardware Installation Guide 33
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
1. Connect one end of the AC cord to the AC receptacle on the device, and the other end to a grounded power outlet. Refer to
Figure 11.
FIGURE 11 Power receptacle
2. Connect one end of a DC cord to the redundant power receptacle on the device and the other end to an available receptacle on
the redundant power supply.
3. Repeat step 1 and step 2 to connect up to four devices to the redundant power supply. Refer to Figure 12.
4. Connect one end of the AC cord to the AC receptacle on the redundant power supply, and the other end to a grounded power
outlet.
5. Check the LEDs on the redundant power supply to ensure proper operation. On the RPS2-EIF and RPS12, the Power LED
should light up. If the LEDs do not light, refer to “Troubleshooting” on page 53 for more information.
FIGURE 12 Connecting multiple devices to a redundant power supply.
100-240V, 50-60Hz 10A
RPS 1
1
5
3
6
4
2
34 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Installing a redundant power supply
NOTE
For International use, you may need to change the AC line cord. You must use a line cord set that has been approved for the
receptacle type in your country.
Port pin-out diagram for the RPS2-EIF power supply
Figure 13 and Table 6 describe the pin-outs for the RPS2-EIF power supply.
FIGURE 13 RPS2-EIF power supply port pinout diagram
1 Input port 4 FWS devices
2 AC power supply no.1 5 Output port
3 Redundant power supply 6 AC power supply no.2
TABLE 6 Port pin-out diagram for the RPS2-EIF power supply
Pin Name Description
1, 7, 8, 14 GND Ground connection
2, 9 N.C. No current
3, 4, 5, 6 12 V 12 volts current
10 RPS Present Indicates that a redundant power supply is attached and
functioning
11, 12 Status 1, Status 2 Status indicator
13 Power Good Indicates that power is being supplied to the redundant power
supply
GND
18
29
310
411
512
613
714
N.C.
N.C.
GND
12 V RPS Present
12 V Status 1
12 V Status 2
12 V Power Good
GND GND
Brocade FastIron WS Hardware Installation Guide 35
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Activating power to the device
Port pin-out diagram for the RPS12 power supply
Figure 14 and Table 7 describe the pin-out diagram for the RPS12 power supply.
FIGURE 14 Pin-out diagram for the RPS12 power supply.
Activating power to the device
After you complete the physical installation, you can activate power to the device.
TABLE 7 Port pin-out diagram for the RPS12 power supply
Pin Name Description
1, 2, 3 -54 V -54 volts connection
4, 5, 6, 13 N.C. No connection
7, 8 12 V 12 volts connection
9, 18 12 V RTN 12 volts return connection
10, 11, 12 -54 V RTN -54 volts return connection
14 RPS Present Indicates that a redundant power supply is attached and
functioning
15 RPS Type Indicates either load-sharing or redundant mode
16 RPS Power Good Indicates that power is being supplied to the redundant power
supply
17 Power Good Connected device internal power supply status
2
110
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
-54 V -54 V RTN
N. C.
RPS Present
Power Good
-54 V
-54 V
N. C.
N. C.
N. C.
12 V
12 V RTN
12 V
-54 V RTN
-54 V RTN
12 V RTN
RPS Type
RPS Power Good
36 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Verifying proper operation
1. Remove the power cord from the shipping package.
2. Attach the AC power cable to the AC connector on the rear panel.
3. Insert the power cable plug into a 115V/120V outlet.
NOTE
To turn the system off, simply unplug the power cord or cords.
NOTE
The socket should be installed near the equipment and should be easily accessible.
NOTE
If the outlet is not rated 115/120V, stop and get the appropriate cable for the outlet.
Verifying proper operation
After you have installed a redundant power supply, verify that the device is working properly by plugging it into a power source and
verifying that it passes the self test.
1. Connect the power cord supplied with the device to the power connector on the power supply on the rear of the device.
2. Insert the other end into a properly grounded electrical outlet.
NOTE
FastIron devices do not have power switches. They power on when you connect a power cord to the device and to a power
source.
If your installation requires a different power cord than that supplied with the device, make sure you use a power cord that
displays the mark of the safety agency that defines the regulations for power cords in your country. The mark is your
assurance that the power cord can be used safely with the device.
3. Verify that the LED for the power supply is green.
4. Verify proper operation by observing the LEDs.
LEDs for linked ports will come on during the boot process, then all LEDs will go off. Once the boot sequence is complete, LEDs
for linked ports will again come on.
For more details on specific LED conditions after system start-up, refer to the section, “LEDs” on page 26.
Attaching a PC or terminal
To assign an IP address, you must have access to the text-based command line interface (CLI). The CLI is described in detail in the
<Italic>FastIron Configuration Guide. You can access the CLI by attaching a serial cable to the Console port. After you assign an IP
address, you can access the system through Telnet, the Web Management Interface, or IronView Network Manager.
Attach a management station using the serial port.
1. Connect a PC or terminal to the serial port using a straight-through cable. The serial port has a male DB-9 connector.
NOTE
You will need to run a terminal emulation program on the PC.
Brocade FastIron WS Hardware Installation Guide 37
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Attaching a PC or terminal
2. Open the terminal emulation program and set the session parameters as follows:
•
Baud: 9600 bps
•
Data bits: 8
•
Parity: None
•
Stop bits: 1
•
Flow control: None
The serial communication port acts as a management connection point for a PC or SNMP workstation. Brocade devices have a standard
male DB-9 connector, shown in Figure 15.
FIGURE 15 Serial port (DB-9 DTE) pin-out
Most PC serial ports also require a cable with a female DB-9 connector. Terminal connections will vary, requiring either a DB-9 or DB-25
connector, male or female. Serial cable options between a Brocade device and a PC or terminal are shown in Table 8.
NOTE
As indicated in Table 8, some of the wires should not be connected.
TABLE 8 Serial cable wiring map
9-pin serial port on device Null modem 9-pin DTE port on PC
2 TXD (transmit data) -------------------------
--->
2 RXD (receive data)
3 RXD (receive data) <------------------------
----
3 TXD (transmit data)
5 SGND (signal ground) <------------------------
-->
5 SGND (signal ground)
No other pins are used.
6 9
15
38 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Installing FWS624 and FWS648 Models
Attaching a PC or terminal
Brocade FastIron WS Hardware Installation Guide 39
Part Number: 53-1002498-03
Connecting Network Devices and
Checking Connectivity
Assigning permanent passwords
The procedures in this manual are for qualified service personnel.
By default, the CLI is not protected by passwords. To secure CLI access, Brocade strongly recommends assigning passwords. Refer to
the <Italic>FastIron Configuration Guide.
NOTE
You cannot assign a password using the Web Management Interface. You can assign passwords using IronView Network
Manager if an enable password for a Super User has been configured on the device.
The CLI contains the following access levels:
•
User EXEC – The level you enter when you first start a CLI session. At this level, you can view some system information but you
cannot configure system or port parameters.
•
Privileged EXEC – This level is also called the Enable level and can be secured by a password. You can perform tasks such as
manage files on the flash module, save the system configuration to flash, and clear caches at this level.
•
CONFIG – The configuration level. This level lets you configure the system IP address and configure switching and routing
features. To access the CONFIG mode, you must already be logged into the Privileged level of the EXEC mode.
You can set the following levels of Enable passwords:
•
Super User – Allows complete read-and-write access to the system. This is generally for system administrators and is the only
password level that allows you to configure passwords.
NOTE
You must set a super user password before you can set other types of passwords.
•
Port Configuration – Allows read-and-write access for specific ports but not for global (system-wide) parameters.
•
Read Only – Allows access to the Privileged EXEC mode and CONFIG mode but only with read access.
Set passwords.
1. At the opening CLI prompt, enter the following command to change to the Privileged level of the EXEC mode.
Brocade>enable
2. Access the CONFIG level of the CLI by entering the following command.
Brocade
# configure terminal
Brocade(config)
#
3. Enter the following command to set the super-user password.
Brocade(config)# enable super-user-password <text>
40 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Configuring IP addresses
NOTE
You must set the super-user password before you can set other types of passwords.
4. Enter the following commands to set the port configuration and read-only passwords.
Brocade(config)# enable port-config-password <text>
Brocade(config)# enable read-only-password <text>
NOTE
If you forget your super-user password, refer to “Recovering from a lost password” on page 40.
Syntax: enable super-user-password | read-only-password | port-config-password <text>
Passwords can be up to 32 characters long.
