S Siedle and Soehne Telefon und Telegrafenwerke OHG S850FP DECT Base Station User Manual S 850 0 141359 EN BA indd

S. Siedle & Soehne Telefon- und Telegrafenwerke OHG DECT Base Station S 850 0 141359 EN BA indd

Contents

User Manual

S 850-0EN Operating InstructionsSiedle Scope
Use the cross-shaped control pad and the Enter button in the centre to navigate through all the menus in the cordless handset.Activate your selection using the round Enter button in the centre of the cross-shaped control pad or alternatively using the display button OK or Save. Leave the menu level and jump one menu level higher without saving your input using the red End call button or alternatively with the display button Back. Selected menu points, functions or names in the display have a yellow frame or are shown in yellow. In these operating instructions, these are depicted with a grey frame.Handling instructions are preceded by a point.Navigation in all menusBackPhone volumeSetting the volume for the receiver and handsfree calls.Main menuAccess to the call list, intercom set-tings, general set-tings and phone-book.PhonebookAccess to favourite telephone numbers.Intercom menuAccess to building communication functions (e.g. con-trol and switching).OKOverviewDisplay and navigation
Loudspeaker for audio privacyThe loudspeaker for handsfree calls is located at the back.Status indications in the displayDisplayFrequently used functionsDisplay buttonsControl buttons for menu navigationEnter buttonGreen Pick up buttonDoor release buttonRed End call buttonON/OFF button (hold down for 3 seconds)Button to move back through the menuInput of numbers and lettersStar button for call silencing (hold down for 3 secs.)Hash button to lock the keypad (hold down for 3 secs.)MicrophoneOverviewModel: Siedle Scope9+14:34Monday 21/03/2011Light Door call
2OverviewDisplayStandby modeIn the standby status, the cordless handset shows the time and date in the display, the 4 symbols of the main menu and 2 frequently used functions using display buttons, if these have been set up. Status indications in the displayThe current Siedle Scope status dis-plays are shown along the top of the screen. The reception quality to the base station and the battery charge status are continuously shown. Other functions appear in the form of symbols only when active.Symbols in the standby modeVolumeThe receiver and handsfree volume are set using the Call volume menu.Main menuAccess to the call list, intercom settings, general settings and phonebook.PhonebookAccess to favourite tel-ephone numbers.Intercom menuAccess to building com-munication functions (e.g. control and switching).Status indications in the displayReception qualityVery good to noneBattery charge statusKeypad lockThe keypad lock prevents unintentional operation of the telephone.Missed callsAll calls are counted up to the number nine. If there are more than 9 calls, a plus symbol is shown after the 9.9+Status indications in the displayDoor call forwarding enabledService not availableRequired service cannot currently be used (e.g. external line engaged).Doormatic: enabledCall silencing: Activated9+Light Door call14:34Monday 21/03/2011
3OverviewDisplay and navigationModel: Siedle ScopeDisplaySiedle Scope 4One for all 4Safety remarks 5Disposal 5Getting started Registering the cordless handset at the base station Charging the cordless handset batteryRegistering additional cordless handsets at the base stationSwitching the cordless handset on and off7Incoming calls Keypad lock Dial the required number Holding a call Handsfree Call silencing 9Volume 9Microphone silencing 9Call parking 9Call forwarding 10Ending a call 10Brokering 11Cordless handset 11Charging cradle 11Door release 11Setting the date and time 12Setting the time 12Date settings 13Video 14Phone volume 15Main menu Call lists Intercom settings Doormatic Door call forwarding 19Door call forwarding to the public network telephone19Functions 20Door 21Control Device 21Function 21Settings 22Status 22Setting the time 23Date settings 24Audio settings 25Ringtones 25Phone volume Notifications 27Key tones 27Battery tone 27Signal tone 27Speed dial Making a speed dialling call 29Frequently used functions 29Language 31System 31ECO mode 32Change PIN 32Resetting the base station 34Door call 35Deregistering / registering a handset35Dialling pause 35External line digit New entry 37Phonebook options Making a call to a phonebook entryChange entry 39Deleting an entry 39Intercom menu 40The individual symbols in the Intercom menu 40Frequently asked questions 42Index 43ContentsTechnical additions or printing errors do not constitute grounds for compensation claims.Customer service in the Furtwangen factory+49 7723 63-375These instructions are intended to supplement:The Scope product informationThe In-Home bus: Video system manualThe relevant current edition is located in the download area on www.siedle.de
4Siedle ScopeOne for allA new freedomSiedle Scope is a video indoor sta-tion and a landline telephone in one device. And it’s cordless. That means that wherever you are, whether in the kitchen, the bath-room, the garden or the cellar … Scope gives you a live update of who is standing at the door. Scope thus offers all the functions of a video indoor station, including a hands-free function and a door release button. At the same time, -ephone with excellent voice quality and countless Comfort functions. One for all. New freedom.Scope, the mobile video indoor stationLarge colour displayVideo monitoring with zoom and swivel functionHands-free functionIn-house function control, such as lighting, garage door or blindscan be used in parallelScope, the cordless landline telephoneHigh range and excellent voice quality thanks to the DECT standardHands-free functionErgonomically optimized design and user guidanceECO mode with reduced transmis-sion powerTelephone book, call log and numerous other telephone functionsCompatible with telephones from other manufacturers using the GAP -tures only partially possible.Scope of deliverySiedle Scope cordless DECT tel-ephone with door video function for the In-Home bus. Comprising a base station, cordless handset and charging tray. Scope unites the worlds of door communication and public network telephony, it is a comfort video in-house tel-ephone and DECT telephone in one.-necting cables:2 power supply units1 public network cable1 patch cablePerformance featuresmaterials and fine workmanshipquality thanks to DECT standardtransmission output (max. 0.5 W no load)indoors up to 50 mzoommobile phone, also for door calls including door release (PIN-protected)light, garage door or roller shuttersand all other In-Home devices in the same linehandsets in parallelof other makes in compliance with GAP profilewithout telephone systemCordless handset performance featuresdesign variants 240 x 320 pixel, illuminatedcontrol buttons (call acceptance and door release)NoteThe Scope cordless handset must be kept with the same care and security awareness as a house key, as it can also open your front door from the outside. Ensure that it does not fall into unauthorized hands!
