RuggON PM311B TABLET PC User Manual Part 2

RuggON Corporation TABLET PC Part 2

User manual_Part 2

33Operation2. Align the holes on the bottom of the cover with the pins on the top of the housing and insert.3. Place the device display side down on a clean work surface.Figure 38. Installing the Snap-on Module Connector Cover4. Secure the cover and the PM-311B with screws.Figure 39. Securing the ScrewsSnap-on module connector cover is not be closed well may damage the PM-311B.
34OperationOpening the I/O Compartment Cover1. Place the device display side down on a clean work surface.2. Locate the I/O compartment cover.Right viewLeft viewLeft I/O Compartment CoverRight I/O Compartment CoverFigure 40. Side View: Locating the I/O Compartment Cover3. Pull out the I/O compartment cover.Figure 41. Opening the I/O Compartment Cover
35OperationClosing the I/O Compartment Cover1. Place the device display side down on a clean work surface.2. Locate the I/O compartment cover.Right viewLeft viewLeft I/O Compartment CoverRight I/O Compartment CoverFigure 42. Side View: Locating the I/O Compartment Cover3. Flip the I/O compartment cover and install.Figure 43. Closing the I/O Compartment CoverThe I/O compartment cover must be inserted correctly to prevent internal damage to the device.
36OperationConnecting to External CablingTo prevent damage to the device, connect all cabling and accessories before powering up the device.Connect USB CablingThe PM-311B have two USB ports for connecting USB devices, such as a digital camera, scanner, printer, modem, and mouse. The USB port support USB 2.0 or USB 3.0 devices.1. Open the left or right I/O compartment cover. See “Opening the I/O Compartment Cover” on page 34.2. Connect to USB device via USB cable.Figure 44. Connect USB CablingConnect Ethernet CablingThe PM-311B provide have a Ethernet port for connecting Ethernet.Use a shielded cable is required to maintain emissions and susceptibility compliance.1. Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 34.2. Connect LAN cable to Ethernet port on the PM-311B.Figure 45. Connect Ethernet Cabling
37OperationConnect Audio CablingFor higher audio quality, you can send sound through external audio devices such as speakers, headphones, or earphone using audio connector.1. Open the right I/O compartment cover. See “Opening the I/O Compartment Cover” on page 34.2. Connect the audio cable.Figure 46. Connect Audio CablingConnect RS-232 CablingConnect to RS-232 devices with an RS-232 cable.1. Open the left I/O compartment cover. See “Opening the I/O Compartment Cover” on page 34.2. Align the RS-232 cable with the port in the device and connect it.3. Turn the locking screws on the cable to secure it to the device.Figure 47. Connect RS-232 Cabling
38OperationHandstrap, Carrying Handle and Shoulder StrapThe PM-311B is equipped with a handstrap, a carrying handle and a shoulder strap for convenience and choice. Select the accessory that is right for your needs.The handstrap can be installed with either the shoulder strap or the carrying handle. However, the handle and shoulder strap can not be installed together due to space constraints.For more information, see “Connecting the Handstrap” on page 38, “Connecting the Carrying Handle” on page 39 and “Connecting the Shoulder Strap” on page 41.Connecting the HandstrapThe handstrap makes it easy to carry the device with a single hand.When attached, the handstrap blocks access to the external battery and connector. To install the external battery, you will need to remove the handstrap if it is previously installed.1. Position the handstrap so that the inner strap is facing the device.2. Place the D-rings over the upper and lower positions on the device.3. Twist the D-rings (clockwise) to secure the handstrap.Figure 48. Securing the Handstrap
39OperationRemoving the Handstrap1. Unscrew the D-rings securing the handstrap to the device.2. Remove the handstrap from the PM-311B.Figure 49. Removing the HandstrapConnecting the Carrying Handle1. The handle must face the correct way. The securing post and velcro should be facing outward.2. Thread one end of the strap through the metal loop on the bumper.StrapMetal LoopPostVelcroFigure 50. Inserting the Carrying Handle Through the Loop
40Operation3. Pull the strap end through the loop and insert the post through the slit on the strap.4. Secure the strap by attaching the two velcro ends together.Figure 51. Securing the Strap5. Repeat fro the remaining strap end.Removing the Carrying Handle1. Remove the strap from the velcro and securing post.Figure 52. Removing the Strap2. Pull the strap through the metal loop on the bumper.Figure 53. Removing the Carrying Handle3. Repeat fro the remaining strap end.4. Remove the carrying handle.
41OperationConnecting the Shoulder Strap1. The shoulder strap must face the correct way. The securing post and velcro should be facing outward.2. Thread one end of the strap through the metal loop on the bumper.VelcroMetal LoopPostVelcroFigure 54. Inserting the Shoulder Strap Through the Loop3. Pull the strap end through the loop and insert the post through the slit on the strap.4. Secure the strap by attaching the two velcro ends together.Figure 55. Securing the Strap5. Repeat for the remaining strap end.
42OperationRemoving the Shoulder Strap1. Remove the strap from the velcro and securing post.Figure 56. Removing the Strap2. Pull the strap through the metal loop on the bumper.Figure 57. Removing the Shoulder Strap3. Repeat for the remaining strap end.4. Remove the shoulder strap.
43OperationInstalling the External BatteryThe external battery is an optional component. Only use components specically designed for this device. Contact your local representative for ordering information.1. Place the device display side down on a clean work surface.2. Locate the external battery connector cover.External Battery Connector CoverFigure 58. Rear View: Locating the External Battery Connector Cover3. Flip the connector cover up to remove it from the compartment.Figure 59. Removing the External Battery Connector Cover
44Operation4. Align the tabs on the external battery bracket with the slots on the rear side of the PM-311B .Figure 60. Aligning the External Battery Bracket5. Push the external battery bracket toward to lock.Figure 61. Installing the External Battery Bracket6. Securing the external battery bracket and the PM-311B with screws.Figure 62. Securing the Screws
45Operation7. Install the connector cover in the cover placeholder.Figure 63. Placing the External Battery Connector Cover in the Cover Placeholder8. Align the tabs on the external battery with the slots on the external battery bracket.9. Angle the battery in place and set the tabs in the bracket slots.10. Lower the raised end of the external battery and press in place until an audible click is heard.Figure 64. Installing the External Battery11. Press the locking switch on the top-left side to lock the external battery.Figure 65. Locking the External Battery

Navigation menu