RuggON PM-521 TABLET PC User Manual PM 521 UM DF D 003092015

RuggON Corporation TABLET PC PM 521 UM DF D 003092015

User manual revised 2

                                 PM-521 User's Manual
                                                      ©2015 RuggON Corporation. All rights reserved. TRADEMARKS RuggON logo is a trademark of RuggON Corporation, registered in the United States Patent and Trademark Office and in other countries. Microsoft and the Windows logo are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Microsoft products are licensed to OEMs by Microsoft Licensing, Inc., a wholly owned subsidiary of Microsoft Corporation. The Bluetooth®  word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.  Images shown in this document may vary slightly from actual products at time of shipping. Information in this manual is subject to change without notice.
i Table of Contents   About This Manual Related Information ......................................................................................1  Conventions..................................................................................................1   Basic Safety Guidelines Intended Use ................................................................................................2  Maintenance and Operation Overview .........................................................2  Safety ...........................................................................................................3  Electrical Hazards.........................................................................................3  Environmental...............................................................................................3  Radio Transmissions ....................................................................................4  Cleaning and Servicing.................................................................................4  Regulatory and Certification .........................................................................4  Lithium Battery Safety Statement .................................................................5   Chapter 1.  Introduction About This Guide ..........................................................................................7  Unpacking the Device...................................................................................7  Technical Specifications ...............................................................................7  PM-521 Configuration Options .....................................................................9  Parts List.....................................................................................................10  Identifying the Device ................................................................................. 11  Dimensions .................................................................................................16  Touch Screen Features ..............................................................................17   Chapter 2.  Getting Started First Time Use ............................................................................................18  Charging the Battery...................................................................................18  Powering the Device On and Off ................................................................19  Installing the MicroSD Card ........................................................................22  Removing the MicroSD Card ......................................................................23  Using the Stylus..........................................................................................24
ii  Removing the Protective Film from the Display..........................................24   Chapter 3.  Operation Opening the I/O Compartment Cover .........................................................25  Closing the I/O Compartment Cover ..........................................................26  Connecting to External Cabling ..................................................................27  Handstrap, Carrying Handle and Shoulder Strap .......................................30  Installing the Standard Battery ...................................................................34  Removing the Standard Battery .................................................................35  Connecting to a Wireless Network .............................................................36   Chapter 4.  Using BIOS Setup Utility When to Use the BIOS Setup Utility ...........................................................37  Accessing the BIOS Setup Utility ...............................................................37  Installation an Operating System................................................................38  BIOS Passwords ........................................................................................41  EC and BIOS ..............................................................................................43   Chapter 5.  Troubleshooting Troubleshoot the Wi-Fi Connection ............................................................48  Troubleshoot Operating the Computer .......................................................49  Call Product Support ..................................................................................49   Chapter 6.  Maintenance Cleaning the Device ...................................................................................50  Returning the Device ..................................................................................50  Contacting RuggON ...................................................................................50
1 About This Manual  The PM-521 User’s Manual provides instruction for qualified personnel to follow when setting up a new PM-521 device.  This document is intended for use by qualified personnel to compliment the training and expertise, not to replace it.  Related Information  Current information and manuals are available for download at the following website:  http://www.ruggon.com  Conventions  Bolded or underlined text is used to emphasize the designated information.   A Note is used to provide additional information for the device or settings.    A Caution is used to warn against potential hazards or to caution against unsafe practices.    A Warning is used to identify immediate hazards for property damage, injury or death.
2  Basic Safety Guidelines  The following safety guidelines are intended to help protect the user from injury and prevent damage to the hardware.  Do not place anything on the AC adapters power cable and make sure the cable is not located where it can be tripped over or stepped on.  Do not cover the AC adaptor as it reduces the cooling  Do not use the AC adapter while it is inside the carrying case.  Use only the AC adapter, power cord, and batteries that are approved for use with the device. Use of another type of battery or AC adapter may cause risk of fire or explosion.  If you use an extension cable with the AC adapter, ensure that the total ampere rating of all products plugged in to the extension cable does not exceed the ampere rating of the extension cable.  If the device is moved between environments with very different temperature and/ or humidity ranges, condensation may form on or within the device. Avoid damaging the device by allowing sufficient time for the moisture to evaporate before using the device.  When disconnecting cables, pull on the connector or on its strain relief loop, not on the cable itself. When pulling out or plugging in the connector, keep it evenly aligned to prevent bending the connector pins.  Intended Use  The PM-521 rugged tablet is equipped with multi-functional terminals for stationary and mobile applications in industrial environments such as logistics, warehousing, fleet management, manufacturing and the automotive industry.  Read the safety guidelines thoroughly before starting any servicing on the device. Read the guidelines before powering up the device, and keep this document for later use.  The operator is solely responsible for any damage resulting from unauthorized modifications to the device.  Unintended Application Use  The device is not designed for use in life-support systems or critical safety/security systems where system malfunction can lead to the direct or indirect endangerment of human life. The operator is fully responsible for using the device in these situations.  Maintenance and Operation Overview  The PM-521 is designed and manufactured according to strict controls and following the stated safety regulations. The following list identifies incorrect operating uses of the PM-521. Incorrect use of the PM-521 can lead to hardware damage, safety issues and possible risk to personnel health:  The PM-521 is under operation by untrained personnel;  The PM-521 is not maintained as recommended;  The PM-521 is not used as intended.