Recovering from a lost password
By default, the CLI does not require passwords. However, if someone has configured a password for the device but the password has
been lost, you can regain super-user access to the device using the following procedure.
NOTE
Recovery from a lost password requires direct access to the serial port and a system reset.
Recover from a lost password.
1. Start a CLI session over the serial interface to the Brocade device.
2. Reboot the device.
3. While the system is booting, before the initial system prompt appears, enter b to enter the boot monitor mode.
4. Enter no password at the prompt. (You cannot abbreviate this command.)
5. Enter boot system flash primary at the prompt. This command causes the device to bypass the system password check.
After the console prompt reappears, assign a new password.
Configuring IP addresses
You must configure at least one IP address using the serial connection to the CLI before you can manage the system using the other
management interfaces.
Brocade devices support both classical IP network masks (Class A, B, and C subnet masks, and so on) and Classless Interdomain Routing
(CIDR) network prefix masks:
•
To enter a classical network mask, enter the mask in IP address format. For example, enter
“209.157.22.99 255.255.255.0” for an IP address with a Class-C subnet mask.
•
To enter a prefix number for a network mask, enter a forward slash ( / ) and the number of bits in the mask immediately after the
IP address. For example, enter “209.157.22.99/24” for an IP address that has a network mask with 24 significant (“mask”) bits.
By default, the CLI displays network masks in classical IP address format (example: 255.255.255.0). You can change the display to the
prefix format. Refer to the <Italic>FastIron Configuration Guide.
Brocade FastIron WS Hardware Installation Guide 41
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Configuring IP addresses
Devices running layer 2 software
Configure an IP Address on a device running Layer 2 software.
1. At the opening CLI prompt, enter enable.
Brocade
> enable
2. Enter the following command at the Privileged EXEC level prompt (for example, Brocade#), then press Enter. This command
erases the factory test configuration if still present:
Brocade
# erase startup-config
Use the erase startup-config command only for new systems. If you enter this command on a system you
have already configured, the command erases the configuration. If you accidentally do erase the
configuration on a configured system, enter the write memory command to save the running configuration
to the startup-config file.
3. Access the configuration level of the CLI by entering the following command.
Brocade
# configure terminal
(Privileged EXEC Level)
Brocade
(config)#
(Global CONFIG Level)
4. Configure the IP address and mask for the switch.
Brocade(config)# ip address 192.22.3.44 255.255.255.0
5. Set a default gateway address for the switch.
Brocade(config)# ip default-gateway 192.22.3.1
NOTE
You do not need to assign a default gateway address for single subnet networks.
Syntax: enable [<password>]
Syntax: configure terminal
Syntax: [no] ip address <ip-addr> <ip-mask>
or
Syntax: [no] ip address <ip-addr>/<mask-bits>
Syntax: ip default-gateway <ip-addr>
Devices running layer 3 software
NOTE
Devices require a software license to be able to run Edge Layer 3 features. For details, see the <Italic>FastIron Configuration
Guide.
Configuring IP addresses
You can configure an IP address on the following types of Layer 3 switch interfaces:
•
Ethernet port
42 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Configuring IP addresses
•
Virtual routing interface (also called a Virtual Ethernet or “VE”)
•
Loopback interface
By default, you can have up to 24 IP addresses on each interface, but you can increase this number to 128 IP addresses.
NOTE
Once you configure a virtual routing interface on a VLAN, you cannot configure Base Layer 3 interface parameters on individual
ports in the VLAN. Instead, you must configure the parameters on the virtual routing interface itself.
Brocade devices support both classical IP network masks (Class A, B, and C subnet masks, and so on) and Classless Interdomain Routing
(CIDR) network prefix masks:
•
To enter a classical network mask, enter the mask in IP address format. For example, enter
“209.157.22.99 255.255.255.0” for an IP address with a Class-C subnet mask.
•
To enter a prefix network mask, enter a forward slash ( / ) and the number of bits in the mask immediately after the IP address.
For example, enter “209.157.22.99/24” for an IP address that has a network mask with 24 significant bits (ones).
By default, the CLI displays network masks in classical IP address format (example: 255.255.255.0). You can change the display to
prefix format.
Assigning an IP address to an Ethernet port
To assign an IP address to port 0/1/1, enter the following commands.
Brocade(config)# interface ethernet 0/1/1
Brocade(config-if-0/1/1)# ip address 192.45.6.1 255.255.255.0
NOTE
You also can enter the IP address and mask in CIDR format, as follows.
Brocade(config-if-0/1/1)#ip address 192.45.6.1/24
Syntax: [no] ip address <ip-addr> <ip-mask>
or
Syntax: [no] ip address <ip-addr>/<mask-bits>
Assigning an IP address to a loopback interface
Loopback interfaces are always up, regardless of the states of physical interfaces. You can configure up to eight loopback interfaces.
You can add up to 24 IP addresses to each loopback interface.
To add a loopback interface, enter commands such as those shown in the following example.
Brocade(config)# exit
Brocade(config)# int loopback 1
Brocade(config-lbif-1)# ip address 10.0.0.1/24
Syntax: interface loopback <num>
The <num> parameter specifies the virtual interface number. You can specify from 1 to the maximum number of virtual interfaces
supported on the device. To display the maximum number of virtual interfaces supported on the device, enter the show default values
command. The maximum is listed in the System Parameters section, in the Current column of the virtual-interface row.
Brocade FastIron WS Hardware Installation Guide 43
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Configuring IP addresses
Assigning an IP address to a virtual routing interface
A virtual interface is a logical port associated with a Layer 3 Virtual LAN (VLAN) configured on a Base Layer 3 Switch. You can configure
routing parameters on the virtual interface to enable the Layer 3 Switch to route protocol traffic from one Layer 3 VLAN to the other,
without using an external router.
This section describes how to configure an IP address on a virtual interface.
NOTE
The switch uses the lowest MAC address on the device (the MAC address of port 1 or 0/1/1) as the MAC address for all ports
within all virtual interfaces you configure on the device.
To add a virtual interface to a VLAN and configure an IP address on the interface, enter commands such as the following.
Brocade(config)# vlan 2 name IP-Subnet_1.1.2.0/24
Brocade(config-vlan-2)# untag 0/1/1 to 0/1/4
Brocade(config-vlan-2)# router-interface ve1
Brocade(config-vlan-2)# interface ve1
Brocade(config-vif-1)# ip address 1.1.2.1/24
The first two commands in this example create a Layer 3 protocol-based VLAN name “IP-Subnet_1.1.2.0/24” and add a range of
untagged ports to the VLAN. The router-interface command creates virtual interface 1 as the routing interface for the VLAN. The last two
commands change to the interface configuration level for the virtual interface and assign an IP address to the interface.
Syntax: router-interface ve <num>
Syntax: interface ve <num>
Deleting an IP address
To delete an IP address, enter a command such as the following.
Brocade(config-if-0/1/1)# no ip address 1.1.2.1
This command deletes IP address 1.1.2.1. You do not need to enter the subnet mask.
To delete all IP addresses from an interface, enter the following command.
Brocade(config-if-0/1/1)# no ip address *
Syntax: no ip address <ip-addr> | *
Connecting network devices
Brocade devices support connections to other vendors’ routers, switches, and hubs, as well other Brocade devices.
Connectors
Refer to “Cable length summary table” on page 51.
For port pinouts, refer to the section “Pinouts and signalling” on page 49.
Cable specifications
Refer to “Cable specifications” on page 50 for cable lengths and types.
44 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Configuring IP addresses
Connecting to Ethernet or Fast Ethernet Hubs
For copper connections to Ethernet hubs, a 10/100BaseTX or 1000BaseT switch, or another Brocade device, a crossover cable is
required (Figure 1 and Figure 2). If the hub is equipped with an uplink port, it will require a straight-through cable instead of a crossover
cable.
NOTE
The 802.3ab standard (automatic MDI or MDIX detection) calls for automatic negotiation of the connection between two
1000Base-T ports. Therefore, a crossover cable may not be required; a straight-through cable may work as well. For more
information about this feature, refer to the <Italic>FastIron Configuration Guide.
FIGURE 1 UTP crossover cable
FIGURE 2 Straight-through cable
Connecting to workstations, servers, or routers
Straight-through UTP cabling is required for direct UTP attachment to workstations, servers, or routers using network interface cards
(NICs).
