Runcom Communications BTSTVWS-1 Base Station User Manual
Runcom Technologies Ltd. Base Station
Contents
- 1. User Manual
- 2. Revised Brochure
- 3. User Operational Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2678919 |
| Application ID | BhKmDOcDgsHCfaV3H+RF3g== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 440.47kB (5505916 bits) |
| Date Submitted | 2015-07-14 00:00:00 |
| Date Available | 2015-09-11 00:00:00 |
| Creation Date | 2015-07-06 13:40:00 |
| Producing Software | GPL Ghostscript 9.06 |
| Document Lastmod | 2015-07-06 13:40:00 |
| Document Title | Microsoft Word - Runcom RNU4000BS User Manual -RN-PMG-020615 V-4.1.docx |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | Tzvim |
RNU4000BS User Manual Table of Contents , our product manager WiMAX RNU4000BS Base Station User Manual Doc: RUNCOM RNU4000BS USER MANUAL –RN–PMG-020615 V-4.1 Runcom Technologies Ltd. Table of Contents RNU4000BS User Manual About this Guide This User Manual describes the procedures for commissioning, mounting, installing and managing the RNU4000BS Base Station. This base station comprises several base station types related to the frequency band. The base station is configured at the factory. For TVWS, this base is identified as RNU4000-TVWS. RNU4000-TVWS is designed to meet FCC Part 15 subpart H fixed device requirements. Notice This document contains proprietary and confidential material of Runcom Ltd. Any unauthorized reproduction, use or disclosure of this material, or any part thereof, is strictly prohibited. This document is solely for the use of Runcom Ltd. employees and authorized Runcom Ltd. customers. The material furnished in this document is believed to be accurate and reliable. However, no responsibility is assumed by Runcom Ltd. for the use of this material. Runcom Ltd. reserves the right to make changes to the material at any time and without notice. All other trademarks are the property of their respective owners. Other company and brand products and service names are trademarks or registered trademarks of their respective holders. Safety Precautions To avoid injury and to prevent equipment damage, observe the safety precautions below. • • • • • • • • • • Only qualified personnel should be allowed to install, replace, and service the equipment. The device cannot be sold retail, to the general public or by mail order. It must be sold to dealers. Installation must be controlled. Installation must be performed by licensed professionals. Installation requires special training. The Runcom radios and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void product warranty and may expose the end user or the service provider to legal and financial liabilities. Always observe standard safety precautions during installation, operation and maintenance of this product. This equipment must be installed according to country national electrical codes. Any changes and modifications to the device and the accessories must be approved by Runcom. All equipment and accessories must be installed in a restricted access area. Observe all the labels on the equipment, providing operation details and warnings. Read and follow the installation instructions provided in this manual. The outdoor base station should be positioned more than 2 meters from humans. In case of using cables that are not provided with the equipment package, ensure these cables comply with the regulatory inspection authorities and are the responsibility of the customer. Do not move or ship equipment unless it is properly packed in its original wrapping and shipping containers. Electrical Shock Prevention • When connecting equipment to the AC and DC voltage supplies, ensure proper polarity. RNU4000BS Base Station User Manual • • • • • • שגיאה! השתמש בכרטיסיה בית כדי להחילHeading 1.על הטקסט שברצונך שיופיע כאן Disconnect the power source before installing or maintaining the power wiring. Do not operate the equipment if there is any failure or damage to electrical components. Do not touch exposed connections, components or wiring when power is on. Install the equipment and the grounded DC supply circuits in adjacent cabinets. Protect the DC power source with an adjacent circuit breaker. The equipment must be properly grounded before attempting to operate or perform any repairs. RF Exposure To comply with FCC Section 1.310 for human exposure to radio frequency electromagnetic fields, implement the following instruction: A distance of at least 200cm between the equipment and all persons should be maintained during the operation of the equipment. Radio Interference This equipment generates and radiates radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. To avoid interferences: • • • NOTE: Avoid conjunction with any other antenna or transmitter. In case of Radio Interference: Relocate the antenna and Increase separation between the equipment and the receiver (e.g. connect to a separate circuit or outlet). When using an external antenna, the external antenna must not be co-located or operating in conjunction with any other antenna or transmitter This equipment has been tested and found to comply with the rules for TV bands devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Note: Contention Based Protocol (CBP) MUST be activated for the specified band (3.675-3.700GHz) wherever FCC rules and regulations are enforced. Failure to comply makes the operation of this device illegal. Table of Contents RNU4000BS User Manual NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. Warning: THE BTSTVWS-1 EQUIPMENT SHALL BE INSTALLED AT A HEIGHT NO GREATER THAN 30 METERS ABOVE THE GROUND. RNU4000BS TVWS Operation RNU4000-TVWS is RNU4000BS unit set at the factory to operate and meet FCC requirements for unlicensed TVWS operation. For interference avoidance the RNU4000-TVWS connects with a TVWS database using its related Automated Frequency Allocation Server (AFAS). AFAS is described in its manual named - AFAS Operation Manual. RNU4000-TVWS Regulatory Compliance Information This equipment has been tested and found to comply with the rules for TV band devices, pursuant to Part 15 of the FCC Rules. FCC Registration Requirements: Per FCC regulations; RNU4000-TVWS base station registration with Spectrum Bridge database is required prior to performing any tests and/or completing installation. Declaration of Conformity Manufacturer’s Name: Runcom Manufacturer’s Address: Hachoma 2 Rishon Letzion Israel Declares that the product: RNU4000-TVWS base station conforms to the FCC Part 15 subpart H regulations. RNU4000BS Base Station User Manual שגיאה! השתמש בכרטיסיה בית כדי להחילHeading 1.על הטקסט שברצונך שיופיע כאן Table of Contents Introducing the RNU4000BS BS ....................................................................................... 1 1.1 Coverage Configurations ..............................................................................................................3 1.2 RNU4000BS Interfaces and Accessories .........................................................................................5 1.2.1 GPS, Power and Communication Interfaces ..........................................................................5 1.2.2 BS RF Antenna Interfaces ...................................................................................................7 1.3 Supported Antennas .....................................................................................................................7 1.3.1 RF Antennas ......................................................................................................................7 1.3.1.1 Internal Antennas ...................................................................................................7 1.3.1.2 External Antenna ....................................................................................................7 1.4 Optional Accessories ....................................................................................................................8 WEB GUI description ........................................................................................................ 9 2.1 WEB GUI Menu description ......................................................................................................... 10 2.2 WEB GUI working screens description ......................................................................................... 10 Commissioning Procedure ............................................................................................. 