5Safety remarksDangerMounting, installation and servicing work on electrical devices may only electrician. Failure to observe this regulation could result in the risk of serious damage to health or fatal injury due to electric shocks.DangerKeep the charger away from Never immerse the battery in water or salt water!Never dismantle or modify the bat-tery or expose it to heat!Avoid dropping the battery if at all possible!Protect the battery from knocks or impacts, as these can damage the housing!Otherwise there is a risk of explo-sion or battery leakage, which could surroundings. If a battery leaks and the emerging substances come into contact with the eyes, mouth, skin or clothing, rinse the affected area immediately using water and consult a doctor.Only charge the battery in the cordless handset using the provided charging cradle and the original power supply unit.The charging cradle and the power supply unit were developed exclu-sively for use with the Siedle Scope cordless handset. Never use in conjunction with other products or batteries!A risk of overheating and defor-or initiate electric shocks.Do not expose the device to over-heating or excessive pressure!WarningOperating the device not in accordance with its intended pur-pose can cause injury. Do not drop or throw the devices!Do not use the devices if they are damaged, for example if the device housing has been damaged (sharp edges or exposed parts)!WarningInstall the base station in a dry and dust-free location away from direct sunlight. Siedle Scope is not suitable for use in wet rooms or in areas with an explosion risk.The cordless handset and the base station must be set up at least one metre away from other electrical devices. When used close to medical devices, functional disturbances can occur. In such cases, contact your specialist dealer or electrical installer!Only ever use original Siedle power supply units which form a part of the scope of supply.Only use the original Siedle rechargeable battery in the cordless handset.Do not hold the back of the cord-less handset against your ear when it rings or when using the handsfree function! This can result in serious damage to your hearing.When using in conjunction with a hearing aid, it is possible for hum-ming or feedback noises to occur.If the device requires servicing, contact your specialist dealer or elec-trical installer!Modern furniture is coated with an enormous variety of different lacquer of these materials can result in sof-tening of the plastic feet in table-top devices and so impair the surface of the furniture. Please appreciate that the manufacturer is unable to accept any liability.DisposalAll electrical and electronic devices must be disposed of separately from the general house waste at the spe-cially provided municipal waste facility. If a product bears the symbol of a waste bin with a line through it, then it falls under the regulations of Responsible disposal and separate collection of end-of-life devices help to prevent potential environmental and health hazards, and form the basis for the recycling of used elec-trical and electronic devices.Rechargeable batteries should also not be disposed of with the general household waste. When disposing of your end-of-life devices and batteries, please observe the local waste disposal regulations. Details can be obtained from your local authority, waste disposal service or the specialist dealer from which you purchased the product. Before disposing of rechargeable batteries, cover over the contacts with sticky tape or other insulating material to ensure they do not come into direct contact with other objects. Direct contact with other metal objects in waste containers 
Getting startedProcedure:If the display of the cordless handset shows the following mes-sage highlighted in yellow: Base not found, then connect the base sta-tion to the mains power.Also connect the charging cradle with the cordless handset to the mains power.As soon as the base station has been located, you can begin to use the cordless handset.If the registration has failed, con-tact your specialist dealer or elec-trical installer.NotePlease observe the safety and dis-posal instructions relating to the rechargeable battery.This is a li-polymer battery with the following performance capability:Standby: appr. 100 hoursVideo link: appr. 3 hoursAudio link only: up to appr. 10 hoursProcedure:To register an additional cordless handset, disconnect the base station from the mains power. Reconnect the base station to the mains power.The base station now has a 3-minute window in which an addi-tional cordless handset can be reg-istered. This is indicated by a green Also connect the charging cradle with the cordless handset to the mains power.The following message appears on the display on the additionally regis-tered cordless handset: Would you like to register the handset?display button OK.Registering the cordless handset at the base stationYour cordless handset is already registered in the set: The left-hand signal strength symbol indicates the strength of the connection in the status bar at the top. Base not found 14:34Monday 21/03/2011Charging the cordless handset batteryAfter unpacking the cordless handset, the battery charge status must be checked. This is delivered fully charged, but discharge may have occurred during storage and transport. Registering additional cordless handsets at the base stationUp to 8 cordless handsets can be operated in parallel at the base sta-tion. The cordless handset supplied as standard in the set is designated handset 1. Other cordless handsets are numbered through in the order in which they are registered. The prescribed designations for RegistrationWould you like to register the handset?OK
7The following display appears during the registration process:Searching basePlease waitAfter selecting the base, the fol-lowing display appears:Registering handsetPlease waitAs soon as the base station has base with the left-hand display button OK.The cordless handset is now in the ready status. After successful registration, the base station is locked again for new registrations. This is indicated by a continuous green LED light. To register additional cordless handsets, disconnect the base sta-tion from the mains power again and proceed as described above. NoteThe additionally registered cord-less handsets are synchronized to the correct date and time and the same intercom settings as cordless handset 1. Procedure:In order to switch on the handset, press the red End call button for around 1 second.The handset automatically acti-vates the power save mode if it is in the idle status for more than 2 minutes. The display switches off.A hibernating handset switches back on automatically as soon as it is placed in the charging cradle. The display terminates the power saving mode automatically after around 1 second as soon as it is removed from the charging cradle. Registering additional cordless handsets at the base stationLight Door call14:34Monday 21/03/2011Switching the cordless handset on and offDuring the switching on process, a progress bar appears on the display. Getting started
