S E M SEM-Z255 Micro Hi-Fi System User Manual Z 255 BTPFU5W S06 ETL FCC English IM

Download:
Mirror Download [FCC.gov]
Document ID	2784188
Application ID	Cj+eAKM0TiH4/7wQMXblWg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.51kB (193878 bits)
Date Submitted	2015-10-16 00:00:00
Date Available	2015-10-16 00:00:00
Creation Date	2015-07-29 09:00:46
Producing Software	Corel PDF Engine Version 3.0.0.739
Document Lastmod	2015-07-29 09:00:46
Document Title	Z-255-BTPFU5W-S06 (ETL+FCC)_English IM
Document Creator	CorelDRAW
Document Author:	NEWGMA

The lightning flash and arrowhead within the triangle is a warning sign
alerting you of "dangerous voltage" inside the product.
CAUTION
USER MANUAL
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
To reduce the risk of electric shock, do not remove cover (or back). No
user-serviceable parts inside. Refer servicing to qualified service personnel.
CAUTION:
The exclamation point within the triangle is a warning sign alerting you of
important instructions accompanying the product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO DRIPPING OR SPLASHING LIQUIDS.
THE MAINS PLUG IS USED AS THE DISCONNECT DEVICE AND IT SHALL REMAIN READILY OPERABLE.
TO COMPLETELY DISCONNECT THE POWER INPUT, THE MAINS PLUG OF THE APPARATUS MUST BE
DISCONNECTED FROM THE MAINS COMPLETELY. THE MAINS PLUG SHOULD NOT BE OBSTRUCTED
OR SHOULD BE EASILY ACCESSED DURING INTENDED USE.
CAUTION
DO NOT EXPOSE TO DRIPPING
OR SPLASHING LIQUIDS!
PLEASE NOTE: YOU WILL FIND THE RATING
LABEL FOR THIS PRODUCT LOCATED ON
THE BOTTOM OF THE UNIT.
THE MARKING AND RATING LABEL IS LOCATED AT THE BOTTOM OF UNIT ENCLOSURE OF THE APPARATUS.
CAUTION: GROUNDING OR POLARIZATION. THE PRECAUTIONS SHOULD BE TAKEN SO THAT
THE WIDER BLADE OF THE AC PLUG MUST MATCH THE SLOT IN RECEPTACLE "WALL SOCKET".
THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS
FILLED WITH LIQUIDS SHOULD BE PLACED ON THE APPARATUS.
UNDER THE INFLUENCE OF ELECTROSTATIC PHENOMENON, THE PRODUCT MAY MALFUNCTION
AND USER TO POWER RESET.
- KEEP MINIMUM DISTANCES (5cm) AROUND THE APPARATUS FOR SUFFICIENT VENTILATION.
- THE VENTILATION SHOULD NOT BE IMPEDED BY COVERING THE VENTILATION OPENINGS
WITH ITEMS SUCH AS NEWSPAPER, TABLE-CLOTHS, CURTAINS ETC.
- NO NAKED FLAME SOURCE SUCH AS LIGHTED CANDLES SHOULD BE PLACED ON THE APPARATUS.
- ATTENTION SHOULD BE DRAWN TO THE ENVIRONMENTAL ASPECTS OF BATTERY DISPOSAL.
- BATTERY SHALL NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE, FIRE OR THE LIKE.
ELECTROSTATIC DISCHARGE (ESD) PRECAUTION
WHEN ELECTROSTATIC DISCHARGE (ESD) OCCURS AT THE FRONT SURFACE (WHETHER METAL OR
PLASTIC) OR NEAR ANY PART OR ANY BUTTON OF THIS UNIT, OR AT THE USB PORT AND/ OR SD-CARD
SLOTS (IF THEY EXIST ON THIS PRODUCT), THERE MAY BE A POSSIBILITY THAT THE PRODUCT
MAY STOP OPERATION AND/ OR SHUT DOWN IMMEDIATELY. THIS IS A NORMAL CONDITION AND
INTENDED TO PROTECT THE UNIT AND INTERNAL COMPONENTS AGAINST DAMAGE.