24 3.1 Overview ................................................................................................................................... 24 3.2 Connect BS to Power and Computer ............................................................................................ 25 3.2.1 Configure the Computer's Network Parameters .................................................................. 25 3.2.1.1 Configure Computer IP Address............................................................................. 25 3.2.1.2 Disable Firewall .................................................................................................... 28 Table of Contents RNU4000BS User Manual Installing the RNU4000BS BS.......................................................................................... 29 4.1 Mounting the Base Station .......................................................................................................... 29 4.1.1 BS Installation Location ..................................................................................................... 29 4.1.2 Mounting Bracket Description ............................................................................................ 30 4.1.3 Mounting On a Pole .......................................................................................................... 32 4.1.4 Mounting On a Wall .......................................................................................................... 34 4.2 Overview of the Cable and Power Connections............................................................................. 36 4.3 Mounting the RF Antennas.......................................................................................................... 38 4.3.1 Mounting the RF Antenna.................................................................................................. 38 4.3.1.1 4.3.1.2 4.3.1.3 4.4 Pole Mounted RF Antenna Location Criteria ................................................................................. 38 RF Antenna Mounting ........................................................................................... 38 4x4 antennas Outdoor Connection Requirements ................................................... 39 GPS Antenna ........................................................................................................ 40 4.4.1 GPS Antenna Installation ................................................................................................... 41 4.4.2 Criteria for selecting the GPS antenna location ................................................................... 41 4.4.3 GPS antenna mounted to the RNU4000BS body.................................................................. 41 4.4.4 Multi-sector Daisy-chained GPS Antennas ........................................................................... 42 4.4.4.1 Hardware Interconnections ................................................................................... 42 4.4.4.2 Configuration Parameters...................................................................................... 42 4.5 End-to-End Traffic Test .............................................................................................................. 42 4.5.1 Performing a PING Test .................................................................................................... 43 Field Test Performance Evaluation ................................................................................. 44 5.1 Field Test Overview .................................................................................................................... 44 5.2 Field Test Setup ......................................................................................................................... 45 5.3 Field Test Procedure .................................................................................................................. 47 Technical Specifications ................................................................................................. 49 6.1 RNU4000BS BS Specifications ..................................................................................................... 49 6.2 External Single RF Antennas Specifications .................................................................................. 51 6.2.1 470-678MHz, Single Polarized 90° Sector Antennas Fixed Tilt .............................................. 51 6.3 External Dual-Slant RF Antennas Specifications ............................................................................ 52 6.3.1 698-806MHz, Dual Polarized 65° Sector Antennas Fixed Tilt (AW3052) ................................ 52 6.3.2 698-806MHz, Dual Polarized 90° Sector Antennas Fixed Tilt (AW3054) ................................ 53 6.3.3 Dual-Slant Antenna 2.3-2.7 GHz; 17 dBi;65° (MT-364054/ND) ............................................ 53 6.3.4 Double-dual Slant 2300-2700 MHz Remote Tilt-Panel Antenna ............................................ 55 6.3.5 Dual-Slant Antenna 2.3-2.7 GHz; 16 dBi;60° (SP2327-16XP60NUF) ................................... 56 6.3.6 Dual-Slant Antenna 2.3-2.7 GHz; 15 dBi;90° (SP2327-15XP90NUF) ................................... 57 6.3.7 Dual-Slant Antenna 3.3-3.8 GHz; 17 dBi;65° (MT-404067/ND) ............................................ 58 6.3.8 Dual-Slant Antenna 3.3-3.8 GHz; 17 dBi;65° (SP3338-17XP65) ............................................ 59 6.3.8.1 Radiation Patterns ................................................................................................ 60 SP3338-17XP65 elevation plane .................................................................................................. 60 RNU4000BS Base Station User Manual שגיאה! השתמש בכרטיסיה בית כדי להחילHeading 1.על הטקסט שברצונך שיופיע כאן 6.3.9 Dual-Slant Antenna 3.3-3.8 GHz; 17 dBi;90° (SP3338-17XP90) ............................................ 61 6.3.9.1 Radiation Patterns ................................................................................................ 62 SP3338-16XP90 elevation plane .................................................................................................. 62 6.3.10 Dual-Slant Antenna 4.9-5.95 GHz; 16 dBi;90º (MT-464018/ND) .......................................... 63 6.3.11 Dual-Slant Antenna 470-700 MHz; ..................................................................................... 64 6.4 RNU4000BS Internal Antenna Specifications ................................................................................ 66 6.5 GPS Antenna Specifications ........................................................................................................ 67 RNU4000BS Base Station User Manual Introducing the RNU4000BS BS Runcom's RNU4000BS fully integrated outdoor WiMAX BS provides flexible, cost-effective WiMAX network deployment solutions where increased capacity and coverage is required. ‘All-in-one’ architecture combined with simple, single-handed installation and fast rollout make these BSs an ideal solution for operators that want to get in on the ground floor of WiMAX deployment at significant CAPEX reductions and maximum return on their network deployment. The RNU4000BS is designed for coverage flexibility: depending on the required scenario, the same BS can be configured to cover more sectors with relatively sparse concurrent user requirements or fewer sectors with higher needs. RNU4000BS BSs provide adaptable solutions, allowing interoperability with other MSS devices as well as ASN-GW vendors. Runcom Technologies Ltd. RNU4000BS Base Station User Manual Features • All in one integrated packaging of RF and Base-band components. • Full compliance with IEEE802.16e-2005according to the WiMAX Forum profiles. • Frequency Bands (model dependent): 470-698MHz, 705–745MHz, 1.6-1.8GHz, 2.3-2.7GHz, 3.33.8GHz (CBP capability for band 3.675-3.700GHz is required), 4.9-5.0GHz other bands are optional. • Supports MIMO 2x2, HARQ, and other state of the art features, which increase performance. • 4 channels ready unit – 2 channels supplied by default can be license-key activated for 4 channels. • Transition Power – 2 or 4 x Tx, 24dBm each. • Antenna support - model dependent: four either external or internal antennas. • Integrated GPS receiver for time and clock synchronization with holdover for satellite signal loss. • Flexible coverage capabilities – greater coverage