Orange
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Green
Brown
Blue
White/Orange Stripe
White/Green Stripe
White/Blue Stripe
White/Brown Stripe
End BEnd A
EIA/TIA 568B RJ-45 Wiring Standard
10/100BASE-TX Crossover Cable
Orange
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Green
Brown
Blue
White/Orange Stripe
White/Green Stripe
White/Blue Stripe
White/Brown Stripe
End BEnd A
EIA/TIA 568B RJ-45 Wiring Standard
10/100BASE-TX Straight-through Cable
Brocade FastIron WS Hardware Installation Guide 45
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Configuring IP addresses
Fiber cabling is required for direct attachment to Gigabit NICs or switches and routers through fiber ports. Refer to “Connecting a network
device to a fiber port” on page 45.
Automatic MDI or MDIX detection
All 10/100 and Gigabit Ethernet Copper ports on the Brocade FastIron WS devices support automatic Media Dependent Interface (MDI)
and Media Dependent Interface Crossover (MDIX) detection. This feature is enabled on all 10/100 and Gigabit copper ports by default.
For each port, you can disable auto MDI or MDIX, designate the port as an MDI port, or designate the port as an MDIX port.
For more information about this feature and how configure it, refer to the <Italic>FastIron Configuration Guide.
Connecting a network device to a fiber port
For direct attachment from the Brocade device to a Gigabit NIC, switch, or router, fiber cabling with an LC connector is required.
To connect the Brocade device to another network device using a fiber port, you must do the following:
•
Install a fiber optic module (SFP transceiver or mini-GBIC)
•
Cable the fiber optic module
The following sections provide information about performing these tasks.
Installing a fiber optic module
You must install a fiber optic module (SFP) in each SFP slot you want to use.
You can install a new fiber optic module in an SFP slot while the FastIron WS CHE1 is powered on and running.
Before installing one of these modules into the slot, have the following on hand.
NOTE
An ESD wrist strap with a plug for connection to a metal surface. For safety reasons, the ESD wrist strap should contain a series
1 megohm resistor.
All fiber optic interfaces use Class 1 lasers.
Install a fiber optic module.
1. Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack) to act as
ground.
2. Remove the new module from its protective packaging.
3. Gently insert the fiber optic module into the slot until the module clicks into place. The module is keyed to prevent incorrect
insertion.
46 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Testing connectivity
FIGURE 3 Installing a fiber optic module
Cabling a fiber optic module
Cable a fiber optic module.
1. Remove the protective covering from the fiber-optic port connectors and store the covering for future use.
2. Before cabling a fiber optic module, Brocade strongly recommends cleaning the cable connectors and the port connectors. For
more information, refer to “Cleaning the fiber-optic connectors” on page 46.
3. Gently insert the cable connectors (a tab on each connector should face upward) into the port connectors until the tabs lock into
place.
4. Observe the link and active LEDs to determine if the network connections are functioning properly. For more information about
the LED indicators, refer to Table 1 on page 47.
Cleaning the fiber-optic connectors
To avoid problems with the connection between the fiber optic module (SFP (mini-GBIC)) and the fiber cable connectors, Brocade
strongly recommends cleaning both connectors each time you disconnect and reconnect them. In particular, dust can accumulate in the
connectors and cause problems such as reducing the optic launch power.
To clean the fiber cable connectors, Brocade recommends using the fiber-optic reel-type cleaner that shipped with your FastIron WS
CHE1. You can also purchase this type of cleaner from the following Web site:
http://www.fisfiber.com/Home_Page.asp
When not using an SFP connector, make sure to keep the protective covering on.
Testing connectivity
You can observe the LEDs related to network connection.
Pinging an IP address
To verify that a FastIron WS device can reach another device through the network, enter a command such as the following at any level of
the CLI on the Brocade device:
Brocade>ping 192.33.4.7
Brocade FastIron WS Hardware Installation Guide 47
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Testing connectivity
Syntax: ping <ip addr> | <hostname> [source <ip addr>] [count <num>] [timeout <msec>] [ttl <num>] [size <byte>] [quiet]
[numeric] [no-fragment] [verify] [data <1-to-4 byte hex>] [brief]
NOTE
If you send the ping to the IP broadcast address, the device lists the first four responses to the ping.
Observing LEDs
After you install the network cables, you can observe certain LEDs to determine if the network connections are functioning properly.
Table 1 outlines the LEDs related to the network connections, the desired state of each LED, possible abnormal states of each LED, and
what to do if an LED indicates an abnormal state.
If a problem persists after taking these actions, contact Brocade Technical Support.
Tracing a route
To determine the path through which a Brocade device can reach another device, enter a command such as the following at any level of
the CLI on the Brocade device.
Brocade>traceroute 192.33.4.7
TABLE 1 Network connection-related LED states
LED Desired state Meaning Abnormal
state
Meaning or action
Link (1-24/48)
SFP (1-4)
On (Green) A link is established with
the remote port.
Off A link is not established with the remote port. You can do
the following:
•
Verify that the connection to the other network
device has been properly made. Also, make certain
that the other network device is powered on and
operating correctly.
•
Verify that the transmit port on the Brocade device is
connected to the receive port on the other network
device, and that the receive port on the Brocade
device is connected to the transmit port on the other
network device. If you are not certain, remove the
two cable connectors from the port connector and
reinsert them in the port connector, reversing their
order.
•
Dust may have accumulated in the cable connector
or port connector. For information about cleaning the
connectors, refer to “Cleaning the fiber-optic
connectors” on page 46.
•
If the other actions do not resolve the problem, try
using a different port or a different cable.
Active
(1-24/48)
SFP (1-4)
On or blinking
(Yellow)
The port is transmitting
and receiving user
packets.
Off for an
extended
period.
The port is not transmitting or receiving user packets. You
can do the following:
•
Check the Link LED to make sure the link is still
established with the remote port. If not, take the
actions described in the Meaning or Action column
for the Link LED.
•
Verify that the port has not been disabled through a
configuration change. You can use the CLI. If you
have configured an IP address on the device, you
also can use the Web management interface or
IronView Network Manager.
48 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Troubleshooting network connections
Syntax: traceroute <host-ip-addr> [maxttl <value>] [minttl <value>] [numeric] [timeout <value>]
[source-ip <ip addr>]
The CLI displays trace route information for each hop as soon as the information is received. Traceroute requests display all responses to
a given TTL. In addition, if there are multiple equal-cost routes to the destination, the Brocade device displays up to two responses by
default.
Troubleshooting network connections
Follow these guidelines when troubleshooting your network connections:
•
For the indicated port, verify that both ends of the cabling (at the Brocade device and the connected device) are snug.
•
Verify that the Brocade device and the connected device are both powered on and operating correctly.
•
Verify that you have used the correct cable type for the connection:
•
For twisted-pair connections to an end node, use straight-through cabling.
•
For fiber-optic connections, verify that the transmit port on the device is connected to the receive port on the connected
device, and that the receive port on the device is connected to the transmit port on the connected device.
•
Verify that the port has not been disabled through a configuration change. You can use the CLI. If you have configured an IP
address on the device, you also can use the Web management interface or IronView Network Manager.
•
If the other procedures do not resolve the problem, try using a different port or a different cable.
Using Virtual Cable Testing to diagnose a cable
FastIron WS devices support Virtual Cable Test (VCT) technology. VCT technology enables you to diagnose a conductor (wire or cable)
by sending a pulsed signal into the conductor, then examining the reflection of that pulse. This method of cable analysis is referred to as
Time Domain Reflectometry (TDR). By examining the reflection, the Brocade device can detect and report cable statistics such as local
and remote link pair, cable length, and link status.
Configuration notes
Refer to these configuration notes when troubleshooting network connections:
•
This feature is supported on copper ports only. It is not supported on fiber ports.
•
The port to which the cable is connected must be enabled when you issue the command to diagnose the cable. If the port is
disabled, the command is rejected.
•
If the port is operating at 100 Mbps half-duplex, the TDR test on one pair will fail.
•
If the remote pair is set to forced 100 Mbps, any change in MDI or MDIX may cause the device to interpret the Multilevel
Threshold-3 (MLT-3) as a reflected pulse, in which case, the device will report a faulty condition. In this case, Brocade
recommends that you run the TDR test a few times for accurate results.
Command syntax
To diagnose a cable using TDR, enter a command such as the following at the Privileged EXEC level of the CLI.
Brocade#phy cable-diag tdr 0/1/1
The above command diagnoses the cable attached to port 0/1/1.
Syntax: phy cable-diag tdr <port-num>
Brocade FastIron WS Hardware Installation Guide 49
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Troubleshooting network connections
Viewing the results of the cable analysis
To display the results of the cable analysis, enter a command such as the following at the Privileged EXEC level of the CLI.