If a display is in the power saving pressed this only reactivates the dis-play and has no other function. Procedure:Incoming calls are picked up using the green Pick up button. If you pick up the call by pressing the Mouth button, the call will be held in the handsfree mode. If the cordless handset is in the charging cradle, the call can also be picked up using the Mouth button on the charging cradle. Procedure:To lock and unlock the keypad, hold down the Hash button until the Key symbol in the status bar at the top of the display appears / disappears. NoteIf the keypad lock is switched on, it is also not possible to call emergency numbers. Procedure:Enter the required call number using the numerical keypad. these are indicated by the display.Corrections can be made using the display button <C.Procedure:To establish a call, press the green Pick up button.Procedure:To establish a call in the handsfree mode, press the left-hand display button with the mouth symbol.If the handsfree mode is active, the mouth symbol is highlighted in yellow.Switching the cordless handset on and offIncoming callsThe call number is visible in the display, provided the caller has not withheld their number. If you have stored the call number with a name in the Scope phonebook, the name of the caller can be read in the display. or Keypad lockThe keypad lock prevents uninten-tional operation of the telephone.The keypad lock switches off automatically when you receive an incoming call. At the end of the call, it switches back on again.Dial the required number+Holding a callHandsfreeIf the handsfree mode is active, the mouth symbol is highlighted in yellow.Getting startedTelephony
9Procedure:To switch the muting function on and off, hold down the Star button until the bell symbol in the status bar at the top of the display appears / disappears.Procedure:Using the left-hand control button, select the minus symbol, or with the right-hand control button select the plus symbol.Procedure:When using the telephone, select the microphone symbol with the line through it on the display using the upper control button. Procedure:Select the dot symbol using the lower control button. Select the telephone number of the user to which you wish to for-ward the call.To establish a call, press the green Pick up button.For successful call forwarding, terminate the conference by pressing the red End call button.If, alternatively, you wish to return to the waiting call, press the Dot button again. Call silencingIf required, all ringtones can be muted. Incoming calls are then only sig-nalled optically at the display. VolumeUsing the symbols + and - it is possible to increase and decrease the volume of the current call; Depending on the call mode, this affects either the receiver or the handsfree speaker volume. -+Microphone silencingUsing the microphone silencing function, you can mute the cord-less handset in the middle of a call should you wish to speak privately to a person in the room. The person at the other end is unable to listen in. The microphone symbol is high-lighted in yellow when the micro-phone silencing function is active, and the cordless handset gives off a warning signal tone.Call parkingThe dot button is the so-called “Flash” button. The function initi-ated by the “Flash” button depends on the telephone system to which the Scope is connected. example, it can be used to park the call to confer with a third party user, to whom the call is then forwarded. Any telephone connected to a PBX extension of the telephone system can be a third party user. Forwarding to a different Scope cordless handset registered at the same base station is carried out using the Transfer display button. Getting startedTelephony
10Call transferIf you have picked up a call, to for-ward the call activate the Forward call display button. The submenu „Call forwarding“ appears showing a list of available handsets. Use the control buttons to select the handset to which you wish to forward the call.display button OK.The call to the selected handset is established.As soon as the call to the selected completed call forwarding process by pressing the red End call button.If you have picked up a door call, to forward the call activate the Options display button.The submenu Options opens up.Select the menu item Forwarding using the lower control button.Now use the control buttons to select the handset to which you wish to forward the call.display button OK.The call to the selected handset is established.As soon as the call to the selected completed call forwarding process by pressing the red End call button.NoteForwarding is not possible if there is no active call (blind transfer).Procedure:To end the call, press the red End call button.If you are speaking in the hands-free mode with the handset in the charging cradle, end the call by pressing the Mouth button on the charging cradle.Call forwardingAny incoming calls, whether from public network telephones or door calls, as well as calls from other bus telephones, can be forwarded to other Scope cordless handsets. Call transferHandset 1Handset 2Handset 3Handset 4Handset 5OK TransferDoor call forwarding–+Door callEarpiece volumeMicrophoneOn OffTransferOK CloseEnding a callCalls are ended using the red End call button.Getting startedTelephony
11Accept the door or public network call with the green Pick up button.By pressing the green Pick up button again, you can accept the second incoming call.The green Pick up button can be used to switch backwards and for-wards between the 2 active calls.By actuating the red End call button, you can refuse the incoming second call. NoteIf a display is in the power saving pressed this only reactivates the dis-play and has no other function. Procedure:Without picking up the cordless handset, accept the incoming call using the Handsfree button on the charging cradle.End the call by pressing the Handsfree button again.Open the door using the Door release button.The front door or storey door is opened, depending on where the door call comes from, using the Door release button with the key symbol. The front door can be opened using the white Door release button even if there is no incoming door call.There is an additional Door release button on the charging cradle. However, this only works if the cordless handset is located in the charging cradle. BrokeringBrokering is used to describe the process of switching backwards and forwards between a door call and a public network call. Cordless handsetIdle statusIn order to save power and to extend the life of the battery, the display is switched off in the idle status. The display switches off automatically around two minutes after the last action. As soon as a call is received or infor-mation is transferred, the display is automatically activated to the ready status. Charging cradleThe charging cradle of your Scope cordless handset is used to charge the battery and offers two additional control buttons. The control buttons are only opera-tional and alight when the cordless handset is placed in the charging cradle and the charging cradle is supplied with power through the power supply unit. Door releaseGetting startedTelephony