area or greater penetration capabilities • Small footprint, single-handed quick installation and simple provisioning • Fast roll-out for service providers • Seamless and cost-effective integration with a Backhaul network • Optional integrated backhaul link via WiMAX R1 interface • High performance with Quality of Service (QoS) settings, according to WiMAX standards. • Support for the latest R6 interface and GRE tunneling to ASN-GW • Remote NMS management via Runcom’s NMS application Runcom Technologies Ltd. RNU4000BS Base Station User Manual 1.1 Coverage Configurations RNU4000BS supports either two or four RF channels and can provide coverage for either one, two or four sectors depending on the sector density (throughput capacity) and radio performance requirements (note that internal antenna can be used for single sector coverage only): • Single-Sector solution of 4x4 – (for internal and external antennas) – used for higher density sites: four channels for Tx and four channels for Rx MRC. This configuration improves coverage through diversity and improve throughput through MIMO 4x2. • Dual-Sector solution of 2x2 (only relevant for external antennas) – used for lower populated sites: two channels for Tx channels and two channels for Rx MRC. MIMO of 2x2 can be perform if signal to noise ratio is good. • Quad-Sector solution of 1x4 (only relevant for external antennas) – used for more sparsely populated sites: single channel for Tx and single channel for Rx. This configuration is highly cost effective but suffer from lower performance and coverage area per sector (totally it covers more space) The overall capacity, of single base station unit, with respect to the maximum number of connected users, supported bands and throughput is constant; however, in a dual-sector installation, the BS will transmit to two separate sectors in a cell, where each sector is serviced by two antennas. In quad sector installation the BS will transmit to four sectors in a cell (Usually covers the entire cell 3600), where each sector is serviced by one antenna. These two configurations reduce CAPEX and OPAX for operators by covering cells with relatively low density or sparsely populations, which have low requirements for concurrent user’s and / or lower data traffic. The following figure shows a single sector covered by 4x Tx/Rx channels. Several of these sectors (within the same site) should be installed, using the corresponding number of RNU4000BSs, to complete site coverage. Each site can use single GPS antenna, installed on one of the BS, daisy-chained from BS to Runcom Technologies Ltd. RNU4000BS Base Station User Manual another, to perform Figure 1 Single Sector Coverage Runcom Technologies Ltd. RNU4000BS Base Station User Manual • The following figure illustrates dual-sector coverage of two sites by a single RNU4000BS unit. Figure 2 Dual Sector Coverage 1.2 RNU4000BS Interfaces and Accessories The interfaces of the RNU4000BS BS are distributed over two panels. Each of these panels is referred to according to the corresponding interfaces. Note: Install the BS so the power, GPS and communication interfaces face DOWN. 1.2.1 GPS, Power and Communication Interfaces Note: Install the BS on the wall or pole with this panel facing DOWN. Runcom Technologies Ltd. RNU4000BS Base Station User Manual Connector Description GPS Connects to an external (optional) GPS antenna. The GPS antenna is ordered separately. Connector Type: ITT CANNON APD DIN 72585 ETH1 Primary Fast Ethernet connector. Used for initial setup (and standalone tests), and for connection to the backhaul network (in normal installations). Connector Type: RJ-45 TYCO part no 1546907-1 ETH2 Second Ethernet port for local and out-of-band management. In future versions, you will be able to daisy-chain this port to ETH1 in an adjacent Base Station (located in the same BS site) in order to allow a single Ethernet connection to the Backhaul. ETH2 port can also function as a serial port (connection through the cable supplied in the kit). This function is useful if the unit is not accessible via an IP address connection. PPS PPS In and PPS Out can be used for synchronization of multiple sectors, where the PPS Out of one sector is connected to the PPS In of the next BS (daisy chained). This is relevant only for adjacent sectors at the same BS site. See “Multi - Sector Daisy - Chained GPS antennas” section Connector Type: SMA sealed Industrial 48VDC Power connector. External DC power connector (48VDC) for outdoor deployment. Connector Type: RJ-45 GND Ground blind hole connector. In normal installations, connect to the pole on which the unit is mounted. (The BS unit does not include a lightning arrester.) Runcom Technologies Ltd. RNU4000BS Base Station User Manual 1.2.2 BS RF Antenna Interfaces • • RNU4000BS supports either four external or four internal antennas. The unit below shows a model supporting four external antennas. All antennas (internal and external) are 1W each Connector Description ANT1/2/3/4 External RF connector for the Main external antenna. Connector Type: RJ-45 TYCO part no 1546907 1 1.3 Supported Antennas Depending on the model, the RNU4000BS is supplied with four external or four internal dependent. 1.3.1 RF Antennae (not relevant for RNU4000-TVWS) 1.3.1.1 Internal Antennas Four internal antennas: 12dBi each at an azimuth beam-width of 90 degrees. Refer to specifications in section 6.3. 1.3.1.2 External Antenna Four external antennas: 15 to 18dBi, azimuth beam-width dependent. Note: Specs for dual-slant antennas described in section 6.2. You may use any other antenna type or model, keeping in mind that the antenna type or model should be based on the RF planning that was performed in preparation for deployment at the specific site and is dependent upon the coverage and throughput requirements of the site. Runcom Technologies Ltd. RNU4000BS Base Station User Manual 1.4 Optional Accessories The following accessories are not provided with the basic kit, and can be ordered as an option. Element Description Power Supply 110-220v AC/DC converter for 48VDC power supply RF Antenna External directional antenna with pole mounting kit Runcom Technologies Ltd. RNU4000BS Base Station User Manual WEB GUI description Follow by the next steps for BS WEB GUI menu access: • Open Internet Explorer for access to BS WEB GUI using the BS IP address path Figure 3 • BS WEB GUI access path Use the BS WEB GUI credential (user name and password) to obtain the BS WEB GUI menu User name Password user password Figure 4 BS WEB GUI ID This section describes the WEB GUI RNU 4000 Base Station management options and theirs functionalities indented to provide to user the next necessary abilities: • • • • General information (BS HW/SW info, IP status) Monitoring (Synchronization and BS Sector operation status, CPE Connection list info and their link status) Configuration (General RF parameters settings, max. MCS settings and IP settings) Maintenance (Upgrade, Recovery and Default) Runcom Technologies Ltd. RNU4000BS Base Station User Manual 2.1 WEB GUI Menu description The table below describes the WEB GUI Menu options and their functionalities Menu Section General Information Configuration Monitoring General IP Configuration Status Connection CPE Info Description General IP Status General IP Configuration Provides Provides Provides Provides Synchronization BS Status Connection Antenna Status CPE Info Query Provides BS synchronization status Provides BS sector configuration status Provides BS RF parameters configuration status Provides BS antenna configuration status Provides ability to obtain fast link status connection parameters of specific CPE Provides list of connected CPE’s and theirs ID and more detailed connection parameters as link status parameters and theirs SF connection Provides BS SW upgrade including all SW components Provides swap between BS SW version (current running and the previous one) Provides ability to set the BS to default parameters related to the SW version Provides ability to erase the configuration file in case if such file was downloaded to BS CPE List Maintenance Upgrade Recovery SW Upgrade Change Version Reset to Default Default Erase Configuration File BS BS RF BS related HW/SW info ETH interface IP addresses status parameters and MCS settings related IP addresses settings 2.2 WEB GUI working screens description General Information Screen – The figure below represent the “General Information” working