Syntax: show cable-diag tdr <port-num>
Table 2 defines the fields shown in the command output.
Digital Optical Monitoring
You can configure your FWS to monitor optical transceivers in the system, either globally or by specified port. When this feature is
enabled, the system monitors the temperature and signal power levels for the optical transceivers in the specified ports. Console
messages and syslog messages are sent when optical operating conditions fall below or rise above the SFP manufacturer’s
recommended thresholds. For more information about digital optical monitoring, refer to the <Italic>FastIron Configuration Guide
TABLE 2 Cable statistics
This line... Displays...
Port The port that was tested.
Speed The port’s current line speed.
Local pair The local link name.
Pair Length The cable length when terminated, or the distance to the point of fault when the
line is not up.
Remote pair The remote link name.
Pair status The status of the link. This field displays one of the following:
•
Terminated: The link is up.
•
Shorted: A short is detected in the cable.
•
Open: An opening is detected in the cable.
•
ImpedMis: The impedance is mismatched.
•
Failed: The TDR test failed.
Brocade#show cable-diag tdr 0/1/1
Port Speed Local pair Pair Length Remote pair Pair status
--------- ----- ---------- ----------- ----------- -----------
0/1/1 1000M Pair A <50M Pair B Terminated
Pair B <50M Pair A Terminated
Pair C <50M Pair D Terminated
Pair D <50M Pair C Terminated
50 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Connecting Network Devices and Checking Connectivity
Troubleshooting network connections
Brocade FastIron WS Hardware Installation Guide 51
Part Number: 53-1002498-03
Managing the FastIron WS Hardware
Managing FastIron WS temperature settings
The procedures in this manual are for qualified service personnel.
This section describes how to display temperature settings on the device and how to change the temperature warning and shutdown
levels.
Using the temperature sensor on the device
The device comes with three built-in temperature sensors, located on the main board of the device. The temperature sensors cause the
device to generate a Syslog message and SNMP trap if the temperature exceeds a specified warning level or shutdown level. If the
device’s temperature exceeds the safe threshold (shutdown level), the device will reboot.
The software reads the temperature sensors according to the device poll time, which is 60 seconds by default. If the temperature equals
or exceeds the shutdown temperature for five consecutive polls of the temperature by the software, the software will reboot the device to
prevent damage.
You can use the CLI or Web Management Interface to perform the following tasks:
•
Display the temperature of the device
•
Change the warning and shutdown temperature levels
•
Change the device poll time
Displaying the temperature on the FastIron WS
By default, the software polls the temperature sensor every 60 seconds to get the current temperature. This poll rate is controlled by the
device poll time, which also controls how often the software polls other system components.
To display the temperature of a device, enter the following command at any level of the CLI.
52 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Managing the FastIron WS Hardware
Managing FastIron WS temperature settings
Syntax: show chassis
Displaying Syslog messages for temperature on the FastIron WS
The software sends a Syslog message and an SNMP trap if the temperature crosses the warning or shutdown thresholds. The following
methods describe how to view the system log on the device. If you have configured the device to use a Syslog server or SNMP trap
receiver, refer to the documentation for the server or receiver.
Brocade# show chassis
chassis Power supply/fan/temperature
Brocade# show chassis
Power supply 1 (NA - AC - Regular) present, status ok Power supply 2 not present
Fan 1 ok, speed (auto): [[1]]<->2<->3
Fan 2 ok, speed (auto): [[1]]<->2<->3
Fan controlled temperature: 50.5 deg-C
Fan speed switching temperature thresholds:
Speed 1: NM<----->53 deg-C
Speed 2: 37<----->55 deg-C
Speed 3: 50<-----> 90 deg-C (shutdown)
Sensor B Temperature Readings:
Current temperature : 50.5 deg-C
Warning level.......: 55.0 deg-C
Shutdown level......: 90.0 deg-C Sensor A Temperature Readings:
Current temperature : 42.0 deg-C Boot Prom MAC: 001b.ed7e.7040 Management
MAC: 001b.ed7e.7040 Brocade#tempera
temperature temperature sensor commands
Brocade#temperature war
warning Temperature at which the module sends a warning
Brocade#temperature warning 40
Brocade#
!!! Temperature is over warning level !!!
SYSLOG: <9>Jan 1 00:00:00 FWS648G Router System: Temperature 50.0 C degrees,
warning level 40.0 C degrees, shutdown level 90.0 C degrees
SYSLOG: <12>Jan 1 00:00:00 FWS648G Router System: Temperature is over warning
level
Brocade#temper
temperature temperature sensor commands
Brocade# temperature shut 45
Brocade FastIron WS Hardware Installation Guide 53
Part Number: 53-1002498-03
Managing the FastIron WS Hardware
Managing FastIron WS temperature settings
To display the system log, enter the following command at any CLI level.
Changing the temperature warning and shutdown levels
To change the temperature at which the device sends a warning, enter a command such as the following at the Privileged EXEC level of
the CLI.
Brocade#temperature warning 47
Syntax: temperature warning <value>
The <value> can be 0 – 125.
To change the shutdown temperature, enter a command such as the following at Privileged EXEC level of the CLI.
Brocade#temperature shutdown 57
Syntax: temperature shutdown <value>
The <value> can be 0 – 125.
Changing the warning temperature threshold
You can change the warning temperature using the following command. The valid range is 0 – 125
°
C.
The FastIron WS devices will automatically reset and reload the software when the internal temperature reaches or exceeds the configured
shutdown level for five minutes. This release also adds the capability for the system to register negative temperature settings.
To change the temperature at which the device sends a warning, enter a command such as the following at the Privileged EXEC level of
the CLI.
Brocade#temperature warning 47
Syntax: temperature warning <value>
The <value> can be 0 – 125.
Changing the temperature polling interval
The software reads the temperature sensor and polls other hardware sensors according to the value set for the poll time, which is 60
seconds by default. You can change the poll time using the CLI.
Brocade#show log
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
Buffer logging: level ACDMEINW, 8 messages logged
level code: A=alert C=critical D=debugging M=emergency E=error
I=informational N=notification W=warning
Static Log Buffer:
Dynamic Log Buffer (50 entries):
at 0 days 0 hours 2 minutes 0 seconds, level alert
Temperature 48.0 C degrees, warning level 45.0 C degrees, shutdown level 55.0 C
degrees
at 0 days 0 hours 1 minutes 0 seconds, level alert
Temperature 40.0 C degrees, warning level 35.0 C degrees, shutdown level 45.0 C
degrees
54 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Managing the FastIron WS Hardware
Displaying CPU usage
To change the poll time, enter a command such as the following at the global CONFIG level of the CLI.
Brocade(config)#chassis poll-time 200
Syntax: chassis poll-time <value>
The <value> can be 0 – 65535.
Removing MAC address entries
You can remove the following learned MAC address entries from the system MAC address table:
•
All MAC address entries
•
All MAC address entries for a specified Ethernet port
•
All MAC address entries for a specified VLAN
•
A specified MAC address entry in all VLANs
For example, to remove entries for the MAC address 000d.cb80.00d in all VLANs, enter the following command at the Privileged EXEC
level of the CLI.
Brocade#clear mac-address 000d.cb80.00d0
Syntax: clear mac-address <mac-address> | ethernet <port-num> | vlan <number>
If you enter the clear mac-address command without any parameters, the software removes all MAC entries.
Use the <mac-address> parameter to remove a specified MAC address from all VLANs. Specify the MAC address in the following format:
HHHH.HHHH.HHHH.
Use the ethernet <port-num> parameter to remove all MAC addresses for a specified Ethernet port.
Use the vlan <number> parameter to remove all MAC addresses for a specified VLAN.
Displaying CPU usage
You can display the amount of the CHE1 CPU in use. To do so, enter the following command at any level of the CLI.
Syntax: show cpu
Hardware maintenance schedule
The device requires minimal maintenance for its hardware components. Brocade recommends cleaning the fiber-optic connectors on a
fiber-optic port and the connected fiber cable each time you disconnect the cable.
Otherwise, you can replace the following hardware components as needed:
•
Copper and fiber optic modules (SFPs (mini-GBICs))
Brocade#show cpu
31 percent busy, from 3248 sec ago
1 sec avg: 10 percent busy
5 sec avg: 10 percent busy
60 sec avg: 10 percent busy
300 sec avg: 10 percent busy
Brocade FastIron WS Hardware Installation Guide 55
Part Number: 53-1002498-03
Managing the FastIron WS Hardware
Replacing a fiber optic module
Replacing a fiber optic module
You can remove an SFP from a slot and replace it with a new one while the FWS624 is powered on and running.