12Getting startedSetting the date and timeProcedure:Using the right-hand control button, select the Main menu.In the Main menu, select the set-tings by pressing the right and then the lower control button. display button OK.Procedure:In the Settings menu, select the date and time using the lower con-trol button.display button OK.The Time entry is selected in the Date and time menu.display button OK.Setting the date and timeThe date and time are required in order to show the correct time against incoming calls in the call list.Main menuOK BackSetting the timeSettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackDate and timeTimeDateOK Back
13Getting startedSetting the date and timeThe display shows the current date and time settings. These can be deleted using the display button <C.Enter the current time using the numerical keypad, e.g. 17 for the hour. Then select the Minute settings using the lower control button and enter for instance 25. display button Save.with the message: Time set, and shows the entered time setting. display button OK.In the main menu, select the Settings symbol by pressing the right and then the lower control button.display button OK.In the Settings menu, select the date and time using the lower con-trol button.display button OK.Select the date using the control button.display button OK.The display shows the current date and time settings. These can be deleted using the display button <C.Year: Enter the current year using the numerical keypad.Month: Select Month using the lower control button and enter the current month using the numerical keypad. Day: Select Day using the lower control button and enter the current day using the numerical keypad.display button Save.with the message: Date set, and shows the entered date setting.display button OK.Setting the time Time settingsHourMinuteSave <CDate settingsDate and timeTimeDateOK BackDate settingsYear MonthDaySave <C
14Procedure:Using the central control button, zoom into the video image. Select the required image excerpt using the upper, lower, left and right control buttons. Actuating the control button again disables the zoom function.-ital zoom as the default setting. Open the menu using the Options display button.your selection with OK.To delete the default image excerpt, open the Options menu.Select Disable zoom. display button OK.VideoWhen a call arrives, the Scope cordless handset rings and shows the video image. After pressing the green Pick up button or the Handsfree button with the mouth symbol, the speech connection is established.If another door call is received from a different door, the existing call is ended and the process begins again. Digital zoomWhen you have accepted the video link from the door station, the Digital zoom function allows you to enlarge excerpts of the display image.The zoomed image excerpt can be this case, when the next door call is received, the video image starts with precisely this image excerpt. Getting startedVideo
15Procedure:Using the right and left control buttons (+ and -), set the volume in If you wish to adopt a value, con-button Save.Using the lower control button, select Handsfree volume.Using the right and left control buttons (+ and -), set the handsfree volume in multiple stages.If you wish to adopt a value, con-button Save.Using the upper control button, select the submenu Phone volume.Earpiece volume––++Phone volumeEarpiece volumeHandsfreeSave BackHandsfree––++Phone volumeEarpiece volumeHandsfreeSave BackPhone volume
Main menuCall listsProcedure:Using the right-hand control button, select the main menu.The main menu offers quick access to:Call listsIntercom settingsGeneral settingsPhonebookor Access the call lists by pressing the green Pick up button from the ready status.All callsMissed callsAll calls are counted up to the number nine. If there are more than 9 calls, a plus symbol is shown after the 9.Outgoing callsIncoming callsCall listsThe call list logs incoming and out-going calls with call number, date and time.The call list is subdivided into a number of different lists: Incoming calls, outgoing calls, missed calls and all calls.
17Procedure:The call list symbol is highlighted in yellow.display button OK.First of all the complete call list is displayed.In the status bar of the display, the symbols for different call lists are indicated. Use the right and left control but-tons to switch between the different list types. The active list is the one high-lighted in yellow in the status bar of the display.To call back, select the required user by highlighting in yellow with the control button and press the green Pick up button.To edit the call lists, press the Options display button. Here, the following functions are offered:CallDeleteDelete listSave to phonebookCall listsThe Call lists symbol is highlighted in yellow in the main menu. Main menuOK BackCalls list Company XCallDeleteDelete listSave to phonebookOK BackMain menuCall lists
In the main menu, select the Intercom settings using the control buttons.display button OK.The Doormatic entry is selected.display button OK.Using the right or left control button, select Yes or No. Your selec-tion is highlighted in yellow.display button OK.The following message appears in the display: Doormatic enabled/disabled.display button OK.NoteDespite the Doormatic function being enabled, the door call con-tinues for around 40 secs. If you wish to switch off the call, then set the front door volume to 0. This is done in the Main menu > Settings > Audio settings > Front door, or alternatively mute your Scope cord-less handset using the Star button. However, please note that this will also mute all other incoming calls.Using the right-hand control button, select the main menu.The main menu offers quick access to:Call listsIntercom settingsGeneral settingsPhonebookIntercom settingsThe Intercom settings menu is used switching and control operation with your Scope cordless handset. These functions have to be set by your electrician. Main menuOK BackDoormaticThe Doormatic menu is used to acti-vate and deactivate the Doormatic once this function has been enabled by your electrical installer. If the Doormatic function is enabled, in the ready status the Doormatic symbol appears in the status bar of the display. The Doormatic setting applies to all the cordless handsets registered to the base station and is displayed in the display status bars of the dif-ferent handsets. Intercom settingsDoormaticDoor call forwardingFunctionsOK BackDoormaticEnable Doormatic?Yes NoOK BackMain menuIntercom settings