IN SUCH A CASE, PLEASE RESET THE UNIT (BY DISCONNECTING AND RECONNECTING AC-POWER
SOURCE) TO REVERT THE UNIT TO NORMAL OPERATION.
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT: UNSICHTBARE LASERSTRAHLUNG TRITT AUS,
WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT DEM STRAHL AUSSETZENI.
VARNING: OSYNLIG LASERSTRÁLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
MODEL: Z-255-BTPFU5W
Micro Digital CD Radio HI-FI System
SPÄRR ÄR URKOPPLAND. STRÁLEN ÄR FARLIG.
ADVARSEL: USYNLIG LASERSTRÁLING VED ÁBNING. NÁR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÁ UDS/ETTELSE FOR
STRÁLING.
ATTNENZIONE: RADIONS LASER INVISIDILE. NON GUARDARE
DIRETTAMENTE NELLA SORGENTE DEL LASER.
ACHTUNG: LASERLINSE NICHT BERÜHREN UNSICHTBARER LASERSTRAHL.
AVISO: A LENTE NUNCA DEVE SER TOCADA.
E-2
CLASS 1 L ASER P RODUCT
KLASSE 1 L ASER P RODUKT
LASER D E C LASSE
LASER D I P RIMA C LASSE
KLASSE 1 L ASER
LASER P RIMERA C LASE
LASER C LASSE 1
KLASSE 1 L ASER P RODUKT
IMPORTANT SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instruction should be read before
the product is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future
reference.
3. HEED WARNINGS - All warning on the product and in the operating instructions should be
adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions should be followed.
5. CLEANING - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a dry cloth for cleaning.
6. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as
they may cause hazards.
7. WATER AND MOISTURE - Do not use this product near water- for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious damage to the product.
Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow the manufacturer's instructions, and should
use a mounting accessory recommended by the manufacturer.
9. A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may causethe appliance and cart
combination to overturn.
10. VENTILATION - Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instruction have been adhered to.
11. POWER SOURCES - This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended to operate from battery power, or
other sources, refer to the operating instruction.
12. GROUNDING OR POLARIZATION - This product may be equipped with a polarized
alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarizes plug.
ALTERNATE WARNINGS - This product is equipped with a three-wire grounding-type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact you electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
13. POWER-CORD PROTECTION - Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and point where they exit from the product.
14. PROTECTIVE ATTACHMENT PLUG - The product is equipped with an attachment plug having
overload protection. This is a safety feature. See Instruction Manual for replacement or resetting
of protective device. If replacement of the plug is required, be sure the service technician has used
a replacement plug specified by the manufacturer that has the same overload protection as the
original plug.
15. OUTDOOR ANTENNA GROUNDING - If an outside antenna is connected to the receiver, be sure
the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting structure, grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
E-3
SEE FIGURE:
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
16. LIGHTNING - For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product due to lightning and power-line
surges.
17. POWER LINES - An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
18. OVERLOADING - Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
19. OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
20. SERVICING - Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards, Refer all servicing to qualified service
personnel.
21. DAMAGE REQUIRING SERVICE - Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally be following the operating instructions. Adjust only
those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to damage and will often require extensive work by a qualified technician to restore
the product to its normal operation.
e) If the product has been dropped or damaged in any way, and
f ) When the product exhibits a distinct change in performance this indicates a need for service.
22. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards,
23. SAFETY CHECK - Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating condition.
24. WALL OR CEILING MOUNTING - The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
25. HEAT - The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
E-4
POWER SUPPLY
- THIS SET WORKS ON NORMAL HOUSEHOLD AC-POWER.
- INSERT THE PLUG OF THE AC-CORD INTO A WALL OUTLET WITH
AC-POWER.