screenand provides the next info as described in the table below: Menu General Information Section General IP Status 10 Description Provides BS ID related info: • HW – Product Type • SW – FW /FPAGA version • BS ID – BS MAC address Provides BS ETH interface IP addresses status: • BS ETH interface LAN configuration – IP /subnet/ GW address • ASN GW interface configuration - GW IP and Authentication address for connection with BS • ASN BS DHCP client – ENB/DSB Runcom Technologies Ltd. RNU4000BS Base Station User Manual Figure 5 Runcom Technologies Ltd. General Information –working screen 11 RNU4000BS Base Station User Manual Monitoring screen –The figures below represent the “Monitoring” working screensand provides the next info as described in the table below: Menu Monitoring Status Section Description Synchronization Provides the BS synchronization operational and configuration status: • 1PPS lock status– “Lock” or “Unlock” indicates the 1PPS BS GPS synchronization status • Modem status – indicates the BS RF status: “running” BS RF activated / normal BS operation “Not running” BS RF inactivated / BS is not operational, management is available • 1PPS source – indicates the 1PPS source configuration (see figure “1PPS synchronization source configuration” below) “GPS via Antenna” default configuration • Physical connection status – “Connected” or “Not Connected”- indicates physical connection status of BS external connectors “1PPS input” or “GPS” • GPS lock status – “Lock” or “Unlock” indicates the BS GPS lock status • GPS initialization status – “Initialized” or “Failed” indicates the BS GPS initialization status • Hold over time – “0sec to 14400sec indicates the time of Hold over timer. The timer starts once the BS GPS loss the 1PPS synchronization “Unlock” “14400 sec” default • Hold over time expired – “Not expired” or “expired” indicates the Hold over timer status - Once the timer is expired (14400sec), the BS RF becomes inactivated and that is in order to prevent interference to other BS’s. • Sync change state counter – counting indicates the BS GPS 1PPS synchronization “unlock” states number “ Provides BS sector configuration status info: • Max DL Modulation • Max DL Modulation • Initial Noise – BS receiver initial noise indicates spectrum radio channel quality of the BS working frequency Note: Desirable is to obtain initial noise figure less than 117dbm • Initial TX power Provides BS connection status info: • BS ID – indicates the BS ID • Frequency – indicates the BS central working frequency • Bandwidth Profile – indicates the radio BW and the TX/RX symbols ration • Preamble ID – indicates the BS preamble ID • No. connected UT’s – indicates the quantity of connected CPE’s to the BS • No. of known NBR Bases – Handover feature / indicates the quantity of recognized by BS other neighbor Radio Status WiMAX Connection BS’s Note: N/A for current BS WEB GUI version 12 Runcom Technologies Ltd. RNU4000BS Base Station User Manual Menu CPE Info Section Description Antenna Status Provides BS antenna configuration status: • TX ON/OFF – indicates the BS configuration status of each one transmitter (4 independent transmitters) • RX ON/OFF – indicates the BS configuration status of each one receiver • (4 independent receivers) Provides ability to obtain fast link status connection parameters of specific CPE per CPE MAC address: • UL/DL FEC code type (see table below) • UL/DL CINR • UL RSSI • Max UL subchannel and slots • UL Repetition no. • UL Headroom – remaining CPE TX power Provides list of connected CPE’s ,theirs ID’s and more detailed connection info as link status and SF connection parameters: • Double click on “INFO” in order to obtain Radio Link status parameters and SF parameters CPE Info Query CPE List Runcom Technologies Ltd. FEC Code Type Modulation 13 15 16 17 18 19 20 21 QPSK 1/2 QPSK 3/4 QAM 16 1/2 QAM 16 3/4 QAM 64 1/2 QAM 64 2/3 QAM 64 3/4 QAM 64 5/6 13 RNU4000BS Base Station User Manual 14 Figure 6 Monitoring Status– working screen Figure 7 Monitoring WiMAX– working screen Runcom Technologies Ltd. RNU4000BS Base Station User Manual Monitoring CPE info /CPE list – working screen Figure 8 Figure 9 Monitoring CPE info / link status – working screen Runcom Technologies Ltd. 15 RNU4000BS Base Station User Manual Configuration screen –The figures below represent the “Configuration” working screensand provides the next info as described in the table below: Menu Section Description General General • Provides RF parameters and MCS settings • Provides defined neighbors BS for HO Double click on one of the defined neighbors BS from the list in order to obtain the dialog box for define or update the neighbors BS IP Configuration IP Configuration Provides BS ETH interface IP addresses settings: • BS ETH interface LAN configuration – IP /subnet/ GW address • ASN GW interface configuration - GW IP and Authentication address for connection with BS Note: All ASN related IP configuration in BS should be accordantly to ASN GW configuration Recommended default BS ASN GW and Authentication IP static address is 192.168.0.3 Configuration Stand Alone General Service Flow Profile CPE Binding Multicast Binding 16 • BS DHCP client – ENB/DSB(ASN GW is DHCP server) Note: Normal configuration /static IP configuration DHCP is “DSB” Provide the ability to set the BS network interface operation mode Double click on one of the defined Service Flow profiles from the list in order to obtain the dialog box for define or update the Service Flow profiles Double click on one of the defined CPE binding list in order to obtain the dialog box for binding or update the desirable Service Flow profile with CPE Double click on one of the defined Multicast Binding CPE list in order to obtain the dialog box for Multicast binding or update Runcom Technologies Ltd. RNU4000BS Base Station User Manual Figure 10 Configuration - General screen Figure 11 Configuration – HO neighbors BS definition screen Runcom Technologies Ltd. 17 RNU4000BS Base Station User Manual Figure 12 Configuration - IP Configuration screen Figure 13 Configuration – Stand Alone screen 18 Runcom Technologies Ltd. RNU4000BS Base Station User Manual Figure 14 Configuration – Multicast user definition screen Figure 15 Configuration – CPE network connection screen Runcom Technologies Ltd. 19 RNU4000BS Base Station User Manual Figure 16 Configuration – Service flow profile definition screen Figure 17 20 Configuration – CPE to Service flow profile setting screen Runcom Technologies Ltd. RNU4000BS Base Station User Manual Maintenance screen –The figures below represent the “Maintenance” working screensand provides the next info as described in the table below: Menu Section Description Upgrade SW Upgrade Banks Change Version Allows BS SW upgrade including all SW components: • SW bin – BS SW FW file (required) • FPGA – (required) • HTML bundle – (required) WEB GUI application file • Cfg. file – (Optional) BS configuration file which includes the all BS configuration parameters to be set to obtain BS required configuration Allows swap between BS SW version (current running and the previous one) Allows ability to set the BS to default parameters related to the SW version Allows to erase the configuration file in case if such file was downloaded to BS Allows to upload and viewing the configuration file Maintenance Reset to Default Default Configuration File Erase Configuration File Configuration File Figure 18 Maintenance Upgrade screen Runcom Technologies Ltd. 21 RNU4000BS Base Station User Manual Figure 19 Maintenance Banks screen Figure 20 Maintenance Default screen 22 Runcom Technologies Ltd. RNU4000BS Base Station User Manual Figure 21 Maintenance – Configuration profile file screen Runcom Technologies Ltd. 23 RNU4000BS Base Station User Manual Commissioning Procedure 3.1 Overview Before mounting the RNU4000BS BS on a pole or wall, power should be connected to the BS and the basic parameters configured with the basic parameters using the BS WEB GUI. ATTENTION!!! BE SURE THE RF ANTENNAS ARE CONNECTED OR THE RF PORTS ARE TERMINATED BEFORE CONNECTING POWER TO THE UNIT. The BS commissioning procedure consists of the following steps: 24 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 3.2 Connect BS to Power and Computer ATTENTION!!! BE SURE THE RF ANTENNAS ARE CONNECTED OR THE RF PORTS ARE TERMINATED BEFORE CONNECTING POWER TO THE UNIT. To commission the BS unit two setup connections are required: • • Power - Use the provided (BS) power cable to connect the BS VDC Power connector to an indoor 48 VDC power supply. Computer – Connect the BS ETHER port to the computer running the WEB GUI application. 