3 Safety  To prevent injury and damage, read the following safety guidelines prior to operating the device. The manufacturer assumes no liability for any and all damages arising from misuse or noncompliance with these guidelines.  Electrical Hazards  Cleaning/Servicing: Power Off the PM-521  Disconnect the PM-521 from power before cleaning or servicing it.  Power Adapter  Contact an authorized service personnel for repairs to the power pack. In the event of a blown fuse after replacing the fuse, contact an authorized service personnel to avoid electrical shock.  Use only Supplied Power Cables  RuggON power cables meet industrial requirements for low-temperature flexibility, UV resistance, and oil resistance. Use only supplied power cables from RuggON.  If other power cables are used, the following may apply:  The operator is solely responsible for the resulting damage;  All RuggON warranties are void.  Environmental Hazards  Do not use the PM-521 in locations near/with flammable gases or vapor.  The use of electrical equipment in explosive environments can be dangerous.  Turn off the device when near a gas station, fuel depot, chemical plant or a place where blasting operations take place.  Environmental  Ambient Temperature  The PM-521 operates on the basis of a passive cooling concept which internal waste heat is released via the housing surface and requires fresh airflow in the environment.  Operating the PM-521 with no fresh cooling air may cause overheating and damage to the device.  The operating environment should not be enclosed to prevent the cool air being heated by the heat waste from the device.  Connecting and Disconnecting External Devices  To prevent the considerable damage, the PM-521 and the external device should be disconnected from power when connecting/disconnecting excluding USB devices.
4  Only Use Authorized Accessories  Only use the supplied cables, power packs and other accessories that have been tested and approved by RuggON. Contact your local distributor for further information.  Radio Transmissions  Permitted Transmission Power  Follow the national regulations for the maximum permitted transmission power. The operator is solely responsible for this type of operation. Radio Frequency Limited Locations  Considering the radio frequency limitation in hospitals and aircraft, the PM-521 can only be installed with permission.  Industrial computers may affect the function of implanted medical devices such as pacemakers and may cause malfunction.  Cleaning and Servicing  Disconnect the PM-521 from power before cleaning or servicing.  Never clean the PM-521 with compressed air, a pressure washer or a vacuum cleaner.  If necessary, clean the housing of the PM-521 with a damp cloth.  Clean the touch-screen with a nonabrasive cloth.  Regulatory and Certification  FCC  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.  However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
5  Consult the dealer or an experienced radio/ TV technician for help.  Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device is slave equipment; the device is not radar detection and not ad-hoc operation in the DFS band. Labeling Requirements  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  RF Exposure Information (SAR)  This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.  The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the specified power level in different channels.  The highest SAR value for the device as reported to the FCC is 0.55 W/kg when placed next to the body.  CE Marking  This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. Please contact your local representative for ordering information.  This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.  R&TTE  This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.  CB  This device complies with the IEC 60950-1:2005+A1.  Lithium Battery Safety Statement  Lithium battery inside. Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by battery manufacturer.