This section provides information about the following tasks:
•
Removing a fiber optic module
•
Installing a new fiber optic module
•
Cabling a fiber optic module
Removing a fiber optic module
You can remove a fiber SFP (also called a mini-GBIC) from a slot while the device is powered on and running.
Before removing a fiber optic module, have the following on hand:
•
An ESD wrist strap with a plug for connection to the ESD connector on the device.
For safety reasons, the ESD wrist strap should contain a series 1 meg ohm resistor.
Remove a fiber optic module from an SFP slot.
1. Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack).
2. Disconnect the fiber cable connector from the port connector.
3. Pull the fiber optic module out of the port by pulling the bail latch forward, away from the front panel of the module. This unlocks
the module from the front panel.
NOTE
The bail latch may be attached to either the top or the bottom of the mini-GBIC.
4. Grasping the bail latch, pull the fiber optic module out of the port.
5. Store the fiber optic module in a safe, static-free place or in an anti-static bag.
1 Bail latch
1
56 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Managing the FastIron WS Hardware
Cabling a fiber optic module
6. Install a new fiber optic module in the port. For information about performing this task, refer to “Installing a new fiber optic
module”.
Installing a new fiber optic module
For instruction on installing a fiber optic module refer to “Installing a fiber optic module” on page 45.
Cabling a fiber optic module
For instruction on cabling a fiber optic module refer to “Cabling a fiber optic module” on page 46.
Cleaning the fiber-optic connectors
For instruction on cleaning a fiber optic module refer to “Cleaning the fiber-optic connectors” on page 46.
Brocade FastIron WS Hardware Installation Guide 57
Part Number: 53-1002498-03
Hardware Specifications
Hardware specifications for FastIron WS models
Physical dimensions and weight
The following sections list the physical dimensions and weight for the FastIron WS family of switches and redundant power supplies.
FastIron WS family of switches
The following tables list the physical dimensions and weight for the FastIron WS family of switches.
Redundant power supplies
The following tables list the physical dimensions and weight for the redundant power supplies.
Table 5 lists the physical dimensions and weight of the RPS2-EIF Redudant Power Supply.
Table 6 lists the physical dimensions and weight of the RPS12 External Redundant Power Supply.
TABLE 1 Physical dimensions and weight of the FWS624, FWS624G
Platform Height Width Depth Weight
FWS624,
FWS624G
4.34 cm
1.7 in
44 cm
17.32 in
35 cm
13.78 in
•
4.1 kg(9 lbs )
TABLE 2 Physical dimensions and weight of the FWS648, FWS648G
Platform Height Width Depth Weight
FWS648,
FWS648G
4.34 cm
1.7 in
44 cm
17.32 in
35 cm
13.78 in
•
4.5 kg (10.8 lbs)
TABLE 3 Physical dimensions and weight of the FWS624-PoE, FWS624G-PoE
Platform Height Width Depth Weight
FWS624-PoE,
FWS624G-PoE
4.34 cm
1.7 in
44 cm
17.32 in
35 cm
13.78 in
•
4.9 kg (10.8 lbs)
TABLE 4 Physical dimensions and weight of the FWS648-PoE, FWS648G-PoE
Platform Height Width Depth Weight
FWS648-PoE,
FWS648G-PoE
4.34 cm
1.7 in
44 cm
17.32 in
35 cm
13.78 in
•
5.3 kg (11.7 lbs)
TABLE 5 Physical dimensions and weight of the RPS2-EIF power supply
Power supply Height Width Depth Weight
RPS2-EIF 4.3 cm
1.69 in
44 cm
17.32 in
28.4 cm
11.18 in
•
5.5kg (12.13 lbs.)
58 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Hardware Specifications
Hardware specifications for FastIron WS models
Environmental considerations
For optimal performance, operate or store your Brocade device in compliance with the following environmental conditions.
Operating environment
Table 7 provides the operating environment specifications for the FastIron WS.
•
Maximum BTUs:
•
FWS624 and FWS648: 100 watts (340 BTU/Hr) per power supply
Storage environment
Table 8 provides the storage environment specifications for the FastIron WS.
Cooling system and fans
The cooling fans cool the CPU, main memory, and voltage regulators. The fans use either a push or pull configuration to move the air
from the right side of the device to the left side of the device:
•
Total cooling capacity: 80 to 100 watts
•
Total air flow: 200 LFM
•
Operating noise: < 50 dB-A (non-POE models)
•
Operating noise: < 55 dB-A (POE models)
NOTE
Operating noise is based on the ISO 7779 standard.
TABLE 6 Physical dimensions and weight of the RPS12 power supply
Power supply Height Width Depth Weight
RPS12 4.3 cm
1.69 in
44 cm
17.32 in
32.3 cm
12.71 in
•
5.48kg (12.08 lbs.)
TABLE 7 Operating environment
Operating temperature Relative humidity Operating altitude
0
°
– 40
°
C (32
°
– 104
°
F) 40
°
C (5 to 95%, @ 104.9
°
F),
non-condensing
0 – 2000 meters (0 – 6,600 ft )
TABLE 8 Storage environment
Storage temperature Storage humidity Storage altitude
-40
°
to 70
°
C, -40
°
to 158
°
F 95% maximum, non-condensing 3,000 meter (10,000 feet )
maximum
Brocade FastIron WS Hardware Installation Guide 59
Part Number: 53-1002498-03
Hardware Specifications
Hardware specifications for FastIron WS models
The following figure shows the airflow.
FIGURE 1 FastIron WS FWS624 airflow
For a complete list of Regulatory Compliances refer to “Russia” on page 56
Pinouts and signalling
This section lists the pinouts for the DB-9 connector and RJ-45 port jacks.
Serial (console) port pinouts
The Console port is a standard male DB-9 connector, as shown in the following figure
Most PC serial ports require a cable with a female DB-9 connector. However, terminal connections will vary, requiring a cable with either a
DB-9 or DB-25 connector, male or female.
Serial cable options between the FastIron WS and a PC or terminal are shown in Figure 2.
NOTE
As indicated in Figure 2 and Figure 3, some of the wires should not be connected. If you do connect the wires that are labeled
“Reserved”, you might get unexpected results with some terminals.
Air inlet
Air exhaust
6 9
15
60 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Hardware Specifications
Hardware specifications for FastIron WS models
FIGURE 2 Console port pin assignments showing cable connection options to a terminal or PC
FIGURE 3 Pin assignment and signalling for 10/100BaseTX and 1000BaseT ports
Cable specifications
Table 9 lists the cable specifications for the cables used with the 10/100 Ethernet ports.
NOTE
Cable installation and network configuration will affect overall transmission capability. The numbers provided below represent the
accepted recommendations of the various standards. For network-specific recommendations, consult your local Brocade reseller
or system engineer.
TABLE 9 Cable length summary table
Cable type Connector type Core diameter
(microns)
Modal bandwidth
(MHz*km) or
wavelength (nm)
Range (meters)
1000Base-BX-D Single-mode Fiber
(SMF)
LC connector for SFP
module
9 1490 nm 2 – 10000 (10km)
1000Base-BX-U SMF LC connector for SFP
module
9 1310 nm 2 – 10000 (10km)
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
8
3
2
20
7
6
4
5
22
Reserved
DB-9 to DB-9
Female Switch
DB-9 to DB-25
Female Switch
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Terminal or PC Terminal or PC
Pin Number
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
81
18
RD+
RD-
TD+
Not used
TD-
Not used
Not used
Not used
RD+
RD-
TD+
CMT
TD-
CMT
CMT
CMT
Pin Assignment MDI-X ports MDI-X ports
10BaseT
Pin Number
100BaseTX and 1000BaseT
Brocade FastIron WS Hardware Installation Guide 61
Part Number: 53-1002498-03
Hardware Specifications
Hardware specifications for FastIron WS models
Power cords
All of the FastIron WS devices ship with US-compatible power cords unless otherwise specified at the time of order. United Kingdom-
and European-compatible power cords are also available.