19Procedure:In the Intercom settings menu, select the entry Door call for-warding using the control button.display button OK.Using the right or left control button, select Yes or No. Your selec-tion is highlighted in yellow.display button OK.The Door call forwarding menu shows the forwarding addresses from your phonebook.Select an entry using the lower and upper control button.or By selecting New entry, you can create a new forwarding address with a name and telephone number.display button OK.The following message appears in the display: Door call forwarding enabled, accompanied by the rel-evant name to which you wish to forward the calls, or disabled. display button OK.Pick up the door call at your public network telephone.For door release, enter your 4-digit pin using the numerical keypad.Press the Hash button.Your front door will be opened from your public network phone. End the door call with the button combination * 0 # before replacing the receiver with the red hang up button, as otherwise the public net-work engaged tone will be audible at the door until timeout.Door call forwardingIn the Door call forwarding menu, the door call is automatically forwarded to the public network telephone. This function exists exclusively for door calls; a door call can only be forwarded to a public network telephone.If you also wish to use the Door release function from your public network telephone, you will have to enter your individual PIN. NoteIf door call forwarding is activated, your Scope cordless handset will no longer ring.Intercom settingsDoormaticDoor call forwardingFunctionsOK BackDoor call forwardingEnable door call forwarding?Yes NoOK BackDoor call forwarding to the public network telephoneIf the Door call forwarding function is activated, your front door can be opened from your public network telephone. For security reasons, this is only pos-sible using an individual PIN.Main menuIntercom settings
20Procedure:In the Intercom settings menu, select the entry Functions using the lower control button.display button OK.Select an unassigned function number in the Functions menu. Up to 15 functions are possible.display button OK.In the New entry menu, the Name entry is selected. Using the letter buttons, enter an unambiguous name for the required function, such as Open garage or Front door light.The name must not begin with a space or a special symbol. Select Type entry using the control buttons. Access the possible function types using the OK display button. Select Wired entry using the con-trol buttons. display button OK.FunctionsThe Functions menu lists the con-trol functions and the internal call functions which have been set up by your electrical installer. It also provides information about function numbers which are still unassigned and can therefore still be used. It is also possible here to delete functions you no longer require. Functions 1 and 2 are preset with a default assignment. Both these functions can, however, be edited by your electrical installer if you require. Functions1 Light2 Last door3457OK BackNameWhen selecting, only choose unas-signed functions. Take care not to overwrite previously set functions by mistake.New entryNameTypeFunction3OK <CTypeIn the Type submenu, assign the function to the relevant function type. On principle, any function can be linked to any function type. By selecting the right type, you ensure that the cordless handset dis-plays the correct user interface when executing the function. There are 3 possibilities to choose from. WiredDoorControl DeviceTypeWiredDoorControl DeviceOK BackWiredSelect this function type if you wish to call a different bus telephone using the function.Main menuIntercom settings
21Select Door entry using the con-trol buttons. display button OK.Select Control device entry using the control buttons. display button OK.The function number is pre-assigned by your selection. Select this using the lower control button.Now save your complete entry by pressing the left hand display button Save.New entryNameTypeDoorFunction3OK BackDoorSelect this function type if the func-tion is to be used to dial a door.New entryNameTypeFunction3OK BackControl DeviceSelect this function type if the func-tion is to be used to switch a control device. FunctionAssignment to the required func-tion number is carried out in the Function submenu. The function number must be identical with the programmed value in the bus in total up to 15 functions can be programmed. New entryNameTypeFunction3Save BackMain menuIntercom settings
22Main menuSettingsUsing the right-hand control button, select the Main menu.In the main menu, select the Settings symbol by pressing the right and then the lower control button.display button OK.The Status menu is highlighted in yellow.display button OK.In the Settings menu, you can obtain information about your cordless handset and carry out general set-tings required for running operation. The following menu points are avail-able:StatusDate and timeAudio settingsSpeed dialLanguageSystemMain menuOK BackStatusThe Status menu provides informa-tion about the model, the used status of the battery, and enabled / disabled functions (Doormatic and call forwarding).SettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackStatusModel: Siedle ScopePP:FP:Battery:Doormatic: enabledDoor call forwarding: Off Back
23Procedure:Using the right-hand control button, select the Main menu.In the Main menu, select the set-tings by pressing the right and then the lower control button. display button OK.In the Settings menu, select the date and time using the lower con-trol button.The Time entry is selected in the Date and time menu.display button OK.The display shows the current date and time settings. These can be deleted using the display button <C.Enter the current time using the numerical keypad, e.g. 17 for the hour. Then select the Minute settings using the lower control button and enter for instance 25. Only plausible entries are possible.display button Save.with the message: Time set, and shows the entered time setting. display button OK.Setting the date and timeThe date and time are required in order to show the correct time against incoming calls in the call list.Main menuOK BackSetting the timeSettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackTime settingsHourMinuteSave <CMain menuSettings
24Procedure:In the main menu, select the Settings symbol by pressing the right and then the lower control button.display button OK.In the Settings menu, select the date and time using the lower con-trol button.display button OK.Select the date using the control button.display button OK.The display shows the current date and time settings. These can be deleted using the display button <C.Year: Enter the current year using the numerical keypad.Month: Select Month using the lower control button and enter the current month using the numerical keypad. Day: Select Day using the lower control button and enter the current day using the numerical keypad.Only plausible entries are possible.display button Save.with the message: Date set, and shows the entered date setting.display button OK.Pressing the red End call button takes you back to the higher-level menu without saving. Date settingsDate and timeTimeDateOK BackDate settingsYear MonthDaySave <CMain menuSettings