48VDC Figure 22 BS Commissioning Setup 3.2.1 Configure the Computer's Network Parameters In order to establish communication between the computer and the BS perform the following: • • 3.2.1.1 Assign computer IP address in the same subnet as the BS Disable Firewall Configure Computer IP Address To configure IP address follows the next steps: Note: The procedure may vary slightly depending on the operating system installed on the computer. The following procedure is for Windows XP. 1. Click the Start menu and choose Network Connections. 2. Right-click the Local Area Connectioncorresponding to the BS connection and select Properties. Runcom Technologies Ltd. 25 RNU4000BS Base Station User Manual The Local Area Connections Properties dialog appears with the General tab displayed by default. 3. In the Items list, select “Internet Protocol (TCP*IP)” and click the Properties button. The “Internet Protocol (TCP/IP) Properties” dialog appears. 26 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 4. In the IP Address display area: • • In the IP address field assign an IP address other than the BS IP address (Default BS IP Address: 192.168.0.20). In the Subnet mask – set the subnet to the same subnet as the BS (Default BS Subnet: 255.255.255.0). (It is not required to define the Default Gateway). 5. Click OK. Runcom Technologies Ltd. 27 RNU4000BS Base Station User Manual 3.2.1.2 Disable Firewall To disable firewall follow the next steps: 1. In the Local Area Connection dialog, click the Advanced tab. The following dialog appears. Advanced tab Settings button 2. In the Windows Firewall display area click the Settings button. The Windows Firewall dialog appears. 3. Select the Off option and click OK. 28 Runcom Technologies Ltd. RNU4000BS Base Station User Manual Installing the RNU4000BS BS After commissioning the RNU4000BS BS, the unit is ready for installation. The procedure consists of the following steps: • • • • • • • Choosing the installation location and mounting the BS on a pole or on a wall For models with external RF antennas, mounting the RF antennas in the appropriate locations Mounting the GPS antennas in the appropriate locations Connecting the RF antenna to the BS Assembling the GPS antennas to the BS using the provided bracket Connecting Ground, Power and ETH cables to the BS Performing an End-to-End traffic test 4.1 Mounting the Base Station The RNU4000BS BS is provided with a mounting kit which includes all the mounting elements (e.g. mounting-bracket, torques, screws etc.). The BS can be mounted either on a pole or on a wall. Note: The same mounting bracket is used for the wall and the pole installation. When mounting the BS, note the following • • The RNU4000BS BS is typically installed in an upright vertically aligned position with the power, Ethernet and GPS connectors facing DOWN. The RNU4000BS BS should be installed on the rear side of the RF antenna to prevent self-reflections. 4.1.1 BS Installation Location This section describes the criteria that should be considered when selecting the RNU4000BS BS installation location. The BS can be mounted on either a pole or a wall. To choose BS Installation location • • • • • • Verify that the pole/wall location corresponds to the site plan and takes into account local regulations and maintenance access. The unit should be mounted in the highest possible point. Reception will increase according to the height of the antennas. The diameter of the pole on which the base station and antenna are to be mounted is either: • 1.00-1.75” or • 1.75-3.00” Verify that the pole is properly grounded. Verify that the pole has lightening protection. Verify that there is safe access to the pole, free of any obstacles or other danger for installers of the RNU4000BS BS. Runcom Technologies Ltd. 29 RNU4000BS Base Station User Manual • Verify that there are no power lines near the pole. 4.1.2 Mounting Bracket Description The figure below shows the BS mounting bracket. Note: The same mounting bracket is used for the wall and the pole installation. WALL/POLE RACKET BASE ARM CLAMPING BRACKET Use for securing bracket to pole The Bracket elements are described in the following table. Element Description BRACKET BASE. This part is connected to the BS. BRACKET ARM. This part provides the tilt ability, and connects between the Bracket BASE and MAIN SUPPORT. 30 Runcom Technologies Ltd. RNU4000BS Base Station User Manual Element Description WALL/POLE BRACKET Used for connecting the bracket to the wall. CLAMPING BRACKET Used for securing the bracket to the pole. Provided screws, nuts and washers: A C A. 4x flat washer M5 B. 4x nut M5 C. 4x spring washer M5 (seems as flat washers) D. 4x bolt M8x50 E. 4x washer spring M8 F. 4x washer flat M8 G. 2x nut M8 H. 2x bolt M8x70 I. Runcom Technologies Ltd. 4x bolt M5x16 - missing 31 RNU4000BS Base Station User Manual 4.1.3 Mounting On a Pole Note: When installing on a pole, leave at least 40cm space between the BS and the top of the pole for lightning protection. To install the BS on a pole 1. Secure the BracketBase to the BS underside: • Secure the Bracket Base to the underside of the BS, using the provided screws, as shown below: Secure to BS Underside • • 32 BASE Verify that the orientation of the hole in the BASE is aligned with the elevation axis. Use a tightening torque of 5.7N/m to tighten. Runcom Technologies Ltd. RNU4000BS Base Station User Manual 2. Assemble the bracket elements: • Secure the WALL/POLE BRACKET to the Bracket Arm and then to the BracketBase using the provided screws, as shown below: BASE - connect to BS WALL/POLE BRACKET Ridges to ridges ARM Washers and bolt Note: The bolt head should be positioned in the socket on the Bracket BASE. • Use a tightening torque of 24 N/m to tighten. 3. Mount the BS on the pole, where the procedure varies slightly according to the pole diameter: For poles with a diameter of 1.75-3.00”: POLE SUPPORT Assembled CONVEX on the pole • • • Mount the BS on the pole using the bracket Pole Support as shown above. Assemble the bracket CONVEX as shown. Tighten the bracket using the provided screws, according to the pole diameter. Use a tightening torque of 14N/m to tighten. Runcom Technologies Ltd. 33 RNU4000BS Base Station User Manual For poles with a diameter of 1.00-1.75”: CLAMPING BRACKET Assembled CONCAVE on the pole • • • Mount the BS on the pole using the Clamping Bracket as shown above. Assemble the bracket CONCAVE as shown. Tighten the bracket using the provided screws. Use a tightening torque of 14N/m to tighten. 4.1.4 Mounting On a Wall 1. Secure the BracketBase to the BS underside: • Secure Bracket Base to the underside of the BS, using the provided screws, as shown below: Secure to BS Underside • • BASE Verify that the orientation of the hole in the BASE is aligned with the elevation axis. Use a tightening torque of 5.7N/m to tighten. 2. Assemble the bracket elements: • 34 Secure the Bracket Arm to the BracketBase using the provided screws, as shown below: Runcom Technologies Ltd. RNU4000BS Base Station User Manual BASE Assemble to BS Ridges to ridges i ARM Washers and bolt Note: The bolt head should be positioned in the socket on the Bracket BASE. 3. Mount the BS on the wall: • Mount the WALL/POLE BRACKET on the wall in the appropriate position. Note the azimuth orientation when doing so. WALL/POLE BRACKET Secure to a wall Secure to wall Runcom Technologies Ltd. 35 RNU4000BS Base Station User Manual • Attach the Bracket Arm to the WALL/POLE BRACKET using the provided screws. WALL/POLE BRACKET ARM Note: • The bolt head should be positioned in the ARM socket. Use a tightening torque of 24 N/m to the azimuth and elevation hardware. 