6
7Introduction    Chapter 1.  Introduction  The PM-521 is a rugged device equipped with 802.11, Bluetooth and GNSS for wireless data communications.  The PM-521 is a rugged 10.1” tablet computer capable of 1920 x 1200 resolution. The PM-521 supports the following operating systems:  Windows®  Embedded 8.1 Industry 64bits  Windows®  Embedded Standard 7 64bits  Windows®  7 Professional 64bits  Windows®  Embedded Standard 8 64bits  Android™ 4.4 (by request)  About This Guide  The PM-521 User Manual provides instruction for qualified personnel to use as a guide for setup of the device. This document is not intended to replace the training and expertise of the end-user.  Unpacking the Device  Before you begin the installation or configuration process make sure to inspect all components and accessories. Contact your representative if there are any missing or damaged items. See “Contacting RuggON” on page 50.  Technical Specifications  Table 1.  Technical Specifications  Item Description Display 10.1-inch LED Backlight, 1920 (W) x 1200 (H) WUXGA Touch screen 10-point capacitive touch screen Brightness 1000 nits CPU Intel Dual Core Atom E3827 1.75 GHz (Bay Trail) Operating System (Optional)  Windows®  Embedded 8.1 Industry 64bits  Windows®  Embedded Standard 7 64bits  Windows®  7 Professional 64bits  Windows®  Embedded Standard 8 64bits  Android™ 4.4 (by request) RAM DDR3L@1333 MHz 4 GB RAM (8 GB by request) Storage mSATA SSD 120 GB (optional: 240 GB) Battery Standard hot swappable battery: 10.8V, 4500mAh, Li-polymer Power Supply AC 100V ~ 240V, 50~60Hz input; 19VDC@3.42A, 65W
8 Introduction     Item Description Dimensions (W x H x L) 280 mm (11”) x 23 mm (0.9”) x 195 mm (7.7”) Weight 1.33 kg (2.93 lbs) Wireless WLAN Wi-Fi IEEE 802.11 a/b/g/n/ac Bluetooth Bluetooth V4.0 Sensor Sensor Gyroscope, G sensor, E-compass, Light sensor I/O Docking Connector 12-pin DC-IN Jack x1 MicroSD Slot x1 Audio Jack x1; headphone / microphone combo USB 3.0 x1; type A USB 2.0 x1; type A RS-232 x1 Micro HDMI x1 Ethernet x1 Security TPM TPM 1.2 BIOS On/Off for I/Os Yes Data Collection Camera  Front: 2.0 Mega-Pixels camera  Rear: 5.0 Mega-Pixels camera with LED auxiliary light and Auto-focus GNSS Yes NFC Optional Barcode Reader Optional
9Introduction    Item Description Rugged Specifications Drop 153 cm (5 feet), 26 drops on plywood MIL-STD 810G  Vibration (MIL-STD-810G Method 514.6 Category 4, Fig 514.6C-1, Fig 514.6C-2, Fig 514.6C-3)  Drop (MIL-STD-810G Method 516.6 Procedure IV)  Mechanical shock (MIL-STD-810G Method 516.6 Procedure I, Procedure V)  Operation and storage temperature (MIL-STD-810G Method 501.5 and 502.5)  Humidity MIL-STD-810G Method 507.5 Humidity Procedure II Aggravated Cycles (Fig 507.5-7) IP rating IP65 Operating Temperature Range -20°C (-4°F) to 50°C (122°F) Storage Temperature Range -30°C (-22°F) to 70°C (158°F) Humidity 5-95% without condensation  PM-521 Configuration Options  The following options are available for the PM-521:  NFC module  Barcode reader
10 Introduction    Parts List  The PM-521 is shipped with the following items. All other accessories are sold and ordered separately. For help, contact your local RuggON sales representative. See “Contacting RuggON” on page 50.                    PM-521          Power Adapter  Stylus  2-Point Carrying Handle           2-Point Shoulder Strap 4-Point Handstrap  Hitch D-rings (Attaching straps)
11Introduction   Identifying the Device  Overview                                Table 2.  Overview  Figure 1.  Overview  No Item Description 1 Left view See “Side View” on page 14 for further information. 2 Front view See “Front View” on page 12 for further information. 3 Rear view See “Rear View” on page 15 for further information. 4 Right view See “Side View” on page 14 for further information. 5 Rubber bumpers Easy to grip rubber bumpers enable the rugged tablet to withstand shocks and drop for use in demanding environments. 6 Bottom view See “Bottom View” on page 13 for further information.
12 Introduction    Front View 1 2      14 fn 13 f1 12 f2  3 4 5 fn   6             11 10    9  8  7   Table 3.  Front View Figure 2.  Front View  No Item Description 1 Front camera 2.0 Mega-Pixels camera. 2 Touch screen 5-point capacitive touch. 3 Barcode trigger If barcode scanner is installed, press to scan. 4 Battery LED Display battery status, see “LED Status” on page 13. 5 Wi-Fi LED The Wi-Fi LED lights to indicate Wi-Fi is enabled. 6 FN LED The FN LED lights when the function switch on. 7 Home key Windows®  8 home key. 8 Volume + Volume increase. 9 Volume - Volume decrease. 10 Power key Turns the PM-521 on or off. 11 Power LED The power LED lights when the device is on. 12 F2 key Programmable function key. 13 F1 key Programmable function key. 14 FN key Programmable function key.
13Introduction   LED Status  Table 4.  LED Status  Item Status Description Green: On Power on Power Off Power off Green: On Fully charged Amber: On Charging Amber: Blinking Low power < 15% Battery Off Not charging / no battery Blue: On FN function switch on FN Blue: Off FN function switch off Blue: On Wi-Fi on Wi-Fi Blue: Off Wi-Fi off Bottom View               Table 5.  Bottom View   1          2 3 Figure 3.  Bottom View  No Item Description 1 Docking connector 12 pin connector for docking onto a station. 2 Kensington lock Lock the PM-521 to a stationary object for security. 3 Pass-through Dual pass-through for WLAN, GNSS
14 Introduction   ON     OFF 3.0   SD 2.0  Side View   Left view   Right view        1  6   2  7 3   8 4  9 10 5 11  13   12  14      Table 6.  Side View Figure 4.  Side Views  No Item Description 1 Left I/O compartment cover Open to access the USB 2.0 port. 2 Micro HDMI Connect HDMI devices to the PM-521. 3 MicroSD slot Insert microSD card in to the slot. 4 Left I/O compartment cover Open to access the left I/O ports. 5 Tether hole Stylus can be tethered to it. 6 USB 2.0 Connect USB devices to the PM-521. 7 Battery switch Switch to ON to provide power from the backup battery. 8 USB 3.0 Connect USB devices to the PM-521. 9 Audio jack Connect a 3.5 mm jack for a headphone or external speakers. 10 Ethernet Connect the PM-521 to an Ethernet (RJ-45) cable. 11 DC-IN jack Insert power connector to charge battery. 12 RS-232 Connect the PM-521 to a serial device. 13 DC-IN cover Open to access the DC-IN jack. 14 Right I/O compartment cover Open to access the right I/O port.