- PRESS THE "ON/ STANDBY" KEY TO SWITCH “ON” THE UNIT.
- PRESS AND HOLD THE "ON/ STANDBY" KEY 3 SECONDS TO SWITCH THE UNIT TO
STANDBY MODE.
- THIS UNIT IS DESIGNED TO OPERATE WITHOUT BEING TOTALLY POWERED "OFF".
IT WILL EITHER BE "ON" OR IN "STANDBY” MODE.
- IN STANDBY MODE, THE BLUE BACK-LIGHT OF THE DIGITAL DISPLAY WILL BE DIMMED
BUT THE DISPLAY WILL SHOW THE CURRENT TIME (CLOCK FUNCTION).
- ANYTIME DURING STANDBY MODE, YOU CAN SWITCH "ON" THE UNIT BY PRESSING
THE "ON/ STANDBY" KEY.
- SAVE ENERGY BY SWITCHING THE SYSTEM TO "STANDBY" MODE WHEN NOT IN USE.
IMPORTANT : HOW TO TELL IF POWER IS "ON" ?
WHEN THE POWER IS "ON" THE ENTIRE DIGITAL DISPLAY WILL LIGHT UP WITH
A "BLUE" BACK-LIGHT. THIS INDICATES THE HI-FI IS SWITCHED "ON".
CONNECTION OF SPEAKER BOXES
14
- UNWRAP THE SPEAKER-CORDS OF BOTH SPEAKER-BOXES AND INSERT THE
LEFT/RIGHT PLUGS INTO SOCKETS IN THE REAR OF MAIN UNIT.
- PLACE THE SPEAKER BOXES AS FAR APART AS POSSIBLE FOR BEST SOUND
EFFECT.
DIGITAL CLOCK FUNCTION
10 11
12
- THE SET HAS A BUILT-IN DIGITAL CLOCK, WHICH IS DISPLAYED WHEN
THE SET IS IN "STANDBY MODE". (THE DISPLAY WILL CONTINUOUSLY SHOW
THE CURRENT TIME). IN THIS SITUATION THE BLUE BACKLIGHT IS NORMALLY
DIMMED (TO SAVE ELECTRICITY).
HOW TO SET CORRECT TIME:
13
SWITCH UNIT TO "STAND- BY" MODE
15
19
16 17
18
LOCATION OF CONTROLS
1. CD DOOR
2. COMPART MENT DOOR
3. SLOT FOR PLACING YOUR SMART PHONE/
TABLET
4. SPEAKER (LEFT)
5. LCD DISPLAY
6. ON/ STANDBY KEY
7. BACK/ TUNE DOWN KEY
8. NEXT/ TUNE UP KEY
9. STO P/ FM MEM./ SLEEP/ SNOOZE KEY
10. PLAY/ PAUSE/ PAIR/ FM MODE KEY
E-5
11. PROGRAM/ PLAY MODE KEY
12. VOLUME DOWN (-)/ ALARM SET KEY
13. VOLUME UP (+)/ CLOCK SET KEY
14. SPEAKER (RIGHT)
15. FM ANTENNA
16. USB CHARGER PORT
17. AUX IN SOCKET
18. SPEAKER OUTPUT SOCKETS
(LEFT & RIGHT)
19. AC CORD & PLUG
PRES S & HOLD CLOCK SET FOR 3 SECON DS
DISPLAY SHOWS 12 HOUR OR 24 HOUR (FLASHING)
TUNE UP OR
TUNE DOWN TO SELECT 12-HOUR
PRES S
OR 24-HOUR CLOCK DISPLAY SYST EM & PRES S CLOCK SET TO CONFI RM
YOUR SELECTI ON
TUNE UP OR
TUNE DOWN REPE ATEDLY TO SET
PRES S
THE CORREC T HOUR IN THE DISPLAY & PRES S CLOCK SET TO CONFI RM
TUNE UP OR
TUNE DOWN REPE ATEDLY TO SET
PRES S
THE CORREC T MINUTE IN THE DISPLAY & PRES S CLOCK SET TO CONFI RM
CORREC T TIME IS NOW SET & WILL BE SHOWN IN THE DISPLAY!