4.2 Overview of the Cable and Power Connections This section provides a summary of the cable connections. Mounting and connections are described in detail in the following sections. BS Connections: ATTENTION!!! BE SURE THE RF ANTENNAS ARE CONNECTED OR THE RF PORTS ARE TERMINATED BEFORE CONNECTING POWER TO THE UNIT. • • • • RF Antennas:(For models with external RF antennas). Connect coax cables from each RF antenna to the base station ports ANT1/ANT2/ANT3/ANT4. GPS Antenna: Connect a coax cable (10 meters max) from the GPS antenna to the BS GPS connector. Ground: Use the provided grounding cable to ground the BS to the pole (if pole is grounded), or to a grounding point. Power: Run the 5-10 meter power cable from the BS Power connector down the pole, to the provided 48 V power converter that is located indoors (i.e. in a building or in a caravan). Note: It is recommended to connect a battery (for backup) to the 48VDC power supply. • 36 Ethernet: Run the 5-10 meter Ethernet cable of the base station from the ETH connector at the bottom of the base station down the pole and connect it to an indoor Ethernet connector, such as in a building or in a caravan Runcom Technologies Ltd. RNU4000BS Base Station User Manual If necessary, secure the cables to the pole so that it is not loose using plastic strips. 40cm from TOP of pole GPS Antenna Double Dual-Slant RF Antennas Cables for 4 RF Antennas GPS Cable (10 meters max) X4 Antennas BS GPS GND ETH Grounding Cable (connected to pole – if grounded, or to other grounding point) 5-10 Meters Power Cable 5-10 Meters ETH Cable Building ROOF 48VDC 48VDC Battery ETH: Indoor Ethernet Connection BUILDING Figure 23 Overview BS Connections Runcom Technologies Ltd. 37 RNU4000BS Base Station User Manual 4.3 Mounting the RF Antennas After mounting the base station on a pole or wall: • • For models with external RF antennas, mount the RF antennas in the selected locations according to the instructions given in this section. Mount the GPS Antenna in the selected locations according to the instructions given in this section. 4.3.1 Mounting the RF Antenna Note: This section is relevant only for installations of BSs with external antennas. Refer to section 1.1 for more information on antenna configurations. 4.3.1.1 RF Antenna Location Criteria • • 4.3.1.2 To avoid frequency reuse problems caused by unwanted reflections, the main part of the antenna must be clear of any metal objects for a range of parameter to 20 meters. Make sure that there are no obstacles located in front of the RF antenna, such s poles, transmission equipment from other vendors or another Runcom RF antenna. RF Antenna Mounting Note: The antenna is mounted and adjusted using the provided antenna mounting kit. To mount the RF Antennas: • • • • Use the supplied RF antenna (pole) mounting kit to attach the antenna to the pole. Connect the antennas to the BS using the provided 0.5 -1 meter coax cables. Tilt the antenna as required. The antenna’s mounting kit enables the antenna to be tilted along two axes. The antenna position can be fine-tuned at a later stage. Figure 24 RF Antennas Mounting 38 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 4.3.1.3 4x4 antennas Outdoor Connection Requirements Pico BS 4x4 antennas require using Antennas Dual Slant type (with polarization). Antennas connection should be accordantly: • • • • BS “Ant 1” connector → connected via RF cable →to Antenna 1 “Port 1” or connector BS “Ant 2” connector → connected via RF cable →to Antenna 2 “Port 1” or connector BS “Ant 3” connector → connected via RF cable →to Antenna 1 “Port 2” or connector BS “Ant 4” connector → connected via RF cable →to Antenna 2 “Port 2”or connector “ANT1” “ANT1” “ANT2” “ANT2” Note: Reason for Requirement is to obtain proper downlink throughput ,each BS TX stream should be with different polarity Figure 25 BS Antennas Connection Figure 26 BS Antennas Polarization Connection Description Runcom Technologies Ltd. 39 RNU4000BS Base Station User Manual 4.4 Pole Mounted GPS Antenna The following is an example of a pole mounted GPS antenna for single-sector coverage. 40 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 4.4.1 GPS Antenna Installation The GPS active antenna may be mounted using two different methods: • • Attached to a pole or other hosting surface using a magnet Mounted to the RNU4000 unit using the supplied bracket. For coverage of multi-sector sites using a number of BSs, one GPS antennas can serve a number of interconnected and synchronized BSs. The Pole and bracket mounting methods as well as the multi-sector GPS coverage are described in this section. Note: The Holdover time (duration that BS synchronization is retained – from the point in time in which the GPS antenna is disconnected) is determined by the internal GPS. Currently – approximately 8 hours. 4.4.2 Criteria for selecting the GPS antenna location • • The whole antenna area is exposed to the sky. GPS antenna should not be more than 10 meters from the RNU4000BS (excessive cable length may cause interference).Bracket Mounted GPS Antenna The GPS antenna can be assembled on to the RNU4000BS unit using the supplied. 4.4.3 GPS antenna mounted to the RNU4000BS body • • • Assemble the bracket to the underside of the unit as illustrated in the following image. Connect the GPS antenna to the RNU4000BS GPS connector using a coax cable. Assemble the GPS antenna to the bracket as illustrated. Figure 27 GPS Antenna to Bracket Connections Runcom Technologies Ltd. 41 RNU4000BS Base Station User Manual 4.4.4 Multi-sector Daisy-chained GPS Antennas This section describes how to connect and synchronize GPS antennas for multi-sector sites covered by a dedicated RNU4000BS unit per site (x4 Tx/Rx channels per site). The BSs can be connected in two configurations: • • 4.4.4.1 One GPS antenna can serve all the BSs For redundancy - each BS can operate with a dedicated GPS antenna. Hardware Interconnections The figure below illustrates a daisy-chain configuration for a four-sector base station site with four RNU4000 units. Each unit has an integrated GPS module, and an internal holdover circuit responsible for providing a 1PPS signal in case of loss of PPS source (from either the integrated GPS unit or the PPS IN port). Figure 28 GPS Synchronization Connection - (daisy-chain) 4.4.4.2 Configuration Parameters For synchronization configuration and indication details description parameters refer to “WEB GUI” section. 4.5 End-to-End Traffic Test After the system is installed, it is recommended to perform an End to End (E2E) test to test communication and traffic transference over the link. In this test, a computer connected to a CPE (that is configured to operate with the BS) sends a ping message towards the NOC (Network Operations Center) and AAA (Authentication, Authorization and Accounting center). Receiving an answer from the NOC/AAA side by the CPE's PC assures that the system is configured and operating properly. The following figure shows the end-to-end test elements. 42 Runcom Technologies Ltd. RNU4000BS Base Station User Manual To perform the test 1. Ensure that the BS is configured with the: • • Center frequency ASN-GW IP address and security parameters 2. Connect the BS to a CPE configured with the: • Center Frequency 3. Connect a computer configured to communicate with the CPE– using the CPE IP address subnet) to the CPE Ethernet port using a cross-cable. 4. Use Telnet to send a ping command from the CPE computer to the NOC IP Address. 4.5.1 Performing a PING Test To verify connectivity 1. Open a Command Prompt window from the computer connected to the CPE 2. Select Start Run and enter cmd. 3. Enter a Ping command that pings the NOC. The following shows a Ping command: 4. Verify that the link has been established properly according to the reply received from the NOC. 5. If no 'ping' reply is received, check connections and required configuration parameters. Runcom Technologies Ltd. 43 RNU4000BS Base Station User Manual 5 Field Test Performance Evaluation The purpose of this document is to validate in the field performance of Runcom system that includes base station and CPEs (with or without NOC) in the operation modes. The field tests cover MIMO-A (Matrix A or SISO) and MIMO B (Matrix B). This document contains the following main sections that describe the test performance: • Throughput performance per CINR and MCS (modulation coding scheme) The table below describes the test equipment list and the associated accessories in order to perform the test as described in this document Equipment QTY Parameters Outdoor Compact BTS 4x4 IDU CPE ODU CPE 4x30dbm, 65 or 90 degrees sector antenna 16dbi 2x24dbm, panel antenna 2x7dbi or 2x15dbi 2x24dbi, omni antennas 2x5dbi USB 1x17-20dbm, on board antenna CNOC License for 100 subscribers 10MHz (or 5MHz) 32/15 (or 26:21 for higher UL) 4x0dB MAX 4X30dB MAX QAM 64 2/3 QAM 16 ¾ for Lab test for field test For mobile For mobile RF Configuration BW TX/RX symbols ratio TX power DL Modulation max UL Modulation max Network Configuration Service Flow Default