15Introduction   Rear View   1 2  3 4             5 5            Figure 5.  7 6 Rear View  Table 7.  Rear View  No Item Description 1 Battery To install a battery, an external battery is optional. 2 Rear camera 5.0 Mega-Pixels camera with LED auxiliary light. 3 Barcode reader For installing a barcode reader (Optional). 4 NFC sensing area For detecting NFC devices. (Optional) 5 Securing holes Secure the bumpers and the D-rings for the handstrap and shoulder strap. 6 Expansion bay Remove the cover to find the expansion accessory connector. 7 Stylus holder Place stylus here.
16 Introduction   28 / 11    7 7. /  192.3 / 0.9 .5    195 / 7.7  Dimensions  The following image lists the device dimensions without add-ons (mm/inches).    280 / 11         fn  f1 f2  fn           Figure 6.  Front View Dimensions 23 / 0.9                     Figure 7.  Side View Dimensions
17Introduction   Touch Screen Features  Always use the point of the stylus for clicking or making strokes on the touch screen. Never use an actual pen, pencil, or sharp/abrasive object on the touch screen.  The stylus is used as if it were a pen or pencil. Touch the screen with the tip of the stylus then remove the stylus from the screen.  After each use, replace the stylus in the stylus holder for proper care and to preserve the life of the stylus.  Using a stylus is similar to moving the mouse pointer then left-clicking icons on a desktop computer screen.  The following actions are available through the use of the stylus:  Open applications  Choose commands in menu  Select options in dialog box or drop-down menu  Drag the scroll bar  Drag across the text to select content  Place the cursor in a text box before typing  A right click is generated by tapping the mouse icon in the system tray. After tapping, the mouse icon highlights the right button of the icon in red. The next touch screen tap is treated as a right click. The mouse icon returns to the left button highlighted in red so subsequent taps are treated as left clicks.  A stylus replacement kit is available.   To prevent damage or malfunction, always dry the touch screen when wet.
18 Getting Started     Chapter 2.  Getting Started  This section provides an outline of the steps necessary to setup a new PM-521. A detailed guide follows the listed items, see as follows.  For additional technical assistance, contact your RuggON representative. See “Contacting RuggON” on page 50.  It is recommended to installing or remove accessories on a clean, well-lit work surface. To protect yourself and the device from electrostatic discharge, wear anti- static wrist straps or place the device on an anti-static mat.  First Time Use  1.  Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Switch the switch to the ON position.              Figure 8.  Switching the Battery Switch  3.  Close the left I/O compartment cover. See “Closing the I/O Compartment Cover” on page 26.  Charging the Battery  When you use the AC adapter to connect your PM-521 to a power outlet, the standard and external (optional) battery will automatically begin to recharge.  While the battery is charging, the power LED will be active. When the battery is fully charged, the power LED is lit a solid green.  1.  Flip open the DC-IN cover to expose the DC-IN jack.               Figure 9.  Opening the DC-IN Cover
19Getting Started   2.  Connect the AC adapter to the DC-IN port.             Figure 10.  Connecting the AC Adapter  After charging the battery, disconnect the AC adapter and close the DC-IN cover.  1.  Insert one end of the cover first and angle the cover to seat it in place.  2.  Push in the cover to seal the DC-IN compartment.                Figure 11.  Closing the DC-IN Cover   The DC-IN cover must be inserted correctly to prevent internal damage to the device.   Powering the Device On and Off  Powering On the Device  Only power on the PM-521 after connecting all of the peripherals and cabling.  1.  Press and hold the power button until the screen lights. The device runs through the start up sequence and powers up.                Figure 12.  Power On the PM-521
20 Getting Started   ON      OFF3.0 2.0  SD  Powering Off the Device  Start screen:  Tap > Shut down.  Desktop screen:  1. Tap and hold  at the bottom left corner of the Desktop screen.  2. Tap Shut down or sign out > Shut down.   Bot h Start screen and Desktop screen: 1. Display charm bar and tap Settings.2. Tap Power > Shut down.  Installing the MicroSD Card  The device supports microSD card for easier data storage.  1.  Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Locate the microSD slot in the left I/O parts. Left view          MicroSD Slot         Figure 17.  Left View: Locating the MicroSD Slot
21Getting Started  ON      OFF 3.02.0  SD  3.  The microSD card has a beveled edge. Align the microSD card with the slot making sure that the corners match.  4.  Insert the microSD card and press it in until an audible click sounds.               Figure 18.  Installing the MicroSD Card  5.  Close the left I/O compartment cover. See “Closing the I/O Compartment Cover” on page 26.  Removing the MicroSD Card  1.  Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Locate the microSD slot in the left I/O parts. Left view          MicroSD Slot         Figure 19.  Left View: Locating the MicroSD Slot