*NOTE:
THAT WHEN THE DIGITAL CLOCK IS NOT SET, THE DIGITAL CLOCK DISPLAY SHALL
CONTINUOUSLY FLASH TO INDICATE THAT THE CORRECT TIME HAS NOT YET BEEN SET.
E-6
OPER ATION OF RADI O
ALARM FUNCTION
- THIS SET HAS A ALARM FUNCTION TO ENABLE YOU T O PROGRAM THE UNIT
AS A WAKE-UP ALARM CLOCK :
HOW TO SET TIMER
1. IN STANDBY MODE, PRESS ALARM SET KEY ONCE.
2. PRESS
TUNE UP OR
TUNE DOWN TO ADJUST THE HOUR OF
THE DESIRED "ON" TIME AND THEN PRESS ALARM SET KEY TO CONFIRM.
3. PRESS
TUNE UP OR
TUNE DOWN TO ADJUST THE MINUTES OF
THE DESIRED "ON" TIME AND THEN PRESS ALARM SET TO CONFIRM.
4. NOW THE WORDING IN THE DISPLAY CHANGES TO SHOW " " (BUZZER ALARM).
5. PRESS ALARM SET KEY TO CONFIRM.
6. FINALLY THE UNIT WILL RETURN TO THE NORMAL DISPLAY, EXCEPT THAT THE
SYMBOL WILL BE SHOWN, TO INDICATE THAT YOU HAVE PROGRAMMED A ON/OFF
ALARM SETTING.
7. IN CASE YOU WISH TO DISABLE THE TIMER, LONG PRESS THE ALARM SET KEY
FOR 3 SECONDS, & THE
SYMBOL WILL DISAPPEARS.
NOTE:
1. THE WAKE UP VOLUME LEVEL WILL GRADUALLY AND AUTOMATICALLY INCREASE
FROM ZERO (0) TO LEVEL 17 WHEN THE WAKE UP ALARM IS ACTIVATED.
THIS CAN NOT BE CHANGED.
2. WHEN THE ALARM COMES ON, CAN PRESS ANY KEY (EXCEPT "SNOOZE" KEY) TO
TURN IT OFF.
SNOOZE FUNCTION
- WHENEVER THE ALARM COMES ON, IT CAN BE TEMPORARILY SUSPENDED
FOR A SHORT PERIOD OF APPROXIMATELY 9 MINUTES, BY PRESSING
THE “SNOOZE” KEY ONCE, "SNOOZE" WILL LIT ON DISPLAY.
- THE ALARM WILL THEN AUTOMATICALLY COME ON AGAIN AFTER APPROXIMATELY
9 MINUTES “SNOOZE” PERIOD HAS ENDED.
- THE PROCEDURE CAN BE REPEATED FOR APPROXIMATELY AN HOUR.
AUTOMATIC POWER OFF SLEEP FUNCTION
- THIS SET HAS A SPECIAL SLEEP TIMER FUNCTION WHICH CAN AUTOMATICALLY
SWITCH OFF THE UNIT. THIS IS USEFUL FOR SLEEPING TO MUSIC.
- AT ANY TIME WHILE THE UNIT IS OPERATING, PRESS AND HOLD THE SLEEP KEY
FOR 3 SECONDS REPEATEDLY TO CHOOSE THE AUTOMATIC POWER OFF TIME.
10
MINS
20
MINS
30
MINS
40
MINS
50
MINS
60
MINS
70
MINS
80
MINS
90
MINS
OFF*
(*OFF MEANS SLEEP TIMER IS DEACTIVATED)
ELECTRONI C VOLUME CONT ROL
- PRESS THE "ON/STANDBY" KEY ONCE TO SWITCH ON THE UNIT.