BE, UGS, nRTPS CIR 64Kb MIR DL 40Mbs/UL 40Mbs All users Advance Configuration Special settings MIMO-B mode BS CINR Threshold table parameters BS Synch Configuration GPS for external use For field test Internal clock For Lab test 5.1 Field Test Overview The field test testing procedures is used to evaluate the throughput performance and the base station sector coverage performance in LOS and N-LOS environment. To get more robust reliable measurements results for better analysis the recommended conditions for the testing points are LOS environment. Note: 44 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 1. For MIMO B operation mode the DL CINR should be 25db 2. For maintaining the MIMO B mode the recommended set up is LOS or Near-LOS. 5.2 Field Test Setup The setup presented here is a suggestion for a general setup which allows the operation of the tests as described in this document. Figure 29 Test Setup Diagram Figure 30 Field Test Setup Runcom Technologies Ltd. 45 RNU4000BS Base Station User Manual Figure 31 Field Test Point Sector 1 120° BS Site Figure 32 Sector Radio Coverage 46 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 5.3 Field Test Procedure Preliminary preparation 1. Establish the test setup and the outdoor installation according to the figure “Field Test Setup” or equivalent 2. Establish connection between the BS and the CPE and required settings to obtain proper connection Perform PC to PC TCP throughput performance using measurement tools: • FTP “FileZilla Server” (Setting Buffer size = 491520/Socet buffer size=983040) • 5 sessions (file size 80 Mb each) running simultaneously on CPE in complete LOS DL Throughput performance SISO/ MIMO B DL link Modulation RSSI[dB] CINR DL Throughput (max) [Mb/s] [dB] Radio BW 10MHz TX/RX symbols ratio 32:15 64 QAM 5/6 (MIMO-B) 64 QAM 2/3 (MIMO-B) 16 QAM ¾ (MIMO-B) 64 QAM 2/3 (SISO) 16QAM ¾ (SISO) 16QAM ½ (SISO) QPSK ¾ (SISO) QPSK ½ (SISO) -55 -58 -65 -70 -75 -78 -80 -83 27 25 22 20 17 14 11 37 30 22 14.5 11 7.5 5.5 3.5 Note: 1. Throughput performance measurements values tolerance -5% 2. CINR measure values tolerance ±2dBm 3. RSSI values tolerance ±3dBm DL Throughput performance SISO table - theoretical calculation / symbol ratio 32:15 DL Modulation QPSK 1/2 QPSK 3/4 QAM 16 1/2 QAM 16 3/4 QAM 64 1/2 QAM 64 2/3 QAM 64 3/4 QAM 64 5/6 Runcom Technologies Ltd. DL CINR threshold 11 14 17 20 22 24 25 DL Throughput (max) DL Throughput (max) [Mb/s] BW 10MHz Radio BW 5MHz [Mb/s] TX/RX symbols ratio 32:15 12 12 16 18 20 10 47 RNU4000BS Base Station User Manual UL Throughput performance SISO - theoretical calculation / symbol ratio 32:15 DL Modulation DL CINR threshold DL Throughput (max) BW 10MHz DL Throughput (max) BW 5MHz [Mb/s] [Mb/s] QPSK 1/2 QPSK 3/4 QAM 16 1/2 QAM 16 3/4 12 1.34 2.68 0.6 1.34 DL Throughput performance MIMO B table - theoretical calculation / symbol ratio 32:15 DL Modulation DL CINR threshold DL Throughput (max) BW 10MHz DL Throughput (max) BW 5MHz [Mb/s] [Mb/s] QAM 16 3/4 QAM 64 2/3 QAM 64 5/6 48 20 22 25 24 32 40 12 16 20 Runcom Technologies Ltd. RNU4000BS Base Station User Manual Technical Specifications The RNU4000BS BS installation procedure involves the following accessories: • • • RF Antennas GPS Antenna (Optional) Mounting kit This section details the specifications for the RNU4000BS BS and accessories. 6.1 RNU4000BS BS Specifications Radio Standard compliance complies with 802.16e according to the WiMAX Forum profiles. WiMax Fixed and Mobile Number of sectors 1, 2 or 4 sectors System Capability LOS, Near LOS, Non LOS Frequency 470-698MHz (TV white space), 700 – 750MHz, 1.6-1.8GHz, 2.32.7GHz, 3.3-3.8GHz (CBP capability for band 3.675-3.700GHz is required),4.9-5.0GHz, 5.0-5.15GHz, 5.7-5.8GHz, 5.96.4GHz(Model Dependent) other frequencies are optional FFT 512, 1024, 2048 FEC Convolution Code and Turbo Code Channel bandwidth 3.5 MHz, 5 MHz, 7 MHz, 8.75 MHz, 10 MHz, optional 20 MHz Duplex method TDD, optional FDD/HFDD Central frequency resolution 125 KHz Maximum output power (on antenna connector) +30dBm +28 dBm per antenna in 4.9GHz and above +24dBm per antenna port in TVWS band Antennas: Type Integrated Sectored 11dBi (90°) (not for TVWS) External dual slant External Single antenna Number 2 dual-slant; 4 Single Connectors 4x N-Type, 50 ohm, lightning protected (Optional) Modulation and coding rates DL/UL: QPSK (1/2, 3/4) , 16 QAM (1/2, 3/4), 64 QAM (2/3 , 3/4, 5/6 ) (64 QAM is optional for UL) Diversity Supported MIMO A/B , STC, MRC, SISO, GPS Integrated Synchronization Integrated GPS module with on board synchronization unit Runcom Technologies Ltd. 49 RNU4000BS Base Station User Manual Management Network Management SNMPv2/v3, standard and proprietary MIB System Configuration SNMP, FTP, CLI Software Upgrade Remote TFTP upgrade of firmware and programming Interfaces Network Interfaces 2x10/100 Base-T, Optional 1xGE and optical interface SX/LX Northbound Interface Profile C, R6 per SF GRE tunnel, Profile B is optional Connectors 2xN-Type for external antenna 50 ohm, External synchronization option, external GPS antenna option, power connector, 2xRJ-45 Electrical Characteristics Power Source -36 to -72 VDC < 60Watt Physical and Environmental Dimensions 39cm (L) x 24cm (W) x 12cm (H) Weight 5000 grams / not including mounting kit Operating external temperature Industrial -40°C to 55° C Operating humidity 95% non-condensing Standards Compliance* Safety EN 60950-1, EN 60950-22 Environmental IEC 60529-1, IP66 Radio FCC Part 27 , Part 90; EN302 623 , EN302 544 For TVWS comply with FCC Part 15 sub-part H EMC 50 FCC part 15, class B ; ETSI EN 301489-1 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.2 External Single RF Antennas Specifications 6.2.1 470-678MHz, Single Polarized 90° Sector Antennas Fixed Tilt Electrical Frequency Range 470MHz – 700MHz Gain 6 dBi Return Loss (VSWR) <1.3 Azimuth Beam width Vertical 90º (typ) Polarization Horizontal or Vertical Power Handling 50W Front-to-Back Ratio >15dB Input Impedance 50 (ohm) Electrical Downtilt 0º Lightning Protection Direct Ground Mechanical DIMENSIONS (LxWxD) 850mm WEIGHT 0.4 kg Connector / Cable Cable mount, F connector Connection Location Center Runcom Technologies Ltd. 51 RNU4000BS Base Station User Manual 6.3 External Dual-Slant RF Antennas Specifications 6.3.1 698-806MHz, Dual Polarized 65° Sector Antennas Fixed Tilt (AW3052) Electrical Frequency Range 698MHz – 806MHz Gain 13.5 dBi Return Loss (VSWR) >14dB (1.5:1) Azimuth Beam width @ 13.5dBi 65º (typ) Polarization Dual Slant (+/-45°) Upper Side lobe Suppression >18dB Horizontal 3dB BW 65º Vertical 3dB BW 17º Power Handling 300W Front-to-Back Ratio >25dB Isolation >30dB Input Impedance 50 (ohm) Electrical Downtilt 4º Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 1220 x 300 x 150mm WEIGHT 13 kg Connector 2 x 7/16 DIN Female Connection Location Bottom RADOME UV Stabilized Styrosun 52 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.3.2 698-806MHz, Dual Polarized 90° Sector Antennas Fixed Tilt (AW3054) Electrical Frequency Range 698MHz – 806MHz Gain 12.5 dBi Return Loss (VSWR) >14dB (1.5:1) Azimuth Beam width @ 13.5dBi 90º (typ) Polarization Dual Slant (+/-45°) Upper Sidelobe Suppression >18dB Horizontal 3dB BW 65º Vertical 3dB BW 17º Power Handling 300W Front-to-Back Ratio >25dB Isolation >30dB Input Impedance 50 (ohm) Electrical Downtilt 4º Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 1220 x 300 x 150mm WEIGHT 13 kg Connector 2 x N Female Connection Location Bottom RADOME UV Stabilized Styrosun 6.3.3 Dual-Slant Antenna 2.3-2.7 GHz; 17 dBi;65° (MT-364054/ND) Electrical Gain 16 dBi (min) @ 2.3 - 2.5 GHz 17.5±0.5 dBi @ 2.5 - 2.7 GHz VSWR 1.5:1 (typ), 1.7 :1(max) Azimuth Beam width @ 13.5dBi 65º (typ) Elevation Beam width @ -3 dB 7º (typ) Polarization Dual Linear, ± 45º Cross-polarization -20 dB (max) @ 2.3 - 2.5 GHz -17 dB (max) @ 2.5 - 2.7 GHz Side Lobes Level Azimuth and Elevation Runcom Technologies Ltd. Meets ETSI EN 302 326- V1.1.2 (2006-03) 53 RNU4000BS Base Station User Manual Side Lobes Level for Azimuth in the range -20 dB (max) @ 2.3 - 2.5 GHz (± 100 to ± 180 from Boresight) -25 dB (max) @ 2.5 - 2.7 GHz Front-to-Back Ratio -30 dB (max) Port-to-Port Isolation 23 dB (min), 30 dB (typ) Input Impedance 50 (ohm) Input Power 20 W (CW), 250 W (peak) Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 945 x 126 x 37mm (max) WEIGHT 3.0 kg (max) CONNECTOR 2 x N-Type Female RADOME Plastic UV Resistant BASE PLATE Aluminum with chemical