22 Getting Started    3.  Press the microSD card in and release it. The card springs out.  4.  Grasp the microSD card and remove it from the slot.                Figure 20.  Removing the MicroSD Card  5.  Close the left I/O compartment cover. See “Closing the I/O Compartment Cover” on page 26.  Using the Stylus  Following the information below when using a stylus:  Use only the included stylus to touch the screen. Do not place any objects on its surface and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens).  Use the stylus only for touching the screen. Using it for any other purpose may damage the stylus and result in scratches on the screen.  The pointer cannot follow the stylus movement if you move the stylus too quickly.  To make a selection, tap the screen once with the stylus. To double-click, tap twice without pausing. To do a right-click, tap the screen once and hold the tip of the stylus on the screen, the right-click icon appears.  Removing the Protective Film from the Display  The front display of the PM-521 is protected during transport by a transparent film. This film should remain on the front display during assembly to avoid damage to the front display surface.  Only remove the film once all of the assembly work has been completed.    fn f1 f2  fn         Figure 21.  Removing the Protective Film
23Operation  ON      OFF3.0  SD 2.0   Chapter 3.  Operation   Opening the I/O Compartment Cover  1.  Place the device display side down on a clean work surface.  2.  Locate the I/O compartment cover. Left view           Right view     Left I/O Compartment Cover  Left I/O Compartment Cover   Right I/O Compartment Cover    Figure 22.  Side View: Locating the I/O Compartment Cover  3.  Unlock the latch. (Only available for the left I/O compartment cover)                Figure 23.  Unlocking the Latch  4.  Pull out the I/O compartment cover.                Figure 24.  Openin the I/O Compartment Cover
24 Operation   ON      OFF 3.0  SD 2.0  Closing the I/O Compartment Cover  1.  Place the device display side down on a clean work surface.  2.  Locate the I/O compartment cover. Left view       Right view     Left I/O Compartment Cover  Left I/O Compartment Cover   Right I/O Compartment Cover    Figure 25.  Side View: Locating the I/O Compartment Cover  3.  Flip the I/O compartment cover and install.                Figure 26.  Installing the I/O Compartment Cover  4.  Lock the latch. (Only available for the left I/O compartment cover)                Figure 27.  Locking the Latch   The I/O compartment cover must be inserted correctly to prevent internal damage to the device.
25Operation   Connecting to External Cabling   To prevent damage to the device, connect all cabling and accessories before powering up the device.  Connect USB Cabling  The PM-521 have one USB 3.0 and one USB 2.0 ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. The USB ports support USB 2.0 or USB 3.0 devices.  1.  Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Connect to USB device via USB cable.            Figure 28.  Connect USB 2.0 Cabling
26 Operation          Figure 29.  Connect USB 3.0 Cabling
27Operation   Connect Ethernet Cabling  The PM-521 provide have a Ethernet port for connecting Ethernet.   Use a shielded cable is required to maintain emissions and susceptibility compliance.   1.  Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Connect LAN cable to Ethernet port on the PM-521.                Connect Audio Cabling Figure 30.  Connect Ethernet cabling  For higher audio quality, you can send sound through external audio devices such as speakers, headphones, or earphone using audio connector.  1.  Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Connect the audio cable.               Figure 31.  Connect Audio Cabling
28 Operation    Connect Micro HDMI Cabling  Connect to HDMI devices via micro HDMI cable.  1.  Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Connect micro HDMI cable to micro HDMI port on the PM-521.                        Connect RS-232 Cabling Figure 32.  Connect Micro HDMI Cabling  Connect to RS-232 devices via RS-232 cable.  1.  Open the right I/O compartment cover. See “Opening the I/O Compartment Cover” on page 25.  2.  Align the RS-232 cable with the port in the device and connect it.  3.  Turn the locking screws on the cable to secure it to the device.              Figure 33.  Connect RS-232 Cabling