- PRESS THE FUNCTION KEY REPEATEDLY UNTIL THE DISPLAY SHOWS THE RADIO
FREQUENCY.
- TO IMPROVE FM-RADIO RECEPTION, FULLY EXTEND THE FM-ANTENNA WIRE
AND ADJUST IT'S POSITION.
- USE THE FM MODE KEY TO SELECT THE DESIRED MODE (FM MONO/STEREO).
IN SOME CASES, WHERE RECEPTION IS POOR, IT MAY BE ADVISABLE TO SELECT
"MONO" MODE, TO IMPROVE CLARITY OF THE RADIO SIGNAL.
MANUAL FREQUENCY ADJUSTMENT (SCAN MODE)
TUNE UP OR
TUNE DOWN
- PRESS (AND IMMEDIATELY RELEASE) THE
KEYS TO "SCAN" (MANUALLY ADJUST) THE RADIO FREQUENCY "UP" OR "DOWN"
BY 1-STEP AT A TIME.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH
STEP’S POSITION.
- WHEN A DESIRED FREQUENCY OR STATION IS REACHED. IT CAN BE SAVED
INTO ONE OF THE "MEMORY" POSITIONS. (SEE "RADIO MEMORY" SECTION).
AUTOMATIC FREQUENCY ADJUSTMENT (SEEK MODE)
TUNE UP OR
TUNE DOWN
- PRESS AND HOLD (FOR 2 SECONDS) THE
KEYS TO "SEEK" (AUTOMATICALLY ADJUST) THE RADIO FREQUENCY "UP" OR
"DOWN" TO THE NEXT AVAILABLE RADIO STATION.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY OF THE
NEXT STATION THAT IS FOUND.
- WHEN A DESIRED STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE
"MEMORY" POSITIONS. (SEE "RADIO MEMORY" SECTION).
RADIO MEMORY (STATION P RESET MEMORY STORAGE)
- AT ANY TIME, THE CURRENTLY DISPLAYED STATION OR FREQUENCY CAN BE
STORED INTO ONE OF THE MEMORY POSITION.
- PRESS PROGRAM KEY ONCE, THE MEMORY POSITION WILL SHOWS ON DISPLAY.
- PRESS THE
TUNE UP OR
TUNE DOWN KEY TO SELECT THE DESIRED
MEMORY POSITION TO SAVE THE RADIO STATION. (THERE ARE 30 MEMORY
POSITIONS "P01 TO P30).
- PRESS PROGRAM KEY ONCE TO SAVE THE SELECTED STATION INTO THE
SELECTED MEMORY POSITION.
- REPEAT THE ABOVE STEPS FOR PROGRAMING THE MEMORY STATIONS AS DESIRED.
- TO RECALL A STATION IN MEMORY, PRESS THE FM MEM. KEY REPEATEDLY
TO REACH THE MEMORY POSITION AS DESIRED.
- TO CLEAR THE MEMORY OF AN Y POSITION, SIMPLY SAVE A NEW STATION TO
THE SAME MEMORY POSITION.
- THIS UNIT USES AN ELECTRONIC VOLUME CONTROL (PUSH BUTTON TYPE) .
- TO INCREASE OR DECREASE THE LOUDNESS OF UNIT, PRESS
THE VOLUME UP (+) OR VOLUME DOWN (-) KEYS RESPECTIVELY.
- RELEASE THE KEY WHEN VOLUME LEVEL IS AT THE DESIRED LOUDNESS.
- SOMETIMES, ESPECIALLY DURING LISTENING TO THE RADIO, YOU MAY NOTICE
A "CLICK-CLICK-CLICK" (REPEATING) SOUND WHEN YOU ARE INCREASING OR
DECREASING THE VOLUME. THIS IS A NORMAL CONDITION & THE SOUND WILL
DISAPPEAR WHEN YOU RELEASE THE VOLUME KEY (WHEN YOU REACH THE
DESIRED VOLUME LEVEL).