25Procedure:Using the right-hand control button, select the Main menu.In the main menu, select the Settings symbol by pressing the right and then the lower control button.display button OK.Select Audio settings in the Settings menu using the lower con-trol button.display button OK.Select Ringtones in the Audio settings menu using the control button.display button OK.Select the required entry in the Ringtones menu using the control buttons.display button OK.Procedure:Using the right and left control buttons (+ and -), set the volume in If you wish to adopt a value, con-button Save.In the Settings menu, you can obtain information about your cord-less handset and carry out general settings required for running opera-tion. The following menu points are avail-able:StatusDate and timeAudio settingsSpeed dialLanguageSystemMain menuOK BackSettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackAudio settingsThe Audio settings menu is used to carry out acoustic settings, adjust the call volume and to assign dif-ferent melodies to different call available to choose from for the dif-ferent types of call.The following menu points are avail-able:RingtonesCall volume settingSignal tonesRingtonesAcoustic settings are performed for:TelephoneStorey callIntercomFront doorVolume–+PhoneVolumeMelodyMarimbaSave BackMain menuSettings
Select the menu item Melody using the lower control button.The Melody selection menu is opened by pressing the central Enter button. Select the required melody using the control buttons.display button Save.In the Audio settings menu, select the submenu Call volume setting using the lower control button. display button OK.Using the right and left control buttons (+ and -), set the volume in If you wish to adopt a value, con-button Save.Using the lower control button, select Handsfree volume.Using the right and left control buttons (+ and -), set the handsfree volume in multiple stages.If you wish to adopt a value, con-button Save.–+PhoneVolumeMelody MarimbaSave BackMelodyPhone volumeThe receiver and handsfree volume are set using the Call volume menu.Audio settingsRingtonesPhone volumeNotificationsOK BackEarpiece volume––++Phone volumeEarpiece volumeHandsfreeSave BackHandsfreeMain menuSettings
27Procedure:In the Audio settings menu, select the submenu Signal tones using the lower control button.display button OK.Select the menu item Key tones using the lower control button.Using the right and left control buttons, select ON or OFF.Your selection is highlighted in yellow.display button OK.Select Battery tone using the control button.Using the right and left control buttons, select ON or OFF.Your selection is highlighted in yellow.display button OK.Select Signal tone using the con-trol button.Using the right and left control buttons, select ON or OFF.Your selection is highlighted by a yellow frame.display button OK.In the Signal tones menu, acoustic signal tones can be switched on and off for different statuses.Audio settingsRingtonesPhone volumeNotificationsOK BackNotificationsKey tonesOn OffBattery toneOn OffSignal toneOn OffSave BackKey tonesEach time a button is pressed, an acoustic signal sounds. These key tones can be switched on or off here. Battery toneThe Scope cordless handset signals a critically low battery status with an acoustic warning. The battery in the cordless handset then requires charging in the charging cradle. This battery tone can be switched on or off here.Signal toneExecuted functions such as Doormatic activation are signalled by an acoustic tone. A signal tone indicates that an action cannot be performed, e.g. implausible inputs for date or time. This signal tone can be switched on or off here.Main menuSettings
Main menuSettingsProcedure:In the Settings menu, select the Speed dialling submenu using the lower control button. display button OK.Select the required Speed dialling number using the control button.Access the Assign speed dial menu using the display button Assign.Speed dialling entries can be assigned from the Phonebook or Intercom.Using the right and left control button, choose between Phonebook or Intercom..Your selection is highlighted in yellow.display button OK.Now select the required Speed dialling assignment using the lower control button. display button OK.Pressing the red End call button takes you back to the higher-level menu.Speed dialFor fast access to favourite users from the phonebook or intercom users or functions, it is possible to assign a speed dialling number from 0 - 9. SettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackSpeed dial5 79I LightII Last doorAssign BackSpeed dialAssign speed dial fromPhonebook IntercomOK Back
29When the Scope mobile handset is in the ready status, press the assigned number for around 3 sec-onds. The user is dialled directly. Frequently used functions:LightDoor callIn the Settings menu, select the Speed dialling submenu using the lower control button. display button OK.Making a speed dialling callFrequently used functionsTwo frequently used functions or user numbers (so-called softkeys) can be indicated in the display for super-fast access using the two display buttons. For this, buttons I and II are reserved in the speed dial-ling menu. These two buttons are assigned a name from the phone-book or an intercom function in the speed dialling menu. In the ready mode, you can use the two buttons at the bottom of the display to access frequently used functions such as light switching or opening the garage, or alternatively favourite telephone numbers.Light Door call14:34Monday 21/03/2011SettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackMain menuSettings
30Select the speed dialling number I (for the left-hand display button) or II (for the right-hand display button) using the lower control button.Select the required Speed dialling number using the control button.Access the Assign speed dial menu using the display button Assign.Speed dialling entries can be assigned from the Phonebook or Intercom.Using the right and left control button, choose between Phonebook or Intercom.Your selection is highlighted in yellow.display button OK.Now select the required Speed dialling assignment using the lower control button. display button OK.Pressing the red End call button takes you back to the higher-level menu.Frequently used functionsSpeed dial5 79I LightII Last doorAssign BackSpeed dialAssign speed dial fromPhonebook IntercomOK BackMain menuSettings
31Main menuSettingsProcedure:Select the submenu Language using the lower control button.display button OK.Select the required language using the lower control button.Your selection is highlighted by a yellow frame.display button Save.SettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackLanguageIn the Language menu, you can select the menu language and the possible special symbols for phonebook entries. There are 10 languages to choose from: Danish, German, English, Spanish, French, Italian, Dutch, Norwegian, Polish and Swedish.<br />LanguageDanskDeutschEnglishEspañolFrançaisItalianoNederlandsSave BackSettingsStatusDate and timeAudio settingsSpeed dialLanguageSystemOK BackSystemIn the System menu, the general settings of your Scope cordless handset are carried out.