1000Base-LHA SMF LC connector for SFP
module
9 1550 nm 2 – 70000 (70km)
1000Base-LHB SMF LC connector for SFP
module
9 1550 nm 2 – 120000 (120km)
1000Base-LX Multi-mode Fiber
(MMF)
LC connector for SFP
module
62.5 500 2 – 550
MMF 50 400 2 – 550
MMF 50 500 2 – 550
SMF 9 1300 nm 2 – 10000
1000Base-SX MMF LC connector for SFP
module
62.5/125 200 .5 – 275
MMF 62.5/125 500 .5 – 550
MMF 50/125 900 .5 – 595
MMF 50/125 1500 .5 – 740
MMF 50/125 2000 .5 – 860
1000Base-SX 2 MMF LC connector for SFP
module
62.5 500 up to 2000
(2 km)
1000Base-T Copper RJ-45 jack for
standard unshielded
twisted pair (UTP or
Category 5)
n/a n/a up to 100 meters
100Base-BX
100Bse-BX-D
SMF LC connector for SFP
module
9 1310/1490 10000 (10 km)
100Base-FX MMF LC connector for SFP
module
62.5 500 up to 2000
(2 km)
100Base-FX-IR MMF SC 62.5 125 2 km (1.24 miles)
100Base-FX-LR SMF SC 9 125 20 km
(12.43 miles)
100Base-TX Copper RJ-45 jack for
standard unshielded
twisted pair (UTP or
Category 5)
n/a n/a up to 100 meters
10Base-TX Copper RJ-45 jack for
standard unshielded
twisted pair (UTP or
Category 5)
n/a n/a up to 100 meters
TABLE 9 Cable length summary table (Continued)
Cable type Connector type Core diameter
(microns)
Modal bandwidth
(MHz*km) or
wavelength (nm)
Range (meters)
62 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Hardware Specifications
Hardware specifications for FastIron WS models
AC power supply specifications
The FastIron WS switches include an integrated AC power supply:
•
standard IEC type (IEC320) input connector
•
operating 90 VAC to 264 VAC input, universal/wide input
Specifications
Power specifications for POE
The implementation of the 802.3af standard limits power to 15.4W (44V to 57V) from the power sourcing device. This limit complies
with safety standards and existing wiring limitations. Though limited by the 802.3af standard, 15.4 watts of power is ample, as most
powered devices consume an average of 5 to 12 watts of power. IP phones, wireless LAN access points, and network surveillance
cameras each consume an average of 3.5 to 9 watts of power.
Brocade 48-volt power supplies provide power to the POE daughter card, and ultimately to POE power-consuming devices. The
number of POE power-consuming devices that one 48-volt power supply can support depends on the number of watts required by each
device. Each 48-volt power supply provides 410 watts of power for POE, and each POE port supports a maximum of 15.4 watts of
power per POE power-consuming device. For example, if each POE power-consuming device attached to the FWS consumes 12 watts
of power, one 48-volt supply will power up to 34 POE ports.
If your FastIron WS chassis has 48 ports, and each POE-enabled port needs 15.4 watts, then a maximum of 26 ports can supply power
to connected devices.
For power supply specifications, refer to “AC power supply specifications” on page 62. For POE configuration procedures, refer to the
<Italic>FastIron Configuration Guide.
TABLE 10 Specifications for AC power
Property FWS624, FWS624G FWS648, FWS648G FWS624-PoE,
FWS624G-PoE
FWS648-PoE,
FWS648G-PoE
Input voltage range 100 – 240 VAC 100 – 240 VAC 100 – 240 VAC 100 – 240 VAC
Input current < 2 Amps < 2 Amps < 10 Amps < 10 Amps
Inrush current < 60 Amps peak
maximum
< 60 Amps peak
maximum
< 75 Amps peak
maximum
< 75 Amps peak maximum
Power consumption 31 W 63 W MB: 41 W
POE: < 410 W
MB: 73 W
POE: < 410 W
Max output power 65 W 100 W 530 W 530 W
Brocade FastIron WS Hardware Installation Guide 63
Part Number: 53-1002498-03
Troubleshooting
Diagnosing switch indicators
Power and cooling problems
If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or
internal power supply. However, if the unit powers off after running for a while, check for loose power connections, power losses or surges
at the power outlet, and verify that the fans on the unit are unobstructed and running prior to shutdown. If you still cannot isolate the
problem, then the internal power supply may be defective. In this case, contact Technical Support for assistance.
Installation
Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (such as the
power cord or network cabling), test them in an alternate environment where you are sure that all the other components are functioning
properly.
In-band access
You can access the management agent in the switch from anywhere within the attached network using Telnet, a Web browser, or other
network management software. However, you must first configure the switch with a valid IP address, subnet mask, and default gateway. If
you have trouble establishing a link to the management agent, check to see if you have a valid network connection. Then verify that you
entered the correct IP address. Also, be sure the port through which you are connecting to the switch has not been disabled. If it has not
been disabled, then check the network cabling that runs between your remote location and the switch.
TABLE 1 Troubleshooting chart
Symptom Action
Power LED is Off
•
Internal power supply is disconnected.
•
Check connections between the switch, the power cord, and the wall outlet.
•
Contact Technical Support.
Power LED is Amber
•
Internal power supply has failed. Contact Technical Support.
Diag LED is Amber
•
The switch’s self test has detected a fault.
•
Power cycle the switch to try and clear the condition. If the condition
persists, contact Technical Support.
Link LED is Off
•
Verify that the switch and attached device are powered on.
•
Be sure the cable is plugged into both the switch and corresponding device.
•
Verify that the proper cable type is used and its length does not exceed
specified limits.
•
Check the adapter on the attached device and cable connections for
possible defects. Replace the defective adapter or cable if necessary.
(RPS2-EIF and RPS12) Link
LED is Off
•
The port does not have a valid connection to the switch.
•
Check connections between the switch, the power cord, and the wall outlet.
(RPS2-EIF and RPS12) Link
LED is Amber
•
Primary power supply is active. RPS is on standby.
(RPS2-EIF and RPS12) Activity
LED is Green
•
Primary power supply is off. RPS is now active
64 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Troubleshooting
Diagnosing switch indicators
Brocade FastIron WS Hardware Installation Guide 65
Part Number: 53-1002498-03
Regulatory Statements
USA (FCC CFR 47 part 15 warning)
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications made to this device which are not expressly approved by Brocade could void the
user’s authority to operate the equipment.
Industry Canada statement
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
English Translation of above statement
This Class A digital apparatus complies with Canadian ICES-003.
Europe and Australia (CISPR 22 class A warning)
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to
take adequate measures.
Japan (VCCI)
English translation of above statement
This is Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment
(VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be
required to take corrective actions.
66 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Regulatory Statements
Japan power cord
Japan power cord
English translation of above statement
ATTENTION: Never use the power cord packed with your equipment for other products.
Korea
English Translation of Above Statement
This apparatus has radio wave acceptability registration as a Class A device, so sellers or users should be aware of this. If it is sold or
purchased incorrectly, it should be exchanged with a home apparatus (Class B).
Russia
English translation of above statement
Certificate of Conformity in "Certification System in the field of telecommunications" # ??-2-???-0560, validity from the 29 of October
2009 to the 29 of October 2012.
ɋɟɪɬɢɮɢɤɚɬ ɋɨɨɬɜɟɬɫɬɜɢɹ ɜ "Cɢɫɬɟɦɟ ɫɟɪɬɢɮɢɤɚɰɢɢ ɜ ɨɛɥɚɫɬɢ ɫɜɹɡɢ" ʋ Ɉɋ-2-ɋɉȾ-0560,
ɫɪɨɤ ɞɟɣɫɬɜɢɹ: ɫ 29 ɨɤɬɹɛɪɹ 2009 ɝ. ɞɨ 29 ɨɤɬɹɛɪɹ 2012 ɝ.
Brocade FastIron WS Hardware Installation Guide 67
Part Number: 53-1002498-03
Regulatory Statements
China
China
汉文　 “仅适用于非热带气候条件下安全使用。”　
藏文　
蒙古
文
壮文　
Dan hab yungh youq gij dienheiq diuzgen mbouj dwg diegndat
haenx ancienz sawjyungh.
安全
说明
和标
记　
维文　
汉文　 仅适用于海拔２０００ｍ以下地区安全使用。
藏文　
蒙古
文　
壮文　
Dan hab yungh youq gij digih haijbaz 2000m doxroengz
haenx ancienz sawjyungh.
安全
说明
和标
记　
维文　
在维修的时候一定要断开所有电源　(English translation“disconnect all power sources before service”)
For non tropical use:
For altitude 2000 meter and below:
China-CCC Warning statements
English translation of above statement
This is a Class A product. In a domestic environment this product may cause radio interference, in
which case the user may be required to take adequate measures.