29Operation   Handstrap, Carrying Handle and Shoulder Strap  The PM-521 is equipped with a handstrap, a carrying handle and a shoulder strap for convenience and choice. Select the accessory that is right for your needs.  The handstrap can be installed with either the shoulder strap or the carrying handle. However, the handle and shoulder strap can not be installed together due to space constraints.  For more information, see “Connecting the Handstrap” on page 30, “Connecting the Carrying Handle” on page 32 and “Connecting the Carrying Handle” on page 32.  Connecting the Handstrap  1.  Remove the screws securing the bumpers.                  2.  Install the D-rings. Figure 34.  Removing the Screws   Make sure the D-rings are tightly secured before installing the handstrap.                 Figure 35.  Installing the D-rings
30 Operation    3.  Connect the handstrap on the D-rings.   When the handstrap is installed, the stylus can be placed under the strap.                         Removing the Handstrap Figure 36.  Connecting the Handstrap  1.  Unlock the handstrap from the D-rings.                        2.  Remove the D-rings. Figure 37.  Removing the Handstrap                Figure 38.  Removing the D-rings
31Operation   3.  Secure the bumper and the PM-521 with screws.                Figure 39.  Securing the Screws  Connecting the Carrying Handle  1.  Attach the clips to the metal loop on the bumper.                Figure 40.  Connecting the Carrying Handle  Removing the Carrying Handle  1.  Press in the clips to release them from the metal loop.  2.  Remove the clips.                Figure 41.  Removing the Carrying Handle
32 Operation    Connecting the Shoulder Strap  1.  Attach the clips to the metal loop on the bumper.                      Figure 42.  Connecting the Shoulder Strap  Removing the Shoulder Strap  1.  Press in the clips to release them from the metal loop.  2.  Remove the clips.                      Figure 43.  Removing the Shoulder Strap
33Operation   Installing the Standard Battery  The following instructions are for both standard and external batteries. The external battery is an optional component. Only use components specifically designed for this device. Contact your local representative for ordering information.  Make sure the power switch is switched to ON before installing the standard/external battery. See “First Time Use” on page 18.  1.  Place the device display side down on a clean work surface.  2.  Locate the battery.   Locking Switch Release Button     Battery       Figure 44.  Rear View: Locating the Battery  3.  Align the tabs on the battery with the slots on the chassis.  4.  Angle the battery in place and set the tabs in the chassis slots.  5.  Lower the raised end of the battery and press in place until an audible click is heard.               Figure 45.  Installing the Battery
34 Operation    6.  Slide the locking switch on the top-left side to lock the battery.               Figure 46.  Locking the Battery   Make sure the latch is securely locked to prevent the battery from falling.   Removing the Standard Battery  1.  Place the device display side down on a clean work surface.  2.  Locate the battery.   Locking Switch Release Button     Battery       Figure 47.  Rear View: Locating the Battery  3.  Slide the locking switch on the top-left side to the unlock position.               Figure 48.  Unlock the Battery  4.  Press and hold the release button as shown in the image to release the battery.
35Operation   5.  Hold the battery and angle the left side up to remove.               Figure 49.  Removing the Battery   Connecting to a Wireless Network  Before you can make use of the PM-521 wireless functions, you need to connect to a network. The following is a set of procedures for connecting to a wireless network.  1.  Before beginning, make sure your Wi-Fi setting is enabled and you are within range of a wireless network. If your Wi-Fi setting is disabled, proceed to step 2.  Look at the Network icon located at the right side of the taskbar. If the icon displays an X in a red circle, you are not within range of a wireless network. Move to a different spot until the Wi-Fi icon changes status indicating availability to a wireless network.  2.  From any screen, open the Charms bar by sliding your finger inward from the screen’s right edge. The Charms bar displays along the screen’s right side.  3.  In the Charms bar, tap Settings to open the Settings menu.  4. In Settings, tap the Network icon to display the Networks connection settings.  5.  The Wi-Fi menu displays. By default, the Wi-Fi menu is set to Off. Tap the bar next to Off to toggle Wi-Fi to On. This enables the Wi-Fi option.  6.  Once W-Fi is enabled a listing of all available wireless networks displays. The wireless networks with the strongest signal are atop the list.  7.  Select the network you want to connect to, and tap the Connect button. You can tap the Connect Automatically check box if you connect to this network frequently. If you connect to the network, you are finished with the process. The network is considered an Open unsecured network, no passoword is required.  8.  If a password is required, type the password in the Enter the network security key field. Alternatively, you can also push the WPS button on your router to begin the security handshake.  9. Tap Next to finish the connection process.  You have successfully connected to a wireless network.
