Rui dasheng technology CDRZ32 Wireless Charger User Manual

Rui dasheng technology(shenzhen) Co. Ltd. Wireless Charger

User manual

Please read this Operation Instruction carefully and keep it properly before using this product. 1. Do not press hard or crash the product.2. Do not disassemble or reassemble.3. Do not put the product near the fire or into the fire, water.4. Do not use wireless charger in severe high temperature and humidity or corrosion to avoid leakage.5. Do not place too close to a magnetic card(id card and credit card)with a magnetic strip or chip to avoid the failure of the magnetism.6. Do not put metal plate or metal shell on the charger.7. Please keep the distance between the implanted medical device (pacemakers, implants, etc.) and the wireless charger at least 20cm to avoid potential interference to the medical device.8. Please keep the charger away from water or other liquids.9. Make sure not connect the power if you need to clean the wireless charger.10. Please don't use it as a toy for children.11. The ambient temperature shall be kept between 0-45℃.In order to bring you a better experience, read this manual and also please refer to your mobile phone or electronic product manual.Thank you for purchasing and using this product!Internal magnetic inductioncoil of Wireless chargerInternal magnetic induction coil of cellphoneProduct overview Instructions NotesPhoneWireless charger (4 - 6)mmProduct specificationsCharging induction distance: the distance between the innerinduction coil of the handset and the inner inductance coil of the wireless charger is (4-6) mm, and the mobile phone avoids using a thicker mobile phone shell when using.Type-C input portIndicator lightSensor zone1. When the wireless charger is power-on, the blue light will flash for 2 seconds and go out; the charger goes into standby;2. Put mobile phone in the induction zone; blue light will stay on to indicate the phone is charging;3. When the wireless charger senses metal objects other than mobile phones, blue light will keep flashing and the charger will turn on charging protection.Note: the charging equipment must meet the Qi standard to be used.Wireless chargerCDRZ32Diameter≈99mm, Thickness≈13mm5V 2A, 9V 2A, 12V 1.5A15W(Max)(4~6)mm≈138gThe Qi standard of iPhone, Samsung,LG, Moto and other whole series will support the wireless charging modelsWireless charger ×1, Type-C data line ×1, Instruction book ×1Product nameModelSizeInput PowerCharging inductiondistanceNet weightApplicable model Product list Warranty CardCustomer Name:Phone Number:Product Name:Date of Purchase:Address:Notes:The parameters above are derived from the laboratoryof ANDOBIL, The actual parameter would be different because of products or other factors. The image shown here is indicative only.C2WIRELESS CHARGERWWW.ANDOBIL.COMEmail: zhumiben@lanhe-tech.comAdd: 23B03, Haerbing building, 7045# Beihuan road, Kangxin community, Lianhua street, Futian district, Shenzhen, Guangdong, China Rui dasheng technology(shenzhen) Co. Ltd. Andobil is the trademark registered in U.S and other countries. All rights reserved.MADE IN CHINAFCC StatementThis device complies with part 15 and part 18 of the FCC Rules. Operation is Subject To the following two conditions:(1) This device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the partyresponsible for compliance could void the user's authority tooperate this equipment.Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and part 18 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:.• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:●Increase the separation between the equipment and any other radio device.●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Navigation menu