Warning for Class A:
68 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Regulatory Statements
BSMI statement (Taiwan)
BSMI statement (Taiwan)
English translation of above statement
Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
Regulatory compliance
Table 1 lists the Electromagnetic Compatibility (EMC), Immunity standards, and safety agency approvals for the FastIron family of
switches.
TABLE 1 Regulatory compliance and safety approvals
Certifications
Emissions:
•
ICES-003, Electromagnetic Emission
•
FCC Part 15 Class A
•
EN 55022/CISPR 22 Class A
•
VCCI Class A
•
EN 61000-3-2, Power Line Harmonics
•
EN 61000-3-3, Voltage Fluctuation & Flicker
•
EN 61000-6-3, Electromagnetic Compatibility, Generic Standard
•
AS/NZS CISPR 22, Electromagnetic Compatibility
Immunity:
•
EN 61000-6-1, Electromagnetic Compatibility, Generic Standard
•
EN 55024, Information Technology equipment - Immunity
Characteristics
Safety:
•
BI-NAT CSA 60950-1-03/UL 60950-1
•
EN 60950-1:2001
•
IEC 60950-1:2001
RoHS Compliance:
•
Complies with the EU standard 2002/95/EC
Brocade FastIron WS Hardware Installation Guide 69
Part Number: 53-1002498-03
Caution and Danger Notices
The caution and danger notices that appear in this manual are listed below in English, German, French, and Spanish.
Cautions
A caution calls your attention to a possible hazard that can damage equipment.
“Vorsicht” weist auf die Gefahr einer möglichen Beschädigung des Gerätes in.
Une mise en garde attire votre attention sur un risque possible d'endommagement de l'équipement. Ci-dessous, vous trouverez les
mises en garde utilisées dans ce manuel.
Un mensaje de precaución le advierte sobre un peligro posible que pueda dañar el equipo. Las siguientes son precauciones utilizadas en
este manual.
Table 0.1:
CAUTION Do not install the device in an environment where the operating ambient temperature might
exceed 40° C (104° F).
VORSICHT Das Gerät darf nicht in einer Umgebung mit einer Umgebungsbetriebstemperatur von über
40° C (104° F) installiert werden.
MISE EN GARDE N'installez pas le dispositif dans un environnement où la température d'exploitation ambiante
risque de dépasser 40° C (104° F).
PRECAUCIÓN No instale el instrumento en un entorno en el que la temperatura ambiente de operación
pueda exceder los 40°C (104°F).
Table 0.2:
CAUTION Make sure the air flow around the front, sides, and back of the device is not restricted.
VORSICHT Stellen Sie sicher, dass an der Vorderseite, den Seiten und an der Rückseite der Luftstrom
nicht behindert wird.
MISE EN GARDE Vérifiez que rien ne restreint la circulation d'air devant, derrière et sur les côtés du dispositif et
qu'elle peut se faire librement.
PRECAUCIÓN Asegúrese de que el flujo de aire en las inmediaciones de las partes anterior, laterales y
posterior del instrumento no esté restringido.
Table 0.3:
CAUTION Use a separate branch circuit for each AC power cord, which provides redundancy in case
one of the circuits fails.
VORSICHT Es empfiehlt sich die Installation eines separaten Stromkreiszweiges für jede
Wechselstrom-Elektroschnur als Redundanz im Fall des Ausfalls eines Stromkreises.
MISE EN GARDE Utilisez un circuit de dérivation différent pour chaque cordon d’alimentation C.A. Ainsi, il y
aura un circuit redondant en cas de panne d’un des circuits.
PRECAUCIÓN Use un circuito derivado separado para cada cordón de alimentación de CA, con lo que se
proporcionará redundancia en caso de que uno de los circuitos falle.
70 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Caution and Danger Notices
Cautions
Table 0.4:
CAUTION Ensure that the device does not overload the power circuits, wiring, and over-current
protection. To determine the possibility of overloading the supply circuits, add the ampere
(amp) ratings of all devices installed on the same circuit as the device. Compare this total with
the rating limit for the circuit. The maximum ampere ratings are usually printed on the
devices near the input power connectors.
VORSICHT Stromkreise, Verdrahtung und Überlastschutz dürfen nicht durch das Gerät überbelastet
werden. Addieren Sie die Nennstromleistung (in Ampere) aller Geräte, die am selben
Stromkreis wie das Gerät installiert sind. Somit können Sie feststellen, ob die Gefahr einer
Überbelastung der Versorgungsstromkreise vorliegt. Vergleichen Sie diese Summe mit der
Nennstromgrenze des Stromkreises. Die Höchstnennströme (in Ampere) stehen
normalerweise auf der Geräterückseite neben den Eingangsstromanschlüssen.
MISE EN GARDE Assurez-vous que le dispositif ne risque pas de surcharger les circuits d'alimentation, le
câblage et la protection de surintensité. Pour déterminer le risque de surcharge des circuits
d'alimentation, additionnez l'intensité nominale (ampères) de tous les dispositifs installés sur
le même circuit que le dispositif en question. Comparez alors ce total avec la limite de charge
du circuit. L'intensité nominale maximum en ampères est généralement imprimée sur chaque
dispositif près des connecteurs d'entrée d'alimentation.
PRECAUCIÓN Verifique que el instrumento no sobrecargue los circuitos de corriente, el cableado y la
protección para sobrecargas. Para determinar la posibilidad de sobrecarga en los circuitos de
suministros, añada las capacidades nominales de corriente (amp) de todos los instrumentos
instalados en el mismo circuito que el instrumento. Compare esta suma con el límite nominal
para el circuito. Las capacidades nominales de corriente máximas están generalmente
impresas en los instrumentos, cerca de los conectores de corriente de entrada.
Table 0.5:
CAUTION Use the erase startup-config command only for new systems. If you enter this command
on a system you have already configured, the command erases the configuration. If you
accidentally do erase the configuration on a configured system, enter the write memory
command to save the running configuration to the startup-config file.
VORSICHT Verwenden Sie den Befehl "Erase startup-config" (Löschen Startup-Konfig) nur für neue
Systeme. Wenn Sie diesen Befehl in ein bereits konfiguriertes System eingeben, löscht der
Befehl die Konfiguration. Falls Sie aus Versehen die Konfiguration eines bereits
konfigurierten Systems löschen, geben Sie den Befehl "Write Memory" (Speicher schreiben)
ein, um die laufende Konfiguration in der Startup-Konfig-Datei zu speichern.
MISE EN GARDE N'utilisez la commande erase startup-config que pour les nouveaux systèmes. Si vous
entrez cette commande sur un système que vous avez déjà configuré, elle efface la
configuration. Si vous effacez la configuration par accident sur un système configuré, entrez
la commande write memory pour enregistrer la configuration actuelle dans le fichier
startup-config.
PRECAUCIÓN Use el comando erase startup-config (borrar configuración de inicio) para sistemas nuevos
solamente. Si usted introduce este comando en un sistema que ya ha configurado, el
comando borrará la configuración. Si usted borra accidentalmente la configuración en un
sistema ya configurado, introduzca el comando write memory (escribir memoria) para
guardar la configuración en ejecución en el archivo startup-config.
Table 0.6:
CAUTION Never leave tools inside the chassis.
VORSICHT Lassen Sie keine Werkzeuge im Chassis zurück.
MISE EN GARDE Ne laissez jamais d'outils à l'intérieur du châssis.
PRECAUCIÓN No deje nunca herramientas en el interior del chasis.
Brocade FastIron WS Hardware Installation Guide 71
Part Number: 53-1002498-03
Caution and Danger Notices
Danger
Danger
A danger calls your attention to a possible hazard that can cause injury or death. The following are the danger notices used in this manual.
"Gefahr" weist auf eine mögliche Gefährdung hin, die zu Verletzungen oder Tod führen können. Sie finden die folgenden Warnhinweise in
diesem Handbuch:
Un danger attire votre attention sur un risque possible de blessure ou de décès. Ci-dessous, vous trouverez les Dangers utilisés dans ce
manuel.
Una peligro le llama la atención sobre cualquier peligro posible que pueda ocasionar daños personales o la muerte. A continuación se dan
las advertencias utilizadas en este manual.
Table 0.7:
CAUTION Changes or modifications made to this device that are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
VORSICHT Falls dieses Gerät verändert oder modifiziert wird, ohne die ausdrückliche Genehmigung der
für die Einhaltung der Anforderungen verantwortlichen Partei einzuholen, kann dem
Benutzer der weitere Betrieb des Gerätes untersagt werden.
MISE EN GARDE Les éventuelles modifications apportées à cet équipement sans avoir été expressément
approuvées par la partie responsable d'en évaluer la conformité sont susceptibles d'annuler
le droit de l'utilisateur à utiliser cet équipement.