36 Using BIOS Setup Utility     Chapter 4.  Using BIOS Setup Utility  Your ruggedized tablet has a BIOS setup utility which allows you to configure important system settings, including settings for the Boot and AP menus as well as the device’s basic settings--the system reads the basic settings during initialization in order to boot correctly  When to Use the BIOS Setup Utility  You need to run the BIOS Setup utility when:  Restoring to BIOS settings to factory default  Modifying specific hardware settings  Modifying specific settings to optimize system performance  Installing Windows 7 operating system  Accessing the BIOS Setup Utility  The BIOS Setup Utility screens shown in this chapter are for your reference only. The actual images or settings on your tablet computer may differ. The BIOS Setup Utility program may have been updated after the publication of this manual. To run the BIOS Setup Utility, use the following procedures:  1.  Perform one of the following:  If the PM-521 is powered off Press the Power button to start up the device. The power LED lights. Quickly press and hold the Windows Home key until the BIOS Post screen displays.  If the PM-521 is powered on Press the Power button to shut down the device. Quickly press and hold the Windows Home Key until the BIOS Post screen displays. The BIOS POST screen appears as shown. 2.  From the BIOS POST screen select App Menu to open the BIOS Setup Utility.  Figure 50.  BIOS POST Screen
37Using BIOS Setup Utility   Due to the device’s fast boot up and boot down time, there is only a small time frame of a few seconds between the release of the Power button and the opportunity to press the Windows Home key.  The App Menu displays.  Figure 51.  BIOS Setup Utility: App Menu Screen   Installation an Operating System  Setting Up a Windows 7 Installation Environment  There are several settings in BIOS that must be modified before you can install a Windows 7 operating system.  Use the following guidelines to prepare the BIOS environment:   Ste p 1: Enable CSM Support 1. Access the BIOS Setup Utility, see “Accessing the BIOS Setup Utility” on page 37. 2. Navigate to APP Menu > Main > Boot Features. 3. Locate the CSM Support setting and tap the drop-down menu to display the options.
38 Using BIOS Setup Utility    4. Tap Yes to enable CSM support.     Step 2 Enable Legacy Boot Figure 52.  Main > Boot Features  1.  Access the BIOS Setup Utility, see “Accessing the BIOS Setup Utility” on page 37.  2. Navigate to APP Menu > Main > Boot Features.  3. Locate the Legacy Boot setting and tap on the menu to select On enable legacy boot.   Figure 53.  Main > Boot Features   Ste p 3: Enable USB 2.0 Support 1. Access the BIOS Setup Utility, see “Accessing the BIOS Setup Utility” on page 37.2. Navigate to APP Menu > Advanced > Miscellaneous Configuration. 3. Locate the USB Controller Select drop-down menu and tap on it.
39Using BIOS Setup Utility   4. Tap USB 2.0 from the menu list. USB 2.0 is now enabled for the device.   Figure 54.  Advanced > Miscellaneous Configuration  Step 4: Advanced > Miscellaneous Configuration  Save the Settings  After you configure BIOS, you will need to save the settings.  1. Navigate to APP Menu > Exit and tap Exit Saving Changes.   Figure 55.  Exit the BIOS Utility  2. A prompt display, tap Yes to save the configuration.  The BIOS settings are configured and the Windows 7 operating system can be installed.
40 Using BIOS Setup Utility    BIOS Passwords  Setting Up a Supervisor Password  To setup a supervisor password, follow the procedure as described:  1. Go to APP Menu > Security > Account’s Password Status.  2. Tap the Enter icon next to Setup the Supervisor Password to access the virtual keyboard.   Figure 56.  Security > Account’s Password Status  3.  Tap the password to use for the Supervisor profile and tap Enter.   Figure 57.  Set Supervisor Password
41Using BIOS Setup Utility   4.  Verification of the password is required. Tap the same password again and tap Enter to confirm the new password.  5. Navigate to APP Menu > Exit.   Figure 58.  Exit Screen  6. Tap Exit Saving Changes to display the confirmation screen.  7. Tap Yes to save the new configuration settings.  After setting the Supervisor password, the password is required to access the BIOS Setup Utility.  Changing a Supervisor Password  1. Navigate to APP Menu > Security > Account’s Password Status.  2. Tap the Enter icon next to Setup Supervisor Password.  3.  Enter the current supervisor password.  4.  Enter a new password.  5.  Enter the new password again to confirm.  6. Go to APP Menu > Exit.  7. Tap Exit Saving Changes and tap Yes to save the configuration.  Resetting a Supervisor Password  A supervisor password can not be reset. In the event that you forget the supervisory password, you will need to reflash the BIOS to enter the BIOS menus. Refer to “Updating BIOS” on page 43 to reflash the BIOS.