E-7
E-8
INSERTION & REMOVAL OF DISCS
- WHEN OPENING THE CD-DOOR, ALWAYS ENSURE THE DISC IS NOT IN MOTION
(NOT SPINNING) WHEN YOU OPEN THE CD-DOOR. ALWAYS PRESS STOP
KEY TO STOP THE DISC SPINNING FIRST.
- PLACE A CD INTO THE COMPARTMENT WITH THE LABEL-SIDE (PRINTED SIDE
OF DISC) FACING UPWARDS. PRESS DOWN IN THE CENTER PART OF DISC
UNTIL THE DISC "LOCKS" ONTO THE CENTER SPINDLE.
- WHEN THE CD HAS BEEN PLACED ONTO THE CENTER SPINDLE, GENTLY
LOWER THE CD-DOOR DOWNWARDS UNTIL IT LOCKS SHUT.
- THE CD IS NOW READY TO BE PLAYED.
- TO REMOVE A DISC, FOLLOW THE SAME PROCEDURE AS DESCRIBED ABOVE,
EXCEPT TO REMOVE THE CD INSTEAD OF INSERTING IT INTO THE
COMPARTMENT, BY PLACING ONE FINGER AT THE MIDDLE OF DISC
(CENTER SPINDLE) & THE OTHER AT THE EDGE OF THE DISC & GENTLY
PULLING UPWARDS.
- IMPORTANT : ALWAYS HOLD A CD BY ITS EDGES. AVOID GETTING ANY
FINGER PRINTS, SMUDGES OR DIRT ONTO THE SURFACE OF A DISC. IN CASE
THIS HAPPENS, USE A SPECIAL CD-CLEANING CLOTH OR CLEANING KIT TO
REMOVE THE DIRT OR SMUDGES.
NORMAL CD OPERATION
TURN THE UNIT ON BY PRESS THE
ON/ STANDBY KEY.
INSERT A CD AS DESCRIBED.
PRESS THE FUNCTION KEY UNTIL DISPLAY SHOW "CD".
THE CD WILL SPIN MOMENTARILY AND THE DISPLAY SHOW THE TOTAL
NUMBER OF TRACKS (SONG) OF THE DISC.
- PRESS THE
PLAY/ PAUSE KEY, THE FIRST TRACK (SONG) WILL START
PLAYING. THE DISPLAY WILL INDICATE THE CURRENT TRACK NO. ("01" IF IT IS
THE FIRST TRACK), AND CURRENTLY PLAYING TIME FREQUENCY.
- AT ANYTIME DURING PLAYBACK, PRESS THE
PLAY/ PAUSE KEY TO
PAUSE OPERATION OF THE UNIT. PRESS THE
PLAY/ PAUSE KEY AGAIN
TO RESUME OPERATION AT THE SAME TRACK & POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS THE STOP
KEY TO STOP
OPERATION OF THE SET. THIS WILL RESET THE CD PLAYER TO THE FIRST
TRACK (IF YOU PRESS PLAY AFTER STOP, THE FIRST TRACK WILL ALWAYS
START PLAYING).
- AT ANYTIME DURING PLAYBACK, "PRESS AND RELEASE" THE
TUNE DOWN
OR
TUNE UP KEYS TO SKIP BACKWARDS OR FORWARDS BY ONE TRACK,
AS DESIRED.
TUNE DOWN
- AT ANYTIME DURING PLAYBACK, "PRESS AND HOLD" THE
OR
TUNE UP KEYS TO FAST-REVERSE (REVIEW) OR FAST-FORWARD
(CUE) THE SPECIFIC TRACK, WHICH IS CURRENTLY PLAYING.
E-9
PROGRAM FUNCTION
- THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UP TO
20 TRACKS FOR AUDIO-CD AS DESIRED.
- ALWAYS PRESS THE STOP
KEY BEFORE STARTING THE PROGRAMMING.