PRECAUCIÓN Si se realizan cambios o modificaciones en este dispositivo sin la autorización expresa de la
parte responsable del cumplimiento de las normas, la licencia del usuario para operar este
equipo puede quedar anulada.
Table 0.8:
CAUTION Remove the power cord from a power supply before you install it in or remove it from the
device. Otherwise, the power supply or the device could be damaged as a result. (The
device can be running while a power supply is being installed or removed, but the power
supply itself should not be connected to a power source.)
VORSICHT Vor dem Installieren einer Stromversorgung im Gerät bzw. vor dem Herausnehmen einer
Stromversorgung aus dem Gerät das Netzkabel von der Stromversorgung trennen.
Geschieht das nicht, kann dies zur Beschädigung der Stromversorgung bzw. des Geräts
führen. (Die Stromversorgung kann im laufenden Gerätebetrieb herausgenommen bzw.
installiert werden, sollte dabei aber nicht an einer Stromquelle angeschlossen sein.)
MISE EN GARDE Débrancher le cordon secteur de l'alimentation avant de le la raccorder à l'équipement ou de
le la déconnecter de celui-ci, faute de quoi le circuit d'alimentation de l'équipement pourrait
être endommagé. (L'équipement peut fonctionner pendant la dépose ou le remplacement
d'une alimentation électrique, mais il est important que celle-ci ne soit pas raccordée au
secteur.)
PRECAUCIÓN Desenchufe el cable eléctrico de una fuente de alimentación antes de proceder a montarla o
a desmontarla del dispositivo. En caso contrario, la fuente de alimentación o el dispositivo
podrían sufrir daños. (Aunque el dispositivo podrá mantenerse en funcionamiento durante la
instalación o desinstalación de la fuente de alimentación, dicha fuente de alimentación no
deberá estar conectada a una toma de corriente).
72 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Caution and Danger Notices
Danger
Table 0.11:
DANGER The procedures in this manual are for qualified service personnel.
GEFAHR Die Verfahren in diesem Handbuch sind nur für qualifiziertes Wartungspersonal gedacht.
DANGER Les procédures décrites dans ce manuel doivent être effectuées par le personnel de service
qualifié uniquement.
PELIGRO Los procedimientos de este manual se han hecho para personal de servicio cualificado.
Table 0.12:
DANGER Before beginning the installation, refer to the precautions in “Power precautions” on
page 21.
GEFAHR Vor der Installation siehe Vorsichtsmaßnahmen unter " Power Precautions "
(Vorsichtsmaßnahmen in Bezug auf elektrische Ablagen) auf den Seiten page 21.
DANGER Avant de commencer l'installation, consultez les précautions décrites dans " Power
Precautions " (Précautions quant à l'alimentation), page 21.
PELIGRO Antes de comenzar la instalación, consulte las precauciones en la sección " Power
Precautions" (Precauciones sobre corriente) que se encuentra en las páginas page 21.
Table 0.13:
DANGER All fiber optic interfaces use Class 1 lasers.
GEFAHR Alle Glasfaser-Schnittstellen verwenden Laser der Klasse 1.
DANGER Toutes les interfaces en fibres optiques utilisent des lasers de classe 1.
PELIGRO Todas las interfaces de fibra óptica utilizan láser de clase 1.
Table 0.14:
DANGER Make sure the rack or cabinet housing the device is adequately secured to prevent it from
becoming unstable or falling over.
GEFAHR Stellen Sie sicher, dass das Gestell oder der Schrank für die Unterbringung des Geräts auf
angemessene Weise gesichert ist, so dass das Gestell oder der Schrank nicht wackeln oder
umfallen kann.
DANGER Vérifiez que le bâti ou le support abritant le dispositif est bien fixé afin qu'il ne devienne pas
instable ou qu'il ne risque pas de tomber.
PELIGRO Verifique que el bastidor o armario que alberga el instrumento está asegurado
correctamente para evitar que pueda hacerse inestable o que caiga.
Table 0.15:
DANGER Mount the devices you install in a rack or cabinet as low as possible. Place the heaviest
device at the bottom and progressively place lighter devices above.
GEFAHR Montieren Sie die Geräte im Gestell oder Schrank so tief wie möglich. Platzieren Sie das
schwerste Gerät ganz unten, während leichtere Geräte je nach Gewicht (je schwerer desto
tiefer) darüber untergebracht werden.
DANGER Montez les dispositifs que vous installez dans un bâti ou support aussi bas que possible.
Placez le dispositif le plus lourd en bas et le plus léger en haut, en plaçant tous les
dispositifs progressivement de bas en haut du plus lourd au plus léger.
PELIGRO Monte los instrumentos que instale en un bastidor o armario lo más bajos posible. Ponga el
instrumento más pesado en la parte inferior y los instrumentos progresivamente más
livianos más arriba.
Brocade FastIron WS Hardware Installation Guide 73
Part Number: 53-1002498-03
Caution and Danger Notices
Danger
Table 0.16:
DANGER Disconnect the power cord from all power sources to completely remove power from the
device.
GEFAHR Ziehen Sie das Stromkabel aus allen Stromquellen, um sicherzustellen, dass dem Gerät
kein Strom zugeführt wird.
DANGER Débranchez le cordon d'alimentation de toutes les sources d'alimentation pour couper
complètement l'alimentation du dispositif.
PELIGRO Para desconectar completamente la corriente del instrumento, desconecte el cordón de
corriente de todas las fuentes de corriente.
Table 0.17:
DANGER If the installation requires a different power cord than the one supplied with the device, make
sure you use a power cord displaying the mark of the safety agency that defines the
regulations for power cords in your country. The mark is your assurance that the power cord
can be used safely with the device.
GEFAHR Falls für die Installation ein anderes Stromkabel erforderlich ist (wenn das mit dem Gerät
gelieferte Kabel nicht passt), müssen Sie sicherstellen, dass Sie ein Stromkabel mit dem
Siegel einer Sicherheitsbehörde verwenden, die für die Zertifizierung von Stromkabeln in
Ihrem Land zuständig ist. Das Siegel ist Ihre Garantie, dass das Stromkabel sicher mit Ihrem
Gerät verwendet werden kann.
DANGER Si l'installation nécessite un cordon d'alimentation autre que celui fourni avec le dispositif,
assurez-vous d'utiliser un cordon d'alimentation portant la marque de l'organisation
responsable de la sécurité qui définit les normes et régulations pour les cordons
d'alimentation dans votre pays. Cette marque vous assure que vous pouvez utiliser le
cordon d'alimentation avec le dispositif en toute sécurité.
PELIGRO Si la instalación requiere un cordón de corriente distinto al que se ha suministrado con el
instrumento, verifique que usa un cordón de corriente que venga con la marca de la agencia
de seguridad que defina las regulaciones para cordones de corriente en su país. Esta marca
será su garantía de que el cordón de corriente puede ser utilizado con seguridad con el
instrumento.
Table 0.18:
DANGER For safety reasons, the ESD wrist strap should contain a series 1 meg ohm resistor.
GEFAHR Aus Sicherheitsgründen sollte ein EGB-Armband zum Schutz von elektronischen
gefährdeten Bauelementen mit einem 1 Megaohm-Reihenwiderstand ausgestattet sein.
DANGER Pour des raisons de sécurité, la dragonne ESD doit contenir une résistance de série 1
méga ohm.
PELIGRO Por razones de seguridad, la correa de muñeca ESD deberá contener un resistor en serie
de 1 mega ohmio.
Table 0.19:
DANGER Do not place an RPS unit on the floor as the case is not waterproof. It is recommended that
either of the RPS units be installed in a network equipment rack
GEFAHR Eine RPS-Einheit darf NICHT auf den Fußboden gestellt werden, da das Gehäuse nicht
wasserdicht ist. Es wird empfohlen, dass RPS-Einheiten in einem Rack für Netzwerkgeräte
installiert werden.
DANGER NE PAS placer une alimentation stabilisée directement sur le sol, car son boîtier n'est pas
étanche. Il est recommandé d'installer les unités d'alimentation stabilisée dans un rack.
PELIGRO NO coloque la unidad RPS en el suelo, pues la carcasa no es impermeable. Se recomienda
la instalación de alguna de las unidades RPS en un armazón para equipos de red.
74 Brocade FastIron WS Hardware Installation Guide
Part Number: 53-1002498-03
Caution and Danger Notices
Danger

Navigation menu