42 Using BIOS Setup Utility    EC and BIOS  Updating BIOS  This procedure allows you to update and reflash the system BIOS. Both procedures follow the same steps as described in the following.  Make sure to protect your device from power loss during the BIOS update procedure to prevent irreparable damage to your system’s mainboard.  For this procedure, it is highly recommended to connect the device to the AC adapter to prevent a sudden loss of power during the BIOS updating process.  1.  Contact your technical sales or technical representative to obtain the correct BIOS file.  2.  Copy the BIOS file on to the USB device.  3.  Connect the USB device to one of the device’s USB ports and power on the PM-521.   A USB keyboard is required for entering command.   4.  Once the device is on and the Windows 8 Home screen displays, open the Charms bar by sliding your finger inward from the screen’s right edge. The Charms bar displays.  5. Tap Settings from the displayed menus.                          Figure 59.  Charms Bar > Settings
43Using BIOS Setup Utility   6. Tap Change PC settings.                          Figure 60.  Change PC Settings  7.  From the PC settings menu, tap Update and recovery to continue.                          Figure 61.  Update and Recovery
44 Using BIOS Setup Utility    8. From the Update and recovery screen, tap Recovery. The Advanced startup option displays.                          Figure 62.  Recovery  9. Under Advanced startup, tap Restart now.                          Figure 63.  Restart Now
45Using BIOS Setup Utility                           Figure 64.  Use a Device  11.  From the Use a device menu, tap Internal Shell to open the command screen.   Make sure connect the PM-521 to the AC adapter to prevent a sudden loss of power.                           Figure 65.  Internal Shell
46 Using BIOS Setup Utility 10.  Tap Use a device to select a boot up preference.   12.  In the command screen, enter fs1: to select the USB device already connected to the device. The command directs you to the USB device’s root menu.   Figure 66.  Internal Shell Command Screen  13.  If the BIOS file is in a folder and not in the root directory, navigate to the target folder.  14.  Type wf (.nsh) and tap Enter. wf is the designated BIOS file. Do not turn off your device or interfere with the reflash process until the process is complete.  15.  Reboot the PM-521. The BIOS is now updated. Updating EC   Connect the PM-521 to the AC adapter to prevent a sudden loss of power.   1.  Updating EC requires the use of the Internal Shell Command menu, refer to steps 1 to 12 of “Updating BIOS”.  2.  Enter the EC source file folder.  3.  In the source folder, enter f.  4.  Do not turn off your device or interfere with the reflash process until the process is complete.  The system reboots once the process is completed.
47Using BIOS Setup Utility  Chapter 5.  Troubleshooting  Use the troubleshooting tables in this section to fix problems with the Wi-Fi connection, 802.1x security, or general problems with operating the computer.  If you send the computer in for service, it is your responsibility to save the computer data and configuration. RuggON is responsible only for ensuring that the hardware matches the original configuration when repairing or replacing the computer.  Troubleshoot the Wi-Fi Connection  Use this troubleshooting table to help solve problems with your 802.11 radio connection.  Q.  When you turn on the computer after it was suspended for a while (10 to 15 minutes or longer), it can no longer send or receive messages over the network. A.  Host may have deactivated or lost current terminal emulation session. In a TCP/IP direct connect network, turn off the “Keep Alive” message from host to maintain the TCP session while the computer is suspended.  Q.  The computer is connected to the network and you move to a new site to collect data. Your computer now shows you are not connected to the network. A.  Move closer to an access point or to a different location to reestablish communications until you reconnect with the network.  Q.  The computer appears to be connected to the network, but you cannot establish a terminal emulation session with the host computer. A.  There may be a problem with the host computer, or with the connection between the access point and the host computer. Check with the network administrator to make sure the host is running and allowing users to log in to the system.  Q.  The computer appears to be connected to the network, but the host computer is not receiving any information from the computer. A.  There may be a problem with the connection between the access point and the host computer. Check with the network administrator or use your access point user’s manual.  Q.  A network connection icon appears in the toolbar, but then disappears. A.  The computer may not be communicating with the intended access point. Make sure the network name matches the access point network name. The access point may not be communicating with the server. Ensure the access point is turned on, properly configured, and has 802.1x security enabled.
48 Troubleshooting      Troubleshoot Operating the Computer Troubleshooting  Use this section to troubleshoot problems that may prevent you from being able to operate the computer. Q.  You press the Power button and nothing happens. A.  Make sure that power is connected to the computer.  Q.  The computer appears to be locked and you cannot enter data. A.  Restart the computer.   Call Product Support  Simple instructions please contact the dealer, contact ruggon representative, or leave a message visit the RuggON website at www.ruggon.com.  To better assist you have the following information ready:  Configuration number  Serial number  Operating system, BIOS, and MCU versions  Service pack version  System component versions  If you are using security, know the type and the full set of parameters
Maintenance 50   Chapter 6.  Maintenance   Cleaning the Device  Danger to electric shock when cleaning or maintaining the PM-521. To avoid electric shock, turn the PM-521 off and disconnect it from the power supply before cleaning or maintaining it. Housing  The housing of the PM-521 is best cleaned with a damp cloth.  Use compressed air, a high-pressure cleaner or vacuum cleaner may damage the surface.  Use a high-pressure cleaner, the additional risk of water entering the PM-521 may damage the electronics or touch screen.  Touch Screen  Use neutral detergent or isopropyl alcohol on a clean soft cloth to clean the panel surface.  Prevent using any kind of chemical solvent, acidic or alkali solution.  Returning the Device  Please put the contents in the original package gently when you need to return the PM-521.  Contacting RuggON  If you experience technical difficulties, please consult your distributor or contact the technical services department:  www.ruggon.com
                    PAC

Navigation menu