- PRESS THE PROGRAM KEY ,THE DISPLAY WILL SHOW "01" AND THE DISPLAY
WILL SHOWN A "MEMORY” SYMBOL, TO INDICATE THAT THE SET IS NOW IN
“MEMORY PROGRAMMING MODE", AT THE FIRST MEMORY POSITION.
- PRESS THE
TUNE UP OR
TUNE DOWN KEYS TO SELECT THE TRACK
(SONG) NUMBER YOU WISH TO BE STORED IN THE FIRST MEMORY (PROGRAM)
POSITION, AND PRESS THE PROGRAM KEY TO CONFIRM YOUR SELECTION.
- WHEN YOU PRESS THE PROGRAM KEY THE DISPLAY WILL ADVANCE TO
THE NEXT MEMORY POSITION (eg. "02").
- REPEAT THE PREVIOUS 2 STEPS, EACH TIME SELECTING ANY TRACK NUMBER
OF YOUR CHOICE TO BE STORED IN THE SUCCESSIVE MEMORY (PROGRAM)
POSITIONS.
- AFTER EACH TRACK NUMBER, REMEMBER TO PRESS THE PROGRAM KEY.
- AFTER A MAXIMUM OF SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBED
ABOVE. IF ALL 20 TRACKS HAD PROGRAMMED, THE DISPLAY WILL SHOWS "FULL".
- ALSO, THE "MEMORY" SYMBOL WILL REMAIN "ON" TO INDICATE THAT YOU
HAVE SAVED A PROGRAM-MEMORY (SEQUENCE).
- PRESSING
PLAY/ PAUSE WILL NOW PLAY BACK THE "SAVED SEQUENCE" IN
THE PROGRAM MEMORY.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY,
SIMPLY PRESS STOP
TWICE, OR SWITCH "OFF" THE SET.
PLAY MODE FUNCTION
- AT ANYTIME DURING PLAYBACK:
- PRESS PLAY MODE KEY REPEATEDLY TO SELECT THE FOLLOWING OPTIONS:
1.
2.
3.
= REPEAT: TO REPEAT THE CURRENT TRACK
ALL = REPEAT ALL: TO REPEAT ALL TRACK
= RANDOM: TO SHUFFLE ALL SONGS IN RANDOM ORDER
USING THE AUDIO LINE IN CONNECTION (AUX-INPUT)
- YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A MP3
PLAYER OR A TV TO THIS UNIT, THROUGH THE HIGH QUALITY AMPLIFIER OF
THIS MUSIC SYSTEM.
- TO CONNECT THE EXTERNAL DEVICE PLEASE USE A STANDARD STEREO
HEADPHONE (3.5MM TO 3.5MM PLUGS) CABLE TO CONNECT THE
"HEADPHONE-OUT OR AUDIO LINE-OUT" OF THE DEVICE TO THE AUX-INPUT SOCKET
OF THIS UNIT.
ON/ STANDBY KEY.
- TURN THE UNIT ON BY PRESSING THE
- PRESS THE FUNCTION KEY TO SELECT "AUX" MODE.
- SWITCH ON THE EXTERNAL DEVICE (eg. MP3-PLAYER OR TV).
- START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME CONTROL
OF THE MAIN UNIT TO THE DESIRED LEVEL.
- REMEMBER TO SWITCH OFF THE UNIT WHEN YOU ARE FINISHED USING THE
EXTERNAL DEVICE.
E-10
BLUETOOTH® WIRELESS PLAYBACK
THE UNIT CAN WIRELESSLY STREAM AUDIO FROM ANY BLUETOOTH ® DEVICE
WITHIN 30 FEET.
SIMPLY PAIR THE DEVICE AND ENJOY WIRELESS PLAYBACK AND CONTROL
FROM YOUR BLUETOOTH® DEVICE.