32Procedure:Select Eco mode in the System menu using the lower control button. display button OK.Using the right and left control buttons, select ON or OFF.Your selection is highlighted in yellow.display button OK.NoteIf you forget the PIN, you will need to reset the base station to the default settings (details in the next chapter).ECO modeIn the ECO mode, the transmission This reduction of the radio output is intended to reduce electro smog. The value depends on the distance from the base station.This reduces the range of your Scope cordless handset.In the ECO mode menu, the ECO mode is switched on and off.ECO modeECO modeOn OffOK BackSettingsECO mode: OffChange PINDoor call: OnDeregister handsetDialling pauseExternal line digitOK BackChange PINImportant system settings are pro-tected against unauthorized access Number (PIN), as protection against registration and deregistration of the cordless handset or protection of the door release button on the public network telephone. In the Change PIN menu, it is possible to individu-alize the default PIN number (0000) to any optional 4-digit PIN.SettingsECO mode: OffChange PINDoor call: OnDeregister handsetDialling pauseExternal line digitOK BackMain menuSettings
33Main menuSettingsProcedure:Select Change PIN in the System menu using the control button.display button OK.Using the numerical keypad, enter the 4-digit PIN you wish to use.display button OK.it again.display button OK.If the entry is correct, the following PIN changed.display button OK.If the entry is incorrect, rewrite the second PIN entry with the same 4-digit number sequence.Change PIN SettingsChange PINEnter PIN****OK <CSettingsChange PINVerify PIN****OK <CSettingsChange PINPIN changed OK
34Procedure:Unplug the patch cable for the In-Home bus at the base station.The base station can continue to be supplied with power during this process.Then press the PROG button (using a paper clip or similar) and hold it in place.While you continue to hold down the PROG button, plug the patch cable back into the In-Home bus.you can release the PROG button.The status LED on the front of the the RESET is in progress.green, the RESET process is com-pleted.You can now reregister the cord-less handsets which you had previ-ously deregistered.If you did not deregister your cord-less handsets before, the following display appears:Base not foundThen select the entry Deregister handset in the main menu under system settings. In answer to the question Do you want to deregister the handset? Yes. display button OK.The following question appears in the display:Deregistration failed. Register to different base?button OK.The registration process is started.As soon as the base station has been located, you can begin to use the cordless handset.Resetting the base stationWhen the base station is RESET, it returns to the as-delivered status, in other words:The PIN is rest to 0000All registered cordless handsets are deletedThe door forwarding function is deletedThe Doormatic function is deletedAll the In-Home functions are deleted(Print out the settings from the BPS or make a note of the functions acti-vated prior to the RESET and enter the same settings when repeating the registration process.)PowerLineIn-Home Prog.Main menuSettings
35Procedure:Select Door call in the System menu using the lower control button.display button OK.Using the right and left control buttons, select Yes or No.Your selection is highlighted in yellow.display button OK.The following message appears in the display: Door call enabled/disabled.Select Deregister/register handset in the System menu using the lower control button.display button OK.Using the right and left control buttons, select Yes or No.Your selection is highlighted in yellow.display button OK.Depending on the selection, the dis-play shows the following message: Registration succeededDeregistration abortedand:Would you like to register the handset?display button OK.Select Dialling pause in the System menu using the lower control button.display button OK.Now select the required length of the dialling pause using the control button.Your selection is highlighted by a yellow frame.display button Save.Door callIf there are several cordless handsets registered to one base station, it is possible to activate call silencing at any of the cordless handsets in order to ensure that you are not disturbed. Door call Allow door call?Yes No OK BackDeregistering / registering a handsetIn the Deactivate / Activate handset menu, it is possible to register or deregister cordless handsets at the base station. Registration is secured by the default PIN 0000. If you have changed this PIN, your own personal PIN must be used to register. Deregister handset Do you want to deregister the handset?Yes NoOK BackDialling pauseIf you are operating the Siedle Scope at a telephone system, you may require an external line digit. It may be necessary to leave a short and continuing with the call number. The required pause is determined by the customer‘s own telephone system. There are three dial pause -Enter the dial pause individually at all the cordless handsets.Dialling pause0 ms3200 msSave BackMain menuSettings
Select External line digit in the System menu using the lower con-trol button.display button OK.The External line digit entry is selected. Using the numerical keypad, enter the external line digit you wish to use. Generally this is the external line digit: 0.Select the Automatically add entry using the lower control button. Using the right and left control buttons, select Yes or No.Your selection is highlighted in yellow.display button Save.External line digitDepending on the telephone system, Scope may have to automatically dial the external line digit before the call number. Enter the external line digit individu-ally at all the cordless handsets.External line digitExternal line digit0Automatically addYes NoSave BackMain menuSettings
37Procedure:When your cordless handset is in the ready status, select the Phonebook menu directly using the lower control button. Alternatively:In the main menu Settings, select the Phonebook symbol by pressing the lower control button.display button OK.In the Phonebook menu, the new entry is selected.display button OK.The entry Name is highlighted in a yellow frame.Using the input buttons, enter the name entry you wish to use. There are several letters stored behind each button in the numerical keypad. By pressing the button several times, you move from one letter to the next.A short pause between presses will cause the selected letter to appear in your entry. display button Save.Select the Number entry using the lower control button.Enter the required number using the numerical keypad.display button Save.PhonebookIn the Phonebook menu, you enter your preferred users and have direct access to these users. Up to 50 entries are possible in the phone-book of each of the cordless hand-sets registered to the base station.New entryPhonebookNew entryOK BackThe customary special symbols for the set language can also be found by multiple pressing of a numerical button.Sequence of phonebook entriesThe phonebook entries are generally alphabetically listed. Special symbols and numbers have top priority.If you wish to circumvent the alpha-betical sequence of entries, precede the name with a symbol or number. These entries are listed at the top of the phonebook. New entryName:Number:Save <CMain menuPhonebook