conversion coating MECHANICAL DOWN TILT 0º to (-10º) 54 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.3.4 Double-dual Slant 2300-2700 MHz Remote Tilt-Panel Antenna Electrical Frequency Range 2300-2700 MHz Gain 17.1 dBi @ 2.4 GHz 17.8 dBi @ 2.6 GHz Return Loss > 15 dB Polarization Dual Slant ± 45° Horizontal Beamwidth 65° Vertical Beamwidth 7° with nullfill Electrical Downtilt 0° - 10° independently continuously adjustable Upper Sidelobe Level < -18 dB Front to Back Ratio > 30 dB Isolation Between Ports > 30 dB Power Rating 250 W Impedance 50 ohm Lightening Protection DC Grounded Connector Type N-Type Female RET Type Internal motor & manual override RET Interface AISG 2 Remotely upgradeable RET Connector Single AISG 8 pin male Mechanical Antenna Dimensions 1070x300x115 mm Packed Dimensions 1200x330x200 mm Antenna Weight 13 kg Radom Material Polyester Fiberglass Runcom Technologies Ltd. 55 RNU4000BS Base Station User Manual 6.3.5 Dual-Slant Antenna 2.3-2.7 GHz; 16 dBi;60° (SP232716XP60NUF) Electrical Gain 16 dBi @ 2.3-2.5 GHz 16.5 dBi @ 2.5-2.7 GHz VSWR 1.5 : 1 (max) Azimuth Beamwidth @ 13.5dBi 60º +/- 5º Elevation Beamwidth @ -3 dB 9º (typ) Polarization Dual Linear, ± 45º Front-to-Back Ratio -25 dB (Min) EN 302 326 V.1.1.2 (2006-03) Port-to-Port Isolation 30 dB (typ) @ 2.3-2.7 GHz Null Fill 1st Sidelobe: -15dB 2nd Sidelobe: -18dB Input Impedance 50 (ohm) Input Power 20 W (CW), 250 W (peak) Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 711x171x90mm (max) WEIGHT 3.1 kg (max) CONNECTOR 2 x N-Type Female RADOME Gray UV resistant plastic MECHANICAL DOWN TILT 0º to (-10º) 56 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.3.6 Dual-Slant Antenna 2.3-2.7 GHz; 15 dBi;90° (SP232715XP90NUF) Electrical Gain 14.5 dBi @ 2.3-2.5 GHz 15 dBi @ 2.5-2.7 GHz VSWR 1.5 : 1 (max) Azimuth Beamwidth @ 13.5dBi 90º +/- 5º Elevation Beamwidth @ -3 dB 9º (typ) Polarization Dual Linear, ± 45º Front-to-Back Ratio EN 302 326 V.1.1.2 (2006-03) -25 dB (Min) Port-to-Port Isolation 30 dB (typ) @ 2.3-2.7 GHz Null Fill 1st Sidelobe: -15dB 2nd Sidelobe: -18dB Input Impedance 50 (ohm) Input Power 20 W (CW), 250 W (peak) Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 711x171x90mm (max) WEIGHT 3.1 kg (max) CONNECTOR 2 x N-Type Female RADOME Gray UV resistant plastic MECHANICAL DOWN TILT 0º to (-10º) Runcom Technologies Ltd. 57 RNU4000BS Base Station User Manual 6.3.7 Dual-Slant Antenna 3.3-3.8 GHz; 17 dBi;65° (MT-404067/ND) Electrical Gain 16 dBi (min) @ 3.3-3.4 GHz 17.5 ±0.5 dBi @ 3.5-3.8 GHz VSWR 1.5 : 1 (typ) 1.8:1 (max) Azimuth Beamwidth @ 13.5dBi 65º (typ) Elevation Beamwidth @ -3 dB 7.5º (typ) Polarization Dual Linear, ± 45º Cross-polarization ETSI EN 302 326 V.1.1.2 (2006-03) Side Lobes Level Azimuth and Elevation Meets ETSI EN 302 326- V1.1.2 (2006-03) Side Lobes Level for Azimuth in the range -25dB (max) @ 3.3-3.5 GHz (± 100 to ± 180 from Boresight) -30dB (max) @ 3.5-3.8 GHz Front-to-Back Ratio -30 dB (max) EN 302 326 V.1.1.2 (2006-03) Port-to-Port Isolation 25 dB (min) @ 3.3-3.7 GHz 20 dB (min) @ 3.7-3.8 GHz Input Impedance 50 (ohm) Input Power 20 W (CW), 250 W (peak) Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 600x130x63mm (max) WEIGHT 2.5 kg (max) CONNECTOR 2 x N-Type Female RADOME Plastic UV Resistant BASE PLATE Aluminum with chemical conversion coating MECHANICAL DOWN TILT 0º to (-10º) 58 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.3.8 Dual-Slant Antenna 3.3-3.8 GHz; 17 dBi;65° (SP3338-17XP65) Electrical Gain 16.5 dBi @ 3.3-3.5 GHz 17dBi @ 3.5-3.8 GHz VSWR 1.5 : 1 (max) Azimuth Beamwidth @ 13.5dBi 65º +/- 5º Elevation Beamwidth @ -3 dB 7º (typ) Polarization Dual Linear, ± 45º Upper Side Lobe Suppression -15dB @ 3.3-3.8 GHz 30 degrees above horizon Front-to-Back Ratio -25 dB (Min) EN 302 326 V.1.1.2 (2006-03) Port-to-Port Isolation 30 dB (typ) @ 3.3-3.8 GHz Input Impedance 50 (ohm) Input Power 20 W (CW), 250 W (peak) Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 711x171x90mm (max) WEIGHT 3.1 kg (max) CONNECTOR 2 x N-Type Female RADOME Gray UV resistant plastic MECHANICAL DOWN TILT 0º to (-10º) Runcom Technologies Ltd. 59 RNU4000BS Base Station User Manual 6.3.8.1 Radiation Patterns SP3338-17XP65 azimuth plane SP3338-17XP65 elevation plane 60 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.3.9 Dual-Slant Antenna 3.3-3.8 GHz; 17 dBi;90° (SP3338-17XP90) Electrical Gain 15.5 dBi @ 3.3-3.5 GHz 16 dBi @ 3.5-3.8 GHz VSWR 1.5 : 1 (max) Azimuth Beamwidth @ 13.5dBi 90º +/- 5º Elevation Beamwidth @ -3 dB 7º (typ) Polarization Dual Linear, ± 45º Upper Side Lobe Suppression -15dB @ 3.3-3.8 GHz 30 degrees above horizon Front-to-Back Ratio -25 dB (Min) EN 302 326 V.1.1.2 (2006-03) Port-to-Port Isolation 30 dB (typ) @ 3.3-3.8 GHz Input Impedance 50 (ohm) Input Power 20 W (CW), 250 W (peak) Lightning Protection DC grounded Mechanical DIMENSIONS (LxWxD) 711x171x90mm (max) WEIGHT 3.1 kg (max) CONNECTOR 2 x N-Type Female RADOME Gray UV resistant plastic MECHANICAL DOWN TILT 0º to (-10º) Runcom Technologies Ltd. 61 RNU4000BS Base Station User Manual 6.3.9.1 Radiation Patterns SP3338-17XP90 azimuth plane SP3338-16XP90 elevation plane 62 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.3.10 Dual-Slant Antenna 4.9-5.95 GHz; 16 dBi;90º (MT-464018/ND) Electrical Gain 16 dBi (min) @ 4.9-5.95 GHz VSWR 2 : 1 (max) 1.7:1 (typ) 4dB Azimuth Beam width 90º (typ) Elevation Beam width @ -3 dB 6.0º (typ) Polarization Dual Linear, ± 45º Cross-polarization ETSI EN 302 326 V.1.1.2 (2006-03) EL upper side lobes level 25dB (typ Front-to-Back Ratio -25 dB (max) Port-to-Port Isolation 25 dB (typ) 22dB (min) Input Impedance 50 (ohm) Input Power 20 W (CW), 250 W (peak) Lightning Protection DC grounded Mechanical Antenna Dimensions 550x250x17 mm Connector 2xN-Type Female Antenna Weight 2.5 kg Radom Material Plastic Runcom Technologies Ltd. 63 RNU4000BS Base Station User Manual 6.3.11 TVWS Panel Antenna 470-700 MHz; Electrical Gain 7 dBi VSWR < 1.8:1 Horizontal Beam width (at -3 dB, depends on frequency) Vertical Beam width (at -3 dB, depends on frequency ) Elevation Beam width @ -3 dB 90° 33° - 21° Polarization Vertical Cross-polarization isolation 30 dB Front-to-Back Ratio 20dB Port-to-Port Isolation 30dB Input Impedance 50 ohm Input Power 10W max. Lightning Protection DC Grounded Elements Mechanical Antenna Dimensions 1050x500x200 mm Connector N Type Antenna Weight TBD Radom Material Plastic 64 Runcom Technologies Ltd. RNU4000BS Base Station User Manual Runcom Technologies Ltd. 65 RNU4000BS Base Station User Manual 6.4 RNU4000BS Internal Antenna Specifications Specifications for 2.5 GHz / 3.5 GHz/4.9GHz Electrical 2.5 GHz 3.5 GHz 4.9 GHz 4x Sector 4 x Sector 4 x Sector Frequency Range 2.3 – 2.7 GHz 3.3 – 3.8 GHz 4.9 - 5.1 GHz Gain + 11.5 dBi x 2 + 11.5 dBi x 2 +12dBi x 2 VSWR 1.6:1 1.6:1 1.7:1 3 dB Azimuth Beam width 110° 110° 90° 3 dB Elevation Beam width 30° 20° 22° Dual Slant ± 45° Dual Slant ± 45° Dual Slant ± 45° Cross Polarization -30 dB -27 ± 3 dB -35dB F/B Ratio -25 dB -25 dB -23dB Antenna Model Polarization Mechanical Form Factor RNU4000BS Enclosure Integrated Dimensions 236.0 x 79.5 x 48.2 mm (without connectors) 66 Runcom Technologies Ltd. RNU4000BS Base Station User Manual 6.5 GPS Antenna Specifications GPS Active Antenna (BY/GPS/06) Dielectric Center Frequency 1575.42 MHz ± 3 MHz VSWR 1.5:1 Bandwidth ±5 MHz Impedance 50 ohm Peak Gain >3 dBic Based on 7×7cm ground plane Gain Coverage >- 4 dBic at –90°<0<+90°(over 75% Volume) Polarization RHCP LNA Filter LNA Gain (without cable) 28 dB Typical Noise Figure 1.5 dB Filter Out of Band Attenuation (f0=1575.42 MHz) 7dB Min f0+/-20MHZ 20dB Min f0+/-50MHZ 30dB Min f0+/-100MHZ VSWR < 2.0 DC Voltage 3.0V to 5.0V DC Current 10mA Max Mechanical Weight < 110 gr Dimensions D x H 46 mm x 15 mm Cable RG174 3m or other Connector SMA/SMB/SMC/BNC/FME/TNC/MCX/MMCX or other Mounting Screw Mount Housing Black Environmental Operating Temperature -40° ~ +85°C Storage Temperature -45° ~ +100°C Vibration Sine sweep 1g(0-p)10~50~10Hz each axis Humidity 95%~100% RH Runcom Technologies Ltd. 67 RNU4000BS Base Station User Manual Weatherproof 68 100% Weatherproof Runcom Technologies Ltd.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 76 Producer : GPL Ghostscript 9.06 Create Date : 2015:07:06 13:40:00+03:00 Modify Date : 2015:07:06 13:40:00+03:00 Title : Microsoft Word - Runcom RNU4000BS User Manual -RN-PMG-020615 V-4.1.docx Creator : PScript5.dll Version 5.2.2 Author : TzvimEXIF Metadata provided by EXIF.tools