PREPARE THE UNIT:
- TURN THE UNIT ON BY PRESS THE
ON/ STANDBY KEY
- PRESS THE FUNCTION KEY TO SELECT “BT” MODE.
- THE BT SYMBOL WILL BE FLASHING TO INDICATE PARING IS PENDING.
THE BT SYMBOL WILL REMAIN LIT CONTINUOUSLY WHEN PAIRED.
*NOTE ONLY ONE DEVICE CAN BE PAIRED AND HAVE PLAYBACK FROM AT ANY
GIVEN TIME.
PREPARE YOUR PHONE OR OTHER BLUETOOTH® DEVICE:
- TURN ON THE BLUETOOTH® FUNCTION, THIS IS USUALLY FOUND UNDER GENERAL
SETTINGS OR OPTIONS.
*PLEASE REFER TO YOUR BLUETOOTH® DEVICE’S MANUAL FOR FURTHER
DETAILS.
MAKE THE CONNECTION:
- GO TO YOUR DEVICE’S BLUETOOTH® SETTINGS
- ADD OR SEARCH FOR DEVICES
- IF ASKED FOR A PASS CODE, ENTER “0000”
*THIS IS A ONE-TIME EVENT PER DEVICE. TO PAIR YOUR UNIT TO ANOTHER DEVICE,
REPEAT THE ABOVE PREPARATION AND CONNECTION STEPS.
DISABLING THE CONNECTION:
TO UNPAIR A BLUETOOTH® DEVICE THAT IS ALREADY PAIRED, PRESS AND HOLD
THE PAIR / PLAY/ PAUSE KEY FOR A FEW SECONDS.
VOLUME CONTROL:
INCREASE AND DECREASE VOLUME USING THE VOLUME UP (+) OR VOLUME
DOWN (-) KEYS ON THE UNIT AND THE VOLUME CONTROLS ON YOUR BLUETOOTH®.
*NOTE THAT IF THERE IS NO PLAYBACK, ENSURE THAT NEITHER THE UNIT NOR
YOUR BLUETOOTH® DEVICE ARE SET TO ZERO VOLUME AND THE RIGHT DEVICE
FOR PLAYBACK IS PAIRED.
SPECIFICATIONS
POWER SUPPLY : ........................................ .. AC 100V-240V ~ 50/60HZ
USB Output Power : ........................................ 5V - - - 2A (Standby Mode)
RADIO FREQUENCY : .................................... FM 87.5 - 108 MHZ
SPEAKERS : ...................................................3"X2
Wireless Range (BT) : ................................ ...... 10M (30 Ft.)
FM Station Memory : .................................. ...... 30 Stations
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the product.
NOTE: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If the product does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures : -Reorient or relocate the receiving antenna.
-Increase the separation between the product and receiver.
-Connect the product into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
USB CHARGING PORT
THIS UNIT IS EQUIPPED WITH A DC 5V USB CHARGING PORT ON THE REAR OF UNIT.
TO UTILIZE THIS FEATURE, SIMPLY CONNECT THE DEVICE YOU WOULD LIKE TO CHARGE
(eg. SMARTPHONE OR TABLET) TO A SUITABLE USB CABLE AND PLUG IT INTO THE USB
CHARGING PORT. (THIS FUNCTION IS ONLY ACTIVE WHEN THE UNIT IS PLUGGED INTO
AN HOUSEHOLD AC-POWER). THE EXTERNAL DEVICE WILL BE CHARGED AUTOMATICALLY
WHEN IT IS SUCCESSFULLY CONNECTED, EVEN DURING PLAYBACK.
E-13
E-14

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Page Count                      : 6
Create Date                     : D:20150729090046
Modify Date                     : D:20150729090046
Producer                        : Corel PDF Engine Version 3.0.0.739
Author                          : NEWGMA
Creator                         : CorelDRAW
Title                           : Z-255-BTPFU5W-S06 (ETL+FCC)_English IM

EXIF Metadata provided by EXIF.tools