The following options are available for making entries in the phone-book:CallEditDeleteSelect the required phonebook entry using the control buttons.Select Options using the display button located on the left below. The following Options menu opens:CallEditDeletePress the green call button to dial the selected user direct. or Select Call in the Phonebook options menu using the lower con-trol button. display button OK.Call: The call to the user listed in the phonebook is established. The display changes to the telephony mode. Phonebook options PhonebookNew entryCompany X......CallEditDeleteOptions BackMaking a call to a phonebook entryIf your phonebook is very extensive, press on the various letters to jump directly to the names starting with the relevant letter. +-+ TransferCompany XMain menuPhonebook
39Procedure:Select Change in the Phonebook options menu using the lower con-trol button. Edit: The name entry can be edited, extended or deleted here. Corrections can be made using the display button <C.Select Number in the Phonebook options menu using the control buttons.The number can be edited, extended or deleted here.display button Save.Corrections can be made using the display button <C.Select Delete in the Phonebook options menu using the lower con-trol button. Deleting an entryUsing the right and left control buttons, select Yes or No.Your selection is highlighted in yellow.display button OK.Change entry Change entryName:Number:Save <CDeleting an entry Deleting an entryConfirm deleteYes NoOK BackMain menuPhonebook
40Procedure:When your cordless handset is in the ready status, select the Intercom menu directly using the left-hand control button.The display in the status bar shows the Intercom settings for the dif-ferent areas.Use the right or left control but-tons to switch between the different areas.The relevant Intercom symbol pre-cedes each entry in the list.If your list contains a large number of entries, use the lower control button to scroll to the next page. All intercom functionsSelectable doorsBus telephones: Calls to wired In-Home usersScope cordless handsetsSwitching and control functions in the In-Home busUsing the Intercom menu, it is pos-sible to execute functions in the building communication mode. Examples include:Switching on the lightDialling last doorCalling an in-house telephoneCalling another Siedle Scope cordless handsetViewing the video image at the door stationA maximum of 15 different func--tional Scope cordless handsets are possible. The latter are automatically entered by the system. Your electrical installer programs these functions. Please refer to the separate In-Home Video system manual for the intercom functions. The individual symbols in the Intercom menuIntercom menu
41
42Frequently asked questionsThere is nothing showing in the display.1 The cordless handset is hibernating. Briefly press any optional button.2 The cordless handset is not switched on.Press the red End call button and hold down for a while. 3 The battery is empty.Charge the battery or exchange it. The cordless handset does not ring.1 The ring tone has been switched offHold down the Star key for 3 seconds.2 The call volume is set to minimumIncrease the call volume.3 Door calls are switched offSwitch the door calls on.4 Door call forwarding is enabledDisable door call forwarding.The cordless handset does not respond when buttons are pressed. 1 The keypad lock is activatedHold down the Hash key for 3 seconds.The person at the other end cannot hear you. 1 You have set the cordless handset to mute using the microphone symbol Press the microphone symbol again.The number of the caller is not displayed.1 The caller has withheld their call number. or2 The number display function has not been enabled.The caller should arrange for number display function to be enabled by their provider.The display says Base not found1 The cordless handset is out of range of the base station Reduce the distance between the cordless handset and the base station.2 The cordless handset has been deregisteredRegister the cordless handset.3 The base station has not been switched onCheck the power supply unit to the base station.Error tone after PIN enquiry / forgotten PIN1 You have entered the wrong PIN.Reset the system PIN to the default setting (0000).You cannot hear a ring tone / dialling tone from the landline. 1 You are not using the supplied telephone cable.Please use the supplied telephone cable.2 The telephone cable is not correctly connected to the base station / the telephone network. Check for correct connection. 3 Your telephone system requires a (different) external line digit / a (different) dialling pause than the one which is set. When you call your cordless handset from a public network telephone, the display of your cord-less handset tells you whether the TC system automatically adds the external line digit for incoming calls or not. Try the various dialling pauses in the Settings > System menu.Take into account the default settings of your telephone system in your Scope cordless handset set-tings. It is not possible to call back the numbers entered in the call list1 Your telephone system automatically adds a 0 as a prefix for incoming calls. For this, you have preselected the external line digit 0 in the system settings. Your telephone system saves incoming calls in the call lists with the zero automatically added. This means that you phone the entries in the call list back with a double 0.of your phone system using the fol-lowing process:Call your cordless handset from a public network telephone.The display on your cordless handset will tell you about the pre-settings of your telephone system, If there is a 0 already entered, select the option No in the system settings under External line digit.Take into account the general default settings of your telephone system in your Scope cordless handset settings.You receive a call from a public network telephone during a door call. If you wish to accept the public net-work call:Reject the door call with the red End call button.Then accept the public network call with the green Pick up button.If a door call is forwarded, after hanging up only the public network engaged tone is audible at the door.Before hanging up, press the button combination * 0 # and then end the call by pressing the red hang up button.
43IndexAAudio settings 25BBattery charge status 2Battery tone 27Brokering 11C Call forwarding 10Call parking 9Call silencing 2Change PIN 32, 33 Charging cradle 11Control Device 20Cordless handset deregister 35register 35DDanish 31Date 12Default PIN number 32Dialling pause 35 Disposal 5Disposal of battery 5Door call 35Enable 35Disable 35Door call forwarding 19Door functions 40Door release 11Door release from public network telephone 19 Dutch 31EECO mode 32Ending a call 10English 31 FFrench 31Frequently asked questions 42Frequently used functions 29function number 21Function type 20Functions 20Functions for Scope cordless handsets 40GGerman 31H  IIdle status 11   Italian 31KKey tones 27 LLanguage 31MMain menu 2Making a speed dialling call 29 Microphone silencing 9 NName 21Navigation 2Norwegian 31 O PPerformance features 4 PIN 32  Making a call to a    New entry 37 Polish 31RReception quality 2Register additional  Ringtones 25SSecurity awareness 4Settings 22Signal tone 27Spanish 31 Standby mode 2Status 22Status display 2Swedish 31Switching and control functions 40System 31TTime 12, 13, 23Type 20, 21VVideo 14, 15Volume 2, 9, 25WWired 20
S. Siedle & Söhne Postfach 1155 78113 Furtwangen Bregstraße 1 78120 Furtwangen Telefon +49 7723 63-0 Telefax +49 7723 63-300 www.siedle.de info@siedle.de Germany© 2011/07.11Printed in GermanyBest. Nr. 0-1106/